Whirlpool Cabrio WTW8600YW1 Mode d'emploi

Whi

cabr,o

TOP-LOADING

HIGH EFFICIENCY

LOW-WATER WASHER

USE AND CARE GUIDE

LAVEUSE HAUTE

EFFICACITI_ A FAIBLE

CONSOMMATION D'EAU

AVEC CHARGEMENT

PAR LE DESSUS

GUIDE D'UTILISATION

ET D'ENTRETIEN

Table of Contents

WASHER SAFETY ......................................................... 2

WHAT'S NEW UNDER THE LiD? ................................. 3

CONTROL PANELAND FEATURES......................................4

Dispensers.......................................................................5

CYCLE GUIDE ............................................................... 6

USING YOUR WASHER ................................................ 8

Using Laundry Product Dispensers...............................9

Starting YourWasher......................................................9

WASHER MAINTENANCE .............................................. 11

TROUBLESHOOTING ...................................................... 13

WARRANTY ........................................................................18

ASSISTANCE OR SERVICE ...........................Back Cover

Table des Mati_res

S¢:CURIT¢: DE LA LAVEUSE ...................................... 19

QUOI DE NEUF SOUS LE COUVERCLE? ................ 20

TABLEAU DE COMMANDE

ET CARACTC:RISTIQUES .......................................... 21

Distributeurs.................................................................. 22

GUIDE DES PROGRAMMES ...................................... 23

UTILISATION DE LA LAVEUSE .................................. 26

Utilisation de distributeurs

de produits de lessive...................................................27

Mise en marche de la laveuse......................................27

ENTRETIEN DE LA LAVEUSE ........................................30

DF:PANNAGE ...................................................................... 32

GARANTIE ..........................................................................39

ASSISTANCE OU SERVICE ..............Couverture artiste

Para una version en espanol, visite www.whirlpool.com

Designed to use only HE High Efficiency

detergents.

Congue uniquement pour une utilisation

avec des d6tergents HE Haute efficacit6.

W10405142A

W10405143A =SP

WASHER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all

safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or

"WARNING." These words mean:

You can be killed or seriously injured if you don't

immediately follow instructions.

You can be killed or seriously injured if you don't

follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you

what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injuryto persons when using the washer, follow basic precautions,

including the following:

[] Read all instructions before using the washer.

[] Do not wash articles that have been previously cleaned

in, washed in, soaked in, or spotted with gasoline,

dry-cleaning solvents, other flammable, or explosive

substances as they give off vapors that could ignite or

explode.

[] Do not add gasoline, dry=cleaning solvents, or other

flammable, or explosive substances to the wash water.

These substances give off vapors that could ignite or

explode.

[]

Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been used

for 2 weeks or more. HYDROGEN GAS IS

EXPLOSIVE. Ifthe hot water system has not been

used for such a period, before using the washing

machine, turn on all hot water faucets and let the water

flow from each for several minutes. This will release

any accumulated hydrogen gas. As the gas is

flammable, do not smoke or use an open flame during

Do not allow children to play on or in the washer. Close

supervision of children is necessary when the washer is used

near children.

Before the washer is removed from service or discarded,

remove the door or lid.

[] Do not reach intothe washer if the drum, tub or agitator is

moving.

[] Do not install or store the washer where itwill be exposed to

the weather.

[] Do not tamper with controls.

[] Do not repair or replace any part of the washer or attempt any

servicing unless specifically recommended in this manual or in

published user=repair instructionsthat you understand and

have the skills to carry out.

[] See "Electrical Requirements" located in the installation

instructions for grounding instructions.

this time.

SAVE THESE INSTRUCTIONS

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

2

WHAT'S NEW UNDER THE LID?

Cleaaiag with Less Automatic Load Size Sensing

Traditional agitator-style

washer

Low-water washer

The most striking difference in your new washer is the low-water

washplate wash system. The washer automatically adjusts the

water level to the load size--no water level selector is needed.

Once you start the cycle, the lid will lock, and the washer will

begin the sensing process to determine the correct water level

for the load.

You will hear the motor turn the basket in short pulses to

thoroughly wet the load. This low-water wash method uses

less water and energy compared to a traditional agitator-style

washer.

Choosiag the Right Detergent

Use only High Efficiency detergents. The package will be

marked "HE" or "High Efficiency." Low-water washing creates

excessive sudsing with a regular non-HE detergent. Using

regular detergent will likely result in longer cycle times and

reduced rinsing performance. It may also result in component

failures and noticeable mold or mildew. HE detergents are made

to produce the right amount of suds for the best performance.

Follow the manufacturer's instructions to determine the amount

of detergent to use.

Use only High Efficiency (HE) detergent.

Load garments in loose heaps evenly around the washplate.

Do not load garments directly over the center of the washplate;

when loaded, the center of the washplate should be visible.

Concentrated Cleaniag

Low-water cleaning means concentrated cleaning. Rather

than diluting detergent as done in an agitator-style washer,

this washer delivers the detergent directly to the soils.

NormM Sounds You Can Expect

At different stages of the wash cycle, you may hear sounds and

noises that are different from those of your previous washer.

For example, you may hear a clicking and hum at the beginning

of the cycle, as the lid lock goes through a self-test. There

will be different kinds of humming and whirring sounds as the

washplate moves the load. And sometimes, you may hear

nothing at all, as the washer determines the correct water level

for your load or allows time for clothes to soak.

As the washer dampens and moves the load, the level of the

garments will settle in the basket. This is normal, and does not

indicate that more garments should be added.

IMPORTANT: You will not see a washer basket full of water

as with your past agitator-style washer. It is normal for some of

the load to be above the water line.

3

CONTROL P EL FEATURES

POWER T

/

Not all features and cycles are available on all models.

O POWER BUTTON

Press to turn the washer ON. Pressing once while the

washer is on will cancel the current cycle, pressing twice

will turn the washer OFF.

WASH CYCLE KNOB

Turn the Wash Cycle knob to select a cycle for your laundry

load. See "Cycle Guide" for detailed descriptions of cycles.

TIME/STATUS DISPLAY

The Estimated Time Remaining display shows the time

required for the cycle to complete. Factors such as load size

and water pressure may affect the time shown in the display.

Overloading, unbalanced loads, or excessive suds may

cause the washer to adjust the cycle time, as well.

If you have set a delay start to the cycle, the Estimated

Time Remaining display will show the delay time adjusted.

When the cycle is complete, the DONE indicator will light

until the lid is opened.

The Lid Lock indicator lights up when the lid is locked

and cannot be opened. Ifyou need to open the lid, press

START/PAUSE. The lid will unlock once the washer

movement has stopped. This may take several minutes

if the load was spinning at high speed. Press START/PAUSE

again to restart the cycle.

ECO MONITOR

Your washer is specially designed to conserve energy

and water. Each cycle, along with any selected options,

will result in different energy and water usage. To use the

Eco Monitor, choose the best cycle for the load being

washed, then adjust temperature and spin speed options

to improve the energy usage within that cycle.

START/PAUSE BUTTON

Press to start the selected cycle; press again to pause

a cycle.

CYCLE SIGNAL BUTTON

Use this option to adjust volume of the signal that sounds

at end of cycle. A louder signal is helpful in removing items

as soon as cycle is complete.

CYCLE OPTIONS

You may add or remove options for each cycle. Note that

not all options can be used with all cycles, and some are

preset to work with certain cycles.

ECOBOOST

The EcoBoost option allows you to increase your energy

savings on your wash cycles. When this option is used,

4

the wash cycle will use cooler wash water than the

selected cycle and may increase the spin speed for

faster drying.

EXTRA RINSE

This option can be used to automatically add a second

rinse to most cycles.

FABRIC SOFTENER DISPENSER

Press this button to set the Fabric Softener dispenser to

automatically add liquid fabric softener to the load at the

correct time.

O CYCLE MODIFIERS

Whenyou select a cycle, its default settings will light up.

SOIL LEVEL

Soil level (wash time) is preset for each wash cycle. As

you press the Soil Level pad, the cycle time (minutes) will

increase or decrease in the Estimated Time Remaining

display and a different wash time will appear.

For most loads, use the soil level that is preset with the

cycle you have chosen. For heavily soiled and sturdy

fabrics, press SOIL LEVEL to select more wash time, if

needed. For lightly soiled and delicate fabrics, press SOIL

LEVEL to select less wash time, if needed. A lower soil

level setting will help reduce tangling and wrinkling.

SPIN SPEED

This washer automatically selects the spin speed based

on the cycle selected. The preset speeds can be changed.

Not all spin speeds are available with all cycles.

• Faster spin speeds mean shorter dry times, but may

increase wrinkling in your load.

• Slower spin speeds mean less wrinkling, but will leave

your load more damp.

WASH TEMP

Temperature Control senses and maintains uniform water

temperatures by regulating incoming hot and cold water.

Select a wash temperature based on the type of fabric

and soils being washed. For best results and following

the garment label instructions, use the warmest wash

water safe for your fabric.

• Warm and hot water may be cooler than what your

previous washer provided.

• Even for cold wash settings, some warm water may

be added to the washer to maintain a minimum

temperature.

High Efficiency "HE" detergent dispenser

Add liquid or powdered HE detergent to this dispenser for

your main wash cycle.

Use only High Efficiency (HE) detergent.

Liquid chlorine bleach dispenser

This dispenser holds up to 3/4 cup (180 mL) liquid chlorine

bleach. The bleach will be automatically diluted and

dispensed at the optimum time during the the wash cycle.

This dispenser cannot dilute powdered bleach.

NOTE: Fill dispenser only with liquid chlorine bleach.

Liquid fabric softener dispenser

Pour measured liquid fabric softener into the liquid fabric

softener dispenser, if desired. It will dispense automatically

at the optimum time when the Fabric Softener option is

selected.

• Use only liquid fabric softener in this dispenser.

5

CYCLE GUIDE

Settings and options shown in bold are default settings for that cycle.

For best fabric care, choose the cycle that best fits the load being washed.

If using the Eco Monitor, adjust the temperature and spin speed within that cycle to improve energy usage.

Not all cycles and options are available on all models.

_n

temsto,,,ash: cycle: wash

= Temp*:

Lightly soiled Quick

garments Wash

Machine-wash

silks, hand-wash

fabrics and wool

Athletic and

high-performance

wear

Handwash/

Delicate

Active

Wear

Normally soiled

sheets

No-iron fabrics

Cottons, linens,

and mixed garment

loads

Bright or darkly

colored cottons,

linens, casual and

mixed loads

Large items such as

sleeping bags, small

comforters, jackets

Sturdy fabrics,

colorfast items

Soiled white

fabrics

Sheets

Perm Press/

Casual

Normal

Hot

Warm

Cool

Cold

Warm

Cool

Cold

Hot

Warm

Cool

Cold

Hot

Warm

Cool

Cold

Hot

Warm

Cool

Cold

Hot

Warm

Cool

Cold

Spin Soil Available

Speed: Leveh Options:

High Heavy Extra Rinse

Medium Normal Fabric Softener

Low Medium

Light

Medium Heavy Extra Rinse

Low Normal Fabric Softener

Medium

Light

Use this cycle to wash small loads of

2-3 lightly soiled garments that are needed

in a hurry. This cycle combines a fast

agitation, a shortened wash time, and

a high-speed spin to shorten drying times.

Use this cycle for machine washable delicate

garments. This cycle uses intermittent wash

action with cool water and slow spin to

gently care for fine washables and avoid

shrinkage. Place small items in mesh bags

High

Medium

Low

High

Medium

Low

High

Medium

Low

High

Medium

_before washing.

Heavy

Normal

Medium

Light

Heavy

Normal

Medium

Light

Heavy

Normal

Medium

Light

Heavy

Normal**

Medium

Light

Extra Rinse

EcoBoost

Fabric Softener

Extra Rinse

EcoBoost

Fabric Softener

Extra Rinse

EcoBoost

Fabric Softener

Extra Rinse

EcoBoost

Fabric Softener

Use this cycle to wash loads of no-iron

fabrics such as sport shirts and other active

wear.

Use this cycle to wash bed sheets. This

cycle uses extra water and a special wash

action to reduce tangling.

Use this cycle for lightly soiled office wear.

The cycle uses a warm wash, a cooldown,

and medium spin speeds for better wrinkle

performance.

Use this cycle to clean normally soiled

cottons and mixed fabric loads. Default

settings can be adjusted as needed.

Cold Wash/

Clean Care

Bulky

Items

Heavy

Duty

Cold

Hot

Warm

Cool

Cold

Hot

Warm

Cool

Cold

Whites Hot

Warm

Cool

Cold

High

Medium

Low

Medium

Low

High

Medium

Low

High

Medium

Low

Heavy

Normal

Medium

Light

Heavy

Normal

Medium

Light

Heavy

Normal

Medium

Light

Heavy

Normal

Medium

Light

Extra Rinse

EcoBoost

Fabric Softener

Extra Rinse

EcoBoost

Fabric Softener

Extra Rinse

EcoBoost

Fabric Softener

Extra Rinse

EcoBoost

Fabric Softener

This cycle uses cold water wash and a

concentrated detergent solution to gently

lift out stains and care for fabrics. Settings

may be adjusted as desired, but must use

only cold water settings.

This cycle is designed for oversized items

that do not easily absorb water, such as

comforters, pillows, and poly-filled jackets.

The cycle uses an initial soak to thoroughly

saturate the item(s).

Use this cycle for heavily soiled or

sturdy cotton items. This cycle combines

high-speed wash action, longer wash

time, and extra high-speed spin to shorten

drying times. Adjust temperature settings

as needed.

This cycle adds liquid chlorine bleach to

the load at the proper time for improved

whitening of soiled white fabrics.

* Wash temperatures vary according to the chosen cycle setting. All cycle settings use a cold rinse temperature.

** Not all models default to the same Soil Level setting. Some models will default to Medium on this cycle.

6

CYCLE GUIDE

Settings and options shown in bold are default settings for that cycle.

For best fabric care, choose the cycle that best fits the load being washed.

If using the Eco Monitor, adjust the temperature and spin speed within that cycle to improve energy usage.

Not all cycles and options are available on all models.

Itemsto wash:, Cycle: Wash

Temp*:

No clothes in

washer

Heavily soiled

fabrics

Clean

Washer

with

Affresh ®

Soak Warm

Cool

Cold

Spin

Speed:

i:¸sou :

Level:

Heavy

Normal

Medium

Light

. CydeDeta s:

Options:

EcoBoost

For models with separate cycle knob positions for Rinse & Spin and Drain & Spin:

Swimsuits, items Rinse & High EcoBoost

that need rinsing Spin Medium Fabric Softener

only Low

Wet load of Drain & High

clothes Spin Medium

Low

For models with a Rinse/Drain & Spin cycle position:

Rinse D ;_:_! High

& Spin Medium

Low

High

Medium

Low

EcoBoost

Fabric Softener

Swimsuits, items

that need rinsing

only

Wet load of

clothes

R _se/Drain

& Spin

Use this cycle every 30 washes to keep the

insideof your washer fresh and clean. This

cycle uses a higher water level. Use with

AFFRESH®washer cleaner tablet or liquid

chlorine bleach to thoroughly clean the

insideof your washer. This cycle should not

be interrupted. See "Cleaning Your Washer."

IMPORTANT: Do not place garments or

other items inthe washer during the Clean

Washer with AFFRESH ®cycle. Use this

cycle with an empty wash tub.

Use this cycle to soak small spots of

set-in stains on fabrics. After time has

expired, washer will drain, but will not

spin and a tone will sound. To set a

follow-up cycle, add additional detergent

and select a cycle based on fabric type.

This cycle uses a high-speed spin.

For some fabrics, you may wish to set

the spin speed to a lower setting.

Use this cycle to spin excess water

out of a load. This cycle drains the water

and spins at a high speed. Spin speed

is adjustable.

This cycle uses a high-speed spin.

For some fabrics, you may wish to set

the spin speed to a lower setting.

To select, choose Rinse/Drain & Spin

and turn off Extra Rinse. Use this cycle

to spin excess water out of a load. This

cycle drains the water and spins at a

high speed. Spin speed is adjustable.

* Wash temperatures vary according to the chosen cycle setting. All cycle settings use a cold rinse temperature.

7

USING YOUR WASHER

Fire Hazard

Never place items in the washer that are

dampened with gasoline or other flammable

fluids.

No washer can completely remove oil.

Do not dry anything that has ever had any type of

oil on it (including cooking oils).

Doing so can result in death, explosion, or fire.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

1, Sort and prepare your laundry

• Empty pockets. Loose change, buttons, or any small

object can pass under the washplate and become trapped,

causing unexpected sounds.

• Sort items by recommended cycle, water temperature,

and colorfastness.

• Separate heavily soiled items from lightly soiled.

• Separate delicate items from sturdy fabrics.

• Do not dry garments if stains remain after washing; heat

can set stains into fabric.

• Treat stains promptly.

• Close zippers, fasten hooks, tie strings and sashes.

Remove non-washable trim and ornaments.

• Mend rips and tears to avoid further damage to items

during washing.

Helpful Tips:

• When washing water-proof or water-resistant items, load

evenly. See "Cycle Guide" for tips and more information

on using the Bulky Items cycle.

• Use mesh bags to help prevent tangling when washing

delicate or small items.

• Turn knits inside out to avoid pilling. Separate lint-takers

from lint-givers. Synthetics, knits, and corduroy fabrics

will pick up lint from towels, rugs, and chenille fabrics.

NOTE: Always read and follow fabric care labels instructions

to avoid damage to your garments.

8

Load garments in loose heaps evenly

around the washplate. Do not load

garments directly over the center

of the washplate; when loaded, the

center of the washplate should be

visible. Try mixing different sized

garments to reduce tangling.

IMPORTANT: Garments need to move freely for best cleaning

and to reduce wrinkling and tangling.

Usiag Lauadry Product Dispensers

Add HE detergent to dispenser

Detergent dispenser

kj _

Add a measured amount of HE

detergent into detergent dispenser.

IMPORTANT: Use only High Efficiency detergents. The package

will be marked "HE" or "High Efficiency." Low-water washing

creates excessive sudsing with a regular non-HE detergent.

Using regular detergent will likely result in longer cycle times and

reduced rinsing performance. It may also result in component

failures and noticeable mold or mildew. HE detergents are made

to produce the right amount of suds for the best performance.

Follow the manufacturer's instructions to determine the amount

of detergent to use.

NOTE: If using an Oxi laundry boost product, add to the

detergent dispenser.

HELPFUL TIP: See "Washer Maintenance" for information on

recommended method of cleaning washer dispensers.

to dispenser

Fabric

Pour a measured amount of liquid Softener

Dispenser

fabric softener into dispenser; always

follow manufacturer's directions for correct amount of

fabric softener based on your load size. Then select

Fabric Softener option.

IMPORTANT: Fabric Softener option must be selected

to ensure proper distribution at correct time in cycle.

Do not overfill or dilute. Overfilling dispenser will cause

fabric softener to immediately dispense into washer.

If Extra Rinse option is selected, fabric softener will be

dispensed in the last rinse.

NOTE: Do not use liquid fabric softener dispenser balls

in this washer. They will not dispense correctly.

Starting Your Washer

6, Press POWER to turn on washer

POWER

Do not overfill, dilute, or use more than 3/4 cup (180 mL).

Do not use color-safe bleach or Oxi products in the same

cycle with liquid chlorine bleach.

9

7, Select cycle

CASUAL

SHEETS

ACTIVE WEAR

,_d:, s

DELICATE

NORMAL

CLEAN CARE

BULKY ITEMS

HEAVY DUTY

WHITES

QUICKWASH

RINSE CLEAN

DRAIN SOAK WASHER

& SPIN with8[_8_

I Est+Time Remaining

Turn cycle knob to choose

your wash cycle. Estimated

Time Remaining will light

up with a cycle time. You

may notice time adjusting

during the cycle. This is normal.

If you do not want to begin a cycle immediately, you may

choose the DELAY WASH option.

To choose a delay time:

1. Press DELAY WASH button to select desired delay time.

2. Press START/PAUSE to set the delay. The delay countdown

has started when the START/PAUSE light stops blinking.

To cancel delaying a cycle:

1. Press START/PAUSE again to begin a wash cycle

immediately.

IMPORTANT: When delaying a cycle, use liquid HE detergent

only in the dispenser. Powdered detergents may absorb

moisture from a previous cycle and clump before the wash

cycle begins.

8, Select cycle modifiers, if desired

Heavy

Normal

Medium

L ght

@

Soil

Level

Hot

[_iHigh ii Warm

Medium ii/ Cool

LiLow Jcold

@

Spin Wash

Speed Temp

Once you select a cycle, the default settings for that cycle will

be lit. Press the cycle modifiers buttons to change the Soil

Level, Spin Speed, and Wash Temp, if desired. Not all settings

are available with all cycles.

NOTE: Always read and follow fabric care labels instructions

to avoid damage to your garments.

10

Wash Temp : Suggested Fabrics

Hot

Some cold water is added to save Whites and pastels

energy. This will be cooler than Durable garments

your hot water heater setting. Heavy soils

Warm

Some cold water will be added, so Bright colors

this may be cooler than what your Moderate to light soils

previous washer provided.

Cool

Warm water is added to assist in Dark colors that

soil removal and to help dissolve bleed or fade

detergents. Light soils

Cold

Warm water may be added to Dark colors that

assist in soil removal and to help bleed or fade

dissolve detergents. Light soils

9. Select cycle options

On

EcoBoost Off

Extra Fabric

Rinse Softener

Dispenser

Select any other cycle options you may wish to add, if not

previously set. Some cycles will automatically add certain

options such as Extra Rinse. These may be turned off,

if desired.

NOTE: Not all options are available with all cycles.

1 0. Press START/PAUSE to begin

wash cycle

START

Pause

@

Press the START/PAUSE button to start the wash cycle. When

the cycle has finished, the DONE indicator will light and the end

of cycle signal will sound (if set). Promptly remove garments

when cycle is done to avoid odor, reduce wrinkling, and rusting

of metal hooks, zippers, and snaps.

Unlocking the lid to add garments

If you need to open the lid to add 1 or 2 missed garments:

Press START/PAUSE; the lid will unlock once the washer

movement has stopped. This may take several minutes if the

load was spinning at high speed. Then close lid and press

START/PAUSE again to restart the cycle.

If lid is left open for more than 10 minutes the water will pump

out.

WASHER &INTENANCE

WATER iNLET HOSES

Replace inlet hoses after 5 years of use to reduce the risk

of hose failure. Periodically inspect and replace inlet hoses

if bulges, kinks, cuts, wear, or leaks are found.

When replacing your inlet hoses, mark the date of

replacement on the label with a permanent marker.

NOTE: This washer does not include inlet hoses. See

the "Installation Instructions" for more information.

CLEANING YOUR WASHER

Keep your washer as clean and fresh as your

clothes. To keep washer interior odor-free, follow this

recommended cleaning procedure after every 30 washes:

1. Make sure the washer is empty.

2. Using recommended AFFRESH ®washer cleaner,

add one tablet to washer drum.

OR

If using liquid chlorine bleach, add 3/4 cup (180 mL)

to liquid chlorine bleach dispenser.

/

f

I

f

IMPORTANT: Do not add detergent to CLEAN

WASHER with AFFRESH ®cycle. Do not use more than

recommended amount of bleach to avoid damaging

product over time.

3. Close washer lid.

4. Press POWER.

5. Select CLEAN WASHER with AFFRESH ®cycle.

6. Press START/PAUSE. Water will pour into washer

for a moment and pause, lid will lock, then cycle

will continue.

NOTE: For best results, do not interrupt cycle. If cycle

must be interrupted, press START/PAUSE twice and run a

RINSE & SPIN cycle to ensure cleaner or bleach have been

rinsed from washer.

To clean exterior:

1. Use a soft, damp cloth or sponge to wipe up any spills.

2. Use all-purpose surface cleaner, if needed.

IMPORTANT: To avoid damaging the washer's finish,

do not use abrasive products.

('- CLEANING YOUR DISPENSERS

You may find laundry product residue leftover in your

dispensers. To remove residue, wipe with a damp cloth

and towel dry.

f NON=USE AND VACATION CARE

Operate your washer only when you are home.

If moving, or not using your washer for a period of time,

follow these steps:

1. Unplug or disconnect power to washer.

2. Turn off water supply to washer, to avoid flooding

due to water pressure surge.

r

WINTER STORAGE CARE

iMPORTANT: To avoid damage, install and store washer

where it will not freeze. Because some water may stay in

hoses, freezing can damage washer. If storing or moving

during freezing weather, winterize your washer.

To winterize washer:

1. Shut off both water faucets; disconnect and drain water

inlet hoses.

2. Put 1 qt. (1 L) of R.V.-type antifreeze in basket and run

washer on RINSE & SPIN cycle for about 30 seconds to

mix antifreeze and remaining water.

3. Unplug washer or disconnect power.

11

TRANSPORTING YOUR WASHER

1. Shut off both water faucets. Disconnect and drain water

inlet hoses.

2. if washer will be moved during freezing weather, follow

WINTER STORAGE CARE directions before moving.

3. Disconnect drain from drain system.

4. Unplug power cord.

5. Place inlet hoses inside washer basket.

6. Drape power cord and drain hose over the console

and secure with masking tape.

7. Place foam packing ring from original shipping materials

back inside washer, ifyou do not have packing ring,

place heavy blankets or towels into basket opening.

Close lid and place tape over lid and down front of

washer. Keep lid taped until washer is placed in

new location.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

REINSTALLING/USING WASHER AGAIN

To reinstall washer after non-use, vacation, winter storage

or moving:

1. Refer to "Installation Instructions" to locate, level, and

connect washer.

2. Before using again, run washer through the following

recommended procedure:

To use washer again:

1. Flush water pipes and hoses. Reconnect water inlet

hoses. Turn on both water faucets.

2. Plug in washer or reconnect power.

3. Run washer through BULKY iTEMS cycle to clean

washer and remove antifreeze, if used. Use only HE

High Efficiency detergent. Use half the manufacturer's

recommended amount for a medium-size load.

12

TROUBLESHOOTING

First try the solutions suggested here or visit our website at www.whirlpool.com/help

for assistance and to possibly avoid a service call.

Vibration, rocking, or Feet may not be in contact with the Front and rear feet must be in firm contact with floor, and washer

"walking" floor and locked, must be level to operate properly. Jam nuts must be tight

against the bottom of the cabinet.

Washer may not be level. Check floor for flexing or sagging. Ifflooring is uneven, a 3/4"

(19 mm) piece of plywood under your washer will reduce sound.

Vibration during spinning

or washer stopped with

all dial lights flashing

Load could be unbalanced.

See "Level the Washer" in the "Installation Instructions'.

Load garments in loose heaps evenly around the washplate.

Do not load garments directly over the center of the washplate.

Adding wet items to washer or adding more water to basket

could unbalance washer.

Avoid washing single items. Balance a single item such as a

rug or jeans jacket with a few extra items. Ifthe dial is flashing,

redistribute the load, close the lid, and press START/PAUSE.

Use Bulky Items cycle for oversized, non-absorbent items

such as comforters or poly-filled jackets. Other items are

not appropriate for Bulky Items cycle. See "Cycle Guide".

Item or load not suitable for selected cycle. See "Cycle Guide"

and "Using Your Washer" in this "Use and Care Guide".

Clicking or metallic

noises

Gurgling or humming

Humming

Objects caught in washer

drain system.

Washer may be

draining water.

The washer is sensing the

load size.

Empty pockets before washing. Loose items such as coins

could fall between basket and tub or may block pump.

It may be necessary to call for service to remove items.

It is normal to hear metal items on clothing such as metal snaps,

buckles, or zippers touch against the stainless steel basket.

It is normal to hear the pump making a continuous humming sound

with periodic gurgling or surging asfinn amounts of water are

removed during the spin/drain cycles.

You may hear the hum of the sensing spins after you have started

the washer. This is normal. Sensing spins will take severn minutes

before water is added to the washer.

Check the following for

proper installation:

Washer not level.

Fill hoses not attached tightly.

Fill hose washers

Drain hose connection

Check household plumbing for leaks

or clogged sink or drain.

Washer not loaded as

recommended.

Water may splash off basket if washer is not level.

Tighten fill-hose connection.

Make sure all four fill hose flat washers are properly seated.

Pull drain hose from washer cabinet and properly secure it to

drainpipe or laundry tub.

Do not place tape over drain opening.

Water can backup out of a clogged sink or drainpipe. Check

all household plumbing for leaks (laundry tubs, drain pipe,

water pipes, and faucets.)

An unbalanced load can cause basket to be out of alignment

and cause water to splash off tub. See "Using Your Washer"

for loading instructions.

Not enough water

in washer

Load not completely covered

in water.

This is normal operation for an HE low-water washer. The load will

not be completely unden._/ater.The washer senses load sizes and

adds correct amount of water for optimal cleaning. See "What's

New under the Lid."

IMPORTANT: Do not add more water to washer. Adding water lifts

the garments off the washplate, resulting in less effective cleaning, j

13

TROUBLESHOOTING

Check for proper water supply.

Washer won't run or fill,

washer stops working

k.

Both hoses must be attached and have water flowing to

inlet valve.

Both Hot and Cold water faucets must be turned on.

Check that inlet valve screens have not become clogged.

Check for any kinks in inlet hoses, which can restrict water flow.;)

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

mfyou experience Possibme Causes Somution

Washer won't run or fill,

washer stops working

(cont.)

Check proper electrical supply.

Normal washer operation.

Washer may be tightly packed.

Not using HE detergent or using too

much HE detergent.

Plug power cord into a grounded 3 prong outlet.

Do not use an extension cord.

Ensure there is power to outlet.

Reset a tripped circuit breaker. Replace any blown fuses.

NOTE: If problems continue, contact an electrician.

Lid must be closed for washer to run.

Washer will pause during certain phases of cycle.

Do not interrupt cycle.

Washer may be stopped to reduce suds.

The washer senses the dry load with short spins that may take

2 to 3 minutes before water is added. You may hear the hum

of the spins. This is normal.

Remove several items, rearrange load evenly around the

washplate. Do not load garments directly over the center

of the washplate. Close lid and press START/PAUSE.

Add only I or 2 additional garments after washer has started.

Do not add more water to the washer.

Only use HE detergent. Suds from regular detergents can slow

or stop the washer. Always measure detergent and following

detergent directions based on your load requirements.

To remove suds, cancel cycle. Select DRAIN & SPIN. Select your

cycle. Press START/PAUSE. Do not add more detergent.

Washer not draining/ Empty pockets and use garment bags Small items may have been caught in pump or between basket

spinning, loads are still for small items, and tub, which can slow draining.

W et j

14

TROUBLESHOOTING

Washer not draining/

spinning, loads are

still wet (cont.)

Incorrect or wrong

wash or rinse

temperatures

Load not rinsed

Sand, pet hair, lint, etc.

on load after washing

Load is tangling

k.

Using cycles with a lower spin speed.

Washer may be tightly packed or

unbalanced.

Check plumbing for correct drain

hose installation. Drain hose extends

into standpipe farther than 4.5" (114

am).

Not using HE detergent or using too

much HE detergent.

Check for proper water supply.

Energy-saving controlled

wash temperatures.

Check for proper water supply.

Not using HE detergent or using too

much HE detergent.

Washer may be tightly packed.

Fabric softener option not selected.

Heavy sand, pet hair, lint, and

detergent or bleach residues

may require additional rinsing.

Washer not loaded as recommended.

Cycles with lower spin speeds remove less water than cycles

with high spin speeds. Use the recommended cycle/speed spin

for your garment.

Tightly packed loads may not allow the washer to spin correctly,

leaving the load wetter than normal. Evenly arrange the wet load

for balanced spinning. Select DRAIN & SPIN to remove excess

water. See "Using Your Washer" for loading recommendations.

Check drain hose for proper installation. Use drain hose

form and securely attach to drainpipe or tub. Do not tape

over drain opening. Lower drain hose if the end is higher than 96"

(2.4 m) above the floor. Remove any clogs from drain hose.

Suds from regular detergent or using too much detergent can

slow or stop draining or spinning. Use only HE detergent.

Always measure and follow detergent directions for your

load. To remove extra suds, Select RINSE & SPIN. Do not

add detergent.

Make sure hot and cold inlet hoses are not reversed.

Both hoses must be attached to both washer and faucet, and

have both hot and cold water flowing to inlet valve.

Check that inlet valve screens are not clogged.

Remove any kinks in hoses.

Energy Star *_qualified washers use cooler wash and rinse

water temperatures than traditional topqoad washers. This

includes cooler hot and warm washes.

Make sure hot and cold inlet hoses are not reversed.

Both hoses must be attached and have water flowing to the

inlet valve.

Both hot and cold water faucets must be on.

Inlet valve screens on washer maybe clogged.

Remove any kinks in the inlet hose.

The suds from regular detergent can cause the washer

to operate incorrectly.

Use only HE detergent. Be sure to measure correctly.

Always measure detergent and follow detergent directions

based on load size and soil level.

The washer is less efficient at rinsing when load is tightly

packed.

Load garments in loose heaps evenly around the washplate. Do

not load garments directly over the center of the washplate.

Use cycle designed for the fabrics being washed.

Add only 1 or 2 additional garments after washer has started.

When using fabric softener, be sure the Fabric Softener option

is selected.

Add an Extra Rinse to the selected cycle.

Load garments in loose heaps evenly around the washplate.

Do not load garments directly over the center of the washplate.

Reduce tangling by mixing types of load items. Use the

recommended cycle for the type of garments being washed.

J

15

TROUBLESHOOTING

First try the solutions suggested here or visit our website at www.whirlpool.com/help

for assistance and to possibly avoid a service call.

Load is tangling (cont.) Wash action and/or spin speed too

fast for load.

Not cleaning or Wash load not completely

removing stains covered in water.

Added more water to washer.

Washer not loaded as recommended.

Odors

Not using HE detergent or using too

much HE detergent.

Not using correct cycle for fabric type.

Not using dispensers.

Not washing like colors together.

Monthly maintenance not done as

recommended.

Not using HE detergent or using too

much HE detergent.

Fabric Damage Sharp items were in pockets during

wash cycle.

Strings and straps could have tangled.

Htemsmay have been damaged before

washing.

Fabric damage can occur if the load is

tightly packed.

Select a cycle with a slower wash action and slower spin speed.

Note that items will be wetter than when using a higher speed spin.

Garment care instructions may not

have been followed.

16

Load garments in loose heaps evenly around washplate. Do

not load garments directly over the center of the washplate.

Load items should move freely during wash to avoid damage,

Use cycle designed for the fabrics being washed.

Add only 1 or 2 additional garments after washer has started.

Always read and follow garment manufacturer's care label

instructions. See the "Cycle Guide" to match your load with

the best cycle.

Washer senses load size and adds correct amount of water.

This is normal and necessary for clothes to move.

Do not add more water to washer. Adding water lifts the

garments off the washplate, resulting in less effective cleaning.

Load garments in loose heaps evenly around the washplate. Do

not load garments directly over the center of the washplate.

Add only 1 or 2 additional garments after washer has started.

The suds from regular detergent can prevent washer from

operating correctly.

Use only HE detergent. Be sure to measure correctly.

Always measure detergent and follow detergent directions

based on load size and soil level.

Use a higher soil level cycle option and warmer wash

temperature to improve cleaning.

Hfusing Quick Wash cycle (on some models), wash only a

few items.

Use Whites and Heavy Duty cycle for tough cleaning.

See the "Cycle Guide" to match your load with the best cycle.

Use dispensers to avoid chlorine bleach and fabric softener

staining.

Load dispensers before starting a cycle.

Avoid overfilling.

Do not add products directly onto load.

Wash like colors together and remove promptly after the cycle

is complete to avoid dye transfer.

Run the Clean Washer with AFFRESH ®cycle after every 30

washes. See "Cleaning Your Washer" in "Washer Maintenance".

Unload washer as soon as cycle is complete.

Use only HE detergent. Be sure to measure correctly.

Always follow the detergent directions.

See "Cleaning your Washer" section.

Empty pockets, zip zippers, and snap or hook fasteners before

washing to avoid snags and tears.

Tie all strings and straps before starting wash load.

Mend rips and broken threads in seams before washing.

TROUBLESHOOTING

r

First try the solutions suggested here or visit our website at www.whirlpool.com/help

for assistance and to possibly avoid a service call.

Fabric Damage (cont.)

Incorrect dispenser

operation

Liquid chlorine bleach may have been

added incorrectly.

Clogged dispensers or laundry

products dispensing too soon.

Liquid chlorine bleach not

used in dispenser.

Do not pour liquid chlorine bleach directly onto load. Wipe up

bleach spills.

Undiluted bleach will damage fabrics. Do not use more than

recommended by manufacturer.

Do not place load items on top of bleach dispenser when

loading and unloading washer.

Do not overfill dispenser. Overfilling causes immediate dispensing.

Always select Fabric Softener option to assure proper dispensing.

Load dispensers before starting a cycle.

Htis normal for small amounts of water to be remain in dispenser at

the end of the cycle.

Homes with low water pressure may result in residual powder in the

dispenser. To avoid, select a warmer wash temperature if possible,

depending on your load.

Use only liquid chlorine bleach in the Bleach dispenser.

oL (overloaded)

appears in display

uL (unbalanced load)

appears in display

LF (too long to fill)

appears in display

Ld (too long to drain

water ) appears in

display

HC (Hot and Cold

hoses reversed)

appears in display

Sd (Excess suds)

appears in display

Load too large.

Load not balanced. The washer is

running a load-balance correction

routine.

Washer taking too long to fill.

Drain extends more than

4.5" (114 mm)into standpipe.

Washer taking too long to drain

water. Drain extends more than

4.5" (114 mm)into standpipe.

Hot and cold inlet hoses have been

installed incorrectly.

Excessive suds in washer. Washer is

running a suds reduction routine.

Hfan overload is detected, the washer will drain any water and

detergent in the washer. Remove several items and add HE

detergent. Close lid and press START/PAUSE.

Allow the machine to continue. Hfthe dial is flashing and the

machine has stopped, redistribute the load, close the lid, and

press START/PAUSE.

Check plumbing for correct drain hose installation. Use drain

hose form and attach securely to drainpipe or tub. Do not tape

over drain opening. See "hstallation hstructions'.

Check plumbing for correct drain hose installation. Use drain

hose form and attach securely to drainpipe or tub. Do not tape

over drain opening.

Lower drain hose if the end is higher than 96" (2.4 m) above

the floor. Remove any clogs from drain hose. See "Installation

Instructions".

This code will appear at the end of the wash cycle to indicate

that cold water hose is connected to the hot water inlet and hot

water hose is connected to the cold water inlet.

Allow the washer to continue. Use only HE detergent.

Always measure detergent, and base detergent quantity on

load size. Follow detergent manufacturer's instructions. If the

dial is flashing, reselect your desired cycle using a cold wash

temperature, and press START/PAUSE. Do not add detergent.

dL (Lid cannot lock) An item in the load may be keeping Check for items directly under the lid.

appears in display the lid from locking.

lid (Lid opened) Washer lid left open. Close the lid to clear the display. If the lid is left open for more

appears in display than 10 minutes, the cycle will reset and water in the washer

will drain.

dU (Lid cannot unlock) Objects on washer lid prevent it from Remove objects, such as a basket of laundry, from the top of

appears in display unlocking, the washer.

F## code (F-type System error code. Press START/PAUSE once to clear the code. Then press

error code) appears START/PAUSE again to restart washer. If code appears again,

in display call for service.

17

WHIRLPOOLCORPORATIONLAUNDRYWARRANTY

LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or

furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter "Whirlpool") will pay for Factory Specified Parts

and repair labor to correct defects in materials or workmanship that existed when this major appliance was purchased. Service must be

provided by a Whirlpool designated service company. YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY

SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. This limited warranty is valid only in the United States or Canada and applies

only when the major appliance is used in the country in which it was purchased. Proof of original purchase date is required to obtain

service under this limited warranty.

ITEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is

used in a manner that is inconsistent to published user or operator instructions and/or installation instructions.

2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or

repair house fuses, or to correct house wiring or plumbing.

3. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty

coverage.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.

5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage

results from defects in materials or workmanship and is reported to Whirlpool within 30 days from the date of purchase.

6. Pick up and delivery. This major appliance is intended to be repaired in your home.

7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized Whirlpool servicer is not available.

9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance

with Whirlpool's published installation instructions.

10. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered, or

cannot be easily determined.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR

A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces

do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This

warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow

the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This

warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

If outside the 50 United States and Canada, contact your authorized Whirlpool dealer to determine if another warranty applies.

If you think you need repair service, first see the "Troubleshooting" section of the Use & Care Guide. If you are unable to resolve the

problem after checking "Troubleshooting," additional help can be found by checking the "Assistance or Service" section or by calling

Whirlpool. In the U.S.A., call 1-800-253-1301. In Canada, call 1-800-807-6777. 7/08

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your major appliance

to better help you obtain assistance or service if you ever need it.

You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the product.

Dealer name

Address

Phone number

Model number

Serial number

Purchase date

18

p p

$ECURXTE DE LA LA USE

Votre s_curit_ et celle des autres est tr_s importante,

Nous donnons de nombreux messages de securit6 importants dans ce manuel et sur votre appareil menager.

Assurez=vous de toujours lire tousles messages de securit6 et de vous y conformer.

Voici le symbole d'alerte de s6curit&

Ce symbole d'alerte de securit6 vous signale les dangers potentiels de deces et de blessures graves

& vous et & d'autres.

Tous les messages de securit6 suivront le symbole d'alerte de s6curit6 et le mot "DANGER" ou

"AVERTISSEMENT". Ces mots signifient :

Risque possible de d_c_s ou de blessure grave si

vous ne suivez pas irnm6diaternent les instructions,

Risque possible de d_c_s ou de blessure grave

si vous ne suivez pas les instructions.

Tousles messages de s6curit6 vous diront quel est le danger potentiel et vous disent comment r6duire le risque de

blessure et ce qui peut se produire en cas de non-respect des instructions.

IMPORTANTES INSTRUCTIONS DE SC:CURITI-

AVERTISSEMENT : Pour reduire les risques d'incendie, de choc electrique ou de blessures Iors de I'utilisation de la

laveuse, suivre les precautions fondamentales dont les suivantes :

[] Lire toutes les instructionsavant d'utiliser la laveuse.

[] Ne pas laver des articles qui ont et6 nettoyes ou

laves avec de I'essence ou imbibes d'essence,

solvants de nettoyage & sec, ou autres substances

inflammables ou explosives; ces substances

peuvent emettre des vapeurs susceptibles de

s'enflammer ou d'exploser.

[] Ne pas ajouter d'essence, solvant de nettoyage &

sec ou autre produit inflammable ou explosif dans

I'eau de lavage. Ces substances peuvent 6mettre

des vapeurs susceptibles de s'enflammer ou

d'exploser.

[] Dans certaines conditions, de I'hydrogene gazeux

peut se former dans un circuit d'eau chaude qui n'a

pas 6t6 utilise pendant 2 semaines ou plus. LE GAZ

HYDROGI_NE EST EXPLOSIBLE. Si le circuit d'eau

chaude n'a pas et6 utilise pendant une telle periode,

avant d'utiliser la laveuse, ouvrir tousles robinets

d'eau chaude et laisser I'eau s'ecouler pendant

plusieurs minutes par chaque robinet. Ceci

permettra I'evacuation de I'hydrogene gazeux

accumule. Comme ce gaz est inflammable, ne pas

fumer ou utiliser une flamme nue au cours de cette

p6riode.

[] Ne pas laisser des enfants jouer sur ou & I'int6rieur de la

laveuse. Bien surveiller les enfants Iorsque la laveuse est

utilisee & proximit6 d'enfants.

[] Avant de mettre la laveuse au rebut ou hors de service,

enlever la porte ou le couvercle.

[] Ne pas tenter d'atteindre un article & I'interieur de la cuve de

la laveuse Iorsque le tambour, la cuve ou I'agitateur est en

mouvement.

[] Ne pas installer ou remiser cette laveuse & un endroit oQ elle

serait exposee aux intemperies.

[] Ne pas modifier les organes de commande.

[] Ne pas reparer ou remplacer un composant quelconque de

la laveuse, ni entreprendre une operation de service, si ce

n'est specifiquement recommande dans ce manuel ou dans

un manuel d'instructions de reparations destine & I'utilisateur;

il est alors essentiel que la personne concernee comprenne

ces instructions et soit competente pour les executer.

[] Pour les instructionsde liaison #,la terre, voir "Specifications

electriques" dans les instructions d'installation.

CONSERVEZ CES INSTRUCTIONS

Avertissements de la proposition 65 de I'Etat de Californie :

AVERTISSEMENT : Ce produit contient au moins un produit chimique connu par I'Etat de Californie pour _tre & I'origine de

cancers.

AVERTISSEMENT : Ce produit contient au moins un produit chimique connu par I'Etat de Califomie pour 6tre & I'origine de

malformations et autres deficiences de naissance.

19

QUOI DE NEUF $0U$ LE COU ERCLE?

Laver avec moins d'eau

Laveuse traditionnelle

de type agitateur

Laveuse a faible

consommation d'eau

La nouveaut6 la plus remarquable de cette nouvelle laveuse

est son systeme de lavage a faible consommation d'eau avec

plateau de lavage. La laveuse ajuste automatiquement le

niveau d'eau en fonction de la taille de la charge - nul besoin

de s61ecteur de niveau d'eau.

Charger les v_tements sans les tasser et de fa£;on uniforme

le long du plateau de lavage. Ne pas placer les v@ements

directement au centre du plateau de lavage - celui-ci doit

6tre visible.

D6tection automatique de taille

de charge

Une fois que I'on d6marre le programme, le couvercle se

verrouille et la laveuse entame un processus de d6tection pour

d6terminer le niveau d'eau appropri6 a la charge.

Vous entendrez le moteur faire tourner le panier par de brefs

mouvements d'impulsion pour bien imbiber la charge. Cette

m6thode de lavage avec faible consommation d'eau utilise moins

d'eau et d'6nergie qu'une laveuse traditionnelle de type agitateur.

Choix du d6tergent appropri6

Utiliser uniquement des d6tergents Haute efficacit6.

Uemballage portera la mention "HE" ou "High Efficiency"

(haute efficacit6). Un lavage avec faible consommation

d'eau produit un exces de mousse avec un d6tergent non HE

ordinaire. II est probable que I'utilisation d'un d6tergent ordinaire

prolongera la dur6e des programmes et r6duira la performance

de ringage. Ceci peut aussi entrainer des d6faillances des

composants et une moisissure perceptible. Les d6tergents HE

sont congus pour produire la quantit6 de mousse ad6quate

pour le meilleur rendement. Suivre les recommandations

du fabricant pour d6terminer la quantit6 de d6tergent a utiliser.

Utiliser uniquement un dOtergent Haute efficacitO (HE).

Nettoyage eoneentr6

ke systeme de lavage a faible consommation d'eau signifie un

lavage concentr6. Plut6t que de diluer du d6tergent comme

dans une laveuse de type agitateur, cette laveuse libere le

d6tergent directement sur les endroits souill6s.

Sons normaux pr6visibles

Au cours des diffOrents stades du programme de lavage, vous

entendrez peut-_tre des bruits que votre laveuse pr6c6dente

ne produisait pas. Par exemple, vous entendrez peut-6tre

un cliquetis au d6but du programme Iorsque le systeme de

verrouillage du couvercle effectue un test automatique. On

entendra diff@ents bourdonnements et bruits de frottements

rythmiques a mesure que I'impulseur d6place la charge. Parfois,

il est possible que la laveuse soit completement silencieuse,

Iorsqu'elle d6termine le niveau d'eau ad6quat ou qu'elle laisse

tremper les v_tements.

A mesure que la laveuse imbibe et d6place la charge, les

v_tements se tassent dans le panier. Ceci est normal et ne

signifie pas que I'on doive rajouter des v_tements.

IMPORTANT : Le panier de la laveuse ne sera pas rempli d'eau,

comme avec votre pr6c6dente laveuse de type agitateur. II est

normal qu'une partie de la charge d6passe du niveau d'eau.

2O

La page est en cours de chargement...

Whirlpool Cabrio WTW8600YW1 Mode d'emploi

Ce manuel convient également à

Whirlpool Cabrio WTW8600YW1 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents