Maytag MFI2570FEZ Le manuel du propriétaire

Catégorie
Frigos
Taper
Le manuel du propriétaire

Ce manuel convient également à

W11468671A
FRENCH DOOR BOTTOM MOUNT OWNER’S
MANUAL
MANUEL D’UTILISATION DE RÉFRIGÉRATEUR À
PORTE À DOUBLE BATTANT ET CONGÉLATEUR EN
BAS
Table of Contents/Table des matières
REFRIGERATOR SAFETY.................................................2
Refrigerator Safety .........................................................2
REFRIGERATOR CARE ....................................................3
Cleaning ......................................................................3
Changing the LED Module ...............................................4
Refrigerator Shelves.......................................................4
Opening and Closing Doors .............................................5
Vacation and Moving Care ...............................................6
INSTALLATION INSTRUCTIONS ........................................6
Unpack the Refrigerator ..................................................6
Location Requirements ...................................................7
Electrical Requirements ..................................................7
Water Supply Requirements.............................................7
Connect the Water Supply ...............................................8
Complete the Installation ............................................... 10
Install Air Filter (on some models).................................... 10
Install Produce Preserver (on some models) ...................... 12
REFRIGERATOR FEATURES........................................... 12
Crisper Humidity Control (on some models) ....................... 12
Water and Ice Dispensers (on some models) ..................... 13
Ice Maker and Storage Bin............................................. 13
Water Filtration System ................................................. 15
DOOR AND HANDLE INSTRUCTIONS .............................. 17
Door and Drawers........................................................ 17
Remove and Replace Handles........................................ 17
Remove Doors and Hinges ............................................ 19
Reset Bottom Refrigerator Door Hinge ............................. 20
Replace Refrigerator Doors and Hinges............................ 21
Remove and Replace Refrigerator Drawer ........................ 21
Door Closing and Alignment........................................... 23
PERFORMANCE DATA SHEET ........................................ 27
SÉCURITÉ DU RÉFRIGÉRATEUR .................................... 29
Sécurité du réfrigérateur................................................ 29
ENTRETIEN DU RÉFRIGÉRATEUR................................... 30
Nettoyage .................................................................. 30
Remplacer le module à DEL........................................... 32
Tablettes du réfrigérateur............................................... 32
Ouverture et fermeture des portes ................................... 33
Précautions à prendre avant les vacances ou le
déménagement ........................................................... 33
INSTRUCTIONS D’INSTALLATION ................................... 34
Déballage du réfrigérateur ............................................. 34
Exigences d’emplacement ............................................. 35
Spécifications électriques .............................................. 35
Spécifications de l’alimentation en eau ............................. 36
Raccordement à la canalisation d’eau .............................. 36
Terminer l’installation .................................................... 39
Installer le filtre à air (sur certains modèles) ....................... 39
Installation du conservateur de produits frais (sur certains
modèles).................................................................... 40
CARACTÉRISTIQUES DU RÉFRIGÉRATEUR..................... 41
Commande d’humidité dans le bac à légumes (sur certains
modèles).................................................................... 41
Distributeur d’eau et de glaçons (sur certains modèles)........ 42
Machine à glaçons et bac d’entreposage........................... 42
Système de filtration de l’eau.......................................... 44
INSTRUCTIONS POUR LA PORTE ET LA POIGNÉE............ 46
Porte et tiroirs ............................................................. 46
Pour enlever et réinstaller les poignées............................. 47
Retrait de la porte et des charnières................................. 48
Réinitialiser la charnière inférieure du réfrigérateur.............. 50
Réinstallation des portes et charnières ............................. 51
Retrait et réinstallation du tiroir de congélation ................... 52
Fermeture et alignement des portes................................. 54
FICHE DE DONNÉES RELATIVES AU RENDEMENT ........... 58
2
REFRIGERATOR SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These
words mean:
DANGER
You can be killed or seriously injured if you don't
immediately follow instructions.
WARNING
You can be killed or seriously injured if you don’t follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions,
including the following:
Children should be supervised to ensure that they do not
play with the appliance.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory, or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their
safety.
Do not use an extension cord.
If power supply cord is damaged, it must be replaced by the
manufacturer, its service agent, or a similarly qualified
person in order to avoid a hazard.
Connect to potable water supply only.
This appliance is intended to be used in household and
similar applications such as: staff kitchen areas in shops,
offices, and other working environments; farm houses and
by clients in hotels, motels, and other residential-type
environments; bed and breakfast-type environments; and
catering and similar non-retail applications.
Do not store explosive substances such as aerosol cans
with a flammable propellant in this appliance.
Do not use replacement parts that have not been
recommended by the manufacturer (e.g., parts made at
home using a 3D printer).
Keep ventilation openings, in the appliance enclosure or in
the built-in structure, clear of obstruction.
Do not use mechanical devices or other means to
accelerate the defrosting process, other than those
recommended by the manufacturer.
Do not damage the refrigerant circuit.
Do not use electrical appliances inside the food storage
compartments of the appliance, unless they are of the type
recommended by the manufacturer.
SAVE THESE INSTRUCTIONS
Proper Disposal of Your Old Refrigerator
WARNING: Risk of child entrapment. Before you throw
away your old refrigerator or freezer:
Take off the doors.
Leave the shelves in place so that children may not easily
climb inside.
WARNING
Suffocation Hazard
Remove doors or lid from your old appliance.
Failure to do so can result in death or brain damage.
IMPORTANT: Child entrapment and suffocation
are not problems of the past. Junked or
abandoned freezers or refrigerators, are still
dangerous, even if they will sit for “just a few
days.” If you are getting rid of your old refrigerator
or freezer, please follow these instructions to help
prevent accidents.
Important information to know about disposal
of refrigerants:
Dispose of refrigerator in accordance with Federal
and Local regulations. Refrigerants must be
evacuated by a licensed, EPA certified refrigerant
technician in accordance with established
procedures.
3
REFRIGERATOR CARE
Cleaning
WARNING
Explosion Hazard
Risk of Fire or Explosion.
Flammable Refrigerant Used.
Do Not Use Mechanical Devices to Defrost Refrigerator.
Do Not Puncture Refrigerant Tubing.
Both the refrigerator and freezer sections defrost automatically.
However, clean both sections about once a month to avoid odor
buildup. Wipe up spills immediately.
IMPORTANT:
Because air circulates between all sections, any odors formed
in one section will transfer to the other. You must thoroughly
clean all sections to eliminate odors. To avoid odor transfer
and drying out of food, wrap or cover foods tightly.
Do not use abrasive or harsh cleaners such as window sprays,
scouring cleansers, flammable fluids, muriatic acid, cleaning
waxes, concentrated detergents, bleaches or cleansers
containing petroleum products on doors and cabinet, plastic
parts, interior and door liners or gaskets. Do not use paper
towels, scouring pads, or other harsh cleaning tools.
For stainless steel models, stainless steel is corrosion
resistant and not corrosion-proof. To help avoid corrosion of
your stainless steel, keep your surfaces clean by using the
following cleaning instructions.
Cleaning the Touch Screen Display on the
Dispenser Panel (on some models):
1. Make sure the refrigerator is unplugged or the power is
disconnected before wiping the screen to avoid unintentionally
changing the settings.
2. Mix a solution of mild detergent in warm water. Dampen a soft,
lint-free cloth with the solution and gently wipe the screen.
NOTE: Do not spray or wipe liquids directly onto the screen or
over-saturate the cloth.
3. Plug in refrigerator or reconnect power.
Cleaning the Interior:
IMPORTANT: Refrigerator shelves with under-shelf, LED lighting
are not dishwasher safe.
1. Unplug refrigerator or disconnect power.
2. Hand wash, rinse, and dry removable parts and interior
surfaces thoroughly. Use a clean sponge or soft cloth and a
mild detergent in warm water.
3. Plug in refrigerator or reconnect power.
Cleaning the Exterior:
IMPORTANT: Damage to smooth finish due to improper use of
cleaning products or using non-recommended cleaning products
is not covered under the warranty. Sharp or blunt instruments will
mar the finish.
1. Unplug refrigerator or disconnect power.
2. Using a clean sponge or soft cloth and a mild detergent in
warm water, wash, rinse, and thoroughly dry stainless steel
and painted metal exteriors.
To keep your stainless steel refrigerator looking like new and
to remove minor scuffs or marks, it is suggested that you use
the manufacturer’s approved stainless steel cleaner and
polish. This cleaner is for stainless steel parts only. Refer to
the Quick Start Guide for ordering information.
NOTE : When cleaning stainless steel, always wipe in the
direction of the grain to avoid cross-grain scratching.
Do not allow the stainless steel cleaner and polish to come
into contact with any plastic parts such as the trim pieces,
dispenser covers, or door gaskets. If unintentional contact
does occur, clean plastic part with a sponge and mild
detergent in warm water. Dry thoroughly with a soft cloth.
3. Plug in refrigerator or reconnect power.
Style 1: Smooth Door/Painted Metal
DO USE DO NOT USE
Soft, clean cloth Abrasive cloths
Paper towels or newsprint
Steel-wool pads
Warm, soapy water with a
mild detergent
Abrasive powders or liquids
Window sprays
Ammonia
Acidic or vinegar-based
cleaners
Oven cleaners
Flammable fluids
NOTE: Paper towels scratch and may dull the clear coat of the
painted door. To avoid possible damage, use only soft, clean
cloths to polish and wipe the door.
Style 2: Stainless Steel
DO USE DO NOT USE
Soft, clean cloth Abrasive cloths
Paper towels or newsprint
Steel-wool pads
Warm, soapy water with a
mild detergent
Abrasive powders or liquids
Ammonia
Citrus-based cleaners
Acidic or vinegar-based
cleaners
Oven cleaners
For heavy soil, use only a
manufacturer’s approved
stainless steel cleaner and
polish
Abrasive powders or liquids
Ammonia
Citrus-based cleaners
Acidic or vinegar-based
cleaners
Oven cleaners
Abrasive cloths
Paper towels or newsprint
Steel-wool pads
NOTES:
If unintentional contact does occur, clean plastic part with a
sponge and mild detergent in warm water. Dry thoroughly with
a soft cloth.
4
Avoid exposing stainless steel appliances to caustic or
corrosive elements such as high-salt, high-moisture, or high-
humidity environments. Damage due to exposure to these
elements is not covered under the warranty.
Just because a cleaner is a liquid does not mean it is
nonabrasive. Many liquid cleansers formulated to be gentle on
tile and smooth surfaces still damage stainless steel.
When cleaning stainless steel, always wipe in the direction of
the grain to avoid cross-grain scratching.
Citric acid permanently discolors stainless steel. To avoid
damaging the finish of your stainless steel refrigerator:
Do not allow these substances to remain on the finish:
Mustard
Tomato juice
Marinara sauce
Citrus-based sauces
Citrus-based products
Condenser Cleaning
WARNING
Explosion Hazard
Risk of Fire or Explosion due to Puncture of Refrigerant
Tubing;
Follow Handling Instructions Carefully.
Flammable Refrigerant Used.
There is no need for routine condenser cleaning in normal home
operating environments. If the environment is particularly greasy
or dusty or there is significant pet traffic in the home, the
condenser should be cleaned every 6 months to ensure maximum
efficiency.
1. Unplug refrigerator or disconnect power.
2. Remove the base grille.
3. Use a vacuum cleaner with a soft brush to clean the grille, the
open areas behind the grille, and the front surface area of the
condenser.
4. Replace the base grille when finished.
5. Plug in refrigerator or reconnect power.
NOTE: If you are unable to clean the condenser, please call for
service.
Changing the LED Module
IMPORTANT: The lights in both the refrigerator and freezer
compartments use LED technology that do not need to be
replaced. If the lights do not illuminate when the door or drawer is
opened, call for assistance or service. Refer to the Quick Start
Guide for contact information.
If an LED module(s) do not illuminate when the refrigerator and/or
freezer door is opened, call for assistance or service.
Refrigerator Shelves
Important information to know about glass shelves and
covers:
Do not clean glass shelves or covers with warm water when they
are cold. Shelves and covers may break if exposed to sudden
temperature changes or impact, such as bumping. Tempered
glass is designed to shatter into many small, pebble-size pieces.
This is normal. Glass shelves and covers are heavy. Use both
hands when removing them to avoid dropping.
The shelves in your refrigerator are adjustable to match your
individual storage needs.
Storing similar food items together in your refrigerator and
adjusting the shelves to fit different heights of items will make
finding the exact item you want easier. It will also reduce the
amount of time the refrigerator door is open, and save energy
Glass Shelves
To remove a shelf:
1. Remove items from the shelf.
2. Slide the shelf straight out to the stop.
3. Depending on your model, lift the back or front of the shelf
past the stop. Pull the shelf out the rest of the way.
To replace a shelf:
1. Slide the back of the shelf into the track in the wall of the
cabinet.
2. Guide the front of the shelf into the shelf track. Be sure to slide
the shelf in all the way.
Shelves with Shelf Frames
To remove and replace a shelf/shelf frame:
1. Remove the shelf/frame by tilting it up at the front and lifting it
out of the shelf supports.
2. Replace the shelf/frame by guiding the rear shelf hooks into
the shelf supports. Tilt the front of the shelf up until rear shelf
hooks drop into the shelf supports.
3. Lower the front of the shelf and make sure that the shelf is in
position.
Shelves with Under-Shelf Lighting (on some
models)
By moving LED lighting to a new spot under the shelves, this
leading-edge technology improves interior refrigerator lighting and
aids in locating storage items.
For models with the shelf frames, the hooks on the rear of the
shelf must be fully engaged in the shelf supports to maintain
proper electrical flow.
No more than two shelves with under-shelf lighting may be
used in the refrigerator at one time.
Shelves with Shelf Mounts
Shelf height can be adjusted by changing the adjustable shelf
mounts between their vertical and horizontal positions.
1. Carefully lift the shelf off the shelf mounts and turn the flipper
to the desired orientation.
5
2. Repeat for remaining shelf mounts.
3. Apply pressure to the top of the shelf to ensure the shelf is
properly seated on the shelf mounts.
To remove and replace shelves:
1. Make sure adjustable shelf mounts are in the lower position
before removing shelves. Also doors will need to be open at a
90˚ angle. If open wider, it will make it harder to remove the
shelves.
2. Remove the middle shelf or top shelf by lifting it up and out of
the shelf supports. Then pull the shelf forward and tilt down to
a vertical position. Turn the shelf at an angle and pull out of
the refrigerator.
Infinity slide glass shelves should be pushed back in. When
tilted up, make sure glass does not slide to front.
NOTE: Remove middle shelf first before removing top shelf.
3. Remove the bottom shelf by lifting it up and out of the shelf
supports. Then pull the shelf forward and tilt up to a vertical
position. Turn the shelf at an angle and pull out of the
refrigerator.
4. Replace the middle and top shelves by putting the shelf in the
refrigerator at an angle with the shelf front down. Lift the front
of the shelf up and slide in until rear shelf drops into the shelf
supports. Lower the front of the shelf and make sure that the
shelf is in position.
5. Replace the bottom shelf by putting the shelf in the refrigerator
at an angle with the shelf up. Lift the front of the shelf down
and slide in until rear shelf drops into the shelf supports.
Lower the front of the shelf and make sure that the shelf is in
position.
Tuck/Slide Away Shelf (on some models)
Some shelves will tuck/slide away to create room for taller objects.
To retract and extend the front section of the shelf:
1. To retract the front-section of the shelf, slightly lift up on the
front edge and push the adjustable portion of the shelf back
toward the rear of the refrigerator.
2. Extend the front of the shelf by pulling the retracted portion of
the shelf outward until it is fully extended.
Foldaway Shelf (on some models)
To retract the fold away shelf:
Retract the fold away section of the shelf by holding the front of
the shelf with one hand and lifting up on the center front of the
shelf. Then push back and down on the shelf until it slides
beneath the back section of the shelf.
To replace the fold away shelf:
Replace the fold away section of the shelf by holding the front of
the shelf with one hand and pulling the center of the shelf until the
fold away section is returned to its full shelf position.
MicroEdge
®®
Glo Shelves (on some models)
The hooks on the rear of the shelf must be fully engaged in the
shelf supports to maintain proper electrical flow.
No more than two shelves with under-shelf lighting may be used in
the refrigerator at one time.
Opening and Closing Doors
There are two refrigerator compartment doors. The doors can be
opened and closed either separately or together. On some
models, there is a, automatic closing mechanism so the door(s)
will not unintentionally be left open. If a door is open at a 40° or
smaller angle, the door will automatically, softly close.
IMPORTANT: If the doors do not automatically close at a 40° or
smaller angle, see “Bottom Door Hinge.”
There is a vertically-hinged seal on the left refrigerator door.
When the left-hand door is opened, the hinged seal
automatically folds inward so that it is out of the way.
When both doors are closed, the hinged seal automatically
forms a seal between the two doors.
A. Hinged seal
The refrigerator compartment door switch is located in the top left
and right hinge cover.
The door switch uses magnet to sense door opening/closing.
Ensure there are no magnet or electronic devices (Speaker,
CoolVox
®
, etc) within 3 inches of the hinge cap.
NOTE: The light and internal user interface (UI) will not turn on if
the door opening is not detected.
6
A. Hinged cover
Vacation and Moving Care
Vacation
If You Choose to Leave the Refrigerator On While You’re
Away:
1. Use up any perishables and freeze other items.
2. If your refrigerator has an automatic ice maker, and is
connected to the household water supply, turn off the water
supply to the refrigerator. Property damage can occur if the
water supply is not turned off.
3. If you have an automatic ice maker, turn off the ice maker.
NOTE: Depending on your model, raise the wire shutoff arm
to Off (up) position or press the switch to Off.
4. Empty the ice bin.
Models with Vacation Mode Feature
Turn on Vacation mode. See the “Quick Start Guide” for
details.
NOTE: Activating Vacation mode does not turn off the ice
maker.
If You Choose to Turn Off the Refrigerator Before You Leave:
1. Remove all food from the refrigerator.
2. If your refrigerator has an automatic ice maker:
Turn off the water supply to the ice maker at least one day
ahead of time.
When the last load of ice drops, raise the wire shutoff arm
to the Off (up) position or press the switch to Off,
depending on your model.
3. Empty the ice bin.
4. Turn off the Temperature control(s). See the “Quick Start
Guide.”
5. Clean refrigerator, wipe it, and dry well.
6. Tape rubber or wood blocks to the tops of both doors to prop
them open far enough for air to get in. This stops odor and
mold from building up.
Moving
When you are moving your refrigerator to a new home, follow
these steps to prepare it for the move.
1. If your refrigerator has an automatic ice maker:
Turn off the water supply to the ice maker at least one day
ahead of time.
Disconnect the water line from the back of the refrigerator.
When the last load of ice drops, raise the wire shutoff arm
to the Off (up) position or press the switch to Off,
depending on your model.
2. Remove all food from the refrigerator and pack all frozen food
in dry ice.
3. Empty the ice bin.
4. Turn off the Temperature control(s). See the “Quick Start
Guide.”
5. Unplug refrigerator
6. Clean, wipe, and dry thoroughly.
7. Take out all removable parts, wrap them well, and tape them
together so they don’t shift and rattle during the move.
8. Depending on the model, raise the front of the refrigerator so it
rolls more easily or raise the leveling screws so they don’t
scrape the floor. See “Adjust the Door(s)” or “Door Closing and
Door Alignment.”
9. Tape the doors closed and tape the power cord to the back of
the refrigerator.
When you get to your new home, put everything back and refer to
the “Installation Instructions” section for preparation instructions.
Also, if your refrigerator has an automatic ice maker, remember to
reconnect the water supply to the refrigerator.
INSTALLATION INSTRUCTIONS
Unpack the Refrigerator
WARNING
Excessive Weight Hazard
Use two or more people to move and install or uninstall
appliance.
Failure to do so can result in back or other injury.
Refrigerator Delivery
A minimum door opening of 33" (838 mm) is required. If door
opening is 36" (914 mm) or less, then removal of doors, drawer,
and hinges is required.
Cart the refrigerator from the side for all door openings.
Remove the Packaging
Remove tape and glue residue from surfaces before turning on
the refrigerator. Rub a small amount of liquid dish soap over the
adhesive with your fingers. Wipe with warm water and dry.
Do not use sharp instruments, rubbing alcohol, flammable
fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your refrigerator. For more
information, see “Refrigerator Safety.”
Dispose of/recycle all packaging materials.
When Moving Your Refrigerator:
Your refrigerator is heavy. When moving the refrigerator for
cleaning or service, be sure to cover the floor with cardboard or
hardboard to avoid floor damage. Always pull the refrigerator
straight out when moving it. Do not wiggle or “walk” the
refrigerator when trying to move it, as floor damage could occur.
Clean Before Using
After you remove all of the packaging materials, clean the inside
of your refrigerator before using it. See the cleaning instructions in
“Refrigerator Care.”
Important information to know about glass shelves and
covers:
Do not clean glass shelves or covers with warm water when they
are cold. Shelves and covers may break if exposed to sudden
temperature changes or impact, such as bumping. Tempered
glass is designed to shatter into many small, pebble-size pieces.
This is normal. Glass shelves and covers are heavy. Use both
hands when removing them to avoid dropping
7
Location Requirements
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as gasoline,
away from appliance.
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.
IMPORTANT: This appliance is intended to be used indoor for
household and similar applications such as:
Staff kitchen areas in shops, offices and other working
environments.
Farm houses and by clients in hotels, motels and other
residential type environments.
Bed and breakfast type environments.
Catering and similar non-retail applications.
NOTE: If the manufacturer wants to limit the use of the appliance
to less than the above, this has to be clearly stated in the
instructions.
To ensure proper ventilation for your refrigerator, allow for a 1/2"
(1.25 cm) of space on each side and at the top. Allow for a 1"
(2.54 cm) space behind the refrigerator. If your refrigerator has an
ice maker, allow extra space at the back for the water line
connections. When installing your refrigerator next to a fixed wall,
leave a 3 3/4" (9.5 cm) minimum space between the refrigerator
and wall to allow the door to swing open.
NOTE: This refrigerator is intended for use in a location where the
temperature ranges from a minimum of 55°F (13°C) to a
maximum of 110°F (43°C). The preferred room temperature range
for optimum performance, which reduces electricity usage and
provides superior cooling, is between 60°F (15°C) and 90°F
(32°C). It is recommended that you do not install the refrigerator
near a heat source, such as an oven or radiator.
Electrical Requirements
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Before you move your refrigerator into its final location, it is
important to make sure you have the proper electrical connection.
If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified person.
Do not use a cord that shows cracks or abrasion damage along its
length or at either the plug or connector end.
Recommended Grounding Method
A 115 V, 60 Hz, AC-only 15 A or 20 A fused, grounded electrical
supply is required. It is recommended that a separate circuit
serving only your refrigerator and approved accessories be
provided. Use an outlet that cannot be turned off by a switch. Do
not use an extension cord.
IMPORTANT: If this product is connected to a GFCI (Ground Fault
Circuit Interrupter) protected outlet, nuisance tripping of the power
supply may occur, resulting in loss of cooling. Food quality and
flavor may be affected. If nuisance tripping has occurred, and if
the condition of the food appears poor, dispose of the food.
NOTE: Before performing any type of installation or cleaning, or
removing a light bulb, turn cooling off or turn the control
(Thermostat, Refrigerator or Freezer Control depending on the
model) to Off. On models with a digital temperature control, press
the minus sign touch pads repeatedly until a dash (-) appears in
both the freezer and refrigerator displays. Disconnect the
refrigerator from the electrical source. When you are finished,
reconnect the refrigerator to the electrical source and turn cooling
on or reset the control (Thermostat, Refrigerator or Freezer
Control depending on the model) to the desired setting. See the
“Quick Start Guide”.
Water Supply Requirements
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools Needed:
Flat-blade screwdriver
7/16" and 1/2" Open-end or two
adjustable wrenches
1/4" Nut driver
1/4" Drill bit
Cordless drill
Connect to potable water supply only
Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after
the system. Systems certified for cyst reduction may be used
on disinfected waters that may contain filterable cysts.
All installations must meet local plumbing code requirements.
8
Do not use a piercing-type or 3/16" (4.76 mm) saddle valve
which reduces water flow and clogs more easily.
Use copper or PEX tubing and check for leaks. Install copper
or PEX tubing only in areas where the household temperatures
will remain above freezing.
For models with water filters, the disposable water filter should
be replaced at least every 6 months.
Water Pressure
A cold water supply with water pressure of between 35 and 120
psi (241 and 827 kPa) is required to operate the water dispenser
and ice maker. If you have questions about your water pressure,
call a licensed, qualified plumber.
NOTE: If the water pressure is less than what is required, the flow
of water from the water dispenser could decrease or ice cubes
could be hollow or irregular shaped.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a
reverse osmosis system going to the water inlet valve of the
refrigerator needs to be between 35 and 120 psi (241 and
827 kPa).
If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).
If the water pressure to the reverse osmosis system is less than
40 to 60 psi (276 to 414 kPa):
Check to see whether the sediment filter in the reverse
osmosis system is blocked. Replace the filter if necessary.
Allow the storage tank on the reverse osmosis system to refill
after heavy usage. The tank capacity could be too small to
keep up with the requirements of the refrigerator.
NOTE: Faucet-mounted reverse osmosis systems are not
recommended.
If your refrigerator has a water filter, it may further reduce the
water pressure when used in conjunction with a reverse
osmosis system. Remove the water filter. See “Water Filtration
System”.
If you have questions about your water pressure, call a licensed,
qualified plumber.
Connect the Water Supply
Read all directions before you begin
IMPORTANT:
Plumbing shall be installed in accordance with the
International Plumbing Code and any local codes and
ordinances.
The water tubing on the back of the refrigerator (which is used
to connect to the household water line) is a PEX (cross-linked
polyethylene) tube. Copper and PEX tubing connections from
the household water line to the refrigerator are acceptable, and
will help avoid off-taste or odor in your ice or water. Check for
leaks. If PEX tubing is used instead of copper, we recommend
contacting Service to obtain current part numbers.
Install tubing only in areas where temperatures will remain
above freezing.
Connect to a potable water supply only.
Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after
the system. Systems certified for cyst reduction may be used
on disinfected waters that may contain filterable cysts.
Tools Needed:
Gather the required tools and parts before starting installation.
Flat-blade screwdriver
7/16" and 1/2" Open-end or two
adjustable wrenches
1/4" Nut driver
1/4" Drill bit
Cordless drill
NOTE: Your refrigerator dealer has a kit available with a 1/4" (6.35
mm) saddle-type shutoff valve, a union, and copper or PEX
tubing. Before purchasing, make sure a saddle-type valve
complies with your local plumbing codes. Do not use a piercing-
type or 3/16" (4.76 mm) saddle valve which reduces water flow
and clogs more easily.
Connect to Water Line
IMPORTANT: If you turn on the refrigerator before the water line is
connected, turn off the ice maker.
1. Unplug refrigerator or disconnect power.
2. Turn off main water supply. Turn on nearest faucet long
enough to clear line of water.
3. Use a quarter-turn shutoff valve or the equivalent, served by a
1/2" copper or PEX household supply line.
NOTE: To allow sufficient water flow to the refrigerator, a
minimum 1/2" size copper or PEX household supply line is
recommended.
A. Bulb
B. Nut
C. Copper or PEX tubing (to refrigerator)
D. Household supply line (½" minimum)
4. Now you are ready to connect the copper or PEX tubing to the
shutoff valve. Use 1/4" (6.35 mm) O.D. (outside diameter) soft
copper or PEX tubing to connect the shutoff valve and the
refrigerator.
Ensure that you have the proper length needed for the job.
Be sure both ends of the copper tubing are cut square.
Slip compression sleeve and compression nut onto copper
tubing as shown. (PEX tubing has compression sleeves
and compression nuts preinstalled.) Insert end of tubing
into outlet end squarely as far as it will go. Screw
compression nut onto outlet end with adjustable wrench.
Do not overtighten.
A. Compression sleeve
B. Compression nut
C. Copper or PEX tubing
9
5. Place the free end of the tubing into a container or sink, and
turn on main water supply to flush out tubing until water is
clear. Turn off shutoff valve on the water pipe.
NOTE: Always drain the water line before making the final
connection to the inlet of the water valve, to avoid possible
water valve malfunction.
6. Bend the copper or PEX tubing to meet the water line inlet,
which is located on the back of the refrigerator cabinet. Leave
a coil of copper or PEX tubing to allow the refrigerator to be
pulled out of the cabinet or away from the wall for service.
Connect to Refrigerator
Depending on your model, the water line may come down from
the top or up from the bottom. Follow the connection instructions
for your model.
Style 1
1. Remove plastic cap from water valve inlet port. Attach the
copper or PEX tube to the valve inlet using a compression nut
and sleeve as shown. Tighten the compression nut. Do not
overtighten. Confirm copper or PEX tubing is secure by pulling
on tubing.
2. Create a service loop with the copper tubing. Avoid kinks
when coiling the tubing. Secure copper or PEX tubing to
refrigerator cabinet with a “P” clamp.
A. Copper or PEX
tubing
B. “P” clamp
C.
Compression nut
D. Compression sleeve
3. Turn on water supply to refrigerator and check for leaks.
Correct any leaks.
Style 2
1. Unplug refrigerator or disconnect power.
2. Remove and discard the short, black plastic part from the end
of the water line inlet.
3. Thread the nut onto the end of the tubing. Tighten the nut by
hand. Then tighten it with a wrench two more turns. Do not
overtighten.
NOTE: To avoid rattling, be sure the copper tubing does not
touch the cabinet’s side wall or other parts inside the cabinet.
A. Household water line
B. Nut (purchased)
C. Ferrule (purchased)
D. Refrigerator water tubing
4. Install the water supply tube clamp around the water supply
line to reduce strain on the coupling.
5. Turn shutoff valve on.
6. Check for leaks. Tighten any connections (including
connections at the valve) or nuts that leak.
7. On some models, the ice maker is equipped with a built-in
water strainer. If your water conditions require a second water
strainer, install in the 1/4ʺ (6.35 mm) water line at either tube
connection. Obtain a water strainer from your appliance
dealer.
Style 3
1. Unplug refrigerator or disconnect power.
2. Turn OFF main water supply. Turn ON nearest faucet long
enough to clear line of water.
3. Find a 1/2" to 1
1
4
" (12.7 mm to 31.8 mm) vertical cold water
pipe near the refrigerator.
NOTE:
Make sure it is a cold water pipe.
Horizontal pipe will work, but the following procedure must
be followed: Drill on the top side of the pipe, not the
bottom. This will help keep water away from the drill. This
also keeps normal sediment from collecting in the valve.
4. Determine the length of copper tubing you need. Measure
from the connection on the rear of the refrigerator to the water
pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4" (6.35 mm)
O.D. (outside diameter) copper tubing. Be sure both ends of
copper tubing are cut square.
5. Using a cordless drill, drill a 1/4" hole in the cold water pipe
you have selected.
A. Cold water pipe
B. Pipe clamp
C. Copper tubing
D. Compression nut
E. Compression sleeve
F. Shutoff valve
G. Packing nut
6. Fasten the shutoff valve to the cold water pipe with the pipe
clamp. Be sure the outlet end is solidly in the 1/4" drilled hole
in the water pipe and that the washer is under the pipe clamp.
Tighten the packing nut. Tighten the pipe clamp screws slowly
and evenly so the washer makes a watertight seal. Do not
overtighten.
7. Slip the compression sleeve and compression nut on the
copper tubing as shown. Insert the end of the tubing into the
outlet end squarely as far as it will go. Screw compression nut
onto outlet end with adjustable wrench. Do not overtighten or
you may crush the copper tubing.
8. Place the free end of the tubing in a container or sink, and turn
ON the main water supply. Flush the tubing until water is clear.
Turn OFF the shutoff valve on the water pipe.
Connect to Refrigerator
1. Create a service loop (minimum diameter of 2 ft [61 cm]) with
the copper tubing. Avoid kinks when coiling the copper tubing.
2. Remove the plastic cap from water valve inlet port. Place a
compression nut and sleeve on the copper tubing.
10
3. Insert the end of the copper tubing into the water valve inlet
port. Shape tubing slightly so that the tubing feeds straight into
the port to avoid kinks.
4. Slide the compression nut over the sleeve and screw into the
water valve inlet port.
A. Plastic water tubing
B. Sleeve
C. Compression nut
D. Copper tubing
5. Using an adjustable wrench, hold the nut on the plastic water
line to keep it from moving. Then, with a second wrench turn
the compression nut on the copper tubing counterclockwise to
completely tighten. Do not overtighten.
A. “P” clamp
B. Plastic water line
C. Water valve inlet
port
D. Compression nut
E. Copper tubing
6. Check connection by pulling on copper tubing. Attach the
plastic water line to the refrigerator cabinet with a “P” clamp.
7. Turn on water supply to the refrigerator and check for leaks.
Correct any leaks.
Complete the Installation
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
1. Plug into a grounded 3–prong outlet.
NOTE: Allow 24 hours to produce the first batch of ice.
Discard the first three batches of ice produced. Allow 3 days to
completely fill the ice storage bin.
2. Flush the water system. See “Water and Ice Dispensers.”
Install Air Filter (on some models)
The air filter reduces the buildup of odors. This helps to maintain a
cleaner environment inside your refrigerator. An air filter is 15
times more powerful than baking soda at reducing common food
odors inside the refrigerator.
Your refrigerator's accessory packet includes an air filter, which
must be installed prior to use. On some models, the air filter is
already installed at the factory.
Installing the Air Filter
Depending on your model, the air filter can be installed in one of
the following ways:
Style 1–Behind Vented Door:
Install the air filter behind the vented door, located on the rear wall
near the top of the refrigerator compartment.
1. Remove the air filter from its packaging.
NOTE: An air filter status indicator is included with the air filter.
The indicator is not needed for models that display the air filter
status on the control panel.
2. Lift open the vented door.
3. Snap the filter into place.
11
A. Air filter
Style 2–Behind LED Vent Cover
Install the air filter behind the blue LED-lighted vent cover, located
on the rear wall near the middle of the refrigerator.
1. Remove the air filter from its packaging.
2. Firmly grasp plastic cover on the vented cover with both hands
and pull out to remove.
NOTE: When cover is removed for the first time, a small foam
part the size of the filter will need to be discarded.
3. Snap the filter into place.
A. Air filter
Installing the Filter Status Indicator (on some
models)
The air filter icon on the control panel displays the air filter status.
Blue: Good.
Yellow: Order a replacement.
Red: Replace air filter.
Red and flashing “Replace Filter”: Expired.
After replacing the air filter, press and hold the Air Filter button for
3 seconds. The filter icons will turn off. See “Quick Start Guide.”
When the system is reset, the air filter icon will return to its blue
color and the words “Replace Filter” will disappear from the
control panel.
NOTE: At any filter status, pressing and holding the Air Filter
button for 3 seconds will reset the air filter status to Good and the
air filter icon will turn off.
Replacing the Air Filter
The disposable air filter should be replaced every 6 months, or
when the status indicator air filter icon turns on and starts flashing
when the refrigerator door is opened.
To order a replacement air filter, see ordering information in the
Quick Start Guide.
1. Remove the used air filter by squeezing in on the side tabs.
2. Install the new air filter and status indicator using the
instructions in the previous sections.
Air Filter Status Indicator—Standard Installation
The filter comes with a status indicator, which should be activated
and installed at the same time the air filter is installed.
1. Place the indicator facedown on a firm, flat surface.
2. Apply pressure to the bubble on the back of the indicator, until
the bubble pops to activate the indicator.
3. Lift open the vented air filter door. On some models, there are
notches behind the door.
On models with notches:
With the indicator screen facing outward, slide the indicator
down into the notches.
NOTE: The indicator will not easily slide into the notches if the
rear bubble has not been popped.
Close the air filter door, and check that the indicator is visible
through the window in the door.
A. Status indicator window
B. Air filter status indicator
C. Notches
Place the indicator in a visible place you will easily remember
—either inside the refrigerator or elsewhere in your kitchen or
home.
Replacing the Air Filter
The disposable air filter should be replaced every 6 months, when
the status indicator has completely changed from white to red.
To order a replacement air filter, see ordering information in the
Quick Start Guide.
1. Remove the used air filter by squeezing in on the side tabs.
2. Remove the used status indicator.
3. Install the new air filter and status indicator using the
instructions in the previous sections.
12
Install Produce Preserver (on some
models)
Your refrigerator's accessory packet includes a Produce
Preserver, which should be installed prior to use. On some
models, the Produce Preserver is already installed at the factory.
To order a replacement produce preserver, use part number
W10346771.
The Produce Preserver absorbs ethylene, allowing the ripening
process of many produce items to slow down. As a result, certain
produce items will stay fresh longer.
Ethylene production and sensitivity varies depending on the type
of fruit or vegetable. To preserve freshness, it is best to separate
produce with sensitivity to ethylene from fruits that produce
moderate to high amounts of ethylene.
Sensitivity to
Ethylene
Ethylene
Production
Apples High Very High
Asparagus Medium Very Low
Berries Low Low
Broccoli High Very Low
Cantaloupe Medium High
Carrots Low Very Low
Citrus Fruit Medium Very Low
Grapes Low Very Low
Lettuce High Very Low
Pears High Very High
Spinach High Very Low
Installing the Produce Preserver
CAUTION: IRRITANT. MAY IRRITATE EYES AND SKIN.
DANGEROUS FUMES FORM WHEN MIXED WITH OTHER
PRODUCTS.
Do not mix with cleaning products containing ammonia, bleach,
or acids. Do not get in eyes, on skin or clothing. Do not breathe
dust. Keep out of reach of children.
FIRST AID TREATMENT: Contains potassium permanganate. If
swallowed, call a Poison Control Center or doctor immediately.
Do not induce vomiting. If in eyes, rinse with water for 15
minutes. If on skin, rinse with water.
Style 1–Located Inside the Refrigerator:
1. Find the Produce Preserver housing inside the refrigerator.
2. Lift up on the housing to remove it from the mounting tab.
3. Open the housing by pulling up and out on the back of the top
of the housing.
4. Remove the Produce Preserver pouches from the packaging.
Place them into the housing then snap housing back together.
NOTE: For best performance, always use two pouches.
5. Adhere the Produce Preserver housing to the back wall of the
crisper drawer according to the instructions included in the
package.
6. Place housing back on mounting tab.
Style 2–Located in Crisper or Refrigerator Drawers:
For your convenience, the suction-mounted produce preserver
can be installed in either the crisper or the refrigerated drawers.
1. Wash the interior of a drawer with a solution of mild dish soap
and warm water and dry thoroughly.
2. Find the package containing the Produce Preserver inside the
refrigerator and install the Produce Preserver into the drawer,
according to the instructions provided in the package.
Installing the Status Indicator
The Produce Preserver comes with a status indicator, which
should be activated and installed at the same time the pouch is
installed.
1. Place the indicator facedown on a firm, flat surface.
2. Apply pressure to the bubble on the back of the indicator, until
the bubble pops to activate the indicator.
3. Slide open the cap on the Produce Preserver housing.
4. Place the indicator in the top of the housing, facing outward.
5. Slide the cap closed, and check that the indicator is visible
through the rectangular hole in the cap.
NOTE: The cap will not close easily if the indicator’s rear
bubble has not been popped.
Replacing the Produce Preserver Pouches
The disposable pouches should be replaced every 6 months,
when the status indicator has completely changed from white to
red.
To order replacements, see the contact information in the Quick
Start Guide. Order part number W10346771A or FRESH1.
1. Remove the used pouches from the produce preserver
housing.
2. Remove the used status indicator.
3. Install the new pouches and status indicator using the
instructions in the previous sections or instructions included in
the replacement packets.
REFRIGERATOR FEATURES
Crisper Humidity Control (on some
models)
You can control the amount of humidity in the moisture-sealed
crisper. Depending on your model, adjust the control to any setting
between Fruit and Vegetables or Low and High.
13
Fruit/Low (open):
Move control to allow moist air out of the crisper for best storage
of fruits and vegetables with skins.
Fruit: Wash, let dry and store in refrigerator in plastic bag or
crisper. Do not wash or hull berries until they are ready to use.
Sort and keep berries in original container in crisper, or store in
a loosely closed paper bag on a refrigerator shelf.
Vegetables with skins: Place in plastic bags or plastic
container and store in crisper.
Vegetables/High (closed):
Move control to keep moist air in the crisper for best storage of
fresh, leafy vegetables.
Leafy vegetables: Wash in cold water, drain and trim or tear off
bruised and discolored areas. Place in plastic bag or plastic
container and store in crisper.
Water and Ice Dispensers (on some
models)
For additional information on how to use your water and ice
dispensers, see the online “Dispensing Guide.”
IMPORTANT:
After connecting the refrigerator to a water source or replacing
the water filter, flush the water system. Use a sturdy container
to depress and hold the water dispenser pad for 5 seconds,
then release it for 5 seconds. Repeat until water begins to flow.
Once water begins to flow, continue depressing and releasing
the dispenser pad (5 seconds on, 5 seconds off) until a total of
4 gal. (15 L) has been dispensed. This will flush air from the
filter and water dispensing system, and prepare the water filter
for use. Additional flushing may be required in some
households. As air is cleared from the system, water may spurt
out of the dispenser.
Allow 24 hours for the refrigerator to cool down and chill water.
Dispense enough water every week to maintain a fresh supply.
Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced.
The dispenser will dispense either water or ice.
The dispensing system will not operate when the refrigerator
door is open.
On some models, the display screen on the dispenser control
panel will turn off automatically and enter “sleep” mode when
the control buttons and dispenser levers have not been used
for 2 minutes or more. While in “sleep” mode, the first press of
a control button will only reactivate the display screen without
changing any settings. After reactivation, changes to any
settings can then be made. If no changes are made within 2
minutes, the display will re-enter “sleep” mode.
Flush the Water System
Air in the water dispensing system can cause the water dispenser
to drip. After connecting the refrigerator to a water source or
replacing the water filter, flush the water system.
Flushing the water dispensing system forces air from the water
line and filter and prepares the water filter for use. Additional
flushing may be required in some households.
NOTE: As air is cleared from the system, water may spurt out of
the dispenser.
1. Using a sturdy container, depress and hold the water
dispenser paddle for 5 seconds.
2. Release the dispenser paddle for 5 seconds. Repeat steps 1
and 2 until water begins to flow.
3. Once water begins to flow, continue depressing and releasing
the dispenser pad (5 seconds on, 5 seconds off) until a total of
3 gal. (12 L) has been dispensed.
The Water Dispenser
IMPORTANT:
Dispense at least 1 qt. (1 L) of water every week to maintain a
fresh supply.
If the flow of water from the dispenser decreases, it could be
caused by low water pressure.
With the water filter removed, dispense 1 cup (237 mL) of
water. If 1 cup of water is dispensed in 8 seconds or less, the
water pressure to the refrigerator meets the minimum
requirement.
If it takes longer than 8 seconds to dispense 1 cup (237 mL) of
water, the water pressure to the refrigerator is lower than
recommended. See “Water Supply Requirements” and online
“Troubleshooting” for more information.
Cleaning the Ice Dispenser Chute
Humidity causes ice to naturally clump together. Ice particles can
build up until the ice dispenser chute becomes blocked.
If ice is not dispensed regularly, it may be necessary to empty the
ice storage bin and clean the ice delivery chute, the ice storage
bin and the area beneath the storage bin every 2 weeks.
If necessary, remove the ice clogging the storage bin and
delivery chute, using a plastic utensil.
Clean the ice delivery chute and the bottom of the ice storage
bin using a warm, damp cloth and dry thoroughly.
Ice Maker and Storage Bin
IMPORTANT:
To avoid low ice production and poor quality ice, flush the water
system before turning on the ice maker. See “Water and Ice
Dispenser” for details.
Following installation, allow 24 hours to produce the first batch
of ice. Allow 2 to 3 days to fill the ice storage bin.
For models with a water filter, after connecting the refrigerator
to a water source or replacing the water filter, fill and discard
three full containers of ice to prepare the water filter for use.
The quality of your ice will be only as good as the quality of the
water supplied to your ice maker. Avoid connecting the ice
maker to a softened water supply. Water softener chemicals
(such as salt) can damage parts of the ice maker and lead to
poor quality ice. If a softened water supply cannot be avoided,
make sure the water softener is operating properly and is well
maintained.
If the ice in the storage bin clumps together, break up ice using
a plastic utensil and discard ice. Do not use anything sharp to
break up the ice. This can cause damage to the ice bin and the
dispenser mechanism.
Do not store anything on top of the ice maker or in the ice
storage bin.
Ice Production Rate
Allow 24 hours to produce the first batch of ice. Discard the first
three batches of ice produced.
Allow 3 days to completely fill the ice storage bin. The ice maker
should produce approximately 3 lbs (1.4 kg) (8 to 12 batches) of
ice in a 24-hour period.
To increase ice production, lower the freezer and refrigerator
temperature, or see “Control Panel Descriptions” in the Quick
Start Guide for details. Wait 24 hours between adjustments.
14
Ice Maker in the Freezer
Turn the Ice Maker On/Off:
To turn on the ice maker, simply lower the wire shutoff arm.
To manually turn the ice maker off, lift the wire shutoff arm to the
off (arm up) position and listen for the click.
Your ice maker has an automatic shutoff. As ice is made, the ice
cubes will fill the ice storage bin and the ice cubes will raise the
wire shutoff arm to the off (arm up) position. Do not force the wire
shutoff arm up or down.
NOTE: Turn off the ice maker before removing the ice storage bin
to serve ice or to clean the bin. This will keep the ice cubes from
dropping out of the ice maker and into the freezer compartment.
After replacing the ice storage bin, turn on the ice maker.
Wash the ice storage bin with mild soap and warm water.
Slide the ice storage bin under the ice maker and push it toward
the back as far as it will go.
Auto Ice Storage Bin (on some models):
Your ice storage bin has a lever which allows the storage bin to
slide out with the drawer when it is pulled open or to stay in place.
Move the lever to the right to attach the ice storage bin to the
freezer drawer.
Move the lever to the left to release the ice storage bin from
the freezer drawer.
A. Ice storage bin lever
Ice Maker in the Refrigerator (on some models)
Style 1—Left-Hand Refrigerator Door
The ice maker is located on the left-hand side of the refrigerator
door. Ice cubes are ejected into the ice storage bin, located on the
left-hand refrigerator door.
Turn the Ice Maker On/Off:
1. Push up on the latch on the left-hand side of the ice
compartment to open the door.
A. Ice compartment door latch
2. Turn on the ice maker by moving the switch to the (left) on
position.
To manually turn off the ice maker, move the control to the
off (right) position.
Your ice maker has an automatic shutoff. The sensor will
automatically stop ice production if the storage bin is full, if
the door is open or the storage bin is removed. The control
will remain in the on (left) position.
A. Ice storage bin release latch
3. Close the ice compartment door.
Remove and Replace the Ice Storage Bin:
Remove the ice storage bin by inserting your fingers into the
hole at the base of the bin and squeezing the latch to release
the bin from the compartment. Lift the storage bin up and pull it
straight out.
Replace the storage bin inside the ice compartment and push
down to make sure it is firmly in place.
Style 2—Upper Left-Hand Side of the Refrigerator
Compartment
The ice maker and storage bin are located in the upper left-hand
side of the refrigerator compartment.
Turn the Ice Maker On/Off:
The ice maker has an automatic shutoff. When the ice maker is
on, sensors will automatically stop ice production when the
storage bin is full. The ice maker will remain set to on, and ice
production will resume when the bin is no longer full.
NOTE: Some models have an on/off switch located on the ice
maker storage bin. To turn on the ice maker, press the switch to
the On position. To manually turn off the ice maker, press the
switch to the Off position.
To manually turn off the ice maker, see the Quick Start Guide for
more information.
Remove and Replace the Ice Storage Bin:
1. Hold the base of the storage bin and press the release button
on the lower right.
2. Pull out the storage bin until resistance is felt. Lift up the front
of the ice bin and remove.
3. Press the switch to Off (on some models).
IMPORTANT: To remove the ice storage bin, it may be necessary
to turn the auger driver, behind the ice bin, counterclockwise to
properly align the ice bin with the auger driver. The ice storage bin
must be locked in place for proper ice dispensing.
A. On position (on some models)
B. Auger driver
15
1. Press the switch to On (on some models).
2. Slide the ice bin into the guide rails located on either side of
the enclosure.
3. Push the ice bin in until resistance is felt. Raise the front
slightly and push the ice bin in until an audible “click” is heard.
Style 3—Left-Hand Door Behind the Refrigerator Bins
The ice maker is located on the left door behind the bins. Ice
cubes are ejected into the ice storage bin located on the left-hand
refrigerator door.
Turn the Ice Maker On/Off:
1. Push up on the latch on the left-hand side of the ice
compartment to open the door.
2. Turn on the ice maker by moving the switch to the On (I)
position.
3. Close the ice compartment door.
Remove and Replace the Ice Storage Bin:
Remove the ice storage bin by inserting your fingers into the
hole at the base of the bin and squeezing the latch to release
the bin from the compartment. Lift the storage bin up and pull it
straight out.
Replace the storage bin inside the ice compartment and push
down to make sure it is firmly in place.
Water Filtration System
Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after the
system. Systems certified for cyst reduction may be used on
disinfected waters that may contain filterable cysts.
IMPORTANT: The disposable water filter should be replaced at
least every 6 months. If the water flow to the water dispenser or
ice maker decreases noticeably before 6 months have passed,
replace the water filter more often.
Install the Water Filter
To order a replacement filter, contact us at www.whirlpool.com/
Parts & Accessories. See the “Quick Start Guide” for details.
NOTE: If the filter is not installed correctly, water may dispense at
a lower flow rate and there will be slower ice production. Improper
filter installation may also cause the water filter housing to leak.
Style 1 Bottom Left of Refrigerator Compartment
1. Push the water filter door to open, located bottom left of
refrigerator compartment.
2. Twist the water filter and turn 90° counterclockwise to unlock.
3. Pull the filter out of the housing.
4. Remove the water filter cap from the water filter.
5. Install the water filter cap onto the new filter. Be sure to align
the arrows so the grooves in the filter align with ribs in the filter
cap.
16
6. Insert the filter into the housing.
7. Twist the water filter and turn 90° clockwise until it locks into
place and the arrows are aligned.
8. Push the water filter door closed.
Style 2— Right-Hand Side of Refrigerator Ceiling
1. Locate the accessory packet in the refrigerator and remove
the water filter.
2. Take the water filter out of its packaging and remove the cover
from the O-rings. Be sure the O-rings are still in place after the
cover is removed.
A. O-ring cover
B. O-rings
3. The water filter compartment is located in the right-hand side
of the refrigerator ceiling. Push up on the compartment door to
release the catch, then lower the door.
4. Align the arrow on the water filter label with the cutout notch in
the filter housing and insert the filter into the housing.
5. Turn the filter clockwise 90 degrees (1/4 turn), until it locks into
the housing.
NOTE: If the filter is not correctly locked into the housing, the
water dispenser will not operate. Water will not flow from the
dispenser.
6. While the compartment door is still open, lift the filter up into
the compartment. Then, close the filter compartment door
completely.
7. Flush the water system. See “Water and Ice Dispensers” for
details.
IMPORTANT: If you do not flush the water system, you may
experience dripping and/or decreased flow from the water
dispenser.
Style 3— Top-right Corner of Refrigerator Ceiling
1. Locate the water filter in the top-right corner of the refrigerator
compartment.
2. Lift open the filter cover door. The filter will be released and
then eject as the door is opened.
3. When the door is completely open, pull the filter straight out.
NOTE: There may be some water in the filter. Some spilling
may occur. Use a towel to wipe up any spills.
4. Take the new filter out of its packaging and remove the covers
from the O-rings. Be sure the O-rings are still in place after the
covers are removed.
5. With the arrow pointing up, align the new filter with the filter
housing and slide it into place. The filter cover door will
automatically begin to close as the new filter is inserted.
6. Close the filter cover door completely in order to snap the filter
into place. You may need to press hard.
7. Flush the water system. See “Water and Ice Dispensers” for
details.
17
Replacing the Water Filter
To purchase a replacement water filter, use model number
EDR4RXD1, UKF8001AXX-200 or UKF8001AXX-750, contact
your dealer, or call 1-800-422-9991 in the U.S.A. or 1-800-807-
6777 in Canada.
IMPORTANT: Air trapped in the water system may cause water
and filter to eject. Always dispense water for at least 2 minutes
before removing the filter or blue bypass cap.
1. If applicable, press upward on the water filter cover to access
the filter.
2. Turn filter counterclockwise, and pull straight out to remove.
NOTE: There may be some water in the filter. Some spilling
may occur. Use a towel to wipe up any spills.
3. Remove sealing label from replacement filter and insert the
filter end into the filter head.
4. Turn the filter clockwise until it stops. Snap the filter cover
closed.
5. Flush the water system. See “Water and Ice Dispensers” for
details.
NOTE: The dispenser feature may be used without a water filter
installed. Your water will not be filtered. If this option is chosen,
replace the filter with the blue bypass cap.
Reset Water Filter Status
After replacing the water filter, press and hold Reset Filter or Filter
Reset (depending on your model) for 3 seconds. The Order and
Replace indicator lights will blink and then go off when the system
is reset. On some models the indicator light will change to blue
when the system is reset. See the “Quick Start Guide” for more
information.
On models with Options and Measured Fill buttons located
on the control panel:
After changing the water filter, reset the status light. Press the
Options button to enter Options mode, then press Lock to initiate
the reset, then press Measured Fill to confirm that you want to
reset the status light. When the system is reset, the “Order” and
“Replace” icons will disappear from the display screen.
On models with Water Filter button located on the control
panel:
After changing the water filter, reset the status. Press and hold the
Water Filter button for 3 seconds. When the system is reset, the
water filter icon will return to Blue and the words “Replace Filter”
will disappear from the display.
DOOR AND HANDLE
INSTRUCTIONS
Door and Drawers
Depending on the width of your doorway, you may need to remove
the doors to move the refrigerator into your home. Also, the door
hinges are factory installed on the right-hand side. If you want the
door to open from the other direction, you must reverse the door
swing.
IMPORTANT:
If the refrigerator was previously installed and you are moving
it out of the home, before you begin, turn the refrigerator
control Off, and unplug the refrigerator or disconnect power.
Remove food and any adjustable door or utility bins from
doors.
Keep the refrigerator doors closed until you are ready to lift
them free from the cabinet. Provide additional support for the
refrigerator door while the hinges are being removed. Do not
depend on the door gasket magnets to hold the door in place
while you are working.
Tools Needed: 5/16", 3/8", and 1/4" hex head socket wrenches,
Torx®† T25 screwdriver, #2 Phillips screwdriver, and a flat-blade
screwdriver.
Remove and Replace Handles
REFRIGERATOR DOOR HANDLES
Refrigerator Door Handle Style 1
A. 3/32” Setscrew
Using a 3⁄32" or 1⁄8" hex key,
loosen the two setscrews located
on the side of each handle. Pull
the handle straight out from the
drawer. Make sure you keep the
screws for reattaching the
handles.
To replace the handles, reverse
the directions.
Refrigerator Door Handle Style 2
A. Handle Trim C. Refrigerator Door Handle
B. Flat–Head Handle Screws
Remove the screw cover.
Remove the handle assembly. Keep all parts together.
To replace the handles, reverse the directions.
18
Refrigerator Door Handle Style 3
A. Flat–Head Handle Screws B. Refrigerator Door Handle
Using a 3⁄32" or 1⁄8" hex key, loosen the two setscrews located
on the side of each handle. Pull the handle straight out from
the drawer. Make sure you keep the screws for reattaching the
handles.
To replace the handles, reverse the directions.
Refrigerator Door Handle Style 4
A. 3/32” or 1/8” Setscrews
To remove the handle, remove the screw attaching the trim to
the upper end of the handle. Using a flat-blade screwdriver
wrapped in masking tape, pry the trim piece from the lower end
of the handle. Then, remove the screws attaching the handle
to the door.
To replace the handles, reverse the directions.
Refrigerator Door Handle Style 5
To remove the handle, grasp the
lower part of the handle firmly,
slide the handle up and pull the
handle straight out from the door.
To replace the handle, position the
handle so that the large holes in
the mounting clips are down and
align the holes with the door studs.
Rotate the handle so that the
mounting clips are flat against the
door and slide the handle down to
engage.
FREEZER DOOR HANDLES
Freezer Door Handle Style 1
A. 3/32” Setscrew
Using a 3⁄32" or 1⁄8" hex key, loosen the two setscrews located
on the side of each handle. Pull the handle straight out from
the drawer. Make sure you keep the screws for reattaching the
handles.
To replace the handles, reverse the directions.
Freezer Door Handle Style 2
A. 3/32” or 1/8” Setscrews
Using a 3⁄32" or 1⁄8" hex key, loosen the two setscrews located
on the side of each handle. Pull the handle straight out from
the drawer. Make sure you keep the screws for reattaching the
handles.
To replace the handles, reverse the directions.
Freezer Door Handle Style 3
A. Flat–Head Handle Screws
Remove screws and handle.
To replace the handles, reverse the directions.
Freezer Door Handle Style 4
A. Flat–Head Screws B. Freezer Drawer Handle
Remove screws and handle.
To replace the handles, reverse the directions.
19
Freezer Door Handle Style 5
To remove the handle, grasp the lower part of the handle
firmly, slide the handle up and pull the handle straight out from
the door.
To replace the handle, position the handle so that the large
holes in the mounting clips are down and align the holes with
the door studs. Rotate the handle so that the mounting clips
are flat against the door and slide the handle down to engage.
Remove Refrigerator Doors and
Hinges
WARNING
Electrical Shock Hazard
Disconnect power before removing doors.
Failure to do so could result in death or electrical shock.
1. Unplug refrigerator or disconnect power.
2. Remove base grille.
BASE GRILLE
Style 1
Using both hands, grasp the grille firmly and pull it toward you.
Open the freezer drawer to access the brake feet.
NOTE: To allow the refrigerator to roll easier, raise the brake
feet by turning them counterclockwise. The front rollers will be
touching the floor.
Style 2
Remove the two screws fastening the base grille to the cabinet
and set screws aside.
Grasp the grille and pull it toward you.
NOTE: To allow the refrigerator to roll easier, raise the brake
feet by turning them counterclockwise. The front rollers will be
touching the floor.
Style 3
Use a 1/4” hex–nut driver to remove both screws in the base
grille.
Using both hands, grasp the grille firmly and pull it toward you.
Open the freezer drawer to access the brake feet.
NOTE: To allow the refrigerator to roll easier, raise the brake
feet by turning them counterclockwise. The front rollers will be
touching the floor.
Remove Right-Hand Refrigerator Door
3. Starting with the right-hand side door, remove the parts for the
top hinge as shown below.
A. Top hinge cover screw D. Top Hinge
B. Top hinge cover E. Locator Screws
C. 3/16" Internal hex-head screws
NOTE: Do not remove the two locator screws. These screws
will help you align the hinge when you replace the door.
20
WARNING
Excessive Weight Hazard
Use two or more people to lift the appliance door.
Failure to do so can result in back or other injury.
4. Lift the refrigerator door from the bottom hinge pin. The top
hinge will come away with the door.
Remove Left-Hand Refrigerator Door
IMPORTANT: On models with a water dispenser, the tubing and
wiring for the water dispenser run through the left-hand door
hinge, so they must be disconnected before removing the door.
1. Remove the cover from the top hinge as shown below.
A. Top hinge cover screw B. Top hinge cover
2. Disconnect the water dispenser tubing located on top of the
door hinge (if applicable).
Water Tubing Connection Style 1: Press the colored outer ring
against the face of the fitting and gently pull the dispenser tubing
free as shown below.
NOTE: The water dispenser tubing remains attached to the left-
hand refrigerator door.
A. Outer ring B. Face of fitting
3. Before removing the left-hand side door, disconnect the wiring
plug located on top of the top hinge by wedging a flat-blade
screwdriver or your fingernail between the two sections.
NOTE: Do not remove the green, ground wire. It should
remain attached to the door hinge.
A. 3/4” Internal hex-head or
TORX T25 screws
C. Locator screws (do not
remove)
B. Ground wire (Do not remove)
4. Lift the refrigerator door from the bottom hinge pin. The top
hinge will come away with the door.
NOTE: It may not be necessary to remove the bottom hinges
and brake feet assemblies to move the refrigerator through a
doorway.
Only if necessary, depending on your model, use a driver
with a #2 square bit tip or a TORX T25 screwdriver to
remove the bottom hinges and a 3/8" nut driver or a TORX
T25 screwdriver to remove the brake feet screws.
Reset Bottom Refrigerator Door
Hinge
For your convenience, the refrigerator doors have bottom hinges
with door closers. These closers allow the doors to swing fully
closed with just a gentle push.
IMPORTANT: So that the closers feature will operate properly, the
doors must be removed only when open to a 90° angle to the front
of the cabinet. If one or both doors were not at a 90° angle when
removed, the bottom door hinge must be reset.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59

Maytag MFI2570FEZ Le manuel du propriétaire

Catégorie
Frigos
Taper
Le manuel du propriétaire
Ce manuel convient également à

dans d''autres langues