Rockford Fosgate RFX9420R Installation & Operation Manual

RFX9320

RFX9320G

RFX9320R

RFX9420

RFX9420R

Installation &

Operation

Installation et fonctionnement

Instalación y funcionamiento

Source Units

INTRODUCTION

TABLE OF CONTENTS

2

Dear Customer,

Congratulations on your purchase of the world’s finest brand of car audio source units. At Rockford

Fosgate we are fanatics about musical reproduction at its best, and we are pleased you chose our

product. Through years of engineering expertise, hand craftsmanship and critical testing procedures,

we have created a wide range of products that reproduce music with all the clarity and richness you

deserve.

For maximum performance we recommend you have your new Rockford Fosgate product installed

by an Authorized Rockford Fosgate Dealer, as we provide specialized training through Rockford

Technical Training Institute (RTTI). Please read your warranty and retain your receipt and original

carton for possible future use.

Great product and competent installations are only a piece of the puzzle when it comes to your

system. Make sure that your installer is using 100% authentic installation accessories from

Connecting Punch in your installation. Connecting Punch has everything from RCA cables and

speaker wire to power line and battery connectors. Insist on it! After all, your new system deserves

nothing but the best.

To add the finishing touch to your new Rockford Fosgate image order your Rockford accessories,

which include everything from T-shirts to jackets and hats.

To get a free brochure on Rockford Fosgate products and Rockford accessories,

in the U.S. call 480-967-3565 or FAX 480-967-8132.

For all other countries, call +001-480-967-3565 or FAX +001-480-967-8132.

PRACTICE SAFE SOUND™

Continuous exposure to sound pressure levels over 100dB may cause permanent

hearing loss. High powered auto sound systems may produce sound pressure

levels well over 130dB. Use common sense and practice safe sound.

Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2

Safety Instructions . . . . . . . . . . . . . . . . . . . 3

Precaution. . . . . . . . . . . . . . . . . . . . . . . . 3-4

Contents of Carton . . . . . . . . . . . . . . . . . . . 4

Installation . . . . . . . . . . . . . . . . . . . . . . . 4-8

Remote (Battery Installation). . . . . . . . . . 4

Installation Considerations . . . . . . . . . . . 5

Mounting Locations. . . . . . . . . . . . . . . . 5

Standard Mount. . . . . . . . . . . . . . . . . . . 6

ISO-DIN Mount. . . . . . . . . . . . . . . . . . . 6

Wiring the System . . . . . . . . . . . . . . . . . 7

Wiring Diagram . . . . . . . . . . . . . . . . . . 8

Source Unit Features . . . . . . . . . . . . . . . . 8-9

NOTE: Review each section for more detailed information.

If, after reading your manual, you still have questions regarding this product, we recommend that

you see your Rockford Fosgate dealer. If you need further assistance, you can call us direct at

1-800-669-9899. Be sure to have your serial number, model number and date of purchase available

when you call.

The serial number can be found on the outside of the box. Please record it in the space provided

below as your permanent record. This will serve as verification of your factory warranty and may

become useful in recovering your source unit if it is ever stolen.

Serial Number: _________________________________________

Model Number: ________________________________________

Operation-Basic. . . . . . . . . . . . . . . . . . 10-13

Initial Set-Up. . . . . . . . . . . . . . . . . . . . 10

Reset Button . . . . . . . . . . . . . . . . . . . . 10

Power ON/OFF . . . . . . . . . . . . . . . . . . 10

Clock Operation . . . . . . . . . . . . . . . . . 12

Mode Selection . . . . . . . . . . . . . . . . . . 12

Operation-Tuner . . . . . . . . . . . . . . . . . 13-14

Operation-CD Player . . . . . . . . . . . . . . 15-17

Operation-Title Programming . . . . . . . . . . 18

Operation-MP3 . . . . . . . . . . . . . . . . . . 19-20

Operation-Type RF DSP Amp Control . . . . 21

Troubleshooting . . . . . . . . . . . . . . . . . . 22-25

Specifications . . . . . . . . . . . . . . . . . . . . . . 26

Warranty Information . . . . . . . . . . . . . . . . 27

SAFETY INSTRUCTIONS

PRECAUTIONS

3

Visit our web site for the latest information on all Rockford products.

GETTING STARTED

Welcome to Rockford Fosgate! This manual is designed to provide

information for the owner, salesperson and installer. For those of you who want quick information

on how to install this product, please turn to the

Installation Section of this manual. Other

information can be located by using the Table of Contents. We, at Rockford Fosgate, have worked

very hard to make sure all the information in this manual is current. But, as we are constantly

finding new ways to improve our product, this information is subject to change without notice.

NOTE: This manual uses abbreviations for the following terms:

TUNER = AM/FM Radio Tuner

CDP = In-Dash CD Player

CDX = CD Changer

AUX = External Auxiliary Input

MP3 = Computer Generated Audio File Format

www.rockfordfosgate.com

This symbol with “WARNING” is intended to alert the user to the

presence of important instructions. Failure to heed the

instructions will result in severe injury or death.

This symbol with “

CAUTION” is intended to alert the user to the

presence of important instructions. Failure to heed the

instructions can result in injury or unit damage.

CAUTION: To prevent injury and damage to the unit, please read and follow the

instructions in this manual. We want you to have enjoyment from this

system, not a headache.

CAUTION If you feel unsure about installing this system yourself, have it installed

by a qualified Rockford Fosgate technician.

CAUTION Before installation, disconnect the battery negative (-) terminal to

prevent damage to the unit, fire and/or possible injury.

!

SOURCE UNIT AND OPTIONAL CD CHANGER

Operating Temperature

Be sure the temperature inside the vehicle is between –10° C and +65° C (+14°F and

+149°F). DO NOT play a disc if the temperature is higher or lower than the operating range.

Moisture Condensation

The CD playback may waver due to condensation. If this occurs, remove the disc from the

source unit and wait approximately an hour for the moisture to evaporate.

Environment Exposure

DO NOT expose the Source Unit or optional CD Changer to any of the following: direct sun

and heat, high humidity, excessive dust, excessive vibration and rain or water.

+65°C

–10°C

4

PRECAUTIONS

INSTALLATION

CONTENTS OF CARTON

Model 9320 or 9420 Source unit

Installation & Operation Manual

Standard Mounting Sleeve

Back strap (taped to box insert)

Chassis Release Keys (2)

Hardware Package

16-pin Power Harness

20-pin Preamp Output Harness

Faceplate Cases (1 Soft and 1 Hard)

IR Remote Control and 2 AAA Batteries

(Small Box Inside Carton)

Handling the Detachable Faceplate

DO NOT drop or cause shock to the faceplate as serious damage may occur. Protect the

faceplate by storing it in the supplied carrying case.

Avoid Mechanical Malfunction

DO NOT grab a disc while it is being automatically loaded into the source unit. Doing this

may cause serious damage to the playback mechanism and/or damage to the disc.

IR REMOTE CONTROLLER

Environment Exposure

DO NOT expose the IR Remote to any of the following: direct sun and heat, high humidity

and rain or water.

Handling the IR Remote

DO NOT drop or cause shock to the IR Remote as serious damage may occur.

COMPACT DISCS

Disc Handling and Care

DO NOT touch the playing side (opposite of label side) of the disc. When handling the disc,

only the outer edges or center hole of the disc should be touched. DO NOT affix any sticker

or label to the disc. DO NOT apply vinyl record spray, anti-static agent, acetone, or any

other volatile chemicals to the disc.

Damaged Disc

DO NOT play a cracked, warped, or damaged disc. Doing this may cause serious damage

to the playback mechanism.

New Discs

The CD player will eject discs that have either been inserted incorrectly or have irregular

surfaces. If a new disc is ejected after loading, feel around the outer edge of the CD and its

center hole. Any small burrs or irregularities could inhibit proper loading of the disc. To

remove the burrs, rub the inside edge of the hole and outside edge of the disc with an object

such as a ball point pen.

•



v

i

c

i

o

u

s

o

u

n

d

s

o

f

t

h

e

j

u

n

g

l

e

•

v

i

c

i

o

u

s

o

u

n

d

s

o

f

t

h

e

j

u

n

g

l

•

v

i

c

i

o

u

s

o

u

n

d

s

o

f

t

h

e

j

u

n

g

l

e

•

v

i

c

i

o

u

s

o

u

n

d

s

o

f

t

h

e

j

u

n

g

l

•

v

i

c

i

o

u

s

o

u

n

d

s

o

f

t

h

e

j

u

n

g

l

e

•

v

i

c

i

o

u

s

o

u

n

d

s

o

f

t

h

e

j

u

n

g

l

e

LIQUID SWORD INC.

REMOTE

Battery Installation

1. Remove the battery cover on the back of the remote.

2 Install two (2) AAA batteries with the polarities correct as show by the diagram inside the battery

compartment of the remote.

5

INSTALLA

TION

INSTALLATION CONSIDERATIONS

The following is a list of tools needed for installation:

Volt/Ohm Meter

Wire strippers

Wire crimpers

Wire cutters

#2 Phillips screwdriver

Battery post wrench

Hand held drill w/assorted bits

1/8" diameter heatshrink tubing

Assorted connectors

Soldering iron

Solder

Heat gun

This section focuses on some of the vehicle considerations for installing your new Source Unit. Pre-

planning your system layout and best wiring routes will save installation time. When deciding on

the layout of your new system, be sure that each component will be easily accessible for making

adjustments.

CAUTION: If you feel unsure about installing this system yourself, have it installed

by a qualified technician.

CAUTION: Before installation, disconnect the battery negative (-) terminal to

prevent damage to the unit, fire and/or possible injury.

Before beginning any installation, follow these simple rules:

1. Be sure to carefully read and understand the instructions before attempting to install the Unit.

2. For safety, disconnect the negative lead from the battery prior to beginning the installation.

3. For easier assembly, we suggest you run all wires prior to mounting your Source Unit in place.

4. Route all of the RCA cables close together and away from any high current wires.

5. Use high quality connectors for a reliable installation and to minimize signal or power loss.

6. Think before you drill! Be careful not to cut or drill into gas tanks, fuel lines, brake or hydraulic

lines, vacuum lines or electrical wiring when working on any vehicle.

7. Never run wires underneath the vehicle. Running the wires inside the vehicle provides the best

protection.

8. Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any

wires routed through metal, especially the firewall.

9. ALWAYS protect the battery and electrical system from damage with proper fusing. Install the

appropriate fuse holder and fuse on the +12V power wire within 18” (45.7 cm) of the battery

terminal.

10. When grounding to the chassis of the vehicle, scrape all paint from the metal to ensure a good,

clean ground connection. Grounding connections should be as short as possible and always be

connected to metal that is welded to the main body, or chassis, of the vehicle.

MOUNTING LOCATIONS

The mounting position of your source unit will have a great effect on the performance of your in-

dash CD Player. The source unit can be installed in a wide range of operating locations. However,

care should be taken to ensure optimum performance.

Engine Compartment

Never mount this unit in the engine compartment. Mounting the unit in the engine compartment

will void your warranty.

Instrument Panel

Mounting the source unit in the instrument panel provides optimum access. The source unit should

be securely mounted using the “Standard Mount” or “ISO-DIN Mount” method to ensure optimum

CD Player performance.

!

6

STANDARD MOUNT

Installing;

• Mount the Locks for the Installation Sleeve

onto the source unit (use supplied screws).

• Mount the Installation Sleeve into a secure

instrument panel.

NOTE: Make sure to mount the Source Unit as

close to horizontal as possible for

optimum CD Player performance.

Mounting Angles of up to ±20˚ from

horizontal can be accommodated.

• Bend Appropriate Tabs on all sides of the

installation sleeve. See Installation Sheet.

• Install Source Unit by sliding unit into installation sleeve until it clicks into place.

• Mount Back Strap securely behind the instrument panel to prevent source unit vibration.

• Back strap Screw should be 6mm max (use supplied screw).

• Connect Antenna to antenna jack on rear of source unit.

Removal;

• Disconnect Back Strap from rear of radio (if used).

• Remove Trim Piece from front of radio.

• Insert Release Keys into left and right sides of source unit to

disengage locks.

• Remove Source Unit from installation sleeve with

release keys.

ISO-DIN MOUNT

Installing;

• Remove Trim Piece and Installation Sleeve from source unit.

• Factory Bracket should align with two mounting holes on

each side of source unit.

• ISO Screws should be 6mm max (use supplied screws).

• Connect Antenna to antenna jack on rear of source unit.

• Install Source Unit into instrument panel.

+20°

-20

°

Horizontal

Lock

Screw

Trim

Sleeve

Back Strap

Trim

Dash

Screw

Factory Bracket

Release Key

INSTALLA

TION

Center Console

Mounting the source unit in the center console provides optimum access. Be sure the installation

does not interfere with the operation of the gear shift or parking brake.

Glove Box

Mounting the source unit in the glove box is adequate, but does not provide easy access. Glove box

mounting should only be done if “Instrument Panel” or ”Center Console,” mounting is not

acceptable (i.e., maintaining integrity of older vehicles with metal dashboards.)

Under Dash

Mounting the source unit under the dash is adequate, but does not provide easy access. Under dash

mounting should only be done if “Instrument Panel,” ”Center Console” or ”Glove Box” mounting is

not acceptable. Mount the source unit off to the side of the driver's area to reduce interference with

the parking brake, gear shift, or operating pedals.

NOTE: The source unit should have a mounting angle within ±20° from horizontal.

7

INSTALLA

TION

WIRING THE SYSTEM

NOTE: See diagram on following page to help you connect your system.

CAUTION: If you do not feel comfortable with wiring your new source unit, please

see your local Authorized Rockford Fosgate Dealer for installation.

CAUTION: Before installation, disconnect the battery negative (-) terminal to

prevent damage to the unit, fire and/or possible injury.

1. Install the 16-Pin Power Harness by connecting the corresponding wires to the electrical and

audio system. Solder and heat shrink all connections for a reliable installation. For each

connection, cut a 1" piece of heat shrink tubing and slide over one of the wires. Strip each wire

3/8" then twist together and solder. Slide the tubing over the connection and shrink the tubing

with a hot air gun until no bare wire is exposed.

2. Connect the BLACK (Ground) wire to chassis ground. Prepare the chassis ground by scraping

any paint from the metal surface and thoroughly clean the area of all dirt and grease. Strip the

end of the wire and attach a ring connector. Fasten the wire to the chassis using a non-anodized

screw and star washer.

3. Connect the YELLOW (Backup) wire to a source of constant +12V (for retaining memory on

user-programmed functions). The source should always have +12V, even when the ignition is off

and the car is not running.

4. Connect the RED (ACC +B) wire (Ignition) to a source of switched +12V (is on only when

ignition key is in “accessory” or “run” position). Connect the RED wire to a switched +12 volt

positive source. The switched signal is usually taken from the ACC (accessory) position of the

ignition. If the vehicle does not have an ACC position, connect the wire to the switched ON

position of the ignition.

5. Connect the ORANGE (Dimmer) wire to the lighting switch terminal. This will dim the main

display by 30% when the headlights are turned on.

6. Connect the LT. BLUE (Remote B+) wire to the “Remote Turn-On” leads of the amplifier(s). This

will turn-on the external amplifiers when the source unit is powered on.

7. Connect the BLUE/RED (Auto Ant.) wire to the “Power Antenna” lead. This will raise a fully

automatic antenna when the source unit is powered on, but only in Tuner Mode.

8. Connect the PINK (Telephone Mute) wire for cell phone mute to the wire on the cell phone

harness that provides ground when the phone rings.

9a. Connecting Speakers – Model 9320 only (Not using external amplifier)

Connect the Speaker Wires to the corresponding speaker leads by soldering and heat shrinking all

connections for a reliable installation. If only one pair of speakers is utilized in the system, use only the

FRONT speaker leads and heat shrink the unused REAR leads to prevent from shorting out. Be sure to

maintain speaker polarity. DO NOT chassis ground any speaker leads as unstable operation may

result.

NOTE: Model 9420 has been specifically designed to be used with an external amplifier with RCA input

connections for the best quality performance.

9b. Connecting Speakers (Using external amplifier)

Install the Preamp Output Harness by plugging the RCA cables into the corresponding extension RCAs

that feed the input of the amplifiers. Be sure to route the signal cables away from any high current

wires to prevent coupling noise from radiated electrical fields into the audio signal. The FRONT

OUTPUT connects to the Front speaker's amplifier. The REAR OUTPUT connects to the Rear

speaker's amplifier. The SUM OUTPUT connects to the Subwoofer amplifier.

10. Connect the AUX (1) and AUX (2) INPUTS to a external audio source (this inserts the audio before the

volume control on the source unit). The input voltage this circuit can accept is 1–3V RMS.

11. The 4-pic DIN receptacle connects to a Rockford Fosgate Type RF DSP amplifier (optional) This is used

for programming the Type RF amplifier directly from the source unit.

11. Connect the AUX INPUT to the external audio source (this inserts the audio before the volume

control on the source unit). The input voltage this circuit can accept is 1–3V RMS.

12. Connect the CD Changer (optional) by plugging the 8-pin DIN cable into the connector located

at the rear of the source unit.

13. Connect the Antenna by plugging the antenna cable into the connector located at the rear of the

source unit. Be sure the antenna is securely grounded to the vehicle for proper radio reception.

!

8

INSTALLA

TION

SOURCE UNIT FEA

TURES

1. OFF – Turns the source unit on and off.

2. DISP – Toggles between different display features in main display; when pressed and held for 1

second, toggles clock between hours and minutes.

3. BAND – Selects which bank of tuner presets (FM1/FM2/AM) should be active.

4. MODE – Selects between TUNER/CDP/CDX/AUX1 modes.

5. ENTER – Enables tracks in MP3 mode.

6. OPEN/EJ – Opens the faceplate and ejects CDs from the in-dash CD

player.

7. UP () – Selects the next radio station in TUNER mode and

selects the next track in CDP/CDX mode.

8. DN {DOWN} ( ) – Selects the previous radio station in TUNER

mode and selects the previous track in CDP/CDX mode.

9. MUTE – Mutes audio in TUNER and AUX1 modes. Pauses the disc

in CDP/CDX mode.

10. MENU/SELECT (Press Volume Knob) – When pressed, selects

between VOLUME, BASS, TREBLE, BALANCE, FADER, and SUM

modes. Press and hold to enter set-up menu (see Setup Options).

Press to enter character when using the Programmable Title option.

11. VOLUME (Rotate Volume Knob) – Used to control volume level.

Adjusts default levels during set-up options. Selects characters when

using the Programmable Title option.

12. R – Infrared eye for remote operation.

13. PRESET 1/SCAN – Selects radio preset #1 in TUNER mode and scans each track on the disc in

CDP/CDX mode.

14. PRESET 2/RPT – Selects radio preset #2 in TUNER mode and repeats the current track in

CDP/CDX mode.

15. PRESET 3/RDM – Selects radio preset #3 in TUNER mode and selects tracks at random in

CDP/CDX mode.

16. PRESET 4/DOWN – Selects radio preset #4 in TUNER mode, or previous disk in CDX Mode.

17. PRESET 5/UP – Selects radio preset #5 in TUNER mode, or next disk in CDX Mode.

18.

PRESET 0/ROOT – Selects radio preset #0 in TUNER mode and returns unit to root directory in

MP3 mode.

19. T-ACC – Allows you to enter the track number you want manually .

20. D-ACC – Allows you to enter the disc number you want,CDX mode (available only for 8 disc

player).

21. AS – Press to store strongest radio stations in each tuner bank in AUTO STORE mode.

22 PUNCH – Enables bass and treble response to be boosted at all volume levels.

IMPORTANT: The communication BUS used in Rockford Fosgate model RFX9220 is used only for CD changer

model RFX8810, and is not backward compatible with older RFX models. Rockford Fosgate

recommends connecting only the appropriate RFX models together. Rockford Fosgate does not

assume responsibility when using other manufacturers’ source units with Rockford Fosgate CD

changers (or vice versa). The 4-Pin DIN communication BUS used is for connection to the

Rockford Fosgate Type RF DSP amplifiers with the 4-Pin DIN connection only.

9

SOURCE UNIT FEATURES

10

INITIAL SETUP

NOTE: Items shown in () refer to remote control functions.

DETACHABLE FACEPLATE

The faceplate is detachable as a theft deterrent.

To Detach the Faceplate:

1. Press the Open Button to cause the faceplate to slide down and forward.

2. Press the release button on the bottom front edge of the faceplate and

slide the faceplate away from the unit.

3. The faceplate bracket will automatically close after 5 seconds.

To Attach the Faceplate

1. Make sure that the faceplate bracket is in the closed position.

2. Press the faceplate against the front of the unit until it clicks into place.

CAUTION: Do not attempt to attach the faceplate to the faceplate bracket when the

bracket is in the open position. You may cause damage to the

mechanism that may void your warranty

3. If desired, the faceplate can be permanently attached by affixing it to the bracket with the

screw provided.

RESET BUTTON

CAUTION

: Do not press the Reset Button too hard or you may cause damage that

may void your warranty. If you need assistance, please consult an

Authorized Rockford Fosgate Dealer.

1. Follow the instructions above to detach the faceplate.

2. Insert a paper clip or other slender object into the Reset Button hole in the lower left corner of

the unit and gently press it in until the button clicks.

POWER ON/OFF

1. Press the OFF button to turn the radio on.

2. Press the OFF button again to turn the radio off.

Any Button Wake-Up

Press any button, except OPEN or DISP to “wake-up” the radio from sleep mode.

NOTE: When the radio is off, “sleep mode”, the clock will be displayed.

OPERATION – BASIC

!

Push

!

11

OPERATION – BASIC

VOLUME KNOB/TONE CONTROLS

The Volume knob is a multifunction controller and handles

the Volume, Tone Controls, and Setup Options, see below.

To Control Volume

1. Turn the VOLUME knob clockwise to raise volume.

2. Turn the VOLUME knob counter-clockwise to lower

volume.

To Adjust Tone Controls

1. Press the VOLUME knob repeatedly to cycle through

BASS > TREBLE > BALANCE > FADER > SUM >

VOLUME.

2. Turn the VOLUME knob to increase, clockwise, or

decrease, counter-clockwise, the selected function.

Source Tone Memory

Individual Bass & Treble settings are memorized for TUNER / CD PLAYER / CD CHANGER / AUX1 /

AUX2.

NOTE: If no adjustment is made after 5 seconds, the MENU knob will revert to VOLUME mode.

SETUP OPTIONS

The list below shows the default Setup Options. The bracketed items are

the alternate options contained within each Setup Option.

Selecting Options

1. Press and hold the VOLUME knob for about 1 second until the first

Option appears {RF AMP DSP / FOR SETUP MENU}.

2. Press the VOLUME knob repeatedly to cycle through all Setup

Options. The first three options only affect the Tuner Mode.

3. To change an Option, press the UP or DN {Down} Button

(or ).

4. To store, wait 5 seconds and the Display will return to the last Mode

shown.

• RF AMP DSP / FOR SETUP MENU — Enters into setup control menu

when connected to a TYPE RF DSP Amplifier.

• DX [LOCAL] — Adjusts the sensitivity of the tuner for rural conditions

where there are weak radio stations while Local adjusts the sensitivity for

city conditions where there are several strong radio stations.

• AMERICAS [EUROPE/AUST] — Allows tuning of frequencies available in

different parts of the world.

• PROGRAM PLAY [EJECT MUTE] — Plays the Tuner after you eject a CD while Eject Mute mutes

the Tuner after you eject a CD.

• VOLUME BAR ON [VOLUME BAR OFF] — Displays the Volume Bar at the right side of the

Front Panel while Volume Bar Off turns it off.

• INI VOL 15 — Sets the maximum Initial Volume when the unit turns on. Initial Volume sets

point of maximum volume when the unit is turned on. If the volume setting was lower than the

initial volume setting when the unit is turned off, then the lower volume will be used at turn on.

If the volume setting was higher than the initial volume setting, then the initial volume setting is

used at turn on. This feature prevents accidental high volume turn on as well as allows high

volume settings to be retained in case another preamplifier is the system’s main volume control.

SEL

ENT

Press Knob

Press & Hold Center

Turn Knob

Remote

12

OPERATION – BASIC

• CONTRAST [VIEW +10] — Controls the view angle of the display. Allows adjustment (from -5

to +26) for best visibility.

•

SUM FLAT [80HZ] — Means third pair of RCA pre-outs is full-range while 80Hz means that the

pre-outs are crossed-over 80Hz low-pass for subwoofer use.

• PANEL AUTO [PANEL MANU] — Automatically opens and closes Panel when loading or

ejecting discs while PANEL MANU allows the front panel to remain open and CDs to be

manually loaded or ejected. Allows use of radio with the panel down.

• SCROLL ON [SCROLL OFF] — Titles scroll across panel screen. Scroll Off prevents scrolling.

• AUX1 IN 0 [+6, –6] — Allows you to boost the input volume of a weak external audio source

or diminish a powerful one. Useful for external sources: MP3 players, video games, VCPs, etc.

• AUX2 IN 0 [+6, –6] — Allows you to boost the input volume of a weak external audio source

or diminish a powerful one. Useful for external sources: MP3 players, video games, VCPs, etc.

CLOCK OPERATION

Setting the Clock Hours

1. Press and hold the DISP button for 1 second until the hour flashes.

2. Press UP or DN {Down} button to set the hour.

Setting the Clock Minutes

1. Press and the DISP button a second time and the minutes will flash.

2. Press UP or DN {Down} button to set the minutes.

Your settings will be saved after the clock has flashed for 5 seconds.

NOTE: When the radio is off (sleep mode) the clock will be displayed.

MODE SELECTION

Press the MODE button repeatedly to cycle through the following modes:

• CDP PLAY — Enables CD Player if a CD is inserted.

• AUX MODE [AUX1 / AUX 2]— Allows for an external audio source to

attach to the sound system.

• RADIO — Enables the Tuner.

MUTE

1. Press the MUTE button to dampen the volume.

2. Press the MUTE button a second time to revert the audio to the

previous level.

NOTE: The panel will display MUTE until the function is canceled.

PUNCH

The Punch button enables the bass and treble response of the audio output to

be boosted for all listening levels.

1. Press the PUNCH button to enable the Punch feature.

2. Press the PUNCH button again to disable.

NOTE: The panel will display "Punch" when the Punch feature is on.

13

OPERATION – BASIC

PANEL DISPLAY

Tuner Mode:

The panel will display RADIO, the band, FM1, FM2 or AM1, and the station frequency, unless the

default has been changed to TITLE DEFAULT and a station title has been programmed in.

CD or CDX Modes

While playing a disc the panel will display CDP PLAY or CD CHANGER PLAY, the track number

and the time played, also the disc number if in CDX mode, unless the default has been changed to

TITLE DEFAULT and a disc title has been programmed in.

All Other Modes

The panel will display AUX MODE and AUX1 or AUX2, unless the default has been

changed to TITLE DEFAULT and a title has been programmed in.

PANEL DISPLAY DEFAULT

To set the default, press and hold the DISP button until the hours on the clock begin

blinking. Immediately pressing MODE button allows selection of the default Display

by toggling between Tuner frequency, or track time in CD Mode, and station or disc

name, if titled. See PROGRAMMING TITLES for information.

NOTE: A maximum total of 100 titles can be programmed into the unit.

OPERATION – TUNER

SELECTING A BAND

Press the BAND button repeatedly to cycle through FM1, FM2, and AM. The

act of selecting the band automatically enables that band.

TUNER OPTIONS

DX and AMERICAS are the default Tuner Options settings. The bracketed

options are alternate options.

• DX [LOCAL]

• AMERICAS [EUROPE/AUST]

• PROGRAM PLAY [EJECT MUTE]

Selecting Tuner Options

See SETUP OPTIONS to change tuner options.

SELECTING A STATION

Press the UP or DN {Down} Button ( or ) once and the Tuner will rapidly proceed to the

next (UP) or pervious (DOWN) station.

Press and holding either the UP or DN {Down} Button ( or ) for 1 second will put you into

TUNER MANUAL mode. You can now manually search up or down at a rate of one digit per click

(pressing and holding the UP or DN {Down} Button ( or ) will allow rapid searching).

PRESET BUTTONS

Each Tuner mode—FM1, FM2, and AM—has 10 presets for a total of 30 presets.

To Set a Preset Button

1. Tune the Tuner to the station you wish to program.

2. Press and hold any preset button (1 to 0) for five seconds and it will program that setting.

14

OPERATION – TUNER

AUTO STORE

If you want the Tuner to select the 10 most powerful stations in order of their

signal strength and assign them to Preset buttons 1 to 0, you can use Auto

Store.

1. Press and the AS button and the Tuner will scan the entire dial.

2. Auto Store will store radio stations independently in the selected tuner

bank (FM1/FM2/AM).

PROGRAMMING STATION TITLES

The name of a Station can be stored in memory using up to 10 characters as a title.

See PROGRAMMING TITLES at the end of the OPERATION-CD PLAYER section.

Available on International R.D.S. Models Only

AF/TP MODE

TP (Traffic Program) Mode will automatically switch to receive a Traffic Announcement regardless of

the current operating mode of the unit. EON TA are stations that do not have a TRAFFIC PROGRAM

but can provide information on other radio stations that do.

AF (Alternative Frequencies) Mode compares the signal level of the current station with the signal

level of other alternative frequencies on the same radio network (see PTY Mode). If the AF provides

a stronger signal than the current frequency, the radio will switch to the stronger AF.

Traffic Program Mode (TP)

1. Press the AF/TP button to engage TP Mode, and again to disengage TP Mode.

2. When TP is blinking, TP Mode is on and there is no TP DATA to receive.

3. The SEEK or AS function will stop only at radio stations providing TP or EON TA.

Alternative Frequencies Mode (AF)

1. Press and hold the AF/TP button for 1 second to engage AF Mode.

2. Press and hold AF/TP again for 1 second to disengage AF Mode.

PTY MODE

PTY (Program Type) can search for radio stations via MUSIC MODE or SPEECH MODE networks.

Music Mode categorizes radio stations into Pop, Rock, Modern Music, Light, Classics, and others.

Speech Mode categorizes music into News, Affairs, Info, Sports, Education, Drama, Culture, and

Science. REG (Region Mode) will switch the station to another that has the same PI CODE (station

that provides exactly the same program) but in a different REGION.

Program Type Mode

1. Press the PTY button to cycle through MUSIC,

SPEECH, and PTY OFF.

2. Press the PRESET button that corresponds to the

mode type (refer to chart).

Region Mode

1. Press and hold the PTY button for 1 second to

turn on Region Mode.

2. Press and hold the PTY button again for 1

second to turn off Region Mode.

NOTE: The LCD will display “REG” when AF and

REG modes are on.

KEY Music Mode Speech Mode

M

1

POP M NEWS

M

2

ROCK M AFFAIRS

M

3

M.O.R.M. INFO

M

4

LIGHT M SPORT

M

5

CLASSICS EDUCATE

M

6

OTHER M DRAMA

M

7

– CULTURE

M

8

– SCIENCE

M

9

– VARIED

15

OPERATION – CD PLAYER

Basic Operation

NOTE: This system will play AUDIO CDs created on a Macintosh

NOTE: This system will play CD-R and CD-RW discs.

To Play a CD

1. Press OPEN button and the Front Panel will slide open.

2. Insert a CD and the Front Panel will slide closed after 5 seconds (PANEL

AUTO).

3. CDP PLAY will auto-select and the CD will begin playing track 1

immediately.

4. Use UP or DN {Down} Button ( or )to change tracks.

To Eject a Disc

1. Press the OPEN button for 1 second, "EJECT" appears on the display and

the Front Panel will slide open and eject the disc.

2. Press the OPEN button while Front Panel is open, or wait 5 seconds and the Front Panel will

auto-close (PANEL AUTO).

NOTE: If OPEN is pressed for less than 1 second while in Panel Auto mode, the Front Panel will

open and Eject will not be engaged.

Panel Display

While playing a disc the panel will display CDP PLAY or CD CHANGER PLAY, the track number

and the time played, also the disc number if in CDX mode, unless the default has been changed to

TITLE DEFAULT and a disc title has been programmed in. See PANEL DISPLAY DEFAULT in

OPERATION-BASIC.

Advanced Operation

The following also works with the optional CDX Multi-Disc Changer if it has

been installed.

NOTE: Items shown in () refer to remote control functions.

Track Selection

1. Press the UP Button ( ) to select the next track on the disc.

2. Press the DN {Down} Button ( ) to select the previous track.

Considerations

CDP MODE: The disc will start over at track 1 again after the last track plays.

CDX MODE: When the last track number on the current disc is reached, the

next disc will load in the CD changer and begin playing track 1.

To Play Tracks at Random

1. Press the 3/RDM button to randomize the tracks on a disk. If you have

a multi-disc changer, press and hold the 3/RDM button for 1 second to

randomize the discs and tracks.

2. To cancel, press the 3/RDM button a second time.

NOTE: The panel will display RDM until the function is cancelled.

MODE BAND

ENT

Remote

16

OPERATION – CD PLAYER

To Repeat a Track

1. Press the 2/RPT button to to repeat the track currently playing..

2. To cancel, press the 2/RPT button a second time. Pressing the 1/SCAN

or 3/RDM button will also cancel repeat, or pressing and holding the

UP or DN {Down} Button ( or ).

NOTE: The panel will display RPT until the function is cancelled.

Forward/Reverse

Press the DN {Down} Button ( ) and the player will take you to the start of

the same track as long as that track is more than 10 seconds in. If the track is

less than 10 seconds in, pressing the DN {Down} Button ( ) will take the

player to the beginning of the previous track. Pressing the UP Button ( ) takes

you to the next track.

Fast Forward/Reverse

1. Press and hold the UP Button ( ) to fast forward the track.

2. Press and hold the DN {Down} Button ( ) to fast rewind the track.

NOTE: The panel will display the elapsed time as long as the UP or DN {Down}

Button ( or ) is pressed.

Track Scan

Track Scan plays the intro to each track for 10 seconds before moving to

the next track on the currently playing disc.

1. Press the 1/SCAN button to begin track scan mode.

2. To cancel, press the 1/SCAN (button a second time.

NOTE: The panel will display 1/SCAN, the CD track number and elapsed

time for 10 seconds for each track until the function is cancelled.

Pause CD

1. Press the MUTE button to pause the CD.

2. Press the MUTE button a second time to resume playing the disc.

NOTE: The panel will display PAUSE and the track number until the

function is canceled.

Direct Track Access

Direct Track Access allows any track to be immediately selected and played. This method is faster

than manually cycling through each track on the disc.

1. Press the T-ACC button to select Direct Track Access mode.

2. Press the number, 1-2-3-4-5-6-7-8-9-0, to access the desired track on

the disc.

EXAMPLE: Pressing the T-ACC button, then 01 takes you to track 1,

pressing 12 takes you to track 12 and so forth. Pressing just 1

digit, 7, will take you to track 7 after 5 seconds.

MODE BAND

ENT

Remote

17

OPERATION – CD PLAYER

RFX8810 CD Changer Operation (Optional Accessory)

Magazine Eject

1. Press the EJECT button to release the disc

magazine from the CD changer.

NOTE: The panel will display NO CD, if in CDX

mode, then go to AUX1 mode.

CD Changer Reset

Press the RESET button if the changer gets jammed

during operation.

Loading Disc to the Magazine

1. Pull out the desired disc tray number from the magazine.

2. Place the disc into the magazine, label side up.

3. Push the disc tray back into the magazine.

NOTE: Discs numbers are arranged from the bottom up.

Loading the Magazine to the CD Changer

The INSERT IN THIS DIRECTION arrow indicates the proper direction that

the magazine should be loaded into the CD changer.

CAUTION: Avoid installing or leaving the magazine where it

would be subject to high temperatures such as

from direct sunlight or from hot air from the

heater. Doing so will damage the unit.

CD Changer Mode

1. Press the MODE button until CD CHANGER PLAY is displayed.

2. The CD changer will immediately begin playing track #1 of the first available disc.

3. If the changer was previously initialized, the changer will resume playing the last track

initialized.

Disc Selection

1. Press the PRESET 5–UP button to select the next disc in the magazine.

2. Press the PRESET 4–DOWN button to select the previous disc in the

magazine.

3. Press the D-ACC button and numbers 1-8 for direct disc access.

Panel Display

While playing a disc the panel will display the track number and the time

played, also the disc number, unless the default has been change to TITLE

DEFAULT and a disc title has been programmed in. See PANEL DISPLAY

DEFAULT in OPERATION-BASIC.

NOTE: When the last track # on the current disc is reached, the next disc

will load and begin playing track #1.

LABEL SIDE UP

EJECT

RESET

8

5

6

1

2

3

4

7

R75

LABEL SIDE UP.

INSERT IN THIS DIRECTION

PLACE COMPACT DISC INTO MAGAZINE WITH

.

COMPACT

DIGITAL AUDIO

PLACER LE DISQUE COMPACT DANS LE

CHARGEUR, FACE ETIQUETEE VERS LE HAUT.

!

18

OPERATION – TITLE PROGRAMMING

Programmable Disc Title Memory

NOTE: A maximum total of 100 titles can be programmed into the unit.

The name of a Station, CD, AUX1 or AUX2 channel can be stored in memory using up to 10

characters as a title.

Title Memory

1. Select the mode you are going to be titling, (Tuner, CDP, CDX, AUX1 or AUX2). If in tuner

mode, select the station to be titled.

NOTE: The disc to be titled must be in the unit, either in CDP or CDX, and selected.

2. Press and hold the BAND button for 1 second and the first digit of the

10-digit front panel will begin to blink.

3. Press the DISP button to cycle through the following character types:

Type 1: (space)ABCDEFGHIJKLMNOPQRSTUVWXYZ

Type 2: abcdefghijklmnopqrstuvwxyz

Type 3: 0123456789

Type 4: /\\.+?!*’")

4. Turn the VOLUME knob to select the proper character.

5. Press the VOLUME knob to move to the next space.

6. Press and hold the VOLUME knob for 1 second to

store the title into memory.

Title Erasing

1. Press and hold the MUTE button for 1 second.

2. Turn the VOLUME knob to select the title for erasing.

3. Press and hold the VOLUME knob for 1 second to

erase the title.

Press Knob

Turn Knob

19

MP3 Player Operation — Basic Playing

NOTE: RFX players do not recognize MP3 CDs created on a Macintosh.

NOTE: RFX players recognize MP3’s recorded on either CD-R or CD-RW discs.

With support for multi-session as well.

NOTE: Playability may depend on the type of CD-R/CD-RW used, CD surface condition, CD writer

performance and condition and/or software used. For more information, visit our website.

To Play an MP3 Disc

1. Press OPEN button and the Front Panel will slide open.

2. Insert an MP3 disc and the Front Panel will slide closed after 5 seconds (PANEL AUTO), or

press OPEN to close immediately.

3. CDP PLAY will auto-select and the MP3 disc will begin playing track 1.

4. Press the UP and DN {Down} buttons ( or ) to go forward and backward when

changing tracks.

NOTE: Random (RDM), repeat (RPT), PAUSE and EJECT work the same as a regular CD.

Negotiating the MP3 Directory

The ROOT Level

The ROOT Level contains the name of the disc, but no folder or song information. The first song on

the disc will automatically begin playing when a disc is inserted.

Directly Selecting a Song by Title

The MP3 file management system is a folder-based system similar to the

Windows™ File Manager. Because of this, the UP or DN {Down} Buttons

( or ) function differently than they do in CD Mode. Instead of going

forward or backward through your disc respectively, they go up and down

through the file list.

1. Press the ROOT button and the display will show the disc name. The

display will then immediately switch to show the name of the first folder

on the disc and display it for 5 seconds. If no action is taken during this 5

second period, the display will default back to the song currently playing.

2. While the name of the first folder is showing, press the DN {Down} Button

( ) to scroll through the list of folders. Press the UP Button ( ) to

scroll back up through the folders.

3. Press the ENTER button (ENT) and the name of the first song in the

selected folder will be displayed.

4. Press the DN {Down} Button ( ) to scroll from the first song

contained in the selected folder. Press the UP button ( ) to scroll back

through the songs.

NOTE: If The song name will remain displayed for 5 seconds in steps 1

through 4 above. If no action is taken during this 5 second period, the

display will default back to the song currently playing.

5. Press ENTER (ENT) to select the song and the song will begin playing.

NOTE: If no disc is loaded into the CD player, NO CD will be displayed and the source unit will

revert to AUX1 mode.

OPERATION – MP3

Remote

DN {Down} Button

When playing an MP3 track, pressing the DN {Down} Button ( ) will take you to the beginning

of the previous track. For example, if listening to track 3, pressing the DN {Down} Button ( )

goes to the beginning of track 2, not the beginning of track 3.

However, if playing a regular audio CD track and the DOWN button is pressed, the player will take

you to the beginning of the same track as long as the playing track has been playing for more than

10 seconds. If the track is within 10 seconds of its beginning, pressing the DN {Down} Button ( )

will take the player to the beginning of the previous track.

Fast Forward/Fast Reverse

This function is possible in MP3 Mode, but the time will not display and there will be no sound.

Maximum Writing Speed and Bit Depth

The maximum speed of the CD ROM burner accepted by the RFX units is 12X. The maximum bit

rate range possible is 32kb/sec–320kb/sec. For best performance of scrolling display, before creating

a file system in your CDR burning program, select the CD layout properties menu and file system

tabs. Use JOLIET file format, this allows a maximum of 32 upper and lowercase scrolling characters

to be displayed.

NOTE: Make sure that when a MP3 CD is burned that it is formatted as a data disc and NOT as an

audio disc.

Programmable Titling

Programmable Titling is not available in MP3 mode. However, default is selectable to track/time or

song title on disc.

Directory Structure

The MP3 directory is set up in three levels and is

comprised of three components: (1) the Root, (2)

Folders, and (3) Songs. Songs are played in the order

and level in which they are located. As shown in the

diagram to the right, all songs in Level 2 are played

before the songs contained in Level 3 or lower. These

levels are descriptive of the function of having songs

in folders and subfolders. Any song in a level below

Level 3 is treated as though it were in Level 3, but

will play in the level order as shown. The songs in

the diagram at the right are numbered in the order

they will play.

NOTE: Songs located in subfolders will not display

when scrolling within the folder. Songs and

folders will display in the same order as they

appear in your file manager on your PC.

20

OPERATION – MP3

"My MP3s"

Soft Rock

Song02

Hard RockSong01 Top 40

Song03

Song04

Song05

Song06

Song07

Song08

Song09

Song10

Song11

Classics

Speed Metal

LEVEL 2

LEVEL 1

LEVEL 3

ROOT

Directory01

Song02

Directory02Song01 Directory03

Song03

Song04

Song05

Song06

Song07

Song08

Song09

Song10

Song11

Directory05

Directory04

LEVEL 2

LEVEL 1

LEVEL 3

Any level

deeper than

LEVEL 3

will be

treated as

LEVEL 3

Any level

deeper than

LEVEL 3

will be

treated as

LEVEL 3

La page est en cours de chargement...

Rockford Fosgate RFX9420R Installation & Operation Manual

Ce manuel convient également à

Rockford Fosgate RFX9420R Installation & Operation Manual

dans d''autres langues

Documents connexes