Brandt WFH1010K Le manuel du propriétaire

Marque: Brandt

Modèle: WFH1010K

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

Operating Instructions

Fully automatic washing machines

Mode d’emploi

Machines a laver entièrement

automatiques

Gebrauchsanweisung

Waschvollautomaten

δηγίες ρήσεως

για αυτµατα πλυντήρια ρύων

WFH 1010 K

List of Contents

Page

Safety and warning lights . . . . . . . . . 04

Installation . . . . . . . . . . . . . . . . . . . . 05

Transit bars . . . . . . . . . . . . . . . . . . 05

Alignment . . . . . . . . . . . . . . . . . . . 05

Building under . . . . . . . . . . . . . . . . 05

Connection . . . . . . . . . . . . . . . . . . . . 05

Water supply . . . . . . . . . . . . . . . . . 05

Water removal . . . . . . . . . . . . . . . . 05

Electrical connection . . . . . . . . . . . 06

Initial operation . . . . . . . . . . . . . . . . 06

Preparing to wash . . . . . . . . . . . . . . . 06

Colourfastness . . . . . . . . . . . . . . . . 07

Washing detergents which contain

solvents . . . . . . . . . . . . . . . . . . . . . 07

Dyeing/removing dye . . . . . . . . . . 07

Descaling . . . . . . . . . . . . . . . . . . . . 07

Woollens . . . . . . . . . . . . . . . . . . . . 07

Curtains . . . . . . . . . . . . . . . . . . . . . 07

Loading the machine . . . . . . . . . . . . 07

Washing detergents . . . . . . . . . . . . . 08

Choice of washing detergent and

amount required . . . . . . . . . . . . . . 08

Washing detergent dispensing

drawer . . . . . . . . . . . . . . . . . . . . . . 08

Washing detergent in powder form 08

Liquid washing detergent . . . . . . . . 08

Fabric conditioner . . . . . . . . . . . . . 08

Starch . . . . . . . . . . . . . . . . . . . . . . 08

Operating your washing machine . . . 09

Selecting a programme . . . . . . . . . 09

Temperature . . . . . . . . . . . . . . . . . 10

Additional functions . . . . . . . . . 10-11

Programme table . . . . . . . . . . . 12-13

End of programme . . . . . . . . . . . . . 14

Programme correction . . . . . . . . . . 14

Tips for caring for your laundry and

the environment . . . . . . . . . . . . . . . . 14

Care and maintenance . . . . . . . . . . . 15

Washing detergent dispensing

drawer . . . . . . . . . . . . . . . . . . . . . . 15

The suds pump . . . . . . . . . . . . . . . 15

The strainer in the water

connection hose . . . . . . . . . . . . . . 15

Washing drum and rubber collar . . 15

Housing, washing machine door

and plastic parts . . . . . . . . . . . . . . 15

Help if a fault occurs . . . . . . . . . . . . . 16

Customer service . . . . . . . . . . . . . . . 17

Please read first!

Dear customer,

By buying this appliance, offering you a

load of 1 to 6 kg, you have made a deci-

sion for up-to-date washing technology –

premium quality, long service life, highly

reliable and optimal operating conven-

ience.

• At first please check if the applicance

was received undamaged.

• If atransportdamage is noticed please

inform your dealer immediately, and

do not operate the appliance!

These Operating Instructions...

...are intended to help you operate this

appliance quickly and safely.

• Read the Operating Instructions – be-

fore installation and initial operating

of this appliance.

• Pay special attention to the safety-

informations.

• Keep these Operating Instructions for

future reference.

• If you sell the appliance pass on the

instructions to the new owner.

Safety and warning lights

Your washing machine is suitable for

washing textiles which have been labelled

as machine washable by the manufactur-

er. Using this washing machine for other

purposes could be dangerous. Do not use

solvents in this washing machine (there

could be a risk of fire or explosion).

Please read the instructions given below

and follow them carefully. Failure to do

so will invalidate the guarantee.

• Please ensure that the packaging mate-

rial is disposed of in accordance with

the current environmental require-

ments.

• If the washing machine is visibly dam-

aged, do not connect it. Contact your

supplier.

• The washing machine must be installed

in a room which is not susceptible to

frost. Frost will cause damage to the

hoses (they may split or burst) and may

cause the electric and electronic compo-

nents to malfunction.

• Before use, check that the transit bars

have been removed. Failure to remove

the transit bars before operation could

damage the washing machine and other

adjacent fixtures.

• Make sure that the inlet and outlet

hoses are fitted in accordance with the

instructions. Improper connection can

lead to flooding.

Cracks or kinks in the hoses may in time

cause them to leak. Check the condition

of the hoses at regular intervals to pre-

vent water damage occurring.

• If the washing machine is installed on a

plinth, for safety reasons two restrainers

must be fitted under the two front feet.

• The washing machine must only be

used as directed in the operating in-

structions in order to prevent damage

to the laundry and to the washing

machine. The washing machine must

only be used for washing and spinning

household laundry. Use only detergents

and conditioners which are suitable for

use in household washing machines.

The washing machine door will become

hot when laundry is washed at high

temperatures.

Do not reach into the drum when it is

turning and do not touch the washing

machine with wet hands.

Do not allow children to play with the

washing machine and keep household

pets away from it.

• Take care to ensure that objects (such

as coins, screws, nails, paper clips, etc.)

are removed from all clothing before it

is loaded into the washing machine;

these objects could damage the suds

sump and the drum.

• If the washing machine fails to function

properly and you cannot rectify the

fault using the information in the manu-

al, disconnect the washing machine

from the electricity supply, switch off

the water and contact the customer ser-

vice department (see page 16).

• All our electrical appliances comply with

the relevant safety regulations. Repairs

to electrical appliances must only be

carried out by a qualified electrician.

Repairs carried out by anyone else could

endanger the user considerably. Make

sure that only original spare parts are

used, in order to prevent further dam-

age from occurring.

• When the washing machine becomes

obsolete, ensure that it can no longer

be used. First remove the mains plug

from the wall socket, then cut the con-

nection cable. Switch off the water sup-

ply and remove the inlet hose. Ensure

that the door lock is inactivated.

Installation

Transit bars

Before the washing machine is operated,

the transit bars at the reverse of the wash-

ing machine must be removed . The

three screws must be removed together

with the distance sleeves. Using a span-

ner (SW 13), loosen the three screws and

pull them and their distance sleeves

through the side holes .

Store these parts in a safe place as they

will be required if the washing machine is

to be transported again in the future

(e.g. if you move house).

The holes where the screws have been

can be concealed using the plastic caps

supplied.

Alignment

The washing machine must be placed on

a surface which is level and stable. A

slightly uneven surface can be compen-

sated for by adjusting the four feet of the

washing machine . To adjust, loosen the

locking nuts using an SW17 flat key, align

the washing machine feet and tighten the

locking nuts again. Check that the

machine is level and stable (use a spirit

level).

After positioning of tha appliance the

mains connection (plug) must always be

accessible.

The washing machine must not be placed

on a long-pile carpet.

Building under

This washing machine can be built under

a continuous kitchen counter. The cover

sheet required for this purpose can be

obtained from the customer service

department.

Connection

Water supply

This washing machine can be connected

to any water supply without a non-return

valve. In oder to do so, the inlet hose

must be screwed onto a tap with a

⁄4”

inch B.S.P. thread ,. The water

pressure should be 10 - 100 N/cm

(1 - 10 bar).

If the water pressure is higher than this, a

pressure-reducing valve must be connect-

ed in series. The angled end of the inlet

hose must be screwed onto the water

connection support on the rear of the

washing machine.

Turn on the water tap (at full water pres-

sure) and check that the connection point

on the tap and on the washing machine is

watertight. If necessary, adjust the fit of

the seal and screw connection. Advice on

how to extend the length of the hose can

be obtained from the customer service

department.

Water removal

The water which is pumped away must be

able to flow away freely. In order to allow

this, there must be no bends in the hose

and the end of the hose must be fitted no

higher than 100 cm above the floor level.

It is possible to connect it to a syphon. If

the water is to drain into a wash basin/

sink, the outlet hose must be fitted using

the hose holder supplied  (pull the hose

holder to the end of the hose) to prevent

it from falling down and to ensure that

the end of the hose does not go below

the level of the water which is being

pumped off . (For example, on the loop

of the hose holder).

 For the case that the drain hose should

be connected to a siphon, the enclosed

rubber hose middle part has to be fixed

between the drain hose and the siphon

and secured by two hose clamps. If not,

there is the danger of flooding! The hose

clamps can be bought in a specialist shop.

Electrical connection

In order to make the electrical connection

a Home Office socket is required. If the

machine is to be connected permanently,

a mains switch with a minimum contact

clearance of 3 mm is required. The electri-

cal connection must be made in accord-

ance with the national regulations and

any additional regulations set by the

energy supplying company. The fuse pro-

tection and the type of machine are

stated on the wasching machine plate on

the rear of the washing machine . The

washing machine must not be switched

on before the electrical connection has

been made.

Warning!! The power supply cord must

only be replaced by an authorised

specialist or a qualified person.

After installation of the machine the

mains plug has to be accessible.

Initial operation

It is advisable to run the first washing

cycle without any laundry in the machine

in order to rinse out any remaining test

water. For this purpose select the

coloured cottons 60° short programme

(see programme table) and put a little

washing detergent in compartment II

(centre) of the detergent dispensing

drawer.

Preparing to wash

Try where possible to wash garments of

the same type in one wash.

Sort the laundry according to care sym-

bols (see table), degree of soiling and

weight.

Remove all objects from folds or pockets

in garments and close zip fasteners. Gar-

ments which contain wire (ladies under-

wear, for example) should be tied in a

material bag in order to ensure that the

wires do not work loose and slip in be-

tween the drum and the outer tub.

Objects such as hair clips, paper clips,

coins, screws, needles, etc. can damage

the washing machine .

Heavily soiled areas and stains which are

water soluble should be treated appropri-

ately before washing. In problem cases

advice should be sought from a specialist

(chemist, dry cleaner).

International care symbols

White and coloured cottons

Easy-care fabrics and delicates:

Woollens:

Hand wash Do not wash

Colourfastness

Ascertain whether new garments are

colourfast before washing. If in doubt,

wash new coloured cottons separately.

Washing solutions which contain

solvents

Garments which have been pre-treated

with such solutions must not be washed

in your automatic washing machine or

they could damage the machine compo-

nents and poisonous gases could be given

off (giving rise to a danger of fire and ex-

plosion).

Textiles which have been pre-treated must

be rinsed out in clear water before they

are washed in the machine.

Dying/ removing dye

Use only appropriate dyes and dye remov-

ing agents. Follow the manufacturer's in-

structions.

Ocean will not accept liability for any

damage which arises as a result of dying/

dye removal.

Woollens

Woollen items which carry the textile care

label " with special facility will not felt"

or " machine washable on super wash"

or ” handwash” can be washed in this

washing machine without any problem.

Curtains

Remove lead tape which is not sewn into

the curtains and all hooks.

Loading the machine

To open the door of the washing

machine, press the appropriate button.

Unfold the laundry and place it loosely in

the drum. The max. load depends on the

laundry type, the grade of soil, and the

wash programme (max. 6 kg slightly

soiled laundry with the cottons pro-

grammes).

When the laundry has been loaded into

the machine, close the door and you will

hear the door lock engage.

After the machine has been switched on

the door will remain locked for the dura-

tion of the programme. The indicator

lamp will light up. The water level in the

drum must be checked before the wash-

ing machine door is opened. If necessary

(as in the case of all programmes which

end in a rinse stop) the programme selec-

tor must be set to pump so that the water

can be pumped off. After this the door

can be opened.

Washing solution

Choice of washing solution and amount

required

Only use automatic washing detergents.

The type of detergent used depends on

the washing temperature, as well as on

the colour and type of textile. Follow the

detergent manufacturer's instructions.

The amount of detergent required de-

pends on the degree of soiling, the quan-

tity of laundry and the level of water

hardness.

Ask your local water authority about the

level of water hardness in your area.

Water hardness levels

123 4

soft medium hard very hard

up to 1,3 1,3 - 2,5 2,5 - 3,8 over 3,8

mmol/l mmol/l mmol/l mmol/l

(used to be (used to be (used to be (used to be

7° dH) 7 - 14° dH) 14 - 21°dH) over 21° dH)

Too much washing detergent can cause

excessive quantities of foam and could

have an adverse effect on the washing

and rinsing process. Insufficient washing

detergent can result in damaging lime

deposits and may make the laundry look

grey. In order to prevent this, it is advis-

able to first place the washing detergent

in the detergent dispensing drawer and

then the softening agent.

Washing detergent dispensing drawer

The washing detergent should be mea-

sured and placed in the appropriate com-

partment or compartments of the deter-

gent dispensing drawer before the

washing programme commences.

In order to do this, pull open the deter-

gent dispensing drawer .

The drawer is made up of 3 compart-

ments:

Compartment I for pre-wash

or starching (left)

Compartment II for the main

washing cycle (centre)

Compartment III for fabric conditioner

or starch (right)

Washing detergent in powder form

To be used in compartment II.

Liquid detergent

When using liquid or gel-like detergents,

please note the following:

• Use the detergent maker’s proportion-

ing cup and observe the information

given on the packing.

Fabric conditioner

Use the appropriate quantity of fabric

conditioner as stated by the manufact-

urer.

If the conditioner is very thick, it is advis-

able to dilute it with water before use in

order to ensure that it is dispensed com-

pletely into the washing machine. The

red upper edge in compartment III indi-

cates the maximum filling level. At the

end of the washing programme a small

amount of water will remain in the fabric

conditioner compartment of the drawer.

Starch

a) Finishing agent and liquid starch:

Use as you would fabric conditioner

(compartment III)

b) Starch in powder form:

The starch should be prepared and

used as indicated by the manufacturer;

place in compartment I.

Operating your washing

machine

Select the washing programme from the

programme table (note care symbols in

the garments). First set the programme

selector to the required washing pro-

gramme and, if necessary, select any addi-

tional functions. Following this set the re-

quired temperature. Press the On/OFF

button and the light will come on to

show that the machine ist working. The

door is now locked.

Selecting a programme

There are four main programmes:

Cottons

Easy-care

Delicates

Woollens

Each programme comprises a complete

washing process, including wash, rinse

and spin.

Note that the programme selector con-

trol should only be turned in a clockwise

direction. Failure to do so may damage

the machine.

Cottons: (white/coloured)

Pre-wash

Intensive

Normal

Quick

Cold

Easy-care fabrics:

Intensiv

Normal

Quick

Cold

Delicates:

Delicates

Woollens

Hand wash

If you only want to starch your laundry or

to give it a conditioning rinse, select the

setting .

If you only want to spin your laundry,

select setting .

Stop

Quick

intensive

Stop

Quick

intensive

Temperature

The temperature can be selected freely

using the temperature selector. In order

to prevent your laundry from being dam-

aged if you make a mistake in setting the

temperature, the temperature has been

restricted automatically to 60 °C in the

easy-care programme and to 40 °C in the

delicates and woollens programmes.

Additional functions

If one or more additional functions are

selected, the washing programme can be

tailored to your individual needs.

Extra rinsing button

If the extra rinsing button is pressed, an

extra rinse cycle will be included. This is

advisable for people with sensitive skins.

This function can be selected in the

cottons and easy-care programmes.

Intensive

The Intensive button has the effect of pro-

longing the washing time, so that a better

washing result can be obtained at a lower

temperature. For example, you could

wash a moderately soiled white wash at

60°C instead of at 95°C if you press the

Intensive button. This will enable you to

save 25-35% on electricity costs. This

function can be selected with the

white/coloured cottons and easy-care

washing programmes. Please note that if

the button is pressed, the temperature in

the whites/coloured cottons is automati-

cally limited to 60 °C and in the easy-care

programmes it is limited to 40 °C.

Rinse hold

If you press the rinse hold button the

washing machine will not spin the laun-

dry. The programme stops at the last

rinsing cycle, the laundry remains in the

water. This function can be selected with

the easy-care, delicates and woollens pro-

grammes. The programme can be contin-

ued in either of the following ways:

1. Cancel the rinse stop button: the pro-

gramme sequence will then automati-

cally move into the spin section.

30˚

40˚

50˚

60˚

70˚

80˚

95˚

30˚

40˚

50˚

60˚

70˚

80˚

95˚

1000

600

IntensiveIntensive

1000

600

2. Switch off the machine, set the pro-

gramme selector to the position

”pump” and switch on the machine

again.

Short programme

If the short button is pressed, the main

washing cycle is shortened and the num-

ber of rinsing cycles is reduced. Select the

‘short’ function either for laundry that is

only lightly soiled or for small quantities

of laundry. This function can be selected

in the whites/coloured cottons and the

easy-care programmes.

Spin reduction

This button can be used to reduce the

maximum spin speed to 600 rpm. The

greater the spin speed, the less residual

moisture will remain in the laundry. If you

intend to dry the laundry in a tumble dry-

er, select the maximum possible spin

speed on your washing machine in order

to save energy when tumble drying.

In the easy-care and woollens pro-

grammes the maximum spin speed is lim-

ited to 800 rpm in order to protect the

laundry and in the delicates programme it

is limited to 650 rpm.

If the washing machine fails to spin the

laundry even though you have not

pressed the ‘rinse stop’ button, it is possi-

ble that the Automatic Spin Correction

System (ASC) has stopped the machine

from spinning. In that case, the laundry

will have caused such an imbalance in the

washing machine that the spin has been

abandoned in order to prevent the

machine from becoming unstable.

1000

600

1000

600

Programme table

Care symbol Programme selector Temper. selector Addit. function

Cottons: white/coloured

(Quantity of laundry – max. 6 kg)

Intensive 90 °C Extra rinsing

(with) Prewash 30 - 90 °C Extra rinsing

Normal 40 - 60 °C Intensive

Quick - lightly soiled 30 - 40 °C Short programme

cold I Rinse hold

Easy-care fabrics

(Quantity of laundry – 2 kg)

Intensiv 60 °C Extra rinsing

Normal 40 °C Intensive

Quick - lightly soiled 30 °C Short programme

cold I Rinse hold

Delicates

(Quantity of laundry – 2 kg)

Delicates I - 40 °C Rinse hold

Curtains I - 30 °C

Woollens

(Quantity of laundry – 1 kg)

Woollens (handwash) I Rinse hold

Woollens I - 40 °C

Conditioning rinse

(Quantity of laundry – 1 - max. 6 kg)

Cond. rinse - cotton I Rinse hold

Cond. rinse - easy care

Cond. rinse - delicate /

woollens

Spin

(Quantity of laundry - 1 - max. 6 kg)

Spin - cotton I Spin reduction

Spin - easy care

Spin - delicate /

woollens

Pump I

1000

600

1000

600

Programmes Temperature Capacity Water Energie Duration

(°C) max. (kg)

(l) (kWh) (min.)

White cottons 90 6 62 1,78 141

Coloured cottons

60 6 58 1,10 125

Coloured cottons 40 6 58 0,55 105

Easy-care fabrics 40 2 45 0,38 74

Delicates 30 2 58 0,17 40

Woollens 30 1 55 0,14 41

Measured values for load capacity 5.0 kg.

Test programme in accordance to EN 60456.

End of programme

After end of programme the indication

”door lock” goes out. Then you can open

the door and take out the laundry. You

switch off the appliance by pressing the

button ”ON/OFF “. Turn off the water-

tap and let the inside of the washing-

machine dry by leaving the door open.

Programme correction

If a change of programme is necessary,

switch off the appliance first. Set the pro-

gramme selector switch to the position

”pump” and let the programme finish.

Afterwards select the new programme

and switch on the machine again (you

may have to refill some washing-powder).

If you move the programme selector

switch by hand during operation a normal

course of the programme is no longer

guaranteed.

Tips for caring for your laun-

dry and the environment

You can contribute to the protection of

the environment by bearing the following

advice in mind:

• Wash the maximum load (see pro-

gramme table)

• Save energy by washing at reduced

temperatures and using the Intensive

button with the white/coloured cottons

and easy-care programmes.

• Where appropriate, wash particulary

heavily soiled laundry separately.

• Use less washing detergent for smaller

loads and laundry which is only lightly

soiled and select the short programme.

Care and Maintenance

Washing detergent dispensing drawer

To wash the washing detergent dispens-

ing drawer, pull it out as far as possible

and then with a short, sharp pull remove

it completely . To enable the washing

machine to function properly, the fabric

conditioner syphon and the dispensing

compartments should be washed under

warm running water. In order to do this,

remove the syphon  and if necessary

free the opening using a needle. From

time to time the injection nozzles which

are situated above the dispensing com-

partments should be cleaned using a

brush, for example.

The drain pump

The drain pump only needs to be cleaned

if it becomes blocked with buttons, paper

clips, etc. The remaining water in the

washing machine must be pumped off

beforehand.

Note: Allow hot suds to cool first.

First remove the mains plug from the wall

socket. Unlock the maintenance flap by

pressing the side opening button and lift-

ing it up . Fold down the run-off flap

and place a flat bowl under it . Turn the

pump cover a quarter turn to the left 

and allow the water to run off. When the

bowl is full, turn the pump cover to close

it. Repeat this procedure until no more

water comes out.

Unscrew the pump cover completely 

uand remove the unwanted objects.

Clean the housing and the pump wings.

Screw the pump cover closed again and

close the run off and maintenance flap.

Outer tub and sump

At temperatures below 0 °C the washing

machine must be emptied completely.

Proceed as if cleaning the drain pump.

Damage due to frost will not be covered

by the guarantee.

The strainer in the water connection

hoses

The strainer in the water connection

hoses (at the rear of the machine) should

be cleaned from time to time. To do this,

the water tap must be turned off.

Machine types without Aqua-stop hose:

The strainer is situated in the screw con-

nection on the machine. To clean the

strainer, unscrew the hose from the rear

of the washing machine. Using a pointed

pliers, pull out the strainer by the edge,

clean it and put it back .

When putting the hose back onto the tap,

make sure that the strainer and the seal fit

correctly.

Washing drum and rubber collar

If any items made of metal (paper clips,

etc) are allowed to remain in the moist

drum or in the rubber seal ring, they may

cause rust marks.

In such a case, the drum should be

cleaned using a stainless steel cleaning

agent. Never use steel wool!

Unwanted objects (paper clips, etc) must

be removed from the fold of the rubber

seal .

Housing, washing machine door and

plastic parts

Clean using soapy water, mild cleaning

agents, or other agents commonly used

for cleaning plastics. Do not use abrasive

agents!

Dry using a soft cloth.

Help if a fault occurs

However, you will be able to remedy

minor faults and malfunctions yourself.

Before contacting the customer service

department, please check the following

points:

If the machine will not work

• Check the fuse in your house

• Check that the mains plug is inserted

correctly into the wall socket

If the drum does not fill up with water

• Check whether the door is properly

closed

• Check that the water taps are turned on

• The water pressure in the water supply

network is perhaps too low. Check the

water pressure.

• There might be something obstructing

the inlet hose. Check that the hose is

not bent or twisted.

• The strainer in the water connection

hose may be blocked. Remove any for-

eign bodies or waste from it.

If the water stays in the washing

machine

• You may have pressed the rinse stop

button. Press the button again to re-

lease it or set the programme selection

switch to 'pump', 'spin' or 'short spin'.

• Is there something obstructing the out-

let hose?

• The drain pump might be blocked.

Make sure that there is no waste in it.

If the washing machine is not very

stable

• Check that the transit bars have been

removed. Check that the screws and

their distance sleeves have been re-

moved from the rear of the washing

machine.

• Check that the machine has been posi-

tioned properly

• Is there something obstructing the

outlet hose?

If the washing machine leaks

• Check that the inlet and outlet hoses

have been properly fitted.

• Check that the cover on the drain pump

has been screwed down properly.

• Note whether the washing machine

foams too much during the washing cy-

cle and the whether foam comes out of

the detergent dispensing drawer.

If the washing detergent foams too

much

• The ratio of washing detergent to laun-

dry is not right. Reduce the amount of

washing detergent you are using.

• The level of water hardness could be

very low. Ask your local water authority

what your local water hardness level is

and reduce the amount of washing de-

tergent accordingly.

• The formation of foam in the final rins-

ing cycle or during the final spin can be

due to the washing detergent. This

does not however make the rinse less

effective.

If the laundry is still too wet after it has

been washed

• The spin speed you have selected is too

slow.

• You have selected a basic programme

which limits the spin speed automati-

cally.

• The Automatic Spin Correction System

has reduced the spin speed or stopped

the spin because of an imbalance. An

imbalance can arise as a result of only a

few large items of laundry being washed

together. For this reason it is advisable

to wash a combination of large and

small items together in the drum.

If the laundry is not completely clean

• Grey marks on textiles which were

soiled with ointments, fat or oil can re-

main if insufficient washing detergent is

used. Increase the quantity of washing

detergent you use.

• White marks are caused by the insoluble

water softening components of modern

phosphate-free washing detergents.

Remove them from the laundry by shak-

ing or brushing the garments or, alter-

natively, use liquid washing detergent.

If you are unable to remedy the fault

yourself, contact the customer service

department and quote the model code

and identification number which is

stamped into the machine plate. Our cen-

tral customer service department will be

pleased to advise you which customer

service technician covers your area.

Sommaire

Page

Conseils de sécurité et de prudence 20

Installation de l’appareil . . . . . . . . . 21

Sécurité de transport . . . . . . . . . . . 21

Mise à niveau . . . . . . . . . . . . . . . . 21

Encastrement . . . . . . . . . . . . . . . . 21

Branchement . . . . . . . . . . . . . . . . . . 21

Arrivée d’eau . . . . . . . . . . . . . . . . . 21

Evacuation d’eau . . . . . . . . . . . . . . 21

Raccordement électrique . . . . . . . . 22

Première mise en service . . . . . . . . 22

Préparation de lavage . . . . . . . . . . . 22

Solidité des couleurs . . . . . . . . . . . 23

Détergents contenant des

dissolvants . . . . . . . . . . . . . . . . . . . 23

Coloration / Décoloration . . . . . . . 23

Détartrage . . . . . . . . . . . . . . . . . . . 23

Laine . . . . . . . . . . . . . . . . . . . . . . . 23

Rideaux . . . . . . . . . . . . . . . . . . . . . 23

Chargement . . . . . . . . . . . . . . . . . . 23

Produits de lessive . . . . . . . . . . . . . 24

Utilisation de l’appareil . . . . . . . . . . 25

Choix du programme . . . . . . . . . . 25

Température . . . . . . . . . . . . . . . . . 26

Fonctions supplémentaires . . . . 26-27

Tableau des programmes . . . . . 28-29

Fin du programme . . . . . . . . . . . . . 30

Modification du programme . . . . . 30

Conseils pour l’entretien du linge

respectueux de l’environnement . . 30

Entretien et maintenance . . . . . . . . 31

Bac à produits lessiviels . . . . . . . . . 31

Pompe de vidange . . . . . . . . . . . . . 31

Cuve . . . . . . . . . . . . . . . . . . . . . . . 31

Filtre du raccordement d’eau . . . . . 31

Tambour et soufflet d’étanchéité

en caoutchouc . . . . . . . . . . . . . . . . 31

Carter, hublot et pièces en matière

plastique . . . . . . . . . . . . . . . . . . . . 31

Conseils en cas de pannes . . . . . 32-33

A lire en premier!

Chère cliente,

cher client,

Avec l’achat de cette machine, qui vous

offre une capacité de lavage de 1 à 6 kg,

vous avez opté pour une technologie de

lavage des plus modernes – une qualité

supérieure, une longévité élevée, une

grande sécurité de fonctionnement et un

confort d’utilisation optimal.

• Veuillez vérifier en premier lieu que

l’appareil n’a pas été endommagé

pendant le transport.

• Si vous constatez des dommages dus

au transport, veuillez vous adresser

aussitôt à votre revendeur ou votre

point de vente. Ne mettez pas la ma-

chine en service!

Cette notice d’utilisation...

...doit vous permettre d’utiliser la machine

rapidement et en sécurité.

• Lisez cette notice – avant d’installer la

machine et de la mettre en marche.

• Observez en particulier les consignes

de sécurité.

• Conservez la notice d’utilisation afin

de pouvoir la consulter ultérieure-

ment.

• Remettez-la également aux autres uti-

lisateurs éventuels.

Conseils de sécurité et de prudence

Votre appareil est destiné au lavage de

textiles que le fabricant a étiquetés

„lavable en machine“. D’autres applica-

tions pourraient s’avérer dangereuses.

N’utilisez pas de produits solvants dans

l’appareil (danger d’incendie et

d’explosion).

Veuillez absolument respecter les conseils

suivants, faute de quoi nous déclinons

toute responsabilité:

• Recycler les diverses pièces de l’emballa-

ge conformément aux prescriptions en

cours pour la protection de l’environne-

ment.

• En cas de dommages visibles ne pas

brancher l’appareil. Dans ce cas appeler

immédiatement le fournisseur.

• Ne pas installer le lave-linge dans une

pièce exposée au gel. Les effets du gel

endommagent les tuyaux (ils se fissurent

ou éclatent) et altèrent le bon fonction-

nement des composants électriques et

électroniques.

• Avant la première mise en service,

contrôler que le blocage de transport a

bien été enlevé. En cas d’omission, le

blocage de transport endommagerait

l’appareil et les meubles avoisinants.

• Vérifier que les tuyaux d’arrivée et

d’évacuation d’eau sont bien fixés selon

les instructions de branchement.

Une négligence provoquerait des

inondations.

En cas de fissure, de pliure ou autres, les

tuyaux peuvent fuir au cours du temps.

Les contrôler régulièrement pour éviter

des dégâts des eaux.

• En cas d’installation sur un socle il est

conseillé, pour des raisons de sécurité,

de prévoir 2 logements de fixation pour

les pieds avant de l’appareil.

• L’appareil ne doit être utilisé qu’en fonc-

tion des recommandations du mode

d’emploi pour éviter tout endommage-

ment du linge et de la machine.

L’appareil ne doit servir qu’au lavage et

à l’essorage de linge de maison. N’utili-

sez que des produits de lavage et d’en-

tretien spécifiquement prévus pour

l’emploi dans des lave-linge domes-

tiques.

En cas de lavage à haute température, le

hublot devient très chaud.

Evitez tout accès au tambour pendant sa

rotation et ne touchez pas à l’appareil

avec des mains humides.

Ne laissez pas les enfants jouer avec

l’appareil et éloignez-en les animaux

domestiques.

• Retirez tous les corps étrangers (par ex.

pièces de monnaie, vis, clous, trom-

bones, etc...) qui pourraient se trouver

dans le linge avant de le placer dans la

machine, car ils pourraient endomma-

ger la cuve et le tambour.

• S’il vous est impossible de remédier

vous-même aux dysfonctionnements en

suivant les informations du mode d’em-

ploi, débranchez l’appareil (en ne tirant

pas sur le câble, mais sur la prise) ou le

fusible correspondant. Fermez le robinet

d’arrivée d’eau et appelez le SAV.

• Les appareils électro-ménagers répon-

dent aux normes de sécurité respectives.

Les réparations ne doivent être faites

que par des professionnels. Toute répa-

ration qui ne serait pas effectuée par un

professionnel peut être dangereuse pour

l’utilisateur et ne bénéficie pas de la ga-

rantie.Veillez à n’utiliser que des pièces

détachées d’origine constructeur pour

éviter tout dommage consécutif.

• Les appareils usagés sont à mettre im-

médiatement hors-service. Retirer la pri-

se de courant, couper le câble d’alimen-

tation et le jeter avec la prise. Fermer le

robinet d’arrivée d’eau et retirer le tuyau

d’arrivée d’eau. Détruire la serrure du

hublot de l’appareil

La page charge ...

Brandt WFH1010K Le manuel du propriétaire

Marque: Brandt

Modèle: WFH1010K

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Brandt WFH1010K Owner's manual

Brandt WFH1010K Le manuel du propriétaire

Brandt WFH1010K Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents