Easypix SD III Manuel utilisateur

Preparing Your Camera

Getting Started

Digital Video Mode

Digital Camera Mode

Voice Recording Mode

Playback Mode

MP3 Mode

Camera Settings

TV Output

Copying Files to PC

Using PC Camera

Users Manual

MovieCam SD III

English

Safety Notice

1. Do not drop, puncture or disassemble the camera; otherwise the warranty will be voided.

2. Avoid all contact with water and dry hands before using.

3. Do not expose the camera to high temperature or leave it in direct sunlight. Doing so may

damage the camera.

4. Use the camera with care. Avoid pressing hard on the camera body.

5. For your own safety, avoid using the camera when there is a storm or lightning.

6. Avoid using batteries of different brands or types at the same time. There is potential of

explosion by doing that.

7. Remove batteries during long periods between usage, as deteriorated batteries may affect

the functionality of the camera.

8. Remove batteries if they show signs of leaking or distortion.

9. Use only the accessories supplied by the manufacturer.

10. Keep the camera out of the reach of children.

~ 1 ~

Welcome

Dear user, thanks for purchasing this product.

Much investment in time and effort has gone into its development,

and it is our hope that it will give you many years of trouble-free service.

~ 2 ~

Users guide

Camera

Driver CD

USB cable

AV cable

AA Alkaline

batteries x 4

Tripod

Bag

Wrist Strap

Earphone

Package Contents

Microphone

Back LED

Shutter/Record Button

Direction Buttons

OK Button

Menu Button

Wrist Strap Hook

SD/MMC Card Slot

Video-out Connector

USB Connector

Earphone Connector

Speaker

LCD Panel

LCD On/Off Detector

Flash Strobe

Lens

Lens Cover

Front LED

Battery Cover

Focus Switch

Power On/Off Button

Mode Switch

Tripod Socket

~ 3 ~

Camera Parts

Loading the batteries

Your camera runs on four AA alkaline batteries. High

performance batteries are recommended for this camera

for maximum battery life.

Preparing Your Camera

1. Slide the battery compartment

cover open in the direction as

indicated.

2. Place the batteries into the compartment. Note that

the positive and negative ends cannot be reversed.

3. After the batteries are properly

installed, replace the battery

compartment cover.

Preparing Your Camera

~ 4 ~

~ 5 ~

Inserting the SD/MMC card (optional)

The SD card comes with a write-protect switch. When the

write-protect switch is set to the Lock position, the card

will become non-writable. To ensure that the camera can

operate normally, you should set the write-protect switch

to the Unlock position before inserting the SD card.

In addition to 16MB (128Mbits) built-in flash memory, your

camera can store data on a Secure Digital (SD) card or a

MultiMedia card (MMC). The supported memory size

ranges from 8MB to 256MB.

To insert a SD/MMC card, gently push the card as

indicated until the card reaches the end of the slot. Note

that once a SD/MMC card is inserted, the camera will use

the card as the main storage media. Files stored in the

camera's built-in memory will become inaccessible until

the SD/MMC card is removed.

 To remove the SD/MMC card, gently push the card. After the

card pops up, pull the card out of the slot.

 Do not remove the SD/MMC card while the camera is

processing data (when the LED is flashing).

 If you insert a write-protected card, the media icon on the

LCD display will become red.

Unlock

Lock

Preparing Your Camera

Attaching the wrist strap

Please unfasten and separate the strap into two parts. To

attach the wrist strap to the camera, thread the strap

through the hook on the side of the camera, and then the

one on the bottom part. After threading the strap, fasten

the strap and then use the leather wrap to hold the strap.

~ 6 ~

How to hold your camera

Please put your hand through the wrist strap and firmly

hold the camera as illustrated. While taking stills or

recording AVI movies, avoid blocking the lens to retain

the best result.

Preparing Your Camera

Avoid blocking the lens.

Using the bag

The accessory bag comes handy if you are planning to

carry the camera with you while you are travelling around.

Simply put the camera into the bag as indicated, and you

are ready to carry the camera with you.

~ 7 ~

Using the tripod

Use a tripod to minimize camera movement and ensure

optimal image quality, especially while shooting self-

portraits or video conferencing.

Preparing Your Camera

 Avoid severe impact to the camera body even it is placed in

the bag.

Tight

Loose

Turning on your camera

Getting Started

Press and hold down the power button for 2 ~ 3 seconds

to turn on the camera.

 If the camera is not turned on after pressing the power

button, please check:

1. There are four AA batteries installed in the camera.

2. The batteries have enough power left.

 You can turn on the camera without opening the LCD panel.

 Please open the lens cover if you are going to use the digital

video or camera function.

Turning off your camera

Press and hold down the power button for 2 ~ 3 seconds

to turn off the camera.

Getting Started

The LED will light up.

The LED will go out.

~ 8 ~

Setting the date and time

When you power on the camera for the first time, you

need to set up the date and time:

1. Set the Mode Switch to Setting mode.

2. Press the Up or Down button

to highlight Date, and then

press the OK button or the

Right button to enter the

sub-menu.

Date

2003 / 01 / 01

3. Press the Left or Right button

to move the cursor. Press the

Up or Down button to change

the value. After the correct date

has been set up, press the OK

button to confirm the setting.

Time

12 : 00 : 00

4. Repeat step 2 and enter the

Time sub-menu. Use the same

method described in step 3 to

set time. Note that the second

digits are not adjustable. After

the correct time has been set up,

press the OK button to confirm

the setting.

Getting Started

Setting

Beep

ON

Boot-up

Auto Off

10m

Date

03/01/01

Tim e

12:00

 While operating the camera, pressing the Menu button can

bring up a sub-menu under most circumstances. The menu

items vary according to the mode you select. When a sub-

menu is being shown on the screen, you can use the

illustrated function buttons to make your selection.

Cancel

Move Cursor Up

Move Cursor Down

Cancel/Exit

Confirm

~ 9 ~

Tips for best shooting

Keep the focus set to except for close-ups.

Make sure your subject is well lit from the front.

Keep the camera level and steady when releasing the

shutter.

Make sure you have adequate light when taking stills

or recording AVI movies.

For stable and

smooth image

quality, move the

camera slowly

during filming.

The LCD display varies according to the operation mode.

However, you can easily check the media type and power

status on the LCD display.

Checking the media and power status

Getting Started

Storage media indicator:

: The camera is using the built-in memory for file

storage.

: The camera is using a SD card for file storage.

: The camera is using a MMC card for file storage.

Power status indicator:

: Full battery life.

: Adequate battery life.

: Low battery life.

: Empty battery life. Please replace the batteries

immediately when the icon is flashing red.

 When the camera is using a SD/MMC card as main storage

media, files stored in the camera's built-in memory will

become inaccessible until the card is removed.

 For details under different modes, please refer to the

respective chapters.

Make sure you have adequate light

~ 10 ~

The following chart is estimated based on a 64MB SD card. Actual capacity

may vary (up to +5%) depending on the environment and color condition.

Storage capacity chart

Getting Started

~ 11 ~

LCD display

Digital Video (DV) Mode

Digital Video Mode

Fine

1. 00 06:20

00:00

QVGA

DV mode indicator

Recording indicator

Recording time lapse

Image resolution

Image quality

Battery life indicator

Storage media type

Remaining capacity (mm:ss)

Zoom ratio

~ 12 ~

Recording an AVI movie

Digital Video Mode

1. Set the Mode Switch to Digital Video

mode.

2. Press the Shutter/Record button to start recording.

Shutter/Record button

4. Press the Shutter/Record button again to stop

recording.

3. While recording, you can press the Up or Down

button to zoom in/out the screen.

Second

Minute

Fine

1. 00 260

00:00

QVGA

Recording

indicator

 To review the recorded AVI movies, switch the camera to

Playback mode and play the AVI clips. Please refer to

Chapter 6 for more information.

~ 13 ~

Digital Video Mode

DV menu

While in Digital Video mode,

press the Menu button to bring

up the DV menu.

The following table illustrates all items and their functions.

DV

Video

VGA

Display

ON

Start/Stop Recording

Zoom In

Zoom Out

DV Menu

Function buttons

The following function buttons are available while the

camera is in Digital Video mode:

~ 14 ~

LCD display

Digital Camera Mode

Fine

2601. 00

EV+1

1280

Digital Camera mode indicator

Self-timer indicator

Flash indicator

White balance indicator

Image resolution

Image quality

Battery life indicator

Storage media type

Remaining capacity (pic.)

Exposure compensation value

Zoom ratio

~ 15 ~

Taking a still

1. Set the Mode Switch to Digital

Camera mode.

4. Press the Shutter/Record button to take a still.

3. Before shooting, you can press the Up or Down

button to adjust the zoom ratio.

2. Use the Focus Switch to set focus as appropriate.

12"~16" (30cm~40cm)

16"~ (40cm~ )

Shutter/Record button

~ 16 ~

Digital Camera Mode

Using the flash strobe

When the lighting is not sufficient for your shooting

environment, the flash can provide the extra light you

need.

Using the hot button

While in Digital Camera mode, pressing the Left button

allows you to switch the flash mode without entering the

options menu.

Pressing the hot button can cycle through three flash

modes - Auto, Force, Off.

Auto mode ( ): When the flash is set to Auto mode,

the camera will automatically measure the lighting

condition, and the flash will be activated if needed.

A

Force mode ( ): When the flash is set to Force

mode, the flash always fires no matter how the lighting

condition is.

Off (no icon): The flash will not function when it is set

to Off.

 When the battery power is low (with only one gauge left), the

flash strobe cannot be activated due to insufficient power for

recharge.

 While the flash is being recharged, you cannot press the

shutter button to take pictures.

~ 17 ~

Digital Camera Mode

Setting white balance

Under certain conditions, you may need to manually

select the white balance setting to take pictures with the

correct color balance.

Using the hot button

While in Digital Camera mode, pressing the Right button

allows you to change the white balance setting without

entering the options menu.

Pressing the hot button can cycle through five settings -

Auto, Sunny, Cloudy, Fluorescent, and Tungsten.

Auto (no icon): The camera will measure the color

temperature and make adjustments automatically.

Sunny ( ): Suitable for shooting outdoors in good

weather.

Cloudy ( ): Suitable for shooting under shades or

cloudy weather.

Fluorescent ( ): Suitable for shooting environment

with fluorescent light.

Tungsten ( ): Suitable for shooting environment

with incandescent light.

 White balance:

When the human eye sees an object, it adapts to the object

so that a white object always looks white. However, a digital

camera sees an object as white by adjusting the color

balance of the lighting condition. This process is called

matching the white balance.

~ 18 ~

Digital Camera Mode

Using the self-timer

1. While in Digital Camera mode, press the Menu button

to bring up the Camera menu.

2. Highlight the SelfTimer item,

and then select ON in the

sub-menu. Then press the

Menu button to exit.

2. Highlight the Exposure item,

and then select a desired EV

value in the sub-menu. The

larger the number is, the

brighter the stills will be.

3. When the Shutter/Record button is pressed, the

camera will have ten seconds delay before taking a

picture. After the shutter fires, the SelfTimer will be

automatically disabled.

10

Setting exposure compensation

Setting the EV value enables you to manually control the

brightness of the taken stills.

Camera

Strobe

AUTO

2M

ImageSize

SelfTimer

ON

DateSt amp

OFF

Display

OFF

1. Press the Menu button to bring up the Camera menu.

Highlight the Camera tab, and press the Right button

to select the Advanced tab.

Quality

Fine

0

Exposure

Advanced

WB

AUTO

 Setting the value too high may cause the pictures to appear

over-exposed.

~ 19 ~

Digital Camera Mode

La page charge ...

Easypix SD III Manuel utilisateur

Ce manuel convient également à

Easypix SD III Manuel utilisateur

dans d''autres langues

Autres documents