Multitech MTQN-MNG1-B01.R1 Mode d'emploi

Catégorie
La mise en réseau
Taper
Mode d'emploi

Ce manuel convient également à

Dragonfly
Nano
MTQN-MNG1-B01 Device Guide
DRAGONFLYTM NANO DEVICE GUIDE
2 Dragonfly
Nano MTQN-MNG1-B01 Device Guide
Dragonfly
TM
Nano Device Guide
Models: MTQN-MNG1-B01
Part Number: S000671 rev 1.5
Copyright
This publication may not be reproduced, in whole or in part, without the specific and express prior written permission signed by an executive officer of
Multi-Tech Systems, Inc. All rights reserved. Copyright © 2019 by Multi-Tech Systems, Inc.
Multi-Tech Systems, Inc. makes no representations or warranties, whether express, implied or by estoppels, with respect to the content, information,
material and recommendations herein and specifically disclaims any implied warranties of merchantability, fitness for any particular purpose and non-
infringement.
Multi-Tech Systems, Inc. reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of
Multi-Tech Systems, Inc. to notify any person or organization of such revisions or changes.
Trademarks and Registered Trademarks
MultiTech, and the MultiTech logo, MultiConnect, and Dragonfly are trademarks or registered trademarks of Multi-Tech Systems, Inc. All other products
and technologies are the trademarks or registered trademarks of their respective holders.
Legal Notices
The MultiTech products are not designed, manufactured or intended for use, and should not be used, or sold or re-sold for use, in connection with
applications requiring fail-safe performance or in applications where the failure of the products would reasonably be expected to result in personal injury or
death, significant property damage, or serious physical or environmental damage. Examples of such use include life support machines or other life
preserving medical devices or systems, air traffic control or aircraft navigation or communications systems, control equipment for nuclear facilities, or
missile, nuclear, biological or chemical weapons or other military applications (“Restricted Applications”). Use of the products in such Restricted
Applications is at the user’s sole risk and liability.
MULTITECH DOES NOT WARRANT THAT THE TRANSMISSION OF DATA BY A PRODUCT OVER A CELLULAR COMMUNICATIONS NETWORK WILL BE
UNINTERRUPTED, TIMELY, SECURE OR ERROR FREE, NOR DOES MULTITECH WARRANT ANY CONNECTION OR ACCESSIBILITY TO ANY CELLULAR
COMMUNICATIONS NETWORK. MULTITECH WILL HAVE NO LIABILITY FOR ANY LOSSES, DAMAGES, OBLIGATIONS, PENALTIES, DEFICIENCIES, LIABILITIES,
COSTS OR EXPENSES (INCLUDING WITHOUT LIMITATION REASONABLE ATTORNEYS FEES) RELATED TO TEMPORARY INABILITY TO ACCESS A CELLULAR
COMMUNICATIONS NETWORK USING THE PRODUCTS.
The MultiTech products and the final application of the MultiTech products should be thoroughly tested to ensure the functionality of the MultiTech
products as used in the final application. The designer, manufacturer and reseller has the sole responsibility of ensuring that any end user product into
which the MultiTech product is integrated operates as intended and meets its requirements or the requirements of its direct or indirect customers.
MultiTech has no responsibility whatsoever for the integration, configuration, testing, validation, verification, installation, upgrade, support or maintenance
of such end user product, or for any liabilities, damages, costs or expenses associated therewith, except to the extent agreed upon in a signed written
document. To the extent MultiTech provides any comments or suggested changes related to the application of its products, such comments or suggested
changes is performed only as a courtesy and without any representation or warranty whatsoever.
Contacting MultiTech
Knowledge Base
The Knowledge Base provides immediate access to support information and resolutions for all MultiTech products. Visit http://www.multitech.com/kb.go.
Support Portal
To create an account and submit a support case directly to our technical support team, visit: https://support.multitech.com.
Support
Business Hours: M-F, 8am to 5pm CT
Country By Email By Phone
Europe, Middle East, Africa: [email protected] +(44) 118 959 7774
U.S., Canada, all others: [email protected] (800) 972-2439 or (763) 717-5863
Warranty
To read the warranty statement for your product, visit www.multitech.com/warranty.go. For other warranty options, visit www.multitech.com/es.go.
World Headquarters
Multi-Tech Systems, Inc.
2205 Woodale Drive, Mounds View, MN 55112
Phone: (800) 328-9717 or (763) 785-3500
Fax (763) 785-9874
CONTENTS
Dragonfly
Nano MTQN-MNG1-B01 Device Guide 3
Contents
Chapter 1 Product Overview ................................................................................................................................. 6
Overview ....................................................................................................................................................................... 6
Documentation ............................................................................................................................................................. 6
Product Build Options................................................................................................................................................... 6
Chapter 2 Mechanical Drawings............................................................................................................................ 7
MTQN-MNG1-B01......................................................................................................................................................... 7
Chapter 3 Hardware and Specifications................................................................................................................. 8
Specifications ................................................................................................................................................................ 8
Mounting Hardware...................................................................................................................................................... 9
Recommended Parts................................................................................................................................................... 9
40-Pin Connector Definitions........................................................................................................................................ 9
MTQN-MNG1-B01 Pin Definitions ............................................................................................................................ 10
40-Pin Connector ........................................................................................................................................................ 17
Communications Flow................................................................................................................................................. 17
MTQN-MNG1-B01..................................................................................................................................................... 17
Electrical Characteristics ............................................................................................................................................. 18
Operating Conditions ................................................................................................................................................ 18
Absolute Maximum Ratings ...................................................................................................................................... 18
Nominal Ratings ........................................................................................................................................................ 19
Power Draw................................................................................................................................................................. 20
USB Cable Recommendations .................................................................................................................................... 20
Device Reset................................................................................................................................................................ 21
MTQN-MNG1-B01..................................................................................................................................................... 21
Powering Down the Cellular Radio ............................................................................................................................. 21
Low Power Modes....................................................................................................................................................... 21
Installing a SIM Card ................................................................................................................................................... 22
Configuring u-blox Cellular Radio................................................................................................................................ 22
USB Driver Installation .............................................................................................................................................. 24
Chapter 4 Antennas ............................................................................................................................................ 25
Antenna....................................................................................................................................................................... 25
Antenna Specifications ............................................................................................................................................. 25
Chapter 5 Safety Information.............................................................................................................................. 26
Handling Precautions .................................................................................................................................................. 26
Radio Frequency (RF) Safety ..................................................................................................................................... 26
General Safety........................................................................................................................................................... 27
Interference with Pacemakers and Other Medical Devices ..................................................................................... 27
Vehicle Safety............................................................................................................................................................ 27
CONTENTS
4 Dragonfly
Nano MTQN-MNG1-B01 Device Guide
Device Maintenance ................................................................................................................................................. 28
User Responsibility.................................................................................................................................................... 28
Chapter 6 Getting Started ................................................................................................................................... 29
Developing with an MTQN in Mbed ........................................................................................................................... 29
Mbed Documentation............................................................................................................................................... 29
ST Microcontroller STM32L471QG ........................................................................................................................... 30
Chapter 7 Labels.................................................................................................................................................. 31
Approvals and Certifications....................................................................................................................................... 31
Example Labels.......................................................................................................................................................... 31
Chapter 8 Regulatory Information....................................................................................................................... 32
47 CFR Part 15 Regulation Class B Devices ................................................................................................................. 32
FCC Interference Notice............................................................................................................................................ 32
FCC Grant .................................................................................................................................................................. 32
Chapter 9 Environmental Notices........................................................................................................................ 34
Waste Electrical and Electronic Equipment Statement .............................................................................................. 34
WEEE Directive.......................................................................................................................................................... 34
Instructions for Disposal of WEEE by Users in the European Union ........................................................................ 34
Restriction of the Use of Hazardous Substances (RoHS) ............................................................................................ 34
REACH Statement ....................................................................................................................................................... 35
Registration of Substances ........................................................................................................................................ 35
Information on HS/TS Substances According to Chinese Standards (in Chinese) ...................................................... 36
Information on HS/TS Substances According to Chinese Standards ......................................................................... 37
Chapter 10 Using Connection Manager ............................................................................................................... 38
Installing Connection Manager ................................................................................................................................... 38
Setting Up a Serial Device in Windows Device Manager............................................................................................ 39
Connecting a Device.................................................................................................................................................... 41
Uninstalling Connection Manager............................................................................................................................... 42
Connection Manager User Interface........................................................................................................................... 42
Main tab.................................................................................................................................................................... 43
Settings tab ............................................................................................................................................................... 44
Connection tab.......................................................................................................................................................... 44
Details tab ................................................................................................................................................................. 44
Terminal tab.............................................................................................................................................................. 44
Charts tab.................................................................................................................................................................. 44
Troubleshooting.......................................................................................................................................................... 44
Serial COM port is not available in the Serial Modem Settings................................................................................ 44
Device is not detected ("No Device") ....................................................................................................................... 44
MultiConnect Cell USB Modem is not detected ....................................................................................................... 45
Connection Manager is not working, and a device connected to the computer is not detected............................ 45
Connection Manager displays "Device Error" status for a serial device .................................................................. 45
CONTENTS
Dragonfly
Nano MTQN-MNG1-B01 Device Guide 5
Index...................................................................................................................................................................... 46
PRODUCT OVERVIEW
6 Dragonfly
Nano MTQN-MNG1-B01 Device Guide
Chapter 1 Product Overview
Overview
The Dragonfly
TM
Nano (MTQN) cellular System-on-Module (SoM) is a small version of the Dragonfly (MTQ) System-
on-Module (SoM). Both embedded devices offer developers the functionality of an on-board cellular radio all-in-
one compact design. The Dragonfly Nano provides a practical solution to the market's demand for a smaller, low-
power module.
The Dragonfly Nano functions similarly to the Dragonfly and maintains interoperability with legacy systems that
use a 40-pin connector and forward mounting hole. All Dragonfly software is open source.
Documentation
This documentation is on the product page at https://www.multitech.com/brands/multiconnect-dragonfly-nano.
Document Description Part Number
MTQN-MNG1-B01 Device
Guide
Provides model specifications and developer information
regarding the B01 version of MTQN.
S000671
Universal Developer Kit 2.0
Developer Guide.
Provides information for using the developer board with
the MTQN.
S000610
ST Microcontroller Data Sheet Data sheet for processor STM32L471QG:
https://www.st.com/en/microcontrollers/stm32l471qg.htm
l
027226 Rev 1
Sara-R4 USB Driver Installation
Guide
Provides instructions on how to install Windows USB driver. N/A
Sara-R4/N4 series, AT
Commands Manual
Provides AT commands and parameters used to configure
your device.
UBX-17003787
Note: Additional documentation is available on the mbed site at https://os.mbed.com/platforms/MTS-
Dragonfly-Nano/ and at www.multitech.net. See Chapter 6, Getting Started for details.
Product Build Options
The available Dragonfly
TM
Nano modules are:
Model Description Region
MTQN-MNG1-B01 Embedded LTE Cat M1 Cellular SoM (Verizon/AT&T) North America
Developer Kit
MTUDK2-ST-CELL SocketModem
®
& Dragonfly
TM
Nano Developer Kit Global
Note: These units ship without network activation. To connect them to the cellular network, you need SIM cards
from your service provider. The complete product code may end in .Rx. For example, MTQN-MNG1-B01.Rx, where
R is revision and x is the revision number. All builds can be ordered individually or in 50-packs.
MECHANICAL DRAWINGS
Dragonfly
Nano MTQN-MNG1-B01 Device Guide 7
Chapter 2 Mechanical Drawings
MTQN-MNG1-B01
HARDWARE AND SPECIFICATIONS
8 Dragonfly
Nano MTQN-MNG1-B01 Device Guide
Chapter 3 Hardware and Specifications
Specifications
Category Description
Performance
1
3GPP Release 13 Cat M1 Half Duplex (Up to 375K bps downlink and uplink)
Frequency Band
(MHz)
AT&T Verizon
700 MHz (B12), 850 MHz (B5),
AWS1700 MHz (B4) and 1900 MHz
(B2)
700 MHz (B13)
Interface
Connectors 1 UFL (Cellular), 1x Micro USB, 1x 40-Pin Board-to-Board
Host Processor Cortex-M4 (STM32L471QG) 1 Mbyte Flash and 128 Kbyte SRAM (B01)
I/O 1 x UART, 1 x HS USB, 2 x SPI, 2 x I2C, up to 9 analog inputs and up to 29 digital input/output
SMS Mobile Terminate/Mobile Originate PDU / Text mode
Physical Description
Weight less than 0.3 oz (8.5g)
Dimensions 28.96mm x 32.51mm (1.14 x 1.28 inches). Refer to Mechanical Drawings for details.
Connectors
Antenna 1 surface mount U.FL: cellular
SIM Holder 1.8 V and 3 V Micro SIM (3FF) card. SIM denotes: Subscriber Identity Module.
Pin header 40-pin female for USB or UART
Environment
Operating
Temperature
2
-40° C to +85° C (-40° F to +185° F)
Storage
Temperature
-40° C to +85° C (-40° F to +185° F)
Humidity
3
15%-93% RH, non-condensing
1
Actual performance speeds may be affected by a variety of attributes such as cell tower distance, data loads,
packet sizes, etc.
2
Device has been tested up to +85° C. UL Recognized @ 85° C.
3
Radio performance may be affected by temperature extremes. This is normal.
The following table defines the remaining specifications for the MTQN-MNG1.
Category Description
Certifications and Compliance
HARDWARE AND SPECIFICATIONS
Dragonfly
Nano MTQN-MNG1-B01 Device Guide 9
Category Description
EMC Compliance FCC Part 15 Class B
Radio Compliance FCC Part 22, 24, 27
Safety Compliance UL/cUL 60950-1 2nd ED, IEC 60950-1 2nd ED +Am.2
Network PTCRB N/A
Carrier AT&T Verizon
Mounting Hardware
The board has two mounting holes at the corners. Use #4 or M3 hardware for mounting the Dragonfly Nano to the
board. Refer to the Mechanical Drawings for more information.
Here are some standoffs that can be used with this product.
Recommended Parts
Manufacturer Part Part Number
PEM (Penn Engineering &
Manufacturing)
Surface Mount Standoff SMTSO-M3-4ET
RAF Electronic Hardware 3/16” Hex Female Standoff 2051T-440-S-12-Zinc
RAF Electronic Hardware 4.5mm Hex Female Standoff 1251-3005-S-12-Zinc
40-Pin Connector Definitions
The Dragonfly™ Nano offers developers an FCC and carrier certified solution that makes connecting sensors and
other edge-of-network devices quick and easy.
40-Pin Connector
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21
HARDWARE AND SPECIFICATIONS
10 Dragonfly
Nano MTQN-MNG1-B01 Device Guide
MTQN-MNG1-B01 Pin Definitions
Note:
To program and use the Dragonfly™ Nano, you will need a UDK2 Developer Kit.
For more pinout information and other details, refer to the STM32L471QG processor manual. In addition to their
stated functions, all GPIO pins (PA_*, PB_*, PC_*, PG_*) can also be used as Digital-In and Digital-Out interfaces.
Hardware Pinout Information
HARDWARE AND SPECIFICATIONS
Dragonfly
Nano MTQN-MNG1-B01 Device Guide 11
Processor Pin
Number
Processor Pin
Name
IO Type Net name 40 Pin UDK2 pin
/Arduino
Primary
Function
B5 PB6 FT_fa DBG_TX 1 Programming,
Output from
MTQN
A10 PA14_SWCLK FT J_TCK/SWCLK 2 Programming
A9 PA15 FT J_TDI/C_MON 3 Programming
A7 PB4 FT_a J_RST 4 Programming
J1 GND GND 5 GND
F2 VSS1 GND 13 GND
E3 VSS2 GND 28 GND
F6 VSS3 GND 36 GND
F12 VSS4 GND 37 GND
F11 VSS5 GND 5 GND
F7 VSS6 GND 5 GND
D3 VSS7 GND 5 GND
USB_DP USB_DP 6 USB_DP
USB_DM USB_DM 7 USB_DM
VCC-IN VCC-IN 8 VCC-IN
VCC-IN VCC-IN 33 VCC-IN
K3 PA2 FT_a IO_00/RXD 9 D1 Serial Comm
output from
MTQN
J5 PA7 FT_a IO_01/DCD 10 D4 Serial Comm
output from
MTQN
M5 PB0 TT_a IO_02/RI 11 D8 Serial Comm
output from
MTQN
M2 PA1 FT_a IO_03/RTS 12 D6 Serial Comm
input to MTQN
C5 PB5 FT_a IO_04/MOSI1 14 D11 GPIO / MOSI
output from
MTQN
G10 PG2 FT_s IO_05/SCK1 15 D13 GPIO & PA5 as
well
A3 PB8 FT_f IO_06/SCL/SS1 16 D15 GPIO, 4.7K pull
up
HARDWARE AND SPECIFICATIONS
12 Dragonfly
Nano MTQN-MNG1-B01 Device Guide
Processor Pin
Number
Processor Pin
Name
IO Type Net name 40 Pin UDK2 pin
/Arduino
Primary
Function
K10 PB15 FT IO_07/MOSI2 17 D2 GPIO / MOSI
output from
MTQN
J3 PC2 FT_a IO_08/MISO2 18 A0 GPIO / MISO
input to MTQN
D2 PE6 FT IO_09 19 A3 GPIO
C1 PC13 FT IO_10 20 A1 GPIO
L4 PA6 FT_a IO_11 21 A4 GPIO
K5 PC4 FT_a IO_12 22 A2 GPIO
L10 PB10 FT_f IO_13/SCK2 23 D9 GPIO
J6 PG8 FT_fs IO_14 24 A5 GPIO
B3 PB9 FT_f IO_15/SDA/SR
DY
25 D14 GPIO, 4.7K pull
up
F9 PG3 FT_s IO_16/MISO1 26 D12 GPIO / MISO
input to MTQN
E10 PC8 FT IO_17/SS2 27 D10 GPIO
L2 PA0 FT_a IO_18/CTS 29 D3 Serial Comm
output from
MTQN
D10 PA9 FT IO_19/DSR 30 D5 Serial Comm
output from
MTQN
H4 PG7 FT_fs IO_20/DTR 31 D7 Serial Comm
input to MTQN
L3 PA3 TT IO_21/TXD 32 D0 Serial Comm
input to MTQN
LS 34 Link status
output from
Cell radio, 47K
pull up
A8 PB3 FT_a J_TDO/SWO 38 JTAG
A11 PA13_SWDIO FT J_TMS/SWDIO 39 JTAG
B4 PB7 FT_fa DBG_RX 40 Programming,
Input to MTQN
A4 BOOT0 B 3V3 or GND Boot option,
tied low
GND
HARDWARE AND SPECIFICATIONS
Dragonfly
Nano MTQN-MNG1-B01 Device Guide 13
Processor Pin
Number
Processor Pin
Name
IO Type Net name 40 Pin UDK2 pin
/Arduino
Primary
Function
H2 NRST Reset N_RESET Reset Input,
47K pull up,
active low
NRST_IN 35 Reset input
from 40-Pin,
connected to
NRST by 47K
resistor
NRST_IN
L12 PB12 FT VCC-
IN_MEAS_EN
Control for
enabling
power
measurement,
pulled low
with 100K
resistor
H1 PC0 FT_fa VCC-IN_MEAS Ananlog power
measurement
B11 PC10 FT FLASH_SCK FLASH_SCK,
47K pull down
C10 PC11 FT FLASH_MISO FLASH_MISO
B10 PC12 FT FLASH_MOSI FLASH_MOSI
D1 PC14_OSC32IN FT 32K Clock 32K Clock
E1 PC15_OSC32O
UT
FT 32K Clock 32K Clock
K2 PC3 FT_a RADIO_PWR RADIO_PWR,
enable for cell
regulator, 47K
pull down
L5 PC5 FT_a 1V8_MON Radio Control
Feedback,
100K pull
down
E12 PC6 FT BUF_EN Buffer Power
Control, 100K
pull up, active
low
J12 PD10 FT RADIO_RI Serial for
Radio
J11 PD11 FT RADIO_CTS Serial for
Radio
HARDWARE AND SPECIFICATIONS
14 Dragonfly
Nano MTQN-MNG1-B01 Device Guide
Processor Pin
Number
Processor Pin
Name
IO Type Net name 40 Pin UDK2 pin
/Arduino
Primary
Function
J10 PD12 FT RADIO_RTS Serial for
Radio
H12 PD13 FT RADIO_DTR Serial for
Radio
H11 PD14 FT RADIO_DCD Serial for
Radio
H10 PD15 FT RADIO_DSR Serial for
Radio
K9 PD8 FT RADIO_TXD Serial for
Radio
K8 PD9 FT RADIO_RXD Serial for
Radio
A2 PE1 FT VMEM_EN Power control
for Flash, 100K
pull up, active
low
M9 PE11 FT CELL_GPIO5 GPIO to RADIO
M10 PE13 FT CELL_GPIO2 GPIO to RADIO
M11 PE14 FT CELL_GPIO3 GPIO to RADIO
M12 PE15 FT CELL_GPIO4 GPIO to RADIO
A1 PE3 FT VUSB_DET USB Select,
Active low for
Serial mode,
100K pull
down
B1 PE4 FT RADIO_ONOFF Radio power
control, 100K
pull down
E4 PF3 FT_a RADIO_RESET RADIO_RESET
control, 100K
pull down
D7 PG12 FT_s FLASH_NSS FLASH_NSS,
active low
E2 VBAT VRTC VRTC
G2 VDD1 3V3 3V3
H3 VDD2 3V3 3V3
G6 VDD3 3V3 3V3
G12 VDD4 3V3 3V3
HARDWARE AND SPECIFICATIONS
Dragonfly
Nano MTQN-MNG1-B01 Device Guide 15
Processor Pin
Number
Processor Pin
Name
IO Type Net name 40 Pin UDK2 pin
/Arduino
Primary
Function
C11 VDD5 3V3 3V3
G11 VDD6 3V3 3V3
C4 VDD7 3V3 3V3
M1 VDDA 3V3 3V3
G7 VDDIO2 3V3 3V3
L1 VREF+ 3V3 3V3
Data taken from STM32L471QG processor datasheet.
Key for IO type values:
FT 5V tolerant IO
TT 3.6V tolerant IO
B Dedicated Boot pin
RST Reset pin
_f IO, Fm+ capable
_a IO, with Analog supplied by VDDA
_s IO, supplied by VDDIO2
Software Pinout Information
The names in this table are defined in the PinNames.h file in mbed-os at the following path: mbed-
os\targets\target_stm\target_stm32l4\target_mts_dragonfly_l471qg
Pin UDK2 Primary Alternate names
PA_0 D3 UART2_CTS TIM5_1, ADC1_IN13,
ADC2_IN13, SERIAL_CTS,
IO_18, WAKEUP, LED1,
LED2, LED3, LED4
PA_1 D6 UART2_RTS TIM5_2, ADC1_IN6,
ADC2_IN6, SERIAL_RTS,
IO_03
PA_13 J_TMS
PA_14 J_TCK
PA_15 J_TDI TIM2_1
PA_2 D1 UART2_TX TIM2_3, TIM5_3,
ADC1_IN7, ADC2_IN7,
SERIAL_TX , IO_00
HARDWARE AND SPECIFICATIONS
16 Dragonfly
Nano MTQN-MNG1-B01 Device Guide
Pin UDK2 Primary Alternate names
PA_3 D0 UART2_RX ADC1_IN8, ADC2_IN8,
SERIAL_RX , IO_21
PA_6 A4 IO_11 ADC1_IN11, ADC2_IN11
PA_7 D4 UART2_DCD TIM3_2, TIM7_1,
ADC1_IN12, ADC2_IN12,
SERIAL_DCD, IO_01
PA_9 D5 UART2_DSR SERIAL_DSR, IO_19
PB_0 D8 SERIAL_RI TIM3_3, ADC1_IN15,
ADC2_IN15, IO_02
PB_10 D9 SPI2_SCK IO_13
PB_12 VCC_IN_MEAS_EN
PB_15 D2 SPI2_MOSI IO_07
PB_3 J_TDO TIM2_2
PB_4 J_RST TIM3_1
PB_5 D11 SPI1_MOSI IO_04
PB_6 UART1_TX USBTX
PB_7 UART1_RX USBRX
PB_8 D15 I2C1_SCL TIM4_3, CAN1_RX, IO_06
PB_9 D14 I2C1_SDA CAN1_TX, IO_15
PC_0 VCC_IN_MEAS
PC_10 SPI3_SCK
PC_11 SPI3_MISO
PC_12 SPI3_MOSI
PC_13 A1 IO_10
PC_14 32K
PC_15 32K
PC_2 A0 SPI2_MISO ADC1_IN3, ADC2_IN3,
ADC3_IN3, IO_08,
ADC1_IN1, ADC2_IN1,
ADC3_IN1
PC_3 RADIO_PWR
PC_4 A2 IO_12 ADC1_IN13, ADC2_IN13
PC_5 MON_1V8
PC_6 BUF_EN
PC_8 D10 IO_17 TIM8_3
HARDWARE AND SPECIFICATIONS
Dragonfly
Nano MTQN-MNG1-B01 Device Guide 17
Pin UDK2 Primary Alternate names
PD_10 RADIO_RI MDMRI
PD_11 RADIO_CTS MDMCTS, UART3_CTS
PD_12 RADIO_RTS MDMRTS, UART3_RTS
PD_13 RADIO_DTR MDMDTR
PD_14 RADIO_DCD MDMDCD
PD_15 RADIO_DSR MDMDSR
PD_8 RADIO_TX MDMTXD
PD_9 RADIO_RX MDMRXD , UART3_RX
PE_1 VMEM_EN
PE_11 CELL_GPIO5
PE_13 CELL_GPIO2
PE_14 CELL_GPIO3
PE_15 CELL_GPIO4
PE_3 VUSB_DET
PE_4 RADIO_ONOFF MDMPWRON
PE_6 A3 IO_09
PF_3 RADIO_RESET MDMRST
PG_12 SPI3_SSEL
PG_2 D13 SPI1_SCK IO_05
PG_3 D12 SPI1_MISO IO_16
PG_7 D7 UART2_DTR I2C3_SCL, SERIAL_DTR,
IO_20
PG_8 A5 IO_14 I2C3_SDA
40-Pin Connector
Manufacturer: Hirose Electric Co LTD
Description: Plug
Model Number: DF17(2.0)-40DP-0.5V(57)
Communications Flow
MTQN-MNG1-B01
The MTQN-MNG1-B01 provides full UART from the cellular radio to the processor as well as the user application.
Model B01 provides a direct USB interface connection to the radio, but not through the 40-pin connector.
HARDWARE AND SPECIFICATIONS
18 Dragonfly
Nano MTQN-MNG1-B01 Device Guide
Switching between the USB interface and serial port requires a reset. The cellular radio checks for a USB
connection upon reset. If USB is not present, it only uses the serial port. If USB is present upon reset, it only uses
USB.
Electrical Characteristics
Operating Conditions
Parameter Minimum Volts Maximum Volts
Supply Range - Vcc 3.2 5.25
Absolute Maximum Ratings
Symbol Description Conditions Min. Max. Unit
SIM SIM interface Input DC voltage at SIM digital
interfaces pins
-0.3 3.9 V
P_ANT Antenna power Input RF power at ANT pin -22 dbM
Rho_ANT Antenna ruggedness Output RF load mismatch
ruggedness at ANT pins
10.1 VSWR
tstg Storage Temperature -40 85 °C
V
P
Voltage at any pin Voltage at any signal pin -0.3 4 V
V
DDX
- V
SS
External voltage V
DDX
, V
DDA
,V
DDIO2
, V
BAT
1
-0.3 4 V
V
IN
2
Input Voltage Input voltage on FT_xxx pins V
SS
-0.3 min (V
DD
,
V
DDA
,V
DDIO2
)+
4.0
3 & 4
V
Input voltage on TT_xx pins V
SS
-0.3 4.0 V
Input voltage on BOOT0 pin V
SS
9.0 V
Input voltage on any other pins V
SS
-0.3 4.0 V
HARDWARE AND SPECIFICATIONS
Dragonfly
Nano MTQN-MNG1-B01 Device Guide 19
Symbol Description Conditions Min. Max. Unit
|ΔV
DDx|
Variations between
power pins
Variations between
different V
DDX
power pins of
the same domain
N/A 50 mV
|V
SSx
-V
SS
| Variations between
ground pins
Variations between all the
different ground pins
5
N/A 50 mV
Data taken from STM32L471QG processor datasheet.
(1) All main power (V
DD
, V
DDA
, V
DDIO2
, V
BAT
) and ground (V
SS
, V
SSA
) pins must always be connected to the external power
(2) V
IN
maximum must always be respected. Refer to Nominal Ratings for the maximum allowed injected current
values.
(3) This formula has to be applied only on the power supplies related to the IO structure described in the pin
definition table.
(4) To sustain a voltage higher than 4 V the internal pull-up/pull-down resistors must be disabled.
(5) Include VREF- pin.
Nominal Ratings
Symbol Ratings Max Voltage
(mA)
ΣIV
DD
Total current into sum of all VDD power lines (source)
1
150
ΣIV
SS
Total current out of sum of all VSS ground lines (sink)
1
150
IV
DD(PIN)
Maximum current into each VDD power pin (source)
1
100
IV
SS(PIN)
Maximum current out of each VSS ground pin (sink)
1
100
I
IO(PIN)
Output current sunk by any I/O and control pin except FT_f 20
Output current sunk by any FT_f pin 20
Output current sourced by any I/O and control pin 20
ΣI
IO(PIN)
Total output current sunk by sum of all I/Os and control
pins
2
100
Total output current sourced by sum of all I/Os and control
pins
2
100
I
INJ(PIN)
3
Injected current on FT_xxx, TT_xx, RST and B pins, except
PA4, PA5
-5/+0
4
Injected current on PA4, PA5
HARDWARE AND SPECIFICATIONS
20 Dragonfly
Nano MTQN-MNG1-B01 Device Guide
Symbol Ratings Max Voltage
(mA)
Σ|I
INJ(PIN)
| Total injected current (sum of all I/Os and control pins)
5
-5/0
25
Data taken from STM32L471QG processor datasheet.
(1) All main power (V
DD
, V
DDA
, V
DDIO2
, V
BAT
) and ground (V
SS
, V
SSA
) pins must always be connected to the external
power, in permitted range.
(2) This current consumption must be correctly distributed over all I/Os and control pins. The total output current
must not be sunk/sourced between two consecutive power supply pins referring to high pin count QFP packages.
(3) Positive injection (when V
IN
> V
DDIOx
) is not possible on these I/Os and does not occur for input voltages lower
than the specified maximum value.
(4) A negative injection is induced by V
IN
< V
SS. IINJ(PIN)
must never be exceeded. Refer to the Absolute Maximum
Ratings table for the minimum allowed input voltage values.
(5) When several inputs are submitted to a current injection, the maximum Σ|I
INJ(PIN)
| is the absolute sum of the
negative injected currents (instantaneous values).
Power Draw
Voltage Radio
Protocol
Sleep Mode
Current
Power Saving
Mode
(AVG)
Measured
Current at
Max Power
1
TX Pulse
2
(AVG)
Amplitude Current for
Peak Current
Total Inrush
Charge
3
in
MilliCoulombs
(mC)
3.8 VDC LTE 21.943 μA
5.0 VDC LTE 4.702 μA 155.421 mA 315.532 mA 0.00792
1
Maximum Power: The continuous current during maximum data rate with the radio transmitter at maximum
power.
2
Tx Pulse: The average peak current during a GSM 850 transmission burst period or LTE connection. The
transmission burst duration for GSM 850 can vary, depending on what transmission scheme is being deployed
(GPRS Class 8, Class 10, GSM, etc.).
3
Inrush Charge: The total inrush charge at power on.
USB Cable Recommendations
If your device has a USB connector, to avoid enumeration or power issues:
Use a high-speed USB cable that is as short as possible.
Use a well-shielded cable with at least 24 AWG wire pair for power/ground and 28 AWG wire pair for data
lines.
If possible, use a USB port that connects directly to the motherboard rather than a USB port with added
cabling inside the computer chassis.
Use USB 3.0 ports if available. These ports are typically rated for more current.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46

Multitech MTQN-MNG1-B01.R1 Mode d'emploi

Catégorie
La mise en réseau
Taper
Mode d'emploi
Ce manuel convient également à

dans d''autres langues