Whirlpool WRF953CIHB Manuel utilisateur

W11115282C

FRENCH DOOR BOTTOM-MOUNT REFRIGERATOR

Use and Care Guide

For questions about features, operation/performance,

parts or service, call: 1-800-253-1301

In Canada, call for assistance 1-800-807-6777

or visit our website at

www.whirlpool.com or www.whirlpool.ca

RÉFRIGÉRATEUR À DOUBLE PORTE

Guide de l’utilisateur

Pour des questions à propos des caractéristiques, du fonctionnement/rendement,

des pièces ou du service, composer le : 1-800-253-1301

Au Canada, pour assistance composez le 1-800-807-6777

ou visitez notre site Web au

www.whirlpool.ca

Table of Contents/Table des matières....2

2

REFRIGERATOR SAFETY ............................................................3

PARTS AND FEATURES ...............................................................4

What’s New Behind the Doors? ................................................... 5

GETTING STARTED ......................................................................6

Installation Checklist ....................................................................6

Water Filter Installation ................................................................. 6

Door Alignment ............................................................................7

Energy Saver Mode and Normal Operating Sounds ...................7

INSTALLATION INSTRUCTIONS .................................................8

Unpack the Refrigerator ............................................................... 8

Location Requirements ................................................................8

Remove and Replace Refrigerator Doors .................................... 9

Remove and Replace Freezer Drawer Fronts ............................13

Electrical Requirements .............................................................13

Water Supply Requirements ......................................................14

Connect the Water Supply .........................................................14

Handle Installation and Removal ...............................................15

Refrigerator Leveling and Door Closing .....................................16

FILTERS AND ACCESSORIES ..................................................17

Water Filtration System ..............................................................17

Install Produce Preserver (on some models) .............................18

Accessories ................................................................................19

REFRIGERATOR USE .................................................................19

Opening and Closing Doors .......................................................19

Using the Controls .....................................................................19

External Dispenser Controls ......................................................21

Lighting the Refrigerator ............................................................21

Water and Ice Dispensers ..........................................................22

Ice Maker and Storage Bin .......................................................25

Shelves, Bins, and Drawers .......................................................26

Freezer Drawers .........................................................................28

Audio Reference .........................................................................28

REFRIGERATOR CARE ..............................................................28

Cleaning .....................................................................................28

Lights ..........................................................................................29

Vacation and Moving Care .........................................................29

TROUBLESHOOTING .................................................................30

PERFORMANCE DATA SHEETS ...............................................37

WARRANTY ..................................................................................38

Table of Contents

Table des matières

SÉCURITÉ DU RÉFRIGÉRATEUR .............................................40

PIÈCES ET CARACTÉRISTIQUES .............................................41

Quoi de neuf en coulisse? .........................................................42

MISE EN PLACE ..........................................................................43

Liste de vérication pour l’installation........................................43

Installation du ltre à eau ...........................................................43

Alignement des portes ...............................................................44

Mode de consommation réduite d’énergie et bruits

de fonctionnement normaux ......................................................44

INSTRUCTIONS D’INSTALLATION ...........................................45

Déballage du réfrigérateur..........................................................45

Exigences d’emplacement .........................................................45

Retrait et réinstallation des portes du réfrigérateur ...................46

Retrait et remplacement de l’avant

du tiroir de congélation ..............................................................50

Spécications électriques ..........................................................50

Spécications de l’alimentation en eau .....................................51

Raccordement à la canalisation d’eau ......................................51

Installation et retrait des poignées .............................................52

Nivellement du réfrigérateur et fermeture de la porte................54

FILTRES ET ACCESSOIRES .....................................................54

Système de ltration d’eau ........................................................54

Installation du conservateur de produits frais (sur certains

modèles) .....................................................................................56

Accessoires ................................................................................56

UTILISATION DU RÉFRIGÉRATEUR ........................................56

Ouverture et fermeture des portes .............................................56

Utilisation des commandes .......................................................57

Commandes de distributeur externe .........................................59

Éclairage du réfrigérateur ...........................................................59

Distributeurs d’eau et de glaçons ..............................................59

Machine à glaçons et bac d’entreposage ................................63

Tablettes, balconnets, et tiroirs ..................................................65

Tiroirs du congélateur ................................................................66

Référence audio .........................................................................67

ENTRETIEN DU RÉFRIGÉRATEUR ...........................................67

Nettoyage ...................................................................................67

Lampes .......................................................................................68

Précautions à prendre pour les vacances

ou le déménagement .................................................................68

DÉPANNAGE ................................................................................69

FEUILLES DE DONNÉS DU PRODUIT ......................................77

GARANTIE ....................................................................................78

3

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

follow

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

REFRIGERATOR SAFETY

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

SAVE THESE INSTRUCTIONS

■ Plug into a grounded (earthed) outlet.

■ Do not remove ground prong.

■ Do not use an adapter.

■ Do not use an extension cord.

■ Disconnect power before servicing.

■ Replace all parts and panels before operating.

■ Remove doors from your old refrigerator.

■ Use nonflammable cleaner.

■ Do not store or use petrol, flammable liquids or gas in the

vicinity of this or other electrical appliances. The fumes can

cause fires or explosions.

■ Do not store explosive substances such as aerosol cans

with a flammable propellant in this refrigerator.

■ Do not use or place electrical devices inside the refrigerator

compartments if they are not of the type expressly

authorized by the manufacture.

■ Use two or more people to move and install refrigerator.

■ Disconnect power before installing ice maker (on ice maker

kit ready models only).

■ A qualified service technician must install the water line and

ice maker.

■ Connect to a potable water supply only.

■ Use a sturdy glass when dispensing ice (on some models).

■ This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

■ Children should be supervised to ensure that they do not

play with the appliance.

■ To avoid the risk of children becoming trapped and

suffocating, do not allow them to play or hide inside the

refrigerator.

■ If the power supply cord is damaged, it must be replaced by

the manufacturer or its service agent or a similarly qualified

person.

4

PARTS AND FEATURES

Proper Disposal of

Your Old Refrigerator

WARNING

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not

problems of the past. Junked or abandoned refrigerators are

still dangerous—even if they will sit for “just a few days.” If

you are getting rid of your old refrigerator, please follow these

instructions to help prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children may not easily

climb inside.

Water filter

Auto humidity

crispers

Temperature-

controlled

pantry drawer

Platter pocket

In-Door-Ice

®

ice storage

Infinity slide shelf

Removable

bin

Temperature

Control UI

Dual gallon

storage

Important information to know about disposal of

refrigerants:

Dispose of refrigerator in accordance with Federal and Local

regulations. Refrigerants must be evacuated by a licensed,

EPA certified refrigerant technician in accordance with

established procedures.

5

Energy and Normal Operating Sounds

Your new French door bottom-mount refrigerator has been

designed with a linear compressor to optimize energy efciency

and better regulate temperatures to match cooling demand. You

may notice that it operates differently than your previously owned

refrigerator. This allows the refrigerator to respond at variable

speeds and optimize cooling needs by avoiding abrupt start/stop

cycles.

In-Door-Ice

®

Ice Dispensing System

The ice maker and ice storage bin are located in the door for easy

access to ltered ice while freeing up valuable shelf space inside

and adding additional door bins for more usable space.

Dual Evaporator

The refrigerator and freezer compartments have separate

evaporators to provide fresh food and frozen food with optimal

storage climates: cool and humid in the fresh food compartment,

cold and dry in the freezer with no mixing of air between the

compartments. This reduces the transfer of food odors and

tastes from refrigerator to freezer, and allows freezer air to remain

dry to control frost and reduce freezer burn.

Air Filter

An air lter is 15 times more powerful than baking soda at

reducing common food odors inside the refrigerator. Replace

your air lter every 6 months for maximum odor reduction.

Water Dispenser with Measured Fill

The Measured Fill feature allows you to dispense a desired

amount of ltered water in handy increments like 8, 16, or 24 oz.

Water Dispenser with Favorite Fill

The Favorite Fill feature allows you to save two custom presets

that can be programmed for favorite items that are frequently

lled like a coffee pot or a water bottle.

Innity Slide Shelf

Your new Innity slide shelf or shelves (on some models) is

designed to maximize accessibility to items of all shapes and

sizes. Small items t perfectly around the shelf perimeter and

remain accessible, while tall items nestle perfectly in the center

when the glass is pushed back. And, with the Innity slide shelf,

you don’t lose an entire half shelf to tall item storage—just push

the glass portion back as far as you need to accommodate your

tall items—innite adjustability.

Platter Pocket

This full-width slide-out shelf tucked between the crispers and

the lowest shelf is perfect for leftover family-sized casserole

dishes, pizza boxes, and large party platters.

Electronic Temperature-Controlled Pantry Drawers

These drawers provide precise, independent temperature control

with four specialized settings for maximum exibility.

LED Lighting

There is bright white LED strip lighting for maximum illumination.

LED lights do not require replacement.

Door Ajar Alarm

A helpful alarm sounds when the refrigerator door or freezer

drawer is left ajar.

Power Outage Indicator

If the power should go out while you are away from home, this

indicator will let you know that the refrigerator has been without

power.

To view videos on door removal/

replacement, door adjustment, water

filter installation, air filter installation,

shelf adjustment or removal, scan the

code to the left with your

mobile device.

What’s New Behind the Doors?

Your Whirlpool

®

French door bottom-mount refrigerator comes equipped with various

innovative storage and energy-efcient features.

6

GETTING STARTED

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Installation Checklist

✔ Electrical Power

❑ Plug refrigerator into a grounded 3 prong outlet.

✔ Doors

❑ If doors need to be removed during installation, see the

“Remove and Replace Doors” in the Installation Instructions.

❑ Check that handles are secure and installed according to the

instructions.

❑ Doors seal completely.

❑ Refrigerator is level. (Remove base grille and adjust leveling

feet so they are snug against the oor.)

❑ Doors are even across the top. (Use door alignment feature

if necessary.)

❑ Base grille is properly attached to the refrigerator.

✔ Ice and Water System (on some models)

❑ Connect refrigerator to a cold water supply with 35-120 psi

(241-827 kPa) water pressure, as specied in the instructions.

❑ Make sure the household water supply is connected and

turned on.

❑ Check that the water supply line behind refrigerator is

not kinked.

❑ Only use recommended water supply tubing, copper, or PEX,

as specied in the instructions.

❑ Install water lter according to the instructions.

❑ Flush water system with 3 gallons (11.4 L) of water, as

specied in the instructions.

❑ Check for water leaks at all connections.

❑ Turn on ice maker if refrigerator is connected to water supply.

(If not connected to water supply, turn off ice maker.)

✔ Final Checks

❑ Install air lter according to instructions in corresponding

packaging.

❑ Remove all shipping material.

❑ Set temperature controls to the recommended setting.

❑ Save instructions and other literature.

❑ Send in Registration Card or register your product online.

Water Filter Installation

■ Locate the water lter compartment in the lower left-hand

side of the refrigerator compartment. Push on the right side

of the lter door to open.

■ Align the arrow on the water lter cap with the cutout notch

in the lter housing and insert lter.

■ Once the lter is inserted, turn the lter clockwise 90°

(1/4 turn) until it locks into the housing.

■ Push water lter door closed to latch.

■ Flush 3 gallons (11.4 L) of water through the water system to

clear air from the water line and to keep the dispenser from

dripping and/or avoiding decreased dispenser ow.

NOTE: If the lter is not installed correctly, water may

dispense at a lower ow rate and there will be slower ice

production. Improper lter installation may also cause the

water lter housing to leak.

7

Shelf Height Adjustment

Shelf height can be adjusted by changing the adjustable shelf

mounts between their vertical and horizontal positions.

■ Carefully lift the shelf off the shelf mounts and turn the ipper

to the desired orientation.

■ Repeat for remaining shelf mounts.

■ Ensure the shelf is properly seated on the shelf mounts.

Energy Saver Mode and Normal

Operating Sounds

Your new French door bottom-mount refrigerator has been

designed to optimize energy efciency and better regulate

temperatures to match cooling demand.

You may notice that it operates differently from your previously

owned refrigerator.

It is normal for the high-efciency compressor to run for extended

periods of time at varying speeds in order to consume only the

energy necessary for optimum efciency.

In addition, during various stages of the cooling cycle, you may

hear normal operating sounds that are unfamiliar to you.

Energy Saver Mode

A selectable feature that turns off the heaters around the

refrigerator doors and dispenser. When this feature is enabled,

condensation may form on the front of the refrigerator cabinet,

gasket, or on top of the freezer drawer. Savings may vary based

on the relative humidity of the environment.

Door Alignment

Tools Required

Depending on the width of the door opening, the following tools

may be required to remove, replace, and align the refrigerator

doors.

Tools Needed:

❑ 1/4" hex nut driver – base grille, freezer drawer screws,

and brake/leveling feet

Tools Provided:

❑ 1/8" hex key – handle setscrews and door alignment

Door alignment tool instructions

Features:

❑ Creates an even horizontal gap

between the refrigerator doors.

❑ Solves door alignment issues during

installation and improves

door seal.

Align Refrigerator Doors

✔ If doors are uneven:

❑ Ensure the refrigerator is level.

❑ Keeping both refrigerator doors closed, pull out the freezer

drawer. Locate the bottom hinge pin of the right-hand

refrigerator door. The alignment screw is inside the bottom

hinge pin.

❑ Insert the short end of the 1/8" (3.2 mm) hex key (packed with

the Door Handle Installation Instructions) into the bottom hinge

pin until it is fully engaged in the alignment screw.

To raise the refrigerator door, turn the hex key to the right.

To lower the door, turn the hex key to the left.

❑ Continue to turn the alignment screw until the tops of the

doors are aligned.

8

Location Requirements

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IMPORTANT: This appliances is intended to be used in

household and similar applications such as:

■ Staff kitchen areas in shops, ofce and other working

environments,

■ Farm houses and by clients in hotels, motels and other

residential type environments,

■ Bed and breakfast type environments,

■ Catering and similar non-retail applications.

To ensure proper ventilation for your refrigerator, allow for a

minimum 1/2" (12.7 mm) of space on each side and at the top.

Allow for a minimum 1" (2.54 cm) space behind the refrigerator.

If your refrigerator has an ice maker, allow extra space at

the back for the water line connections. When installing your

refrigerator next to a xed wall, leave a 3³⁄

4

" (9.5 cm) minimum

space between the refrigerator and wall to allow the door to

swing open.

NOTE: This refrigerator is intended for use in a location where

the temperature ranges from a minimum of 55°F (13°C) to a

maximum of 110°F (43°C). The preferred room temperature

range for optimum performance, which reduces electricity usage

and provides superior cooling, is between 60°F (15°C) and 90°F

(32°C). It is recommended that you do not install the refrigerator

near a heat source such as an oven or radiator.

3³⁄

4

" (9.5 cm)

1/2" (12.7 mm)

Unpack the Refrigerator

WARNING

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

Refrigerator Delivery

■ A minimum door opening of 33" (83.8 cm) is required. If the

door opening is 36" (91.4 cm) or less, then removal of doors,

drawer, and hinges is required.

■ Cart the refrigerator from the side for all door openings.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the floor with

cardboard or hardboard to avoid floor damage. Always pull

the refrigerator straight out when moving it. Do not wiggle or

“walk” the refrigerator when trying to move it, as floor

damage could occur.

Remove the Packaging

■ Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your ngers. Wipe with warm water

and dry.

■ Do not use sharp instruments, rubbing alcohol, ammable

uids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator.

■ Dispose of/recycle all packaging materials.

Clean Before Using

After you remove all of the packaging materials, clean the inside

of your refrigerator before using it. See the cleaning instructions

in the “Refrigerator Care” section.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

INSTALLATION INSTRUCTIONS

9

Remove and Replace Refrigerator Doors

NOTE: Measure the width of your house door opening to see whether or not you need to remove the refrigerator doors to move the

refrigerator into your home. If refrigerator door removal is necessary, see the following instructions.

IMPORTANT: If the refrigerator was previously installed and you are moving it out of the home, before you begin, turn the refrigerator

control off. Unplug the refrigerator or disconnect power. Remove food and adjustable door or utility bins from doors.

Gather the required tools and read all instructions before removing doors.

TOOLS NEEDED: TORX T25

†

screwdriver and a #2 Phillips screwdriver

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

Water Dispenser

Tubing Connection

Wiring Plug

Top Right Hinge

Top Left Hinge

A

A. Outer ring

C

B

A

A. TORX T25 screws

B. Ground wire (Do not remove.)

C. Do not remove screws.

90°

Door at 90° Angle

to Cabinet

A. TORX T25 screws

B. Hinge cover screw

C. Top hinge cover

D. Top hinge

A

B

C

D

†TORX and T25 are trademarks of Acument Intellectual Properties, LLC.

10

WARNING

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

Bottom Door Hinge

For your convenience, the refrigerator doors have bottom hinges

with door closers. These closers allow the doors to swing fully

closed with just a gentle push.

IMPORTANT: So that the closers feature will operate properly,

the doors must be removed only when open to a 90° angle to the

front of the cabinet. If one or both doors were not at a 90° angle

when removed, the bottom door hinge must be reset.

90°

Reset the Door Hinge

1. Lift the door from the bottom hinge pin, and place it on a

at surface.

2. Using a TORX T25 screwdriver, remove the bottom hinge with

the bushing from the cabinet.

A. Bushing

B. Hinge base

A

B

3. Insert the bottom hinge and bushing into the corresponding

slot in the bottom of the door.

NOTE: Make sure that the base of the hinge is parallel to the

bottom of the door.

A. Hinge base parallel to the bottom edge of the door

A

4. Turn the hinge until the hinge base is at a 90° angle to the

bottom edge of the door.

A. Hinge base turned to a 90° angle with the bottom edge of the door

90°

A

5. Remove the hinge from the door. Using a TORX T25

screwdriver, reattach the bottom hinge to the refrigerator

cabinet.

6. The hinge is now reset and prepared for the door to be

replaced. See “Replace Refrigerator Doors” later in

this section.

11

WARNING

Excessive Weight Hazard

Use two or more people to lift the refrigerator door.

Failure to do so can result in back or other injury.

5. Open the door until it is at a 90° angle to the front of the

cabinet.

6. Lift the refrigerator door from the bottom hinge pin. The top

hinge will come away with the door.

Remove Left-Hand Door

IMPORTANT: The tubing and wiring for the water dispenser run

through the left-hand door hinge, so they must be disconnected

before removing the door.

1. Using a at-blade screwdriver, remove the cover from the top

hinge.

A. Top hinge cover screws B. Top hinge cover

A

B

2. Disconnect the water dispenser tubing located on top of the

door hinge. Firmly pull up on the clasp. Then, pull the tubing

out of the fitting.

NOTE: The water dispenser tubing remains attached to the

left-hand refrigerator door.

Remove Refrigerator Doors

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

Remove Right-Hand Door

1. Unplug refrigerator or disconnect power.

2. Keep the refrigerator doors closed until you are ready to lift

them free from the cabinet.

NOTE: Provide additional support for the refrigerator door

while the hinges are being removed. Do not depend on the

door gasket magnets to hold the door in place while you are

working.

3. Using a Phillips screwdriver, remove the cover from the

top hinge.

4. Using the TORX T25 screwdriver, remove the two screws from

the top hinge and set aside.

A. Top hinge cover screws

B. Top hinge cover

C. TORX T25 screws

D. Top hinge

A

B

C

D

12

3. Disconnect the wiring plug located on top of the door hinge.

■ Grasp each side of the wiring plug. With your left thumb,

press down to release the catch and pull the sections of

the plug apart.

NOTE: Do not remove the green ground wire. It should

remain attached to the door hinge.

4. Using the TORX T25 screwdriver, remove the two internal

screws from the top hinge and set aside.

NOTE: Provide additional support for the refrigerator door

while the hinges are being removed. Do not depend on the

door gasket magnets to hold the door in place while you are

working.

A. TORX T25 screws

B. Ground wire (Do not remove.)

A

B

5. Lift the refrigerator door from the bottom hinge pin. The top

hinge will come away with the door.

NOTE: It may not be necessary to remove the bottom hinges

and brake feet assemblies to move the refrigerator through a

doorway.

■ Only if necessary, use a TORX T25 screwdriver to remove

the bottom hinges and brake feet screws.

Replace Right-Hand Refrigerator Door

1. Set the right-hand door onto the bottom hinge pin.

2. Insert the top hinge pin into the open hole in the top of the

refrigerator door.

3. Using the three TORX T25 screws, fasten the hinge to the

cabinet. Do not tighten the screws completely.

Replace Left-Hand Refrigerator Door

IMPORTANT: Do not intertwine the water tubing and wiring

bundles when reconnecting them.

1. Set the left-hand door onto the bottom hinge pin.

2. Using the three TORX T25 screws, fasten the hinge to the

cabinet. Do not tighten the screws completely.

3. Reconnect the water dispenser tubing.

Insert the tubing rmly into the tting until it stops. Close

the clamp around the tubing. The clamp snaps into place

between the tting and the collar. Connect blue female side

with blue male side and clamp. Repeat with gray female and

gray male side.

4. Reconnect the electrical wiring.

■ Push together the two sections of the wiring plug.

Final Steps

1. Completely tighten the six internal TORX T25 screws (three

on the right-hand door hinge and three on the left-hand door

hinge).

2. Replace both top hinge covers.

13

Final Steps

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

1. Plug into a grounded 3 prong outlet.

2. Reset the controls. See the “Using the Controls” section.

3. Return all removable parts and food to the drawers.

Electrical Requirements

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Before you move your refrigerator into its nal location, it

is important to make sure you have the proper electrical

connection.

If the supply cord is damaged, it must be replaced by the

manufacturer or its service agent or a similarly qualied person.

Do not use a cord that shows cracks or abrasion damage along

its length or at either the plug or connector end.

Recommended Grounding Method

A 115 V, 60 Hz, AC only 15 or 20 A fused, grounded electrical

supply is required. It is recommended that a separate circuit

serving only your refrigerator and approved accessories

be provided. Use an outlet that cannot be turned off by a switch.

Do not use an extension cord.

IMPORTANT: If this product is connected to a GFCI (Ground

Fault Circuit Interrupter) protected outlet, nuisance tripping of the

power supply may occur, resulting in loss of cooling. Food quality

and avor may be affected. If nuisance tripping has occurred, and

if the condition of the food appears poor, dispose of the food.

Remove and Replace

Freezer Drawer Fronts

Freezer Drawer

Remove Drawer Front

1. Open the freezer drawer to its full extension.

2. Loosen the two top screws that fasten the drawer front to the

drawer glides. The two screws (one on the left-hand side and

one on the right-hand side) are located inside the drawer

front.

3. Remove the two screws at the bottom, inside the drawer front

that fasten the drawer front to the drawer glides.

4. Lift up on the drawer front to release the screws from the

drawer glide bracket slot.

A. Drawer glide bracket slots

Replace Drawer Front

1. Pull out the freezer drawer glides to their full extension.

2. Holding the drawer front by its sides, align the top screws on

the inside of the drawer front with the bracket slots on the

drawer glide.

NOTE: It helps if one person holds the drawer glides steady

while another person aligns the drawer front and inserts the

screws into the slots.

A. Drawer front screws

A

3. Tighten the top two screws of the drawer front and then

reinstall the bottom two screws.

A

14

NOTE: Before performing any type of installation or cleaning,

turn off cooling, and then disconnect the refrigerator from

the electrical source. When you have nished, reconnect the

refrigerator to the electrical source and turn on cooling. See the

“Using the Controls” section.

Water Supply Requirements

A cold water supply with water pressure between 35 and 120 psi

(241 and 827 kPa) is required to operate the water dispenser and

ice maker. If you have questions about your water pressure, call

a licensed, qualied plumber.

NOTE: If the water pressure is less than what is required, the ow

of water from the water dispenser could decrease or ice cubes

could be hollow or irregular-shaped.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out

of a reverse osmosis system and supplying the water inlet valve

of the refrigerator needs to be between 35 and 120 psi (241 and

827 kPa).

If a reverse osmosis water ltration system is connected to

your home cold water supply, the water pressure to the reverse

osmosis system needs to be a minimum of 40 to 60 psi (276 to

414 kPa).

■ Check to see whether the sediment lter in the reverse

osmosis system is blocked. Replace the lter if necessary.

■ Allow the storage tank on the reverse osmosis system to rell

after heavy use. The tank capacity could be too small to keep

up with the requirements of the refrigerator.

NOTE: Faucet-mounted reverse osmosis systems are

not recommended.

■ If your refrigerator has a water lter, it may further reduce

the water pressure when used in conjunction with a reverse

osmosis system. Remove the water lter. See the “Water

Filtration System” section.

If you have questions about your water pressure, call a licensed,

qualied plumber.

Connect the Water Supply

Read all directions before you begin.

IMPORTANT:

■ Connect to potable water supply only.

■ Plumbing must be installed in accordance with the

International Plumbing Code and any local codes and

ordinances.

■ Copper and PEX tubing connections from the household

water line to the refrigerator are acceptable and will help

avoid off-taste or odor in your ice or water. Check for leaks.

If PEX tubing is used instead of copper, we recommend the

following part numbers: W10505928RP (7 ft [2.14 m] jacketed

PEX), 8212547RP (5 ft [1.52 m] PEX), or W10267701RP

(25 ft [7.62 m] PEX).

■ Install tubing only in areas where temperatures will remain

above freezing.

Tools Needed:

Gather the required tools and parts before starting installation.

■ Flat-blade screwdriver

■ 7/16" and 1/2" open-end wrenches or two adjustable

wrenches

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

■ 1/4" nut driver

NOTE: Do not use a piercing-type or 3/16" saddle valve, which

reduces water ow and clogs easier.

Connect to Water Line

IMPORTANT: If you have turned the refrigerator on before the

water was connected, turn off the ice maker.

1. Unplug refrigerator or disconnect power.

2. Turn off main water supply. Turn on the nearest faucet until

the water stops owing.

3. Use a quarter-turn shut-off valve or the equivalent, served by

a 1/2" (12.7 mm) household supply line.

NOTE: To allow sufcient water ow to the refrigerator, a minimum

1/2

" (12.7 mm) size household supply line is recommended.

A

B

C

D

A. Sleeve

B. Nut

C. Copper tubing (to refrigerator)

D. Household supply line (1/2" [12.7 mm minimum)

4. Now you are ready to connect the copper tubing to the

shut-off valve. Use 1/4" (6.4mm) O.D. (outside diameter)

soft copper tubing to connect the shut-off valve and the

refrigerator.

■ Ensure that you have the proper length needed for the job.

Be sure both ends of the copper tubing are cut square.

■ Slip compression sleeve and compression nut onto copper

tubing as shown. Insert end of tubing into outlet end squarely

as far as it will go. Screw compression nut onto outlet end

with adjustable wrench. Do not overtighten.

A. Compression sleeve

B. Compression nut

C. Copper tubing

A

C

B

5. Place the free end of the tubing into a container or sink and

turn on main water supply to ush out tubing until water is

clear. Turn off shut-off valve on the water pipe.

NOTE: Always drain the water line before making the nal

connection to the inlet of the water valve to avoid possible

water valve malfunction.

6. Bend the copper tubing to meet the water line inlet, located

on the back of the refrigerator cabinet as shown. Leave a coil

of copper tubing to allow the refrigerator to be pulled out of

the cabinet or away from the wall for service.

15

Handle Installation and Removal

Parts Included: Refrigerator door handles (2), freezer drawer

handle (1), 1/8" (3.2 mm) hex key, spare setscrew(s)

NOTE: The freezer drawer handle is shorter than the refrigerator

door handles. Handle style may vary by model.

Install Handles

Refrigerator Doors

NOTE: Handle mounting setscrews are preinstalled inside

the handle.

1. Remove the handles from the packaging inside the

refrigerator and place them on a soft surface.

2. Open a refrigerator compartment door. On the closed

door, place a handle onto the shoulder screws so that the

setscrews are facing the adjacent door.

A. Shoulder screws

B. Setscrews inside the handle

A

B

3. Firmly push the handle toward the door until the handle base

is ush against the door.

4. While holding the handle, insert the short end of the hex key

into the upper hole and slightly rotate the hex key until key is

engaged in the setscrew.

5. Using a clockwise motion, tighten the setscrew just until

setscrew begins to contact the shoulder screw. Do not

fully tighten.

6. Repeat steps 4 and 5 to fasten the lower setscrew.

Connect to Refrigerator

Follow the connection instructions specic to your model.

1. Remove plastic cap from water valve inlet port. Attach the

copper tubing to the valve inlet using a compression nut

and sleeve as shown. Tighten the compression nut. Do not

overtighten. Conrm copper tubing is secure by pulling on

copper tubing.

2. Create a service loop with the copper tubing. Avoid kinks

when coiling the copper tubing. Secure copper tubing to

refrigerator cabinet with a “P” clamp.

A. Copper tubing

B. “P” clamp

C. Compression nut

D. Compression sleeve

A

B

C

D

3. Turn on water supply to refrigerator and check for leaks.

Correct any leaks.

4. If ice is desired, turn on the ice maker.

Complete the Installation

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

1. Plug into a grounded 3 prong outlet.

2. Flush the water system. See the “Water and Ice Dispensers”

section.

NOTE: Allow 24 hours to produce the rst batch of ice. Discard

the rst three batches of ice produced. Allow three days to

completely ll the ice storage bin.

16

7. Once both setscrews have been partially tightened as

instructed in the previous steps, fully tighten both setscrews.

IMPORTANT: When the screws feel tight, tighten them an

additional quarter turn. The handle is not properly installed

without this extra tightening.

8. Repeat steps 2 through 7 to install the other handle onto

the adjacent refrigerator door.

Freezer Drawer

1. With the drawer closed, place the handle onto the shoulder

screws so that the setscrews are facing down toward the

oor.

A. Shoulder screw

B. Setscrews inside the handle

B

A

2. Firmly push the handle toward the drawer until the handle

base is ush against the drawer.

3. Insert the short end of the hex key into the left-hand hole

and slightly rotate the hex key until key is engaged in the

setscrew.

4. Using a left-to-right motion, tighten the setscrew a quarter

turn at a time just until setscrew begins to contact the

shoulder screw. Do not fully tighten.

5. Repeat steps 3 and 4 to fasten the right-hand setscrew to

the shoulder screw.

6. Once both setscrews have been partially tightened as

instructed in the previous steps, fully tighten both setscrews.

IMPORTANT: When the screws feel tight, tighten them an

additional quarter turn. The handle is not properly installed

without this extra tightening.

7. Save the hex key and all instructions.

Remove the Handles

1. While holding the handle, insert the short end of the hex key

into a setscrew hole and slightly rotate the hex key until it is

engaged in the setscrew.

2. Using a right-to-left motion, loosen the setscrew a quarter

turn at a time.

3. Repeat steps 1 and 2 for the other setscrew. Slowly pull

the handle away from the door or drawer.

4. If necessary, use a Phillips screwdriver to remove the shoulder

screws from the door.

Refrigerator Leveling

and Door Closing

The base grille covers the adjustable brake feet and roller

assemblies located at the bottom of the refrigerator below the

freezer drawer. Before making any adjustments, remove the base

grille and move the refrigerator to its nal location.

Tools Needed: 1/4" hex driver

Tools Provided: 1/8" hex key

1. Use a 1/4" hex driver to remove both screws in base grille.

2. Remove the base grille. Using both hands, grasp the grille

rmly and pull it toward you. Open the freezer drawer to

access the brake feet.

NOTE: To allow the refrigerator to roll easier, raise the brake

feet by turning them counterclockwise. The front rollers will

be touching the oor.

3. Move the refrigerator to its nal location.

4. Using the 1/4" hex driver, lower the brake feet. Turn them

clockwise until the rollers are off the oor and both brake feet

are snug against the oor. This keeps the refrigerator from

rolling forward when opening the refrigerator doors or freezer

drawer.

IMPORTANT: If you need to make further adjustments

involving the brake feet, you must turn both brake feet the

same amount to keep the refrigerator level.

5. Use a level to make sure the refrigerator is level from side to

side and front to back.

6. Make sure the doors are even at the top and that the space

between the bottom of the refrigerator doors and the top of

the freezer drawer is even. If necessary, align the doors.

To Align the Doors:

■ Keeping both refrigerator doors closed, pull out the freezer

drawer. Locate the bottom hinge pin of the right-hand

refrigerator door. The alignment screw is inside the bottom

hinge pin.

■ Insert the short end of the 1/8" hex key (packed with the Door

Handle Installation Instructions) into the bottom hinge pin until

it is fully engaged in the alignment screw.

To raise the refrigerator door, turn the hex key to the right.

To lower the door, turn the hex key to the left.

■ Continue to turn the alignment screw until the doors are

aligned.

17

A. Bottom hinge pin

B. 1/8" hex key

B

A

7. Make sure the refrigerator is steady. If the refrigerator seems

unsteady or rolls forward when a door or drawer is pulled

open, adjust the brake feet.

To Steady the Refrigerator:

■ Open the freezer drawer. Using a 1/4" hex driver, turn both

brake feet clockwise the same amount until the brake feet are

snug against the oor. Check again. If you are not satised,

continue to adjust the brake feet by half turns of the screw

until the refrigerator does not roll forward when the drawer is

opened.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the brake feet. This makes

it easier to turn the screws. Do not push with excessive force

that tilts the refrigerator.

8. Replace the base grille by aligning the ends of the grille with

the leveling assemblies on each side and snapping the grille

into place. Use a 1/4" hex driver to reinstall screws.

FILTERS AND

ACCESSORIES

Water Filtration System

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

Replace and Install the Water Filter

The water lter should be replaced every 6 months based on a

ow rate of .50-.60 gpm (1.89 - 2.27 lpm) that lters 200 gallons

(757.1 L) of water.

To order a replacement lter, contact us. See the “Accessories”

section for information on ordering.

1. Push the water lter door to open, located bottom left of

refrigerator compartment.

2. Twist the water lter and turn 90° counterclockwise to unlock.

3. Pull the lter out of the housing.

18

4. Remove the water lter cap from the water lter being

replaced.

5. Install the water lter cap onto the new lter. Be sure to align

the arrows so the groves in lter align with ribs in lter cap.

6. Insert the lter into the housing.

7. Twist the water lter and turn 90° clockwise until it locks into

place and the arrows are aligned.

8. Push the water lter door closed.

The Water Filter Status Lights

The water lter status lights will help you know when to change

your water lter.

■ Order Filter (yellow)—It is almost time to change the

water lter. “Order” lter icon is on all of the time but

off in Showroom mode and Sabbath mode.

■ Replace Filter (red)—Replace the water lter. While you

are dispensing water, “Replace” lter icon will blink seven

times and an alert tone will sound three times.

NOTE: “Replace” lter icon will remain illuminated if the lter

is not reset on the user interface (UI).

■ Reset Filter—Touch MAX COOL and MAX ICE for

3 seconds to reset water lter. The display will do a

3-second countdown, then ash the icon and play a tone.

Install Produce Preserver

(on some models)

The produce preserver absorbs ethylene to slow the ripening

process of many produce items. As a result, certain produce

items will stay fresh longer.

Ethylene production and sensitivity varies, depending on the type

of fruit or vegetable. To preserve freshness, it is best to separate

produce with sensitivity to ethylene from fruits that produce

moderate-to-high amounts of ethylene.

Sensitivity

to Ethylene

Ethylene

Production

Apples High Very High

Asparagus Medium Very Low

Berries Low Low

Broccoli High Very Low

Cantaloupe Medium High

Carrots Low Very Low

Citrus Fruit Medium Very Low

Grapes Low Very Low

Lettuce High Very Low

Pears High Very High

Spinach High Very Low

19

Installing the Produce Preserver

For your convenience, the suction-mounted produce preserver

can be installed in either the crisper or the refrigerated drawers.

CAUTION: IRRITANT

MAY IRRITATE EYES AND SKIN. DANGEROUS FUMES

FORM WHEN MIXED WITH OTHER PRODUCTS.

Do not mix with cleaning products containing ammonia,

bleach or acids. Do not get in eyes, on skin or clothing. Do

not breathe dust. Keep out of reach of children.

FIRST AID TREATMENT: Contains potassium

permanganate. If swallowed, call a Poison Control Center or

doctor immediately. Do not induce vomiting. If in eyes, rinse

with water for 15 minutes. If on skin, rinse with water.

1. Wash the interior of a drawer with a solution of mild dish soap

and warm water and dry thoroughly.

2. Find the package containing the Produce Preserver inside the

refrigerator and install the Produce Preserver into the drawer,

according to the instructions provided in the package.

Replacing the Produce Preserver

The disposable packet(s) should be replaced every 6 months or

when the status indicator changes completely from white to red.

To order replacements, contact us. See the “Accessories” section

for information on ordering.

1. Remove the used packets from the produce preserver

housing.

2. Remove the used status indicator.

3. Install the replacement packets and status indicator using the

instructions included in the package.

Accessories

The following accessories are available for your refrigerator.

To order an accessory, contact us and ask for the part number.

In the U.S.A., visit our website

www.whirlpool.com/accessories

or call 1-800-901-2042.

In Canada, visit our webpage www.whirlpool.ca

or call 1-800-807-6777.

Affresh

®

Stainless Steel Cleaner:

In U.S.A., order Part #W10355016

In Canada, order Part #W10355016B

Affresh

®

Stainless Steel Wipes:

In U.S.A., order Part #W10355049

In Canada, order Part #W10355049B

Affresh

®

Kitchen & Appliance Cleaner:

In U.S.A., order Part #W10355010

In Canada, order Part #W10355010B

Water Filter:

In U.S.A., order Part #EDR2RXD1

In Canada, order Part #EDR2RXD1B

REFRIGERATOR USE

Opening and Closing Doors

There are two refrigerator compartment doors. The doors can

be opened and closed either separately or together. There is

a vertically hinged seal on the left refrigerator door.

■ When the left-side door is opened, the hinged seal

automatically folds inward so that it is out of the way.

■ When both doors are closed, the hinged seal automatically

forms a seal between the two doors.

A. Hinged seal

A

Using the Controls

The touch-activated controls are located above the external

dispenser and on the side of the left inner refrigerator door.

NOTE: Some models do not have the 2nd Ice Off control.

20

When adjusting temperature set points,

use the following chart as a guide:

CONDITION: TEMPERATURE ADJUSTMENT:

Refrigerator too cold Refrigerator setting 1° higher

Refrigerator too warm Refrigerator setting 1° lower

Freezer too cold Freezer setting 1° higher

Freezer too warm/

Too little ice

Freezer setting 1° lower

Max Cool

The Max Cool feature assists with periods of high refrigerator

use, full grocery loads, or temporarily warm room temperatures.

■ To turn on the Max Cool feature, press MAX COOL. When the

button is pressed, the icon will blink three times and appear

on the display screen.

■ To manually turn off the Max Cool feature, press MAX COOL

and the display will blink three times and turn off.

The Max Cool feature will remain on for 24 hours unless

manually turned off. Adjusting the refrigerator temperature

will automatically turn off the Max Cool feature.

Max Ice

The Max Ice feature assists with increasing the cooling for the

freezer compartment in order to increase ice production.

■ To turn on or off the Max Ice feature, press MAX ICE. When

the button is pressed to turn the feature on, the icon will blink

three times and appear on the display screen.

■ To manually turn off the Max Ice feature, press MAX ICE and

the display will blink three times and turn off. The Max Ice

feature will remain on for 24 hours unless manually turned off.

Adjusting the refrigerator temperature will automatically turn

off the Max Ice feature.

NOTE: Setting the freezer to a colder temperature may make

some foods, such as ice cream, harder.

Water Filter Replacement

The displays indicate the status of the water filter. To reset the

filter, press and hold MAX ICE and MAX COOL for 3 seconds.

After countdown, the “Good” icon will blink three times and

remain lit.

NOTE: The Water Filter status lights on the internal controls will

let you know when to change your water lter.

■ Order Filter (yellow): Order a replacement water lter.

■ Replace Filter (red): Replace the water lter. While you are

dispensing water, the “Replace” lter icon will ash constantly

from beginning to the end of dispensing. After 14 days

without replacing the water lter, the “Replace” lter icon will

blink seven times and an alert tone will sound three times,

at the end of dispensing. See the “Water Filtration System”

section.

NOTE: The "Replace" lter icon will remain illuminated if a

lter reset is not done.

■ Reset Filter: Press and hold MAX ICE and MAX COOL at

the same time on the Temperature Control display for 3

seconds to reset water lter. The display will do a 3-second

countdown and then ash the icon and play a tone.

Viewing and Adjusting Temperature Set Points

For your convenience, your refrigerator and freezer controls are

preset at the factory.

When you rst install your refrigerator, make sure that the

controls are still set to the recommended set points. The factory-

recommended set points are 37°F (3°C) for the refrigerator and

0°F (-18°C) for the freezer.

IMPORTANT:

■ Wait 24 hours before you put food into the refrigerator. If you

add food before the refrigerator has cooled completely, your

food may spoil.

NOTE: Adjusting the set points to a colder-than-

recommended setting will not cool the compartments any

faster.

■ If the temperature is too warm or too cold in the refrigerator

or freezer, rst check the air vents to be sure they are not

blocked before adjusting the controls.

■ The recommended settings should be correct for normal

household use. The controls are set correctly when milk or

juice is as cold as you like and when ice cream is rm.

NOTE: Areas such as a garage, basement, or porch may have

higher humidity or extreme temperatures. You may need to

adjust the temperature away from the recommended settings

to accommodate for these conditions.

■ Wait at least 24 hours between adjustments. Recheck the

temperatures before other adjustments are made.

View Temperature Set Points

Touch ▼/▲ for refrigerator or ▼/▲ for freezer to toggle through

temperature set points.

NOTE: To view temperature in degrees Celsius, touch

and hold the °F-°C button for 3 seconds and the temperature

display will change. To return to Fahrenheit, touch and hold

°F-°C for 3 seconds and the temperature display will change.

To activate Temperature mode for Pantry Drawer, touch

DRAWER and toggle through four optional temperature settings:

Meats, Deli-Cheese, Assorted, and Drinks. The display will show

the temperature set point of the selected setting for the pantry

drawer.

Recommended Refrigerator Temperature

Recommended Freezer Temperature

Adjust Temperature Set Points

Refrigerator set point range: 33°F to 45°F (1°C to 7°C)

Freezer set point range: -6°F to 5°F (-22°C to -15°C)

1. Touch ▼/▲ to adjust the Refrigerator zone. The display will

show the temperature set point of the selected compartment

as shown.

2. When the temperature is in the range of Freeze Shield, the

display will light up. Freeze Shield is active at the coldest

freezer set point.

La page charge ...

Whirlpool WRF953CIHB Manuel utilisateur

Whirlpool WRF953CIHB Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents