Yamaha HTR-5140 Manuel utilisateur

Marque: Yamaha

Modèle: HTR-5140

Catégorie: Destinataire

Taper: Manuel utilisateur

Ce manuel convient également à

RX-V495

Printed in Malaysia ID

V343260

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

HTR-5140

Natural Sound AV Receiver

Ampli-Tuner Audio-Video

OWNER’S MANUAL

MODE D’EMPLOI

U C A T

05HTR-5140-e/f cv1/4 6/22/99, 2:41 PM1

SAFETY INSTRUCTIONS

1 Read Instructions – All the safety and operating instructions

should be read before the unit is operated.

2 Retain Instructions – The safety and operating instructions

should be retained for future reference.

3 Heed Warnings – All warnings on the unit and in the

operating instructions should be adhered to.

4 Follow Instructions – All operating and other instructions

should be followed.

5 Water and Moisture – The unit should not be used near

water – for example, near a bathtub, washbowl, kitchen

sink, laundry tub, in a wet basement, or near a swimming

pool, etc.

6 Carts and Stands – The unit should be used only with a

cart or stand that is recommended by the

manufacturer.

6A A unit and cart combination should be moved

with care. Quick stops, excessive force, and

uneven surfaces may cause the unit and cart

combination to overturn.

7 Wall or Ceiling Mounting – The unit should be mounted to a

wall or ceiling only as recommended by the manufacturer.

8 Ventilation – The unit should be situated so that its location

or position does not interfere with its proper ventilation. For

example, the unit should not be situated on a bed, sofa,

rug, or similar surface, that may block the ventilation

openings; or placed in a built-in installation, such as a

bookcase or cabinet that may impede the flow of air

through the ventilation openings.

9 Heat – The unit should be situated away from heat sources

such as radiators, stoves, or other appliances that produce

heat.

10 Power Sources – The unit should be connected to a power

supply only of the type described in the operating

instructions or as marked on the unit.

11 Power-Cord Protection – Power-supply cords should be

routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying

particular attention to cords at plugs, convenience

receptacles, and the point where they exit from the unit.

12 Cleaning – The unit should be cleaned only as

recommended by the manufacturer.

13 Nonuse Periods – The power cord of the unit should be

unplugged from the outlet when left unused for a long

period of time.

14 Object and Liquid Entry – Care should be taken so that

objects do not fall into and liquids are not spilled into the

inside of the unit.

15 Damage Requiring Service – The unit should be serviced

by qualified service personnel when:

A. The power-supply cord or the plug has been

damaged; or

B. Objects have fallen, or liquid has been spilled into the

unit; or

C. The unit has been exposed to rain; or

D. The unit does not appear to operate normally or exhibits

a marked change in performance; or

E. The unit has been dropped, or the cabinet damaged.

16 Servicing – The user should not attempt to service the unit

beyond those means described in the operating

instructions. All other servicing should be referred to

qualified service personnel.

17 Power Lines – An outdoor antenna should be located away

from power lines.

18 Grounding or Polarization – Precautions should be taken

so that the grounding or polarization is not defeated.

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to alert

you to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may

be of sufficient magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert you to the presence

of important operating and maintenance

(servicing) instructions in the literature

accompanying the appliance.

WARNING

TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE THIS

UNIT TO RAIN OR MOISTURE.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

05HTR-5140-e/f-1 6/22/99, 2:04 PM2

English

19 For US customers only:

Outdoor Antenna Grounding – If an outside antenna is

connected to this unit, be sure the antenna system is

grounded so as to provide some protection against voltage

surges and built-up static charges. Article 810 of the

National Electrical Code, ANSI/NFPA 70, provides

information with regard to proper grounding of the mast

and supporting structure, grounding of the lead-in wire to

an antenna discharge unit, size of grounding conductors,

location of antenna discharge unit, connection to grounding

electrodes, and requirements for the grounding electrode.

FCC INFORMATION (for US customers only)

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s Consumer

Electronics Group want you to get the most out of your

equipment by playing it at a safe level. One that lets the sound

come through loud and clear without annoying blaring or

distortion – and, most importantly, without affecting your

sensitive hearing.

Since hearing damage from loud sounds is often

undetectable until it is too late, YAMAHA and the

Electronic Industries Association’s Consumer

Electronics Group recommend you to avoid

prolonged exposure from excessive volume levels.

Compliance with FCC regulations does not guarantee

that interference will not occur in all installations. If this

product is found to be the source of interference, which

can be determined by turning the unit “OFF” and “ON”,

please try to eliminate the problem by using one of the

following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient

the antenna. If the antenna lead-in is 300 ohm ribbon

lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfac-

tory results, please contact the local retailer authorized

to distribute this type of product. If you can not locate

the appropriate retailer, please contact Yamaha

Electronics Corp., U.S.A. 6660 Orangethorpe Ave,

Buena Park, CA 90620.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved by

Yamaha may void your authority, granted by the FCC,

to use the product.

2. IMPORTANT : When connecting this product to

accessories and/or another product use only high

quality shielded cables. Cable/s supplied with this

product MUST be used. Follow all installation instruc-

tions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE : This product has been tested and found to

comply with the requirements listed in FCC Regula-

tions, Part 15 for Class “B” digital devices. Compliance

with these requirements provides a reasonable level of

assurance that your use of this product in a residential

environment will not result in harmful interference with

other electronic devices.

This equipment generates/uses radio frequencies and,

if not installed and used according to the instructions

found in the users manual, may cause interference

harmful to the operation of other electronic devices.

Note to CATV system installer:

This reminder is provided to call the CATV system

installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in

particular, specifies that the cable ground shall be

connected to the grounding system of the building, as

close to the point of cable entry as practical.

EXAMPLE OF ANTENNA GROUNDING

MAST

GROUND

CLAMP

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810–20)

GROUNDING CONDUCTORS

(NEC SECTION 810–21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250. PART H)

ELECTRIC

SERVICE

EQUIPMENT

NEC

– NATIONAL ELECTRICAL CODE

05HTR-5140-e/f-1 6/22/99, 2:04 PM3

• Indoor FM Antenna

• Antenne FM intérieure

• AM Loop Antenna

• Cadre-antenne AM

• Antenna adapter

(U.S.A. and Canada models only)

• Adaptateur d’antenne

(Modèles pour les Etats-Unis et le

Canada seulement)

• Batteries (size AAA, R6, UM-4)

• Piles (taille AAA, R6, UM-4)

SUPPLIED ACCESSORIES

ACCESSOIRES FOURNIS

• After unpacking, check that the following parts are included.

• Après le déballage, vérifier que les pièces suivantes sont incluses.

• Remote control transmitter

• Télécommande

05HTR-5140-e/f-1 6/22/99, 2:04 PM4

English

● 5-Channel Power Amplification

Minimum RMS Output Power

<0.04% THD, 20 Hz – 20 kHz>

Main: 60 W + 60 W (8 Ω)

Center:60 W (8 Ω)

Rear: 60 W + 60 W (8 Ω)

<0.07% THD, 1 kHz>

Main: 70 W + 70 W (8 Ω)

Center:70 W (8 Ω)

Rear: 70 W + 70 W (8 Ω)

● Digital Sound Field Processor

● Dolby Digital Decoder

● Dolby Pro Logic Surround Decoder

● CINEMA DSP: Theater-like Sound

Experience by the Combination of Dolby

Surround and YAMAHA DSP Technology

SUPPLIED ACCESSORIES........................................... 4

FEATURES .................................................................... 5

CAUTION ....................................................................... 6

●Introduction

FEATURES OF SOUND EFFECTS............................... 7

CONTROLS AND THEIR FUNCTIONS ......................... 9

●Preparation

SPEAKER SETUP ....................................................... 14

CONNECTIONS........................................................... 16

ADJUSTMENTS

BEFORE USING THIS UNIT .................................. 23

●Basic Operation

BASIC OPERATIONS .................................................. 28

TUNING OPERATIONS ............................................... 32

SETTING THE SLEEP TIMER.....................................37

●Information about DSP

USING THE DIGITAL SOUND FIELD

PROCESSOR (DSP) .............................................. 38

●Advanced Information

ADJUSTMENTS

IN THE “SET MENU” MODE...................................44

●Remote Control Transmitter

REMOTE CONTROL TRANSMITTER......................... 46

SETUP CODES ........................................................... 53

TROUBLESHOOTING .................................................54

SPECIFICATIONS ....................................................... 57

LIST OF MANUFACTURER’S CODES...................... 113

FEATURES

CONTENTS

● 6-Channel External Decoder Input for DTS

and other future formats

● Automatic Input Balance Control for

Dolby Pro Logic Surround

● Test Tone Generator for Easier Speaker

Balance Adjustment

● Speaker Output Mode Changing

Capability

● 40-Station Random Access Preset Tuning

● Automatic Preset Tuning

● Preset Station Shifting Capability

(Preset Editing)

● Video Signal Input/Output Capability

● SLEEP Timer

● Universal Remote Control

Transmitter with Preset Manufacturer

Codes

05HTR-5140-e/f-1 6/22/99, 2:04 PM5

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1. To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2. Install this unit in a cool, dry, clean place – away from

windows, heat sources, sources of excessive vibration,

dust, moisture and cold. Avoid sources of humming

(transformers, motors). To prevent fire or electrical shock,

do not expose the unit to rain or water.

3. Never open the cabinet. If something drops into the set,

contact your dealer.

4. Do not use force on switches, controls or connection wires.

When moving the unit, first disconnect the power plug and

the wires connected to other equipment. Never pull the

wires themselves.

5. The openings on the unit cover assure proper ventilation of

the unit. If these openings are obstructed, the temperature

inside the unit will rise rapidly. Therefore, avoid placing

objects against these openings, and install the unit in a

well-ventilated area to prevent fire and damage.

Be sure to allow a space of at least 20 cm behind, 20 cm

on the both sides and 30 cm above the top panel of the unit

to prevent fire and damage.

6. The voltage used must be the same as that specified on

this unit. Using this unit with a higher voltage than

specified is dangerous and may result in fire or other

accidents. YAMAHA will not be held responsible for any

damage resulting from use of this unit with a voltage other

than specified.

7. Digital signals generated by this unit may interfere with

other equipment such as tuners, receivers or TVs. Move

this unit farther away from such equipment if interference is

observed.

8. Always set the VOLUME control to “

” before starting the

audio source play. Increase the volume gradually to an

appropriate level after playback has been started.

9. Do not attempt to clean the unit with chemical solvents; this

might damage the finish. Use a clean, dry cloth.

10. Be sure to read the “TROUBLESHOOTING” section

regarding common operating errors before concluding that

the unit is faulty.

11. When not planning to use this unit for long periods of time

(ie., vacation, etc.), disconnect the AC power plug from the

wall outlet.

12. To prevent lightning damage, disconnect the AC power

plug and disconnect the antenna cable when there is an

electrical storm.

13. Grounding or polarization – Precautions should be taken so

that the grounding or polarization of an appliance is not

defeated.

14. AC outlet

Do not connect audio equipment to the AC outlet on the

rear panel if that equipment requires more power than the

outlet is rated to provide.

15. Voltage Selector (China and General Models only)

The voltage selector on the rear panel of this unit must

be set for your local main voltage BEFORE plugging

into the AC main supply.

Voltages are 110/120/220/240 V AC, 50/60 Hz.

This unit is not disconnected from the AC power source as

long as it is connected to the wall outlet, even if this unit

itself is turned off. This state is called the standby mode. In

this state, this unit is designed to consume a very small

quantity of power.

FREQUENCY STEP switch

(China and General Models only)

Because the interstation frequency spacing differs in

different areas, set the FREQUENCY STEP switch (located

at the rear) according to the frequency spacing in your area.

Before setting this switch, disconnect the AC power plug of

this unit from the AC outlet.

IMPORTANT

Please record the serial number of this unit in the space

below.

MODEL:

Serial No.:

The serial number is located on the rear of the unit.

Retain this Owner’s Manual in a safe place for future

reference.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

FOR CANADIAN CUSTOMERS

To prevent electric shock, match wide blade of plug to wide

slot and fully insert.

This Class B digital apparatus complies with Canadian

ICES-003.

05HTR-5140-e/f-1 6/22/99, 2:04 PM6

English

FEATURES OF SOUND EFFECTS

Welcome to the exciting world of digital home entertainment.

This unit is one of the most complete and advanced AV

receivers available. Some of the more advanced features may

not be familiar to you, but they are easy to use. State-of-the-art

technologies such as Dolby Digital and Digital Theater Systems

(DTS) may be new to your home, but you have probably

experienced the amazing realism they bring to feature films in

theaters around the world.

To make the listening experience even more enjoyable, this unit

includes a number of exclusive, digitally created listening

environments known as digital sound fields. Choosing a sound

field program is like transporting yourself to such venues as an

outdoor arena, a European church, or a cozy jazz club. Take

some time now to read more about these features and enjoy

the new experiences this unit brings to your home theater.

Digital Sound Field Processing

What is it that makes live music so good? Today’s advanced

sound reproduction technology lets you get extremely close to

the sound of a live performance, but the chances are that you’ll

still notice something missing — the acoustic environment of

the live concert hall. Extensive research into the exact nature

of the sonic reflections that create the ambience of a large hall

has made it possible for YAMAHA engineers to bring you this

same sound to your listening room, so you’ll feel all the sound

of a live concert.

Furthermore, our technicians, armed with sophisticated

measuring equipment, have even made it possible to capture

the acoustics of a variety of actual concert halls, theaters, etc.

from around the world, to allow you to accurately re-create any

one of these live performance environments, all in your own

home.

Dolby Pro Logic Surround

Dolby Pro Logic Surround has been used in movie theaters

since the mid-seventies. It has also been available in home

entertainment systems since the late eighties and continues to

be a popular format for home theater systems. It uses four

discrete channels and five speakers to reproduce realistic and

dynamic sound effects: two main channels (left and right), a

center channel for dialog, and a rear channel for special sound

effects. The rear channel reproduces sound within a narrow

frequency range.

Most video tapes and laser discs include Dolby Pro Logic

Surround encoding, as do many TV and cable broadcasts. The

Dolby Pro Logic Surround decoder built into this unit employs a

digital signal processing system that stabilizes each channel for

even more accurate sound positioning than is available with

standard analog processors.

Dolby Digital

The built-in Dolby Digital decoder leads you into a totally new

sound experience.

Dolby Digital is a new generation of multi-channel digital audio

technology, or the newest spatial sound processing format

developed for 35 mm-film movies by employing a new kind of

low bit-rate audio coding.

Dolby Digital is a digital surround sound system that provides

completely independent multi-channel audio to listeners. In

multi-channel form, Dolby Digital provides 5 full-range channels

in what is sometimes referred to as a “3/2” configuration: three

front channels (left, center and right), plus two surround

channels. A sixth bass-only effect channel is also provided for

output of LFE (low frequency effect), or low bass effects that

are independent of other channels. This channel is counted as

0.1, thus giving rise to the term 5.1 channels in total.

Compared to Dolby Pro Logic, which is referred to a “3/1”

system (left front, center, right front and just one surround

channel), Dolby Digital features two surround channels, called

stereo or split surrounds, each offering the same full-range

fidelity as the three front channels.

Sound of wide dynamic range reproduced by the 5 full-range

channels provides listeners with excitement that has never

been experienced before. Precise sound orientation by

discrete digital sound processing expands the realism that the

original movie possesses.

LD and DVD are home audio/video program source that could

benefit from Dolby Digital. In the near future, Dolby Digital will

also be applied to DBS, CATV and HDTV. The ongoing release

of Dolby Stereo Digital theatrical films now underway will

provide an immediate source of Dolby Digital encoded video

software.

Introduction

05HTR-5140-e/f-1 6/22/99, 2:04 PM7

Manufactured under license from Dolby Laboratories Licensing

Corporation. “DOLBY”, “PRO LOGIC”, and the double-D symbol

are trademarks of Dolby Laboratories Licensing Corporation.

The following original functions make the surround-sound effect

of Dolby Digital become the most suitable for your audio

system and the listening conditions.

CINEMA DSP: Dolby Surround + DSP

The Dolby Surround sound system shows its full ability in a

large movie theater, because movie sounds are originally

designed to be reproduced in a large movie theater using many

speakers. It is difficult to create a sound environment similar to

that of a movie theater in your listening room, because the

room size, materials of inside walls, the number of speakers,

etc. of your listening room are very different from those of a

movie theater.

YAMAHA DSP technology made it possible to present you with

nearly the same sound experience as that of a large movie

theater in your listening room by compensating for the lack of

presence and dynamics in your listening room with its original

digital sound fields combined with the Dolby Surround sound

system.

CINEMA DSP

The YAMAHA “CINEMA DSP” logo indicates those programs

that are created by the combination of Dolby Surround and

YAMAHA DSP technology.

Dolby Pro Logic + 2 Digital Sound Fields

Digital sound fields are created on the presence side and the

rear surround side of the Dolby Pro Logic Surround-decoded

sound field, respectively. They create a wide acoustic

environment and emphasize the surround effect in the room,

letting you feel as much presence as if you are watching a

movie in a popular Dolby Stereo theater.

This combination is available when the DOLBY PRO LOGIC

ENHANCED/DOLBY DIGITAL ENHANCED, 70 mm MOVIE

THEATER/DIGITAL MOVIE THEATER or TV SPORTS sound

field program is selected, and the input signal of source is

analog, PCM audio or encoded with Dolby Digital sound in

2-channel.

Dolby Digital + 3 Digital Sound Fields

Digital sound fields are created on the presence side and the

independent left and right surround sides of the Dolby Digital-

decoded sound field, respectively. They create a wide

acoustic environment and strong surround effect in the room

without losing high-channel separation. With the wide

dynamic range of Dolby Digital sound, this sound field

combination lets you feel as if you are watching a movie in the

newest Dolby Stereo Digital theater. This will be the most

ideal home theater sound at the present time.

This combination is available when the DOLBY PRO LOGIC

ENHANCED/DOLBY DIGITAL ENHANCED, 70 mm MOVIE

THEATER/DIGITAL MOVIE THEATER or TV SPORTS sound

field program is selected, and the input signal of source is

encoded with Dolby Digital sound (except in 2-channel).

05HTR-5140-e/f-1 6/22/99, 2:04 PM8

English

CONTROLS AND THEIR FUNCTIONS

FRONT PANEL

1 STANDBY/ON

Press this switch to turn on the power to this unit. Press it

again to set this unit to the standby mode.

Standby mode

In this state, this unit consumes a very small quantity of

power to receive infrared-signals from the remote control

transmitter.

2 Remote control sensor

This receives signals from the remote control transmitter.

3 Display

This shows various information. (Refer to page 11 for details.)

4 MEMORY (MAN’L/AUTO FM)

Press this button to store the broadcasting stations.

When this button is pressed and held for more than three

seconds, the automatic preset tuning begins.

5 EDIT

This button is used to exchange the assignment of two preset

stations with each other.

6 TUNING MODE (AUTO/MAN’L MONO)

Press this button to switch the tuning mode to automatic or

manual. To select the automatic tuning mode, press this button

so that the “AUTO TUNING” indicator lights up on the display.

To select the manual tuning mode, press this button so that the

“AUTO TUNING” indicator goes off.

7 FM/AM

Press this button to switch the reception band to FM or AM.

8 TUNING UP/DOWN

This button is used for tuning. Press the UP side to tune in to

higher frequencies, and press the DOWN side to tune in to

lower frequencies.

9 TAPE/MD MON / EXT. DECODER

Press this button to play a tape or an MD. The “TAPE/MD

MON” indicator lights up on the display.

When you press the button next, the “TAPE/MD MON” indicator

goes off, “EXT. DECDR” appears on the display and you can

play the signal connected to the EXTERNAL DECODER

INPUT terminals.

0 INPUT

Turn this selector to select the program source (VCR, VIDEO

AUX, TV/DBS, DVD/LD, CD, TUNER, PHONO) to listen to or

watch.

The name of the selected program source appears on the

display.

05HTR-5140-e/f-1 6/22/99, 2:04 PM9

q INPUT MODE

This button switches the DVD/LD and TV/DBS input signal

mode (AUTO/ANALOG).

w VOLUME

This control is used to raise or lower the volume level.

e PHONES jack

When you use headphones, connect the headphones to the

PHONES jack. You can listen to the sound to be output from

the main speakers through the headphones.

When using headphones only, set both SPEAKERS A and B to

the OFF position and switch off the digital sound field processor

(so that no DSP program name appears on the display) by

pressing EFFECT.

r SPEAKERS

Set A or B (or both A and B) to the ON position for the main

speaker system (connected to this unit) that you want to use.

Set the button(s) for the main speaker system you don’t want to

use to the OFF position.

t A/B/C/D/E

Press this button to select one of a group (A to E) of preset

stations.

y Preset station number selector

Each of these buttons selects a preset station number

(1 to 8).

u Tone controls

These controls are only effective for the sound from the main

speakers.

BASS

Use this control to increase or decrease the low-frequency

response. The “0” position produces flat response.

TREBLE

Use this control to increase or decrease the high-frequency

response. The “0” position produces flat response.

i BALANCE

This control is only effective for the sound from the main

speakers.

Turn the control to adjust the balance of the output volume to

the left and right speakers to compensate for sound imbalance

caused by the speaker location or listening room conditions.

o TIME/LEVEL

Press this button to select the item in the TIME/LEVEL mode.

p +/–

These buttons are used to adjust the settings of the SET MENU

mode and the TIME/LEVEL mode. In the TIME/LEVEL mode,

press + to increase the delay time or speaker output level.

Press – to decrease the delay time or speaker output level.

a SET MENU

Press this button to select functions in the SET MENU mode.

s PROGRAM selector

Press

or to select the DSP program.

The name of the selected program appears on the display.

d EFFECT

This button switches on and off the output from the center and

rear speakers so that the sound becomes the normal

2-channel.

* Even if the output from the center and rear speakers is off,

when the Dolby Digital is decoded, the signals on all

channels are distributed to the main channels and output

from the main speakers.

f VIDEO AUX terminals

Connect an auxiliary video or audio input source unit such as a

camcorder to these terminals. The source connected to these

terminals can be selected by INPUT.

05HTR-5140-e/f-1 6/22/99, 2:04 PM10

English

1 Multi-information display

This displays various information, for example the station

frequency, preset station number and name of the selected

program source.

2 MEMORY indicator

When MEMORY is pressed, this indicator flashes for about five

seconds. During this period, the displayed station can be

stored in the memory.

3 AUTO TUNING indicator

This lights up when the unit is in the automatic tuning mode.

4 TAPE/MD MON indicator

This lights up when the tape deck (or MD recorder, etc.) is

selected as the program source by pressing TAPE/MD MON /

EXT. DECODER on the front panel or TAPE/MD on the remote

control transmitter.

5 STEREO indicator

This lights up when an FM stereo broadcast with sufficient

signal strength is being received.

DISPLAY PANEL

Signal-level meter

This indicates the signal level of the station being received.

If multipath interference is detected, the indication decreases.

7 , and indicators

“

” lights up when the built-in Dolby Digital decoder is

on and the signal of the selected source encoded in Dolby

Digital sound is not in 2-channel. “

” lights up when the

built-in digital sound field processor is on, and “

”

lights up when the built-in Dolby Pro Logic Surround decoder is

on. Depending on the selected DSP program, both “

”

and “

”, or both “ ” and “ ” will light up.

8 SLEEP indicator

This lights up while the built-in SLEEP timer is functioning.

05HTR-5140-e/f-1 6/22/99, 2:04 PM11

REMOTE CONTROL TRANSMITTER

See “REMOTE CONTROL TRANSMITTER” on page 46 for full details.

1 Component selector

Press the button for the component you want to control with the

remote control transmitter. (The proper code must be set for

your component. See “SETUP CODES” on page 53.)

When the component selector has been pressed, the remote

control transmitter is set to operate that component.

2 POWER

When you have preset the code for a YAMAHA component, this

button switches between the power on and standby mode.

When you have preset the code for another manufacturer’s

component, this button turns on that component if it has a

remote control transmitter with a power button.

* It only functions when AMP<TUNER>, TAPE/MD, CD, DVD/LD or

DVD MENU on the component selector has been pressed.

3 TEST

Press this button to output the test tone for each speaker.

* It only functions when AMP<TUNER> on the component selector

has been pressed.

4 A/B/C/D/E, PRESET +/–

These buttons are used to select a preset station.

* They only function when AMP<TUNER> on the component selector

has been pressed.

5 MUTE

Press this button to mute the sound.

6 VOLUME

These buttons are used to adjust the volume.

: Turns up the volume.

: Turns down the volume.

7 SLEEP

This button is used to set the SLEEP timer.

8 PRG+, PRG–

These buttons are used to select a DSP program.

* They only function when AMP<TUNER> on the component selector

has been pressed.

9 Indicator

This flashes in red when a button on the remote control

transmitter is pressed. When it flashes rapidly several times,

press the selected button again.

0 Input selector (1 to 9)

/Numeric buttons

1) These buttons are used to select the program source to be

played.

* They only function when AMP<TUNER>, TAPE/MD, CD or

DVD/LD on the component selector has been pressed.

2) These buttons are used to select the menu or channel.

* They only function when DVD MENU, VCR, CBL/DBS or TV on

the component selector has been pressed.

05HTR-5140-e/f-1 6/22/99, 2:04 PM12

English

q EFFECT

/CLEAR

/+100

1) This button is used to switch the DSP program on or off.

* It only functions when AMP<TUNER>, TAPE/MD, CD, DVD/LD,

VCR or TV on the component selector has been pressed.

2) This button is used to clear the settings.

* It only functions when DVD MENU on the component selector

has been pressed.

3) This button is used to select the channel.

* It only functions when CBL/DBS on the component selector has

been pressed.

w ENTER

/+10

1) This button is used to enter the channel.

* It only functions when VCR, CBL/DBS or TV on the component

selector has been pressed.

2) This button is used to select the menu.

* It only functions when DVD MENU on the component selector

has been pressed.

e DISC SKIP +/–

/CH +/–

1) These buttons are used to skip to the next or previous disc.

* They only function when CD, DVD/LD or DVD MENU on the

component selector has been pressed.

2) These buttons are used to select the next or previous

channel.

* They only function when VCR, CBL/DBS or TV on the

component selector has been pressed.

r Operation buttons

/Setup buttons

1) These buttons function as play, stop, skip, etc. for

operating the component.

* They only function when TAPE/MD, CD, DVD/LD, VCR or TV on

the component selector has been pressed.

2) These buttons are for adjusting various settings.

* They only function when AMP<TUNER>, DVD MENU or CBL/

DBS on the component selector has been pressed.

05HTR-5140-e/f-1 6/22/99, 2:04 PM13

SPEAKER SETUP

This unit is designed to provide the best sound-field quality with

a 5-speaker configuration, using main speakers, rear speakers

and a center speaker.

The main speakers are used for the main source sound plus

the effect sounds. They will probably be the speakers from

your present stereo system. The rear speakers are used for

the effect and surround sounds, and the center speaker is for

the center sounds (dialog, vocals, etc.). If for some reason it is

not practical to use a center speaker, you can do without it.

Best results, however, are obtained with the full system.

The main speakers should be high-performance models and

have enough power-handling capacity to accept the maximum

output of your audio system.

The other speakers do not have to be equal to the main

speakers. For precise sound localization, however, it is ideal to

use high-performance models that can reproduce sounds over

the full-range for the center speaker and the rear speakers.

5-Speaker Configuration

This configuration is the most effective and recommended one.

When playing back a source using the DSP program,

DOLBY PRO LOGIC/DOLBY DIGITAL, DOLBY PRO LOGIC

ENHANCED/DOLBY DIGITAL ENHANCED, 70 mm MOVIE

THEATER/DIGITAL MOVIE THEATER, MONO MOVIE or TV

SPORTS, or when playing back a source which contains

center-channel signals (dialog, vocals, etc.) using any DSP

program that is Dolby Digital-decoded, conversations will be

output from the center speaker and the ambience will be

excellent.

Note: Set the CNTR (CENTER SPEAKER) mode to the

“LARGE” or “SMALL” position. (See page 23 for

details.)

SPEAKER CONFIGURATION

Use of a subwoofer expands your sound field

It is also possible to further expand your system with the

addition of a subwoofer and amplifier. The use of a subwoofer

is effective not only for reinforcing bass frequencies from any or

all channels, but also for reproducing the LFE (low frequency

effect) sound with high fidelity when playing back a source that

is Dolby Digital-decoded. You may wish to choose the

convenience of a YAMAHA Active Servo Processing Subwoofer

System, which has its own built-in power amplifier.

4-Speaker Configuration

The center speaker is not used in this configuration. When

playing back a source using the DSP program, DOLBY PRO

LOGIC/DOLBY DIGITAL, DOLBY PRO LOGIC ENHANCED/

DOLBY DIGITAL ENHANCED, 70 mm MOVIE THEATER/

DIGITAL MOVIE THEATER, MONO MOVIE or TV SPORTS, or

when playing back a source which contains center-channel

signals (dialog, vocals, etc.) using any DSP program that is

Dolby Digital-decoded, the center sound is output from the left

and the right main speakers. However, the sound effect of

other programs will be the same as that of the 5-speaker

configuration.

Note: Be sure to set the CNTR (CENTER SPEAKER) mode to

the “NONE” position. (See page 23 for details.)

SPEAKERS TO BE USED

Main L Main R

Rear L Rear R

Dialog

Surround sound

Main L Center Main R

Rear L Rear R

Dialog

Surround sound

05HTR-5140-e/f-2 6/22/99, 2:04 PM14

English

SPEAKER PLACEMENT

Refer to the following diagram when you place the speakers.

Main: The position of your present stereo speaker

system.

Rear: Behind your listening position, facing slightly

inward. Nearly 1.8 m (approx. 6 feet) up from the

floor.

Center: Precisely between the main speakers. (To avoid

interference with TV sets, use a magnetically

shielded speaker.)

Subwoofer: The position of the subwoofer is not as critical,

because low bass tones are not highly directional.

Rear

speaker (R)

Main

speaker (R)

Center speaker

Subwoofer

Main

speaker (L)

Rear

speaker

(L)

05HTR-5140-e/f-2 6/22/99, 2:04 PM15

SWITCHED AC OUTLET(S)

U.S.A., Canada, Singapore, China and General models

........................................................... 2 SWITCHED OUTLETS

Australia model .....................................1 SWITCHED OUTLET

Use these to connect the power cords from your components to

this unit.

The power to the SWITCHED AC OUTLET(S) is controlled by

this unit’s STANDBY/ON or the provided remote control

transmitter’s POWER. These outlets will supply power to any

component whenever this unit is turned on.

The maximum power (total power consumption of components)

that can be connected to the SWITCHED AC OUTLET(S) is

100 watts.

CONNECTIONS

Never plug in this unit and other components until all connections have been completed.

CONNECTIONS WITH OTHER COMPONENTS

When making connections between this unit and other components, be sure all connections are made correctly, that is to say L

(left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this unit.

* If you have YAMAHA components numbered as !, #, $, etc. on the rear panel, connections can be made easily by making sure

to connect the output (or input) terminals of each component to the same-numbered terminals of this unit.

Turntable Monitor TV

DVD player,

LD player, etc.

CD player Tape deck,

MD recorder, etc.

TV/DBS tuner

VCR

(Video cassette recorder)

To AC outlet

(U.S.A. model)

GND terminal (for turntable use)

Connecting the ground (earth) wire of the turntable to the GND terminal will normally minimize hum, but in some cases, better

results may be obtained with the ground wire disconnected.

05HTR-5140-e/f-2 6/22/99, 2:04 PM16

English

CONNECTING TO AN EXTERNAL DECODER

When using the DTS or other decoder with 6-channel discrete outputs, connect the 6CH DISCRETE OUTPUT terminals of the

decoder to the EXTERNAL DECODER INPUT terminals of this unit.

DTS or other decoder with 6-channel

discrete outputs

DVD player, LD player or other

unit with digital outputs

(U.S.A. model)

Camcorder

CONNECTING TO VIDEO AUX TERMINALS (ON THE FRONT PANEL)

These terminals are used to connect any video input source, such as a camcorder, to this unit.

VIDEO AUX

05HTR-5140-e/f-2 6/22/99, 2:04 PM17

CONNECTING TO DIGITAL (COAXIAL AND/OR OPTICAL) TERMINALS

If your DVD (LD) player, TV/DBS tuner, etc. are equipped with

coaxial or optical digital audio signal output terminals, they can

be connected to this unit’s COAXIAL and/or OPTICAL digital

signal input terminals.

To make a connection between optical digital audio signal

terminals, remove the cover from each terminal, and then

connect them by using a commercially available optical fiber

cable that conforms to EIAJ standards. Other cables might not

function correctly.

Even if you connect an audio/video unit to the COAXIAL (or

OPTICAL) terminal of this unit, you must keep the unit

connected with the same named analog audio signal terminals

of this unit, because a digital signal cannot be recorded by a

tape deck, MD recorder or VCR connected to this unit. You can

easily switch the selection of input signals between “digital” and

“analog”. (See page 30 for details.)

Notes

• When connecting an audio/video unit to both the digital and

analog terminals of this unit, make sure to connect between

terminals of the same name.

• Be sure to attach the covers when the OPTICAL terminals

are not being used in order to protect them from dust.

• The input signal from the DVD/LD input terminals is selected

in the following order of priority with the input mode set to the

AUTO position:

1 COAXIAL terminal

2 OPTICAL terminal

3 Analog terminal

• All digital audio signal input terminals are applicable to

sampling frequencies of 32 kHz, 44.1 kHz and 48 kHz.

• If your LD player has Dolby Digital RF signal output terminal

and not digital signal output, use the RF demodulator

(separate purchase).

DVD or LD player TV/DBS tuner

(U.S.A. model)

05HTR-5140-e/f-2 6/22/99, 2:04 PM18

English

Note

Use speakers with the specified impedance shown on the

rear panel of this unit.

Main speaker connections

One or two speaker systems can be connected to this unit. If

you use only one speaker system, connect it to either of the

SPEAKERS A or B terminals.

Rear speaker connections

A rear speaker system can be connected to this unit. Place

them to the rear of your listening position.

Center speaker connection

A center speaker can be connected to this unit. Place it on or

under the TV.

Subwoofer connection

You may wish to add a subwoofer to reinforce low frequencies

or to output low bass sound from the subwoofer channel.

If you have a subwoofer with built-in amplifier, including the

YAMAHA Active Servo Processing Subwoofer System, connect

the SUBWOOFER OUTPUT terminal of this unit to the input

terminal of the subwoofer system.

If you have a separate amplifier and subwoofer, connect the

SUBWOOFER OUTPUT terminal of this unit to the input

terminal of the subwoofer amplifier, and then connect the

speaker terminals of the subwoofer amplifier to the subwoofer.

When the input signals to this unit are for normal 2-channel

stereo, this terminal outputs only frequencies below 90 Hz from

the main and center channels. When discrete signals are input

to this unit and are selected as the input source, this terminal

outputs signals from the subwoofer channel.

Note: The output level of signals from this terminal is adjusted

by VOLUME on the front panel or VOLUME (

) on

the remote control transmitter.

CONNECTING SPEAKERS

Rear speakers

Subwoofer system

Center speaker

Right

Left

Main speakers A Main speakers B

Right

Left

Right Left

REAR

(SURROUND)

CENTER

MAIN

SUB

WOOFER

OUTPUT

SPEAKERS

05HTR-5140-e/f-2 6/22/99, 2:04 PM19

How to connect

Connect the SPEAKERS terminals to your speakers with wire of the proper gauge, cut as short as possible. If the connections are

faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct, that is the + and –

markings are observed. If these wires are reversed, the sound will be unnatural and lack bass.

Caution

Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could

damage the unit and/or speakers.

Connecting to the MAIN SPEAKERS terminals

Red: positive (+)

Black: negative (–)

1 Unscrew the knob.

2 Remove approx. 5 mm

(1/4”) of insulation from

each of the speaker

wires and insert the bare

wire into the terminal.

3 Tighten the knob to

secure the wire.

1 Press the tab.

2 Remove approx. 5 mm

(1/4”) of insulation from

each of the speaker

wires and insert the bare

wire into the terminal.

3 Release the tab to

secure the wire.

Connecting to the REAR and CENTER

SPEAKERS terminals

Red: positive (+)

Black: negative (–)

Banana plug connections are also possible (except for the

Singapore model). Simply insert the banana plug connector

into the corresponding terminal.

05HTR-5140-e/f-2 6/22/99, 2:04 PM20

La page charge ...

Yamaha HTR-5140 Manuel utilisateur

Marque: Yamaha

Modèle: HTR-5140

Catégorie: Destinataire

Taper: Manuel utilisateur

Ce manuel convient également à

RX-V495

Télécharger le PDF

rapport

dans d''autres langues

italiano: Yamaha HTR-5140 Manuale utente
English: Yamaha HTR-5140 User manual
español: Yamaha HTR-5140 Manual de usuario
Deutsch: Yamaha HTR-5140 Benutzerhandbuch
русский: Yamaha HTR-5140 Руководство пользователя
Nederlands: Yamaha HTR-5140 Handleiding
português: Yamaha HTR-5140 Manual do usuário
dansk: Yamaha HTR-5140 Brugermanual
polski: Yamaha HTR-5140 Instrukcja obsługi
čeština: Yamaha HTR-5140 Uživatelský manuál
svenska: Yamaha HTR-5140 Användarmanual
Türkçe: Yamaha HTR-5140 Kullanım kılavuzu
suomi: Yamaha HTR-5140 Ohjekirja
română: Yamaha HTR-5140 Manual de utilizare

Yamaha HTR-5140 Manuel utilisateur

Ce manuel convient également à

Yamaha HTR-5140 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents