Allen-Bradley Compact 5000 Installation Instructions Manual

Marque: Allen-Bradley

Modèle: Compact 5000

Taper: Installation Instructions Manual

Installation Instructions

Original Instructions

Compact 5000 I/O Analog 8-channel Current/Voltage Input

Module

Catalog Number 5069-IF8

The 5069-IF8 analog 8-channel current/voltage input module offers differential, non-isolated input channels that can connect to current or voltage

input devices. The module supports multiple ranges for each input type.Differential inputs have greater resistance to the effects of electromagnetic

noise in a control system.

Compact 5000 I/O™ modules use the Producer/Consumer communication model. The Producer/Consumer communication model is an

intelligent data exchange between module and other system devices in which each module produces data without first being polled.

For more information on how to use Compact 5000 I/O modules, see the publications that are listed in Additional Resources on page 14.

Summary of Changes

The following changes were made to this revision of this publication.

Topic Page

Module Overview 5

Install a System 5

Install the Removable Terminal Block 7

Install the Module 7

Install the End Cap 8

Wire the Removable Terminal Block 9

Disconnect Wires from the Removable Terminal Block 9

Wiring Diagram 10

Use a Cable Tie 12

Power the System 12

Remove the Module 12

Specifications 13

Additional Resources 14

Topic Page(s)

Updated graphics that shows the lower hook that can be used with a cable tie 5, 5, and 10

New module height dimension 5

Additional information about how to install an end cap 8

Additional information in the wiring diagram 10

Description of how to use the cable tie on the module 12

Updates to module specifications 13

2 Rockwell Automation Publication 5069-IN010B-EN-P - November 2017

COMPACT 5000 Analog 8-channel Current/Voltage Input Module

ATTENTION: Read this document and the documents listed in the Additional Resources section about installation, configuration and operation of this equipment before you install, configure, operate or maintain

this product. Users are required to familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards.

Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to be carried out by suitably trained personnel in accordance with applicable code of

practice.

If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.

⌘᜿˖൘ᆹ㻵ǃ䝽㖞ǃ᫽֌઼㔤ᣔᵜӗ૱ࡽˈ䈧䰵䈫ᵜ᮷ẓԕ৺ Ā ަԆ䍴Ⓚ ā 䜘࠶ࡇࠪⲴᴹޣ䇮༷ᆹ㻵ǃ䝽㖞઼᫽֌Ⲵ⴨ᓄ᮷ẓǄ䲔Ҷᡰᴹ䘲⭘㿴㤳ǃ⌅ᖻ

઼ḷ߶Ⲵ⴨ޣ㾱≲ѻཆˈ⭘ᡧ䘈ᗵ享⟏ᚹᆹ㻵઼᧕㓯䈤᰾Ǆ

ᆹ㻵ǃ䈳ᮤǃᣅ䘀ǃ֯⭘ǃ㓴㻵ǃ᣶ন઼㔤ᣔㅹ਴亩᫽֌ᗵ享⭡㓿䗷䘲ᖃ䇝㓳ⲴуъӪઈ᤹➗䘲⭘Ⲵ᫽֌㿴㤳ᇎᯭǄ

ྲ᷌ᵚ᤹➗ࡦ䙐୶ᤷᇊⲴᯩᔿ֯⭘䈕䇮༷ˈࡉਟ㜭Պᦏᇣ䇮༷ᨀ׋Ⲵ؍ᣔǄ

ATENCIÓN: Antes de instalar, configurar, poner en funcionamiento o realizar el mantenimiento de este producto, lea este documento y los documentos listados en la sección Recursos adicionales acerca de la

instalación, configuración y operación de este equipo. Los usuarios deben familiarizarse con las instrucciones de instalación y cableado y con los requisitos de todos los códigos, leyes y estándares vigentes.

El personal debidamente capacitado debe realizar las actividades relacionadas a la instalación, ajustes, puesta en servicio, uso, ensamblaje, desensamblaje y mantenimiento de conformidad con el código de

práctica aplicable.

Si este equipo se usa de una manera no especificada por el fabricante, la protección provista por el equipo puede resultar afectada.

ATENÇÃO: Leia este e os demais documentos sobre instalação, configuração e operação do equipamento que estão na seção Recursos adicionais antes de instalar, configurar, operar ou manter este produto. Os

usuários devem se familiarizar com as instruções de instalação e fiação além das especificações para todos os códigos, leis e normas aplicáveis.

É necessário que as atividades, incluindo instalação, ajustes, colocação em serviço, utilização, montagem, desmontagem e manutenção sejam realizadas por pessoal qualificado e especializado, de acordo com o

código de prática aplicável.

Caso este equipamento seja utilizado de maneira não estabelecida pelo fabricante, a proteção fornecida pelo equipamento pode ficar prejudicada.

ВНИМАНИЕ: Перед тем как устанавливать, настраивать, эксплуатировать или обслуживать данное оборудование, прочитайте этот документ и документы, перечисленные в разделе

«Дополнительные ресурсы». В этих документах изложены сведения об установке, настройке и эксплуатации данного оборудования. Пользователи обязаны ознакомиться с инструкциями по

установке и прокладке соединений, а также с требованиями всех применимых норм, законов и стандартов.

Все действия, включая установку, наладку, ввод в эксплуатацию, использование, сборку, разборку и техническое обслуживание, должны выполняться обученным персоналом в соответствии с

применимыми нормами и правилами.

Если оборудование используется не предусмотренным производителем образом, защита оборудования может быть нарушена.

ὀព ᮏ〇ရࢆタ⨨ࠊᵓᡂࠊ✌ືࡲࡓࡣಖᏲࡍࡿ๓࡟ࠊᮏ᭩࠾ࡼࡧᮏᶵჾࡢタ⨨ࠊタᐃࠊ᧯స࡟ࡘ࠸࡚ࡢཧ⪃㈨ᩱࡢヱᙜ⟠ᡤ࡟グ㍕ࡉࢀ࡚࠸ࡿᩥ᭩࡟┠ࢆ

㏻ࡋ࡚ࡃࡔࡉ࠸ࠋ࣮ࣘࢨࡣࠊࡍ࡭࡚ࡢヱᙜࡍࡿ᮲౛ࠊἲᚊࠊつ᱁ࡢせ௳࡟ຍ࠼࡚ࠊタ⨨࠾ࡼࡧ㓄⥺ࡢᡭ㡰࡟⩦⇍ࡋ࡚࠸ࡿᚲせࡀ࠶ࡾࡲࡍࠋ

タ⨨ㄪᩚࠊ㐠㌿ࡢ㛤ጞࠊ౑⏝ࠊ⤌❧࡚ࠊゎయࠊಖᏲࢆྵࡴㅖసᴗࡣࠊヱᙜࡍࡿᐇ᪋つ๎࡟ᚑࡗ࡚カ⦎ࢆཷࡅࡓ㐺ษ࡞సᴗဨࡀᐇ⾜ࡍࡿᚲせࡀ࠶ࡾࡲࡍࠋ

ᮏᶵჾࡀ〇㐀࣓࣮࢝࡟ࡼࡾᣦᐃࡉࢀ࡚࠸࡞࠸᪉ἲ࡛౑⏝ࡉࢀ࡚࠸ࡿሙྜࠊᶵჾ࡟ࡼࡾᥦ౪ࡉࢀ࡚࠸ࡿಖㆤࡀᦆ࡞ࢃࢀࡿᜍࢀࡀ࠶ࡾࡲࡍࠋ

ACHTUNG: Lesen Sie dieses Dokument und die im Abschnitt „Weitere Informationen“aufgeführten Dokumente, die Informationen zu Installation, Konfiguration und Bedienung dieses Produkts enthalten, bevor

Sie dieses Produkt installieren, konfigurieren, bedienen oder warten. Anwender müssen sich neben den Bestimmungen aller anwendbaren Vorschriften, Gesetze und Normen zusätzlich mit den Installations- und

Verdrahtungsanweisungen vertraut machen.

Arbeiten im Rahmen der Installation, Anpassung, Inbetriebnahme, Verwendung, Montage, Demontage oder Instandhaltung dürfen nur durch ausreichend geschulte Mitarbeiter und in Übereinstimmung mit den

anwendbaren Ausführungsvorschriften vorgenommen werden.

Wenn das Gerät in einer Weise verwendet wird, die vom Hersteller nicht vorgesehen ist, kann die Schutzfunktion beeinträchtigt sein.

ATTENTION : Lisez ce document et les documents listés dans la section Ressources complémentaires relatifs à l’installation, la configuration et le fonctionnement de cet équipement avant d’installer, configurer,

utiliser ou entretenir ce produit. Les utilisateurs doivent se familiariser avec les instructions d’installation et de câblage en plus des exigences relatives aux codes, lois et normes en vigueur.

Les activités relatives à l’installation, le réglage, la mise en service, l’utilisation, l’assemblage, le démontage et l’entretien doivent être réalisées par des personnes formées selon le code de pratique en vigueur.

Si cet équipement est utilisé d’une façon qui n’a pas été définie par le fabricant, la protection fournie par l’équipement peut être compromise.

㭒㦮 a ⽎G㩲䛞G㍺䂮 SG㍺㩫 SG㧧☯G⡦⓪G㥶㰖G⽊㑮䞮₆G㩚㠦G⽎Gⶎ㍲⯒G䙂䞾䞮㡂G㍺䂮 SG㍺㩫G⹥G㧧☯㠦Gὖ䞲G㺎ἶG㧦⬢G㎏㎮㦮Gⶎ㍲✺㦚G⹮✲㔲G㧓ἶG㑯㰖䞮㕃

㔲㡺 UG㌂㣿㧦⓪G⳾✶Gὖ⩾G′㩫 SG⻫′G⹥G䚲㭖㠦㍲G㣪ῂ䞮⓪G㌂䟃㠦G╖䟊G⹮✲㔲G㍺䂮G⹥G⺆㍶G㰖䂾㦚G㑯㰖䟊㟒G䞿┞┺ U

㍺䂮 SG㫆㩫 SGṖ☯ SG㌂㣿 SG㫆Ⱃ SG⿚䟊 SG㥶㰖⽊㑮G❇G⳾✶G㧧㠛㦖Gὖ⩾G′㩫㠦G➆⧒G㩗㩞䞲Gᾦ㥷㦚G⹱㦖G㌂㣿㧦⯒G䐋䟊㍲ⰢG㑮䟟䟊㟒G䞿┞┺ U

⽎G㧻゚⯒G㩲㫆㌂ṖGⳛ㔲䞮㰖G㞠㦖G⹿⻫㦒⪲G㌂㣿䞮ⳊG㧻゚㦮G⽊䢎G₆⓻㧊G㏦㌗♶G㑮G㧞㔋┞┺ U

ATTENZIONE Prima di installare, configurare ed utilizzare il prodotto, o effettuare interventi di manutenzione su di esso, leggere il presente documento ed i documenti elencati nella sezione “Altre risorse”,

riguardanti l’installazione, la configurazione ed il funzionamento dell’apparecchiatura. Gli utenti devono leggere e comprendere le istruzioni di installazione e cablaggio, oltre ai requisiti previsti dalle leggi, codici

e standard applicabili.

Le attività come installazione, regolazioni, utilizzo, assemblaggio, disassemblaggio e manutenzione devono essere svolte da personale adeguatamente addestrato, nel rispetto delle procedure previste.

Qualora l’apparecchio venga utilizzato con modalità diverse da quanto previsto dal produttore, la sua funzione di protezione potrebbe venire compromessa.

DİKKAT: Bu ürünün kurulumu, yapılandırılması, işletilmesi veya bakımı öncesinde bu dokümanı ve bu ekipmanın kurulumu, yapılandırılması ve işletimi ile ilgili İlave Kaynaklar bölümünde yer listelenmiş

dokümanları okuyun. Kullanıcılar yürürlükteki tüm yönetmelikler, yasalar ve standartların gereksinimlerine ek olarak kurulum ve kablolama talimatlarını da öğrenmek zorundadır.

Kurulum, ayarlama, hizmete alma, kullanma, parçaları birleştirme, parçaları sökme ve bakım gibi aktiviteler sadece uygun eğitimleri almış kişiler tarafından yürürlükteki uygulama yönetmeliklerine uygun şekilde

yapılabilir.

Bu ekipman üretici tarafından belirlenmiş amacın dışında kullanılırsa, ekipman tarafından sağlanan koruma bozulabilir.

⌘᜿һ丵˖൘ᆹ㼍ǃ䁝ᇊǃ᫽֌ᡆ㏝䆧ᵜ⭒૱ࡽˈ䃻ݸ䯡䆰↔᮷Ԧԕ৺ࡇᯬ ǋަԆ䋷Ⓚǌㄐㇰѝᴹ䰌ᆹ㼍ǃ䁝ᇊ㠷᫽֌↔䁝ۉⲴ᮷ԦǄ֯⭘㘵ᗵ丸⟏ᚹᆹ㼍઼

䝽㐊ᤷ⽪ˈіㅖਸᡰᴹ⌅㾿ǃ⌅ᖻ઼⁉Ⓠ㾱≲Ǆ

वᤜᆹ㼍ǃ䃯ᮤǃӔԈ֯⭘ǃ֯⭘ǃ㍴㼍ǃ᣶ন઼㏝䆧ㅹअ֌䜭ᗵ丸Ӕ⭡ᐢ㏃䙾䚙⮦䁃㐤ⲴӪ଑䙢㹼ˈԕㅖਸ䚙⭘Ⲵሖ֌⌅㾿Ǆ

ྲ᷌ሷ䁝ۉ⭘ᯬ䶎㼭䙐୶ᤷᇊⲴ⭘䙄ᱲˈਟ㜭ᴳ䙐ᡀ䁝ۉᡰᨀ׋Ⲵ؍䆧࣏㜭ਇᨽǄ

POZOR: Než začnete instalovat, konfigurovat či provozovat tento výrobek nebo provádět jeho údržbu, přečtěte si tento dokument a dokumenty uvedené v části Dodatečné zdroje ohledně instalace, konfigurace

a provozu tohoto zařízení. Uživatelé se musejí vedle požadavků všech relevantních vyhlášek, zákonů a norem nutně seznámit také s pokyny pro instalaci a elektrické zapojení.

Činnosti zahrnující instalaci, nastavení, uvedení do provozu, užívání, montáž, demontáž a údržbu musí vykonávat vhodně proškolený personál v souladu s příslušnými prováděcími předpisy.

Pokud se toto zařízení používá způsobem neodpovídajícím specifikaci výrobce, může být narušena ochrana, kterou toto zařízení poskytuje.

UWAGA: Przed instalacją, konfiguracją, użytkowaniem lub konserwacją tego produktu należy przeczytać niniejszy dokument oraz wszystkie dokumenty wymienione w sekcji Dodatkowe źródła omawiające

instalację, konfigurację i procedury użytkowania tego urządzenia. Użytkownicy mają obowiązek zapoznać się z instrukcjami dotyczącymi instalacji oraz oprzewodowania, jak również z obowiązującymi kodeksami,

prawem i normami.

Działania obejmujące instalację, regulację, przekazanie do użytkowania, użytkowanie, montaż, demontaż oraz konserwację muszą być wykonywane przez odpowiednio przeszkolony personel zgodnie z

obowiązującym kodeksem postępowania.

Jeśli urządzenie jest użytkowane w sposób inny niż określony przez producenta, zabezpieczenie zapewniane przez urządzenie może zostać ograniczone.

OBS! Läs detta dokument samt dokumentet, som står listat i avsnittet Övriga resurser, om installation, konfigurering och drift av denna utrustning innan du installerar, konfigurerar eller börjar använda eller

utföra underhållsarbete på produkten. Användare måste bekanta sig med instruktioner för installation och kabeldragning, förutom krav enligt gällande koder, lagar och standarder.

Åtgärder som installation, justering, service, användning, montering, demontering och underhållsarbete måste utföras av personal med lämplig utbildning enligt lämpligt bruk.

Om denna utrustning används på ett sätt som inte anges av tillverkaren kan det hända att utrustningens skyddsanordningar försätts ur funktion.

LET OP: Lees dit document en de documenten die genoemd worden in de paragraaf Aanvullende informatie over de installatie, configuratie en bediening van deze apparatuur voordat u dit product installeert,

configureert, bediend of onderhoudt. Gebruikers moeten zich vertrouwd maken met de installatie en de bedradingsinstructies, naast de vereisten van alle toepasselijke regels, wetten en normen.

Activiteiten zoals het installeren, afstellen, in gebruik stellen, gebruiken, monteren, demonteren en het uitvoeren van onderhoud mogen uitsluitend worden uitgevoerd door hiervoor opgeleid personeel en in

overeenstemming met de geldende praktijkregels.

Indien de apparatuur wordt gebruikt op een wijze die niet is gespecificeerd door de fabrikant, dan bestaat het gevaar dat de beveiliging van de apparatuur niet goed werkt.

Rockwell Automation Publication 5069-IN010B-EN-P - November 2017 3

COMPACT 5000 Analog 8-channel Current/Voltage Input Module

Waste Electrical and Electronic Equipment (WEEE)

At the end of its life, this equipment should be collected separately from any unsorted municipal waste.

Environment and Enclosure

ATTENTION: This equipment is intended for use in a Pollution Degree 2 industrial environment, in overvoltage Category II applications

(as defined in IEC 60664-1), at altitudes up to 2000 m (6562 ft) without derating.

This equipment is not intended for use in residential environments and may not provide adequate protection to radio communication services in such

environments.

This equipment is supplied as open-type equipment for indoor use. It must be mounted within an enclosure that is suitably designed for those specific

environmental conditions that will be present and appropriately designed to prevent personal injury resulting from accessibility to live parts. The enclosure must

have suitable flame-retardant properties to prevent or minimize the spread of flame, complying with a flame spread rating of 5VA or be approved for the

application if nonmetallic. The interior of the enclosure must be accessible only by the use of a tool. Subsequent sections of this publication may contain more

information regarding specific enclosure type ratings that are required to comply with certain product safety certifications.

In addition to this publication, see the following:

• Industrial Automation Wiring and Grounding Guidelines, publication

1770-4.1, for more installation requirements.

• NEMA Standard 250 and EN/IEC 60529, as applicable, for explanations of the degrees of protection provided by enclosures.

North American Hazardous Location Approval

The following information applies when operating this equipment in

hazardous locations.

Informations sur l’utilisation de cet équipement en environnements

dangereux.

Products marked "CL I, DIV 2, GP A, B, C, D" are suitable for use in Class I Division 2

Groups A, B, C, D, Hazardous Locations and nonhazardous locations only. Each product

is supplied with markings on the rating nameplate indicating the hazardous location

temperature code. When combining products within a system, the most adverse

temperature code (lowest "T" number) may be used to help determine the overall

temperature code of the system. Combinations of equipment in your system are

subject to investigation by the local Authority Having Jurisdiction at the time of

installation.

Les produits marqués "CL I, DIV 2, GP A, B, C, D" ne conviennent qu'à une utilisation en

environnements de Classe I Division 2 Groupes A, B, C, D dangereux et non dangereux.

Chaque produit est livré avec des marquages sur sa plaque d'identification qui indiquent

le code de température pour les environnements dangereux. Lorsque plusieurs produits

sont combinés dans un système, le code de température le plus défavorable (code de

température le plus faible) peut être utilisé pour déterminer le code de température

global du système. Les combinaisons d'équipements dans le système sont sujettes à

inspection par les autorités locales qualifiées au moment de l'installation.

WARNING:

Explosion Hazard –

• Do not disconnect equipment unless power has been removed

or the area is known to be nonhazardous.

• Do not disconnect connections to this equipment unless power

has been removed or the area is known to be nonhazardous.

Secure any external connections that mate to this equipment by

using screws, sliding latches, threaded connectors, or other

means provided with this product.

• Substitution of components may impair suitability for Class I,

Division 2.

• If this product contains batteries, they must only be changed in

an area known to be nonhazardous.

AVERTISSEMENT:

Risque d’Explosion –

• Couper le courant ou s'assurer que l'environnement est classé non

dangereux avant de débrancher l'équipement.

• Couper le courant ou s'assurer que l'environnement est classé non

dangereux avant de débrancher les connecteurs. Fixer tous les

connecteurs externes reliés à cet équipement à l'aide de vis, loquets

coulissants, connecteurs filetés ou autres moyens fournis avec ce

produit.

• La substitution de composants peut rendre cet équipement

inadapté à une utilisation en environnement de Classe I, Division 2.

• S'assurer que l'environnement est classé non dangereux avant de

changer les piles.

European Hazardous Location Approval

The following applies to products marked , II 3 G. Such modules:

• Are Equipment Group II, Equipment Category 3, and comply with the Essential Health and Safety Requirements relating to the design and construction of such equipment given in Annex II to Directive

94/9/EC. See the EC Declaration of Conformity at http://www.rockwellautomation.com/products/certification for details.

• The type of protection is "Ex nA IIC T4 Gc" according to EN 60079-15.

• The 5069-IF8 module complies to standards: EN 60079-0:2012+A11:2013, EN 60079-15:2010, reference certificate number DEMKO 15 ATEX 1484X.

• Are intended for use in areas in which explosive atmospheres caused by gases, vapors, mists, or air are unlikely to occur, or are likely to occur only infrequently and for short periods. Such locations

correspond to Zone 2 classification according to ATEX directive 1999/92/EC.

4 Rockwell Automation Publication 5069-IN010B-EN-P - November 2017

COMPACT 5000 Analog 8-channel Current/Voltage Input Module

IEC Hazardous Location Approval

The following applies to products with IECEx certification: Such modules:

correspond to Zone 2 classification to IEC 60079-0.

• The type of protection is "Ex nA IIC T4 Gc" according to IEC 60079-15.

• The 5069-IF8 module complies to standards IEC 60079-0:6th Edition, IEC-60079-15:4th Edition, reference IECEx certificate number IECEx UL 15.0055X.

Special Conditions for Safe Use

WARNING:

• This equipment is not resistant to sunlight or other sources of UV radiation.

• This equipment shall be mounted in an ATEX/IECEx Zone 2 certified enclosure with a minimum ingress protection rating of at least IP54 (as defined in

EN/IEC 60529) and used in an environment of not more than Pollution Degree 2 (as defined in EN/IEC 60664-1) when applied in Zone 2 environments. The

enclosure must be accessible only by the use of a tool.

• This equipment shall be used within its specified ratings defined by Rockwell Automation.

• Provision shall be made to prevent the rated voltage from being exceeded by transient disturbances of more than 140% of the rated voltage when applied in

Zone 2 environments.

• The instructions in the user manual shall be observed.

• This equipment must be used only with ATEX/IECEx certified Rockwell Automation backplanes.

• Secure any external connections that mate to this equipment by using screws, sliding latches, threaded connectors, or other means provided with this

product.

• Do not disconnect equipment unless power has been removed or the area is known to be nonhazardous.

• Earthing is accomplished through mounting of modules on rail.

• Devices shall be used in an environment of not more than Pollution Degree 2.

Prevent Electrostatic Discharge

ATTENTION: This equipment is sensitive to electrostatic discharge, which can cause internal damage and affect normal operation. Follow these guidelines when

you handle this equipment:

• Touch a grounded object to discharge potential static.

• Wear an approved grounding wriststrap.

• Do not touch connectors or pins on component boards.

• Do not touch circuit components inside the equipment.

• Use a static-safe workstation, if available.

• Store the equipment in appropriate static-safe packaging when not in use.

Electrical Safety Considerations

ATTENTION:

• Do not wire more than 1 conductor on any single RTB terminal.

• In case of malfunction or damage, no attempts at repair should be made. The module should be returned to the manufacturer for repair. Do not dismantle

the module.

• This equipment is certified for use only within the surrounding air temperature range of 0…60 °C (32…140 °F) The equipment must not be used outside of

this range.

• Use only a soft dry anti-static cloth to wipe down equipment. Do not use any cleaning agents.

IMPORTANT Any illustrations, charts, sample programs, and layout examples shown in this publication are intended solely for the purposes of example. Since there are

many variables and requirements associated with any particular installation, Rockwell Automation does not assume responsibility or liability for actual use

based upon the examples shown in this publication.

Rockwell Automation Publication 5069-IN010B-EN-P - November 2017 5

COMPACT 5000 Analog 8-channel Current/Voltage Input Module

Module Overview Install a System

Based on your application design, you must install a

CompactLogix 5380 controller or Compact 5000 I/O EtherNet/IP

adapter before you can install the module.

For more information on how to install these components, see

Additional Resources on page 14.

Required Components

To install the module, you need these components.

ANALOG INPUT

5069-IF8

Module Status Indicator

I/O Status Indicator

Top Interlocking Piece

Bottom Interlocking Piece

DIN Rail Latch

RTB Handle

RTB

MOD Power Bus

and SA Power Bus

Connectors

(isolated from each

other internally)

RTB Lower Tab

Lower hook for use

with cable tie.

Component Description

Removable

terminal blocks

One of the following RTB types.

• 5069-RTB18-SPRING RTB

• 5069-RTB18-SCREW RTB

IMPORTANT: You must order RTBs separately. RTBs do not ship with

Compact 5000 I/O modules. We recommend that you order only the RTB

type that your system requires.

End cap

An end cap ships with the CompactLogix 5380 controllers and the

Compact 5000 I/O EtherNet/IP adapters.

Tools

The following tools are needed:

• Screwdriver

• Wire stripper

• Wires

For more information on available wire sizes and wire insulation stripping

length, see

Specifications on page 13.

6 Rockwell Automation Publication 5069-IN010B-EN-P - November 2017

COMPACT 5000 Analog 8-channel Current/Voltage Input Module

Dimensions Ground Considerations

You must ground DIN rails according to the Industrial Automation

Wiring and Grounding Guidelines, publication

1770-4.1.

You can use the EN50022 - 35 x 7.5 mm (1.38 x 0.30 in.) DIN rail

with Compact 5000 I/O modules.

System Power Considerations

A CompactLogix 5380 controller or Compact 5000 I/O EtherNet/IP

adapter provides power to the module.

The following power types are available:

• Module (MOD) power - System-side power that is required to

operate the Compact 5000 I/O modules. MOD power is

provided through the MOD power RTB and passed across the

MOD power bus.

• Sensor/Actuator (SA) power - Field-side power that is used to

power field-side devices. SA power is provided through the SA

power RTB and passed across the SA power bus.

The first component in the system, that is, the controller or the

adapter, establishes an SA power bus.

A system can have more than one SA power bus. You use

5069-FPD field potential distributors to establish a new SA

power bus. SA power buses are isolated from each other.

If a system includes Compact 5000 I/O modules that use AC

SA power and modules that use DC SA power, you must

install them on separate SA power buses.

ANALOG INPUT

5069-IF8

109.09 mm (4.29 in.)

25.56 mm (1.01 in.)

144.57 mm

(5.69 in.)

105.42 mm (4.15 in.)

22 mm (0.87 in.)

ATTENTION: This product is grounded through the DIN rail to

chassis ground. Use zinc-plated chromate-passivated steel DIN

rail to assure proper grounding. The use of other DIN rail

materials (for example, aluminum or plastic) that can corrode,

oxidize, or are poor conductors, can result in improper or

intermittent grounding. Secure DIN rail to mounting surface

approximately every 200 mm (7.8 in.) and use end-anchors

appropriately. Be sure to ground the DIN rail properly. Refer to

Industrial Automation Wiring and Grounding Guidelines,

Rockwell Automation® publication

1770-4.1 for more

information.

Rockwell Automation Publication 5069-IN010B-EN-P - November 2017 7

COMPACT 5000 Analog 8-channel Current/Voltage Input Module

To keep the modules on separate SA power buses, complete the

following steps.

a. Install the modules that use one type of SA power, for

example AC, to the right of the adapter or controller, that

is, the first SA power bus.

b. Install the 5069-FPD field potential distributor to establish

a second SA power bus.

c. Install the modules that use the other type of SA power, for

example DC, on the second SA power bus.

Install the Removable Terminal Block

1. Hook the bottom of the RTB on the module.

2. Push the RTB against the module until the RTB clicks

into place.

3. Push the RTB handle against the RTB until you hear

another click.

Install the Module

Install the I/O module next to the right-most device in the system. To

install the module, complete these steps.

1. Confirm that MOD power and all sources of SA power are off.

If you remove the module with power applied, the system

MOD power bus and SA power bus are affected. For example,

you can interrupt MOD power to the other modules in the

system. Unintended consequences can occur as a result.

2. If an end cap is installed on the right-most module that is

installed in the system, remove it and keep for later use.

3. Confirm that the DIN rail latch is closed.

4. If the DIN rail latches are open, gently push the rear latch back

until the front latch pops up and clicks.

ATTENTION: To reduce susceptibility to noise, power

analog modules and digital modules from separate

power supplies.

IMPORTANT We recommend that you use separate external power supplies

for MOD power and SA power respectively. This practice helps

to prevent unintended consequences that can result if you use

one supply.

If you use separate external power supplies, the loss of power

from one external power supply does not affect the

availability of power from the other supply. For example, if

separate external power supplies are used and SA power is

lost, MOD power remains available for the Compact 5000 I/O

modules.

WARNING: If you connect or disconnect the removable terminal

block (RTB) with power applied, an electric arc can occur. This

could cause an explosion in hazardous location installations.

The removable terminal block (RTB) does not support "Removal

and Insertion Under Power" (RIUP) capability. Do not connect or

disconnect the removable terminal block (RTB) while power is

applied. Be sure that power is removed before proceeding.

WARNING: If you insert or remove the module while backplane

power is on, an electric arc can occur. This could cause an explosion

in hazardous location installations.

The module does not support "Removal and Insertion Under

Power" (RIUP) capability. Do not connect or disconnect the

module while power is applied. Be sure that power is removed

before proceeding.

ATTENTION: Do not discard the end cap. Use this end

cap to cover the exposed interconnections on the last

module on the DIN rail. Failure to do so could result in

equipment damage or injury from electric shock.

Open PositionClosed Position

8 Rockwell Automation Publication 5069-IN010B-EN-P - November 2017

COMPACT 5000 Analog 8-channel Current/Voltage Input Module

5. Align the interlocking pieces of the module with the device on

the left.

The top interlocking pieces engage first.

6. Push the module toward the DIN rail until a click indicates

that the module is locked in place.

7. Verify that the module is installed in one of the following ways:

• If the module is installed next to a controller or adapter, the

front of the module is set back slightly from the front of the

controller or adapter.

• If the module is installed next to another I/O module, the

fronts of both modules are flush with each other.

Install the End Cap

You must install an end cap on the last module in your system.

1. Align the end cap with the interlocking pieces on the module.

2. Push the end cap toward the DIN rail until it locks in place.

ADAPTER

Top

Interlocking

Pieces

Bottom

Interlocking

Piece

IMPORTANT You install the end cap after the last module is installed on

the DIN rail. This design helps to prevent the end cap from

going beyond the locked position.

If you push the end cap beyond the locked position or insert it

from the backwards direction, you can damage the MOD

power bus and SA power bus connector.

ADAPTER

Interlocking

Pieces

End Cap

Rockwell Automation Publication 5069-IN010B-EN-P - November 2017 9

COMPACT 5000 Analog 8-channel Current/Voltage Input Module

Wire the Removable Terminal Block

1. Confirm that MOD power and all sources of SA power are

turned off.

2. Strip insulation from the wires that you connect to the RTB.

3. Connect the wire to the terminal.

Disconnect Wires from the Removable Terminal Block

Disconnect wires from the RTB.

WARNING: If you connect or disconnect wiring while power is

applied, an electric arc can occur. This could cause an explosion in

hazardous location installations. Be sure that power is removed or

the area is nonhazardous before proceeding.

RTB Type Action

Screw Strip12 mm (0.47 in.) of insulation from the wires.

Spring Strip 10 mm (0.39 in.) of insulation from the wires.

RTB Type Action

Screw

1. Insert the wire into the terminal.

2. Turn the screwdriver to close the terminal on the wire. Torque the

screw to 0.4 N•m (3.5 lb•in).

Spring

Push the wire into the terminal.

If the wire is too thin, crimp a wire ferrule on the wire and insert it.

5069-RTB18-SPRING RTB5069-RTB18-SCREW RTB

WARNING: If you connect or disconnect wiring while power is

applied, an electric arc can occur. This could cause an explosion in

hazardous location installations. Be sure that power is removed or

the area is nonhazardous before proceeding.

RTB Type Action

Screw

1. Turn the screwdriver counter-clockwise to open the terminal.

2. Remove the wire.

Spring

1. Insert and hold a screwdriver in the right-side terminal.

2. Remove the wire.

3. Pull out the screwdriver.

5069-RTB18-SCREW RTB

5069-RTB18-SPRING RTB

10 Rockwell Automation Publication 5069-IN010B-EN-P - November 2017

COMPACT 5000 Analog 8-channel Current/Voltage Input Module

Wiring Diagram

The following is an example wiring diagram for the 5069-IF8 analog input module in current mode.

ANALOG INPUT

5069-IF8

Input 0 +

Input 0 -

Input 1 +

Input 1 -

Input 2 +

Input 2 -

Input 3 +

Input 3 -

Input 4 +

Input 4 -

Input 5 +

Input 5 -

Input 6 +

Input 6 -

Input 7 +

Input 7 -

Shield

2-wire

Transmitter

24V DC

–

Shield

Ground

IMPORTANT: Place additional loop devices, for

example, strip chart recorders, at either A

location in the current loop.

Channel Connections

The diagram shows a device that is connected to

channel 0. You are not restricted to using only

this channel.

You can connect devices to any channel or

combination of channels as needed.

Rockwell Automation Publication 5069-IN010B-EN-P - November 2017 11

COMPACT 5000 Analog 8-channel Current/Voltage Input Module

The following is an example wiring diagram for the 5069-IF8 analog input module in voltage mode.

ANALOG INPUT

5069-IF8

Input 0 +

Input 0 -

Input 1 +

Input 1 -

Input 2 +

Input 2 -

Input 3 +

Input 3 -

Input 4 +

Input 4 -

Input 5 +

Input 5 -

Input 6 +

Input 6 -

Input 7 +

Input 7 -

Shield

User Analog

Input Device

24V DC

–

Shield

Ground

Channel Connections

The diagram shows a device that is connected to

channel 0. You are not restricted to using only

this channel.

You can connect devices to any channel or

combination of channels as needed.

12 Rockwell Automation Publication 5069-IN010B-EN-P - November 2017

COMPACT 5000 Analog 8-channel Current/Voltage Input Module

Use a Cable Tie

After you connect the required wires to the RTB, you can use a cable

tie to bundle the wires. There is a lower hook at the bottom of the

module that you use to secure the tied bundle to the module.

1. Make sure that you have a cable tie long enough to contain the

wires that are connected to the module.

The maximum width of the cable tie is 4.5 mm (0.18 in).

2. Gather the wires at the bottom of the module.

3. Thread the cable tie through the lower hook at the bottom of

the RTB..

4. Wrap the cable tie around the wires and secure it.

Power the System

After you install all Compact 5000 I/O modules, you can turn on

MOD power and, if used, SA power to the system.

For more information on MOD power and SA power, see

System

Power Considerations on page 6.

Remove the Module

1. Confirm that MOD power and all sources of SA power are

turned off.

2. If necessary, remove the end cap from the right side of the

module.

3. If desired, disconnect wires from the RTB as described on

page 9.

4. Press the DIN rail latch down until it clicks and let go of the

latch.

5. Pull the module off the DIN rail.

6. To replace the module, follow the steps that are described

beginning at

Install the Module on page 7.

ATTENTION: Do not remove or replace the module while power is

applied. Interruption of the backplane can result in unintentional

operation or machine motion.

IMPORTANT Before you remove power from the MOD power RTB

and, if used, SA power RTB, consider the effect on

your system.

When you remove MOD power and SA power from a

controller or adapter, you shut down power to all

Compact 5000 I/O modules in the system. That is, all

system-side and field-side power is removed.

We strongly recommend that you take the

appropriate actions to help prevent unintended

consequences that can result from a system power

shutdown before you remove MOD power and

SA power.

ADAPTER

AENTR

ADAPTER

Rockwell Automation Publication 5069-IN010B-EN-P - November 2017 13

COMPACT 5000 Analog 8-channel Current/Voltage Input Module

Specifications

This table lists a subset of the module specifications. For a list of all specifications, see the Compact 5000 I/O Modules and EtherNet/IP Adapters

Technical Data, publication

5069-TD001.

5069-IF8 Analog 8-channel Current/Voltage Input Module Specifications

Attribute Value

Temperature, operating

• IEC 60068-2-1 (Test Ad, Operating Cold),

• IEC 60068-2-2 (Test Bd, Operating Dry Heat),

• IEC 60068-2-14 (Test Nb, Operating Thermal Shock)

0…60 °C (32…140 °F)

Temperature, surrounding air, max 60 °C (140 °F)

Enclosure type rating None (open-style)

Voltage and current ratings

Analog input ratings 0…20 mA, +/–10V DC (per channel)

MOD Power 75 mA @ 18…32V DC

MOD Power (Passthrough)

(1)

(1) Maximum level of MOD Power current that the module can pass through to the next module in the system. The specific level of current passed through varies based on system configuration.

9.55 A @ 18…32V DC

SA Power 100 mA @ 18…32V DC

SA Power (Passthrough)

(2)

(2) Maximum level of SA Power current that the module can pass through to the next module in the system. The specific level of current passed through varies based on system configuration.

9.95 A @ 18…32V DC

Do not exceed 10 A MOD or SA Power (Passthrough) current draw

Isolation voltage

300V (continuous), Basic Insulation Type

50V Functional Isolation between SA power and input ports

No isolation between individual input ports

Wire size

5069-RTB18-SCREW and 5069-RTB14CJC-SCREW connections

0.5…1.5 mm

(22…16 AWG) solid or stranded shielded copper wire rated at 105 °C (221 °F), or greater,

3.5 mm (0.14 in.) max diameter including insulation, single wire connection only.

5069-RTB18-SPRING and 5069-RTB14CJC-SPRING connections

0.5…1.5 mm

(22…16 AWG) solid or stranded shielded copper wire rated at 105 °C (221 °F), or greater,

2.9 mm (0.11 in.) max diameter including insulation, single wire connection only.

Insulation stripping length

5069-RTB18-SCREW and 5069-RTB14CJC-SCREW connections 12 mm (0.47 in.)

5069-RTB18-SPRING and 5069-RTB14CJC-SPRING connections 10 mm (0.39 in.)

RTB torque specifications (5069-RTB18-SCREW RTB and 5069-RTB14CJC-SCREW RTB only) 0.4 N·m (3.5 lb·in)

North American Temp Code T4

ATEX Temp Code T4

IECEx Temp Code T4

14 Rockwell Automation Publication 5069-IN010B-EN-P - November 2017

COMPACT 5000 Analog 8-channel Current/Voltage Input Module

Additional Resources

You can view or download publications at http://www.rockwellautomation.com/global/literature-library/overview.page. To order paper copies of

technical documentation, contact your local Allen-Bradley distributor or Rockwell Automation sales representative.

Resource Description

Compact 5000 I/O Modules and EtherNet/IP Adapters Technical Data, publication

5069-TD001

Provides specifications for Compact 5000 I/O modules and EtherNet/IP adapters.

Compact 5000 I/O Analog Modules User Manual, publication 5000-UM005 Describes how to use the Compact 5000 I/O analog modules.

EtherNet/IP Communication Modules in Logix 5000 Control Systems User Manual,

publication ENET-UM004

Describes how to use Compact 5000 I/O EtherNet/IP adapters.

CompactLogix 5380 Controllers User Manual, publication 5069-UM001 Describes how to use CompactLogix 5380 controllers.

Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1 Provides general guidelines for installing a Rockwell Automation industrial system.

Product Certifications website, http://www.rockwellautomation.com/global/certification/

overview.page

Provides declarations of conformity, certificates, and other certification details.

Rockwell Automation Publication 5069-IN010B-EN-P - November 2017 15

COMPACT 5000 Analog 8-channel Current/Voltage Input Module

Notes:

Allen-Bradley, Compact 5000, CompactLogix, Rockwell Automation, Rockwell Software, and Studio 5000 Logix Designer are trademarks of Rockwell Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400

Rockwell Automation maintains current product environmental information on its website at

http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.

Publication 5069-IN010B-EN-P - November 2017 PN-469204

Rockwell Automation Support

Use the following resources to access support information.

Documentation Feedback