Halsey Taylor RWM8.H Le manuel du propriétaire
- Catégorie
- Articles sanitaires
- Taper
- Le manuel du propriétaire
Ce manuel convient également à
97436C (Rev. B - 8/01)
RWM8*1H
PAGE 1
HALSEY TAYLOR OWNERS MANUAL
USES HFC-134A REFRIGERANT
FIG. 1
SEE FIG.4
8, 9
SEE FIG.3
21
18
35
16
17
23
22
6
33
10
3,4,5
7
11
12
32
34
2
SEE
DETAIL
ABOVE
19
1
13,
14,
15
20
36
37,38,39
30
31
42
40
41
43
97436C (Rev. B - 8/01)
RWM8*1H
PAGE 2
FIG. 2
FINISHED FLOOR
PISO ACABADO
PLANCHER FINI
MOUNTING BOX
ROUGH-IN
* RECOMMENDED HEIGHT FOR ADULTS. DECREASE HEIGHT FOR CHILDREN.
* ALTURA RECOMENDADA PARA ADULTOS. REDUZCA PARA LOS NIÑOS.
* HAUTEUR RECOMMANDÉE POUR LES ADULTES. INSTALLEZ PLUS BAS POUR LES ENFANTS.
D = ELECTRICAL OUTLET LOCATION
UBICACIÓN DE LA TOMA DE ELECTRICIDAD
EMPLACEMENT DE LA PRISE DE COURANT
E = INSURE PROPER VENTILATION BY MAINTAINING 4" (102mm) (MIN.) CLEARANCE FROM CABINET LOUVERS TO WALL.
ASEGURE UNA VENTILACIÓN ADECUADA MANTENIENDO UN ESPACIO E 4" (102mm) (MÍN.) DE HOLGURA ENTRE LA
REJILLA DE VENTILACIÓN DEL MUEBLE Y LA PARED
ASSUREZ-VOUS UNE BONNE VENTILATION EN GARDANT 4" (102mm) (MIN.) ENTRE LES ÉVENTS DE LENCEINTE ET LE
MUR.
F = POWER CORD 1-1/2FEET (457mm) LONG
CABLE ELÉCTRICO DE 1½ PIE, 457 mm DE LARGO
CORDON DALIMENTATION 1-1/2' (457mm)
LEGEND/LEYENDA/LÉGENDE
A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED COPPER TUBE CONNECT STUB 1-1/2
IN. (38 mm) OUT FROM WALL SHUT OFF BY OTHERS
SE RECOMIENDA UBICAR EL TUBO CORTO DE CONEXIÓN AL TUBO DE COBRE SIN CHAPAR DE 3/8" DE
DIÁM. EXT. A 1-1/2" (38 mm) FUERA DE LA LLAVE DE PASO EN LA PARED COLOCADA POR TERCEROS.
EMPLACEMENT RECOMMANDÉ D'ALIMENTATION EN EAU PAR TUBE EN CUIVRE NON PLAQUÉ DE 3/8 PO.
(9,5 mm) D.E. CONNECTANT UNE TUYAUTERIE DE 1-1/2 PO. (38 mm) DEPUIS LE ROBINET D'ARRÊT
FOURNI PAR D'AUTRES.
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4 O.D. DRAIN
UBICACIÓN RECOMENDADA PARA EL DRENAJE DE SALIDA DE AGUA, DE 1¼ DE DIÁMETRO.
EMPLACEMENT RECOMMANDÉ POUR LE DRAIN DE D.E. 1-1/4" DE SORTIE DEAU.
C = 1-1/4 TRAP NOT FURNISHED**
PURGADOR DE 1¼ NO PROPORCIONADO**
SIPHON 1-1/4 NON FOURNI**
97436C (Rev. B - 8/01)
RWM8*1H
PAGE 3
FIG. 3
Stream height is factory set at 35 PSI. If supply pressure varies greatly from this,
remove items 24 and 25 and adjust screw on item 27. Clockwise adjustment will
raise stream and counter-clockwise adjustment will lower stream. For best adjust-
ment, stream should hit basin approximately 6-1/2" (165mm) from bubbler.
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
INSTALLATION OF COOLER AND TRAP
1) Hang the unit from the mounting box by placing the tabs from the upper backside of the basin over top of the
upper flange on the mounting box, and mount trap, as shown in Figure 2.
NOTE: Mounting Box and trap MUST be supported securely. Add fixture support carrier if wall will not provide adequate support.
IMPORTANT:
5-1/2 in. (140mm) dimension from wall to centerline of trap must be maintained for proper fit.
2) Secure cooler in place by positioning fastening clips as shown in Figure 2 - Detail B.
3) Install straight valve for 3/8" O.D. unplated copper tube.
4) Remove the access panel on the underside of the cooler and set it aside.
5) Connect water inlet line--See Note 4 of General Instructions.
6) Remove the slip nut and gasket from the trap and install them on the cooler waste line making sure that the
end of the waste line fits into the trap. Assemble the slip nut and gasket to the trap and tighten securely.
START UP
Also See General Instructions
7) Replace the front panel and secure by retightening all screws.
FIG. 4
WRAPPER
27
25
2624
28
29
CORRECT STREAM HEIGHT
97436C (Rev. B - 8/01)
RWM8*1H
PAGE 4
ITEMIZED PARTS LIST
ITEM NO. PART NO.
DESCRIPTION
31517C
27321C
30699C
70018C
31490C
70009C
50186C
51544C
15012C
62152C
66202C
35960C
35958C
35768C
35959C
66501C
40041C
45431C
27230C
70208C
31513C
66505C
55996C
27239C
40089C
40048C
15005C
61313C
40169C
50986C
40038C
40619C
27093C
27292C
27331C
27094C
See Color Table
50144C
70184C
70418C
40043C
50105C
50074C
70817C
Power Cord
Fan Bracket
Fan Blade
Hex Nut - Fan Blade
Fan Motor
Screw (Fan Motor)
Shroud - Fan
Bubbler
Nipple - Bubbler
Condenser
Drier
Compressor Serv. Pak EM65
Overload
Cover - Relay
Relay
Heat Exchanger
Tailpipe Assy (8 Gal)
Precooler Assy (13 Gal)
Basin - Stainless Steel
Screw - Basin Mtg.
Cold Control
Evaporator Assembly
Strainer
Bracket - Precooler
Cover
Button
Retaining Nut
Regulator
Hex Nut
Regulator Holder
Strainer - Beehive
Ferrule - Tailpipe
Angle - Front Corners
Bracket - Basin Mounting
Frame - Back/Bottom
Bracket - Front
Wrapper
Grommet - Compressor Mtg.
Hair Pin - Cotter
Washer
Locknut
Tailpipe Gasket
Tailpipe Gasket
Fitting - Elbow 1/4 Stem
1
2
3
4
5
6
7
8
9
10
11
12*
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
*INCLUDES RELAY & OVERLOAD. IF UNDER WARRANTY, REPLACE
WITH SAME COMPRESSOR USED IN ORIGINAL ASSEMBLY.
NOTE: All correspondence pertaining to any of the above water cool-
ers or orders for repair parts MUST include Model No. and Serial No. of
cooler, name and part number of replacement part.
COLOR TABLE
PANEL COLOR
Item No. 36
Part No.
Almond Vinyl
Platinum Vinyl
Stainless Steel
Slate Vinyl
26942C
26943C
26948C
26949C
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
2222 CAMDEN COURT
OAK BROOK, IL 60523
630.574.3500
PRINTED IN U.S.A.
-
1
-
2
-
3
-
4
Halsey Taylor RWM8.H Le manuel du propriétaire
- Catégorie
- Articles sanitaires
- Taper
- Le manuel du propriétaire
- Ce manuel convient également à
dans d''autres langues
- English: Halsey Taylor RWM8.H Owner's manual
Documents connexes
-
Halsey Taylor HBW.G Le manuel du propriétaire
-
-
-
-
-
-
-