Allen-Bradley 1783-EMS04T Installation Instructions Manual

Marque
Allen-Bradley
Modèle
1783-EMS04T
Catégorie
Convertisseurs de média réseau
Taper
Installation Instructions Manual

Ce manuel convient également à

Installation Instructions
Original Instructions
Stratix 6000 Ethernet Managed Switches
Catalog Numbers 1783-EMS08T, 1783-EMS04T
Topic Page
Summary of Changes 2
About the Switch 8
Install the Switch 8
DIN Rail Mounting 9
Panel Mounting 11
Wire the Switch 12
Connect the Copper Ethernet Ports 13
Install an Optional SFP Module 14
Connect the Fiber-optic Ethernet Port 15
Grounding Considerations 15
Use the Switch 16
Specifications 18
Additional Resources 20
2 Rockwell Automation Publication 1783-IN004C-EN-P - April 2016
Stratix 6000 Ethernet Managed Switches
Summary of Changes
This publication contains new and updated information as indicated in the
following table.
Topic Page
ATEX certification and temp code 5, 19
China RoHS table 7
ATTENTION statement about using shielded Ethernet cables 13
ATTENTION: Environment and Enclosure
This equipment is intended for use in a Pollution Degree 2 industrial environment,
in overvoltage Category II applications (as defined in EN/IEC 60664-1), at altitudes
up to 2000 m (6562 ft) without derating.
This equipment is not intended for use in residential environments and may not
provide adequate protection to radio communication services in such
environments.
This equipment is supplied as open-type equipment for indoor use. It must be
mounted within an enclosure that is suitably designed for those specific
environmental conditions that will be present and appropriately designed to
prevent personal injury resulting from accessibility to live parts. The enclosure must
have suitable flame-retardant properties to prevent or minimize the spread of
flame, complying with a flame spread rating of 5VA or be approved for the
application if nonmetallic. The interior of the enclosure must be accessible only by
the use of a tool. Subsequent sections of this publication may contain more
information regarding specific enclosure type ratings that are required to comply
with certain product safety certifications.
In addition to this publication, see the following publications:
• Publication
1770-4.1, Industrial Automation Wiring and Grounding Guidelines,
for more additional installation requirements
• NEMA 250 and IEC 60529, as applicable, for explanations of the degrees of
protection provided by different types of enclosures
Rockwell Automation Publication 1783-IN004C-EN-P - April 2016 3
Stratix 6000 Ethernet Managed Switches
ATTENTION: Read this document and the documents listed in the Additional
Resources section about installation, configuration, and operation of this
equipment before you install, configure, operate, or maintain this product. Users
are required to familiarize themselves with installation and wiring instructions in
addition to requirements of all applicable codes, laws, and standards.
ATTENTION: Activities including installation, adjustments, putting into service,
use, assembly, disassembly, and maintenance are required to be carried out by
suitably trained personnel in accordance with applicable code of practice.
In case of malfunction or damage, no attempts at repair should be made. The
module should be returned to the manufacturer for repair. Do not dismantle the
module.
ATTENTION: This equipment is certified for use only within the surrounding air
temperature range of 0…60 °C (32…140 °F). The equipment must not be used
outside of this range.
ATTENTION: Electrical Safety Considerations
Power to this equipment must be supplied from a source compliant with the
following:
• Class 2 approved to UL1310
• SELV source approved to EN/IEC60950-1, EN/IEC61010-2-201 or
EN/IEC62368-1 (ES1)
4 Rockwell Automation Publication 1783-IN004C-EN-P - April 2016
Stratix 6000 Ethernet Managed Switches
North American Hazardous Location Approval
The following information applies when
operating this equipment in hazardous
locations.
Informations sur l’utilisation de cet
équipement en environnements dangereux.
Products marked "CL I, DIV 2, GP A, B, C, D" are
suitable for use in Class I Division 2 Groups A, B, C,
D, Hazardous Locations and nonhazardous locations
only. Each product is supplied with markings on the
rating nameplate indicating the hazardous location
temperature code. When combining products
within a system, the most adverse temperature
code (lowest "T" number) may be used to help
determine the overall temperature code of the
system. Combinations of equipment in your system
are subject to investigation by the local Authority
Having Jurisdiction at the time of installation.
Les produits marqués "CL I, DIV 2, GP A, B, C, D" ne
conviennent qu'à une utilisation en environnements
de Classe I Division 2 Groupes A, B, C, D dangereux et
non dangereux. Chaque produit est livré avec des
marquages sur sa plaque d'identification qui
indiquent le code de température pour les
environnements dangereux. Lorsque plusieurs
produits sont combinés dans un système, le code de
température le plus défavorable (code de
température le plus faible) peut être utilisé pour
déterminer le code de température global du
système. Les combinaisons d'équipements dans le
système sont sujettes à inspection par les autorités
locales qualifiées au moment de l'installation.
EXPLOSION HAZARD -
• Do not disconnect equipment
unless power has been
removed or the area is known
to be nonhazardous.
• Do not disconnect connections
to this equipment unless
power has been removed or
the area is known to be
nonhazardous. Secure any
external connections that
mate to this equipment by
using screws, sliding latches,
threaded connectors, or other
means provided with this
product.
• Substitution of components
may impair suitability for Class
I, Division 2.
• If this product contains
batteries, they must only be
changed in an area known to
be nonhazardous.
RISQUE D’EXPLOSION –
• Couper le courant ou s'assurer
que l'environnement est classé
non dangereux avant de
débrancher l'équipement.
• Couper le courant ou s'assurer
que l'environnement est classé
non dangereux avant de
débrancher les connecteurs.
Fixer tous les connecteurs
externes reliés à cet
équipement à l'aide de vis,
loquets coulissants,
connecteurs filetés ou autres
moyens fournis avec ce
produit.
• La substitution de composants
peut rendre cet équipement
inadapté à une utilisation en
environnement de Classe I,
Division 2.
• S'assurer que l'environnement
est classé non dangereux
avant de changer les piles.
Rockwell Automation Publication 1783-IN004C-EN-P - April 2016 5
Stratix 6000 Ethernet Managed Switches
European Hazardous Location Approval
The following applies to products marked II 3 G:
• Are Equipment Group II, Equipment Category 3, and comply with the Essential Health
and Safety Requirements relating to the design and construction of such equipment
given in Annex II to Directive 94/9/EC. See the EC Declaration of Conformity at
http://www.rockwellautomation.com/products/certification for details.
• The type of protection is <Ex ic nA IIC T4 Gc> according to EN 60079-15 and
EN 60079-11.
• Comply to Standards <EN 60079-0:2012, EN 60079-15:2010, EN60079-11:2012>,
reference certificate number <ITS09ATEX46141U>.
• Are intended for use in areas in which explosive atmospheres caused by gases, vapors,
mists, or air are unlikely to occur, or are likely to occur only infrequently and for short
periods. Such locations correspond to Zone 2 classification according to ATEX directive
1999/92/EC.
WARNING: Special Conditions for Safe Use
• This equipment is not resistant to sunlight or other sources of UV radiation.
• This equipment shall be mounted in an ATEX Zone 2 certified enclosure with a
minimum ingress protection rating of at least IP54 (as defined in EN 60529) and
used in an environment of not more than Pollution Degree 2 (as defined in
EN 60664-1) when applied in Zone 2 environments. The enclosure must be
accessible only by the use of a tool.
• This equipment shall be used within its specified ratings defined by Rockwell
Automation®.
• Provision shall be made to prevent the rated voltage from being exceeded by
transient disturbances of more than 140% of the rated voltage when applied in
Zone 2 environments.
• The instructions in the user manual shall be observed.
• Secure any external connections that mate to this equipment by using screws,
sliding latches, threaded connectors, or other means provided with this product.
• Do not disconnect equipment unless power has been removed or the area is
known to be nonhazardous.
6 Rockwell Automation Publication 1783-IN004C-EN-P - April 2016
Stratix 6000 Ethernet Managed Switches
ATTENTION: Prevent Electrostatic Discharge
This equipment is sensitive to electrostatic discharge, which can cause internal
damage and affect normal operation. Follow these guidelines when you handle
this equipment:
• Touch a grounded object to discharge potential static.
• Wear an approved grounding wriststrap.
• Do not touch connectors or pins on component boards.
• Do not touch circuit components inside the equipment.
• Use a static-safe workstation, if available.
• Store the equipment in appropriate static-safe packaging when not in use.
WARNING: If you connect or disconnect the communications cable with power
applied to this module or any device on the network, an electrical arc can occur.
This could cause an explosion in hazardous location installations.
Be sure that power is removed or the area is nonhazardous before proceeding.
WARNING: If you connect or disconnect wiring while the field-side power is on,
an electrical arc can occur. This could cause an explosion in hazardous location
installations. Be sure that power is removed or the area is nonhazardous before
proceeding.
At the end of its life, this equipment should be collected separately from any
unsorted municipal waste.
Rockwell Automation Publication 1783-IN004C-EN-P - April 2016 7
Stratix 6000 Ethernet Managed Switches
Name and Content of Hazardous Substances in Product
Component
Name
Hazardous Substances
Lead
(Pb)
Mercury
(Hg)
Cadmium
(Cd)
Hexavalent
Chromium
(Cr(VI))
Polybrominated
Biphenyls
(PBB)
Polybrominated
Diphenyl Ethers
(PBDE)
Printed circuit
board assemblies
xo o o o o
Metal
components
xo o o o o
Plastic
Components
oo o o o o
This table is made per guidance of SJ/T 11364.
O: Indicates that this hazardous substance contained in all of the homogeneous materials for the part is
below the limit requirement in GB/T 26572.
X: Indicates that this hazardous substance contained in at least one of the homogeneous materials used for
this part is above the limit requirement in GB/T 26572.
(According to actual situation, extra explanations can be given here for the technical reasons of items with
"X".)
8 Rockwell Automation Publication 1783-IN004C-EN-P - April 2016
Stratix 6000 Ethernet Managed Switches
About the Switch
The Stratix 6000™ switch provides real-time access to network data through the
Logix control system. The switch integrates into Logix programs and update
tags automatically.
Use the switch to help continuously monitor your network and implement
changes.
The figure shows Ethernet port identification for the 1783-EMS08T 8-port and
the 1783-EMS04T 4-port switches.
Ethernet Port Identification
Install the Switch
Mount the switch in the vertical position only, as shown. We do not recommend
horizontal mounting due to thermal considerations. When mounting, follow
these guidelines:
• Provide 50 mm (2 in.) of space on all sides for adequate heat dissipation.
• Leave 100 mm (4 in.) for installation and removal for the fiber-optic
port on the bottom of the 1783-EMS08T switch.
IMPORTANT Use care with the plastic DIN-rail clip.
1
1
2
34
56
78
2
3
4
1
2
3
4
8
6
4
2
7
5
3
1
1783-EMS08T1783-EMS04T
31871-M
Rockwell Automation Publication 1783-IN004C-EN-P - April 2016 9
Stratix 6000 Ethernet Managed Switches
DIN Rail Mounting
Read this section to install and remove a switch that uses DIN rail mounting.
Install the Switch
To install the switch on DIN rail, proceed as follows.
1. Mount your DIN rail.
2. Snap the DIN rail latch into the closed position.
3. Hook the top slot over the DIN rail and push the switch into position
on the DIN rail.
10 Rockwell Automation Publication 1783-IN004C-EN-P - April 2016
Stratix 6000 Ethernet Managed Switches
Remove the Switch
To remove the switch from DIN rail, proceed as follows.
1. Place a screwdriver in the DIN rail latch at the bottom of the switch.
2. Hold the switch and pry downward on the latch until the switch is
released from the DIN rail.
Rockwell Automation Publication 1783-IN004C-EN-P - April 2016 11
Stratix 6000 Ethernet Managed Switches
Panel Mounting
To panel mount a switch, create a mounting template. Refer to the following
figure, which shows a 1783-EMS08T switch with a small form-factor pluggable
(SFP) module installed.
Provide 15 mm (0.6 in.) clearance for DIN rail latch movement during
installation and removal. Dimensions in the figure are in mm (in.). These views
are not actual size.
27.7 (1.09)
52.07 (2.05)
107 (4.21)
118 (4.64)
88.9 (3.50)
12 (0.47)
12 (0.47)
SFP Module Installed
12 Rockwell Automation Publication 1783-IN004C-EN-P - April 2016
Stratix 6000 Ethernet Managed Switches
Wire the Switch
Read this section for information about external power supply wiring.
Provide low voltage DC power to the switch by using the screw terminals at the
bottom of the switch.
Item Description Item Description
1 Side view 4 Ground
2 Bottom view 5 DC-
3 Fiber-optic SFP slot (1783-EMS08T switch only) 6 DC +
1
2
46
3
5
Rockwell Automation Publication 1783-IN004C-EN-P - April 2016 13
Stratix 6000 Ethernet Managed Switches
Follow these steps to wire the switch.
1. Be sure that power to the power supply is turned off.
2. Be sure that you have the proper gauge of wire for your power supply.
3. Strip approximately 0.9 mm (0.35 in.) from each end of the wire.
4. Use a Phillips screwdriver to loosen the screw terminals on the terminal
strip at the bottom of the switch.
5. Connect DC+ (24V DC nominal) from the power supply to the DC+
terminal and tighten the screw.
6. Connect DC- (0V DC) from the power supply to the DC- terminal and
tighten the screw.
7. Connect functional earth ground to the ground terminal and tighten
the screw.
See the grounding considerations on
page 15.
8. Pull gently on the wires to verify that the connections are secure.
Connect the Copper Ethernet Ports
Follow these steps to connect the copper Ethernet ports on the switch.
1. Locate the copper Ethernet RJ45 ports on the switch.
2. Connect one end of an Ethernet cable to one of the copper ports on the
switch.
3. Connect the other end of the Ethernet cable to a device in your Ethernet
network.
ATTENTION: When using shielded Ethernet cables, be sure to follow the
guidelines for use of shielded cable, especially the guidelines for eliminating
ground loops. The guidelines are documented in the ODVA EtherNet/IP Media
Planning & Installation Manual available on the ODVA website at
https://www.odva.org/Publication-Download. If the guidelines are not followed,
catastrophic damage to the switch can occur.
14 Rockwell Automation Publication 1783-IN004C-EN-P - April 2016
Stratix 6000 Ethernet Managed Switches
Install an Optional SFP Module
You can install a 1G fiber small form-factor pluggable (SFP) module into the
fiber-optic Ethernet slot on the bottom to the 1783-EMS08T switch. To install
the SFP module, grasp the module on the sides and insert it into the slot until
you feel the connector snap into place.
For detailed instructions on installing, removing, and connecting to SFP
modules, see the documentation that shipped with the SFP module.
Available SFP modules include the following:
• 1783-SFP1GSX - 1000Base-SX multi-mode fiber transceiver
• 1783-SFP1GLX - 1000Base-LX single-mode fiber transceiver
ATTENTION: (Applies only to 1783-EMS08T switches with optional SFP). Under
certain conditions, viewing the optical port may expose the eye to hazard. When
viewed under some conditions, the optical port may expose the eye beyond the
maximum permissible exposure recommendations.
ATTENTION: (Applies only to 1783-EMS08T switches with optional SFP). Class 1
laser product. Laser radiation is present when the system is open and interlocks
bypassed. Only trained and qualified personnel should be allowed to install,
replace, or service thisequipment.
31877-M
1
2
34
56
78
Rockwell Automation Publication 1783-IN004C-EN-P - April 2016 15
Stratix 6000 Ethernet Managed Switches
Connect the Fiber-optic Ethernet Port
To connect the fiber-optic Ethernet port (on the SFP) in the 1783-EMS08T
switch after inserting the SFP module, follow these steps.
1. Connect the duplex LC connector end of the fiber-optic cable, in the
proper orientation, to the fiber-optic Ethernet port on the SFP module.
The SFP module is installed at the bottom of the switch. See
Install an
Optional SFP Module.
2. Connect the other end of the cable to a device in your network or to
another switch.
Grounding Considerations
This product is intended to be mounted to a well-grounded mounting surface
such as a metal panel. The functional earth ground connection to the product is
through the specified pin on the DC connection terminals.
See publication 1770-4.1, Industrial Automation Wiring and Grounding
Guidelines, for additional information.
ATTENTION: If the SFP module cannot be fully inserted, stop! Do not force the
module into the slot. Rotate the SFP module 180 degrees and try again.
IMPORTANT The 1783-EMS08T switch supports only 1G fiber SFP modules.
IMPORTANT The ground connection is required at the grounding pin on the DC connection
terminals.
16 Rockwell Automation Publication 1783-IN004C-EN-P - April 2016
Stratix 6000 Ethernet Managed Switches
Use the Switch
To start using your switch, follow this procedure. For information about the
status indicators on the switch, refer to the Stratix 6000 Ethernet Managed
Switch User Manual, publication
1783-UM001.
1. Connect to the LAN card in your computer by using a patch or
cross-over cable, and then do the following.
a. Choose Start > Settings > Network Connections and right-click
Local Area Connection and Properties.
b. From the Local Area Connection Properties menu, check Ethernet
Protocol (TCP/IP), and click Properties.
Rockwell Automation Publication 1783-IN004C-EN-P - April 2016 17
Stratix 6000 Ethernet Managed Switches
c. From the Ethernet Protocol (TCP/IP) Properties menu, change the
IP address to 192.168.1.3 and subnet mask to 255.255.255.0.
2. Connect to the switch via a Web browser by using these steps.
a. Open a browser window.
b. Enter the default IP address of 192.168.1.1 in the address bar, press
Enter, and note the following defaults:
• User name is blank.
• Password is PASSWORD.
3. Configure the switch.
You can get complete configuration instructions by clicking the link to
view the embedded manual.
4. If the switch is to scan in a Logix5000™ program, refer to the appropriate
section of your embedded manual.
18 Rockwell Automation Publication 1783-IN004C-EN-P - April 2016
Stratix 6000 Ethernet Managed Switches
Specifications
Stratix 6000 Ethernet Managed Switches
Attribute 1783-EMS08T 1783-EMS04T
Power requirements
250 mA @ 24V DC (12…48V DC)
Class 2/SELV
100 mA @ 24V DC (12…48 V DC)
Class 2/SELV
Power dissipation 5.8 W 2.6 W
Thermal dissipation 24.6 BTU/hr @ 60 °C (140 °F) max
Network ports
8 RJ45 10/100 full/half duplex ports,
optional SFP transceiver port
4 RJ45 10/100 full/half duplex ports
Protocols TCP/IP, EtherNet/IP, Telnet, Http, DHCP, BOOTP, FTP, IGMP, SMTP
Indicators
16 port indicators,
3 status indicators
8 port indicators,
2 status indicators
EtherNet/IP features
MAC ID management, bandwidth alarming, port control, link status, scaled
bandwidth information, connections active
Switch features
VLAN, IGMP snooping, IGMP query V1
and V2, DHCP server, BOOTP server,
QoS, port mirroring
IGMP snooping, IGMP query V1 and V2,
DHCP server, BOOTP server, QoS, port
mirroring
Options 1 gigabyte fiber optic transceiver —
Voltage variation
IEC 61000-4-29:
10 ms interruption on DC supply ports
Enclosure type rating None (open-style)
Inrush current, max 2.2 A
Isolation voltage
50V (continuous), basic insulation type, power to ground and power to network
channels
No isolation between individual network channels
Routine tested at 707V AC for 1 s
Rockwell Automation Publication 1783-IN004C-EN-P - April 2016 19
Stratix 6000 Ethernet Managed Switches
Wire size
Ethernet connections:
RJ45 connector according to IEC 60603-7, 2 or 4 pair Category 5e minimum cable
according to TIA 568-B.1 or Category 5 cable according to ISO/IEC 24702
DC Power connections:
0.33…3.3 mm
2
(22...12 AWG) solid or stranded copper wire rated at 75 °C
(167 °F) or greater, 1.2 mm (3/64 in.) insulation max
Functional Ground connection:
3.3 mm
2
(12 AWG) solid or stranded copper wire rated at 75 °C (167 °F) or greater
Terminal block torque DC power and functional ground conections: 1.36 Nm (12 lb-in)
Fiber optic Ethernet
data rate
(1)
1000 Mbps
(1)
—
Fiber optic connecting
mode
(1)
Full duplex
(1)
—
Fiber optic connector
type
(1)
LC
(1)
—
Wiring category
(2)
(3)
2 - on power ports
2 - on communication ports
North American temp
code
T4
ATEX temp code T4
(1) Available when you purchase an optional SFP module.
(2) Use this Conductor Category information for planning conductor routing. See Industrial Automation Wiring and
Grounding Guidelines, publication
1770-4.1.
(3) Use this Conductor Category information for planning conductor routing as described in the appropriate system-level
installation manual.
Stratix 6000 Ethernet Managed Switches (Continued)
Attribute 1783-EMS08T 1783-EMS04T
Allen-Bradley, Logix5000, Stratix 6000, Rockwell Automation, and Rockwell Software are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400
Rockwell Automation maintains current product environmental information on its website at
http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.
Publication 1783-IN004C-EN-P - April 2016 PN-350823
Supersedes Publication 1783-IN004B-EN-P - June 2014 Copyright © 2016 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.
Additional Resources
These documents contain additional information concerning related products
from Rockwell Automation.
You can view or download publications at
http://www.rockwellautomation.com/global/literature-library/overview.page.
To order paper copies of technical documentation, contact your local
Allen-Bradley distributor or Rockwell Automation sales representative.
Rockwell Automation Support
For technical support, visit http://www.rockwellautomation.com/support/
overview.page.
Resource Description
Stratix Ethernet Device Specifications Technical
Data, publication 1783-TD001
Provides specification information for the switches.
EtherNet/IP Industrial Protocol White Paper,
publication ENET-WP001
Describes how to implement services and data
objects on a TCP/UDP/IP based Ethernet network.
Stratix 6000 Ethernet Managed Switch User Manual,
publication 1783-UM001
Describes how to configure and use the switch.
Industrial Automation Wiring and Grounding
Guidelines, publication 1770-4.1
Provides general guidelines for installing a Rockwell
Automation industrial system.
Product Certifications website,
http://www.rockwellautomation.com/global/
certification/overview.page
Provides declarations of conformity, certificates, and
other certification details.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Allen-Bradley 1783-EMS04T Installation Instructions Manual

Marque
Allen-Bradley
Modèle
1783-EMS04T
Catégorie
Convertisseurs de média réseau
Taper
Installation Instructions Manual
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents