Maximus VD01-05A1W-BK Manuel utilisateur

Maximus
Marque
Maximus
Modèle
VD01-05A1W-BK
Taper
Manuel utilisateur
DualCam
Video Doorbell
Top Camera
Bottom Camera
Microphone
Speaker
Button
LEDs
Instruction Manual
pg 01pg 08
Tools Needed (Not Included):
Power Drill
Pencil
(optional)
Level
(optional)
Step Stool
(optional)
Screwdriver Hammer
What’s in the Box
A
B
C
D
E
F
G
H
JI
K
L M
UP
1x
Answer
Doorbell
1x
Set Screw
(extra)
1x
Chime Bypass
2x
Short Screws
3x
Connector Wires
(1 extra)
1x
1/16” Allen Wrench
1x
1/4” Masonry Drill Bit
3x
Wall Screws &
Anchors
(1 extra)
3x
Wire Nuts
(1 extra)
1x
Backplate
1x
15-Degree
Wedge Bracket
1x
Backplate
Gasket
1x
Wedge Gasket
Industry Canada (IC) Compliance
This device complies with Industry Canada
licence-exempt RSS standard(s). Operation is subject
to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including
interference that may cause undesired operation of
the device.
Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux
conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le
fonctionnement.
This equipment complies with IC RSS-102 radiation
exposure limits set forth for an uncontrolled
environment. This eqipment should be installed and
operated with minimum distance 20cm between the
radiator and your body.
ce matériel est conforme aux limites de dose
d'exposition aux rayonnements, IC RSS-102 énoncée
dans un autre environnement.cette eqipment devrait
être installé et exploité avec distance minimale de 20
entre le radiateur et votre corps.
WARNING
Safety and Regulatory
Information
• Disconnect power at fuse or circuit
breaker before installing or servicing.
• Risk of fire or electric shock.
Installation requires knowledge of
electrical systems. If not qualified, do
not attempt to install. Contact a
qualified electrician.
• No user serviceable parts inside. To
avoid electric shock, do not
disassemble product.
• To prevent wiring damage or
abrasion, do not expose wiring to
edges of sheet metal or other sharp
objects.
Answer DualCam Video Doorbell
pg 07pg 02
Step 1:
Turn o the circuit breaker or fuse that your doorbell is
connected to, then verify that the power has been turned o by
pressing the doorbell button—you should not hear your doorbell
chime.
Note: If you have another chime bypass installed on your home’s
chime, replace it with the included Maximus Chime Bypass.
Step 2:
Locate the chime bypass included in your Answer Doorbell
installation kit.
Step 3:
Locate your home’s chime box and remove the cover.
Step 4:
Locate the “TRANS” and “FRONT” connections within your box.
(if installing at a front door)
Step 5:
Connect the chime bypass to the “TRANS” and “FRONT” connections.
(orientation and color does not matter)
Securely mount the chime bypass in place using the adhesive strip. It
may be secured inside or outside of chime box depending on your setup.
Step 6:
Replace the cover.
J
J
OFF
ON
ON
Chime Bypass Installation Guide
FCC Notice
Warning: Changes or modifications to this unit not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this
equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment o and on, the user is
For more information, check out our Help Center:
MaximusLighting.com/support
Phone: (855) 869-0304
Email: [email protected]
OR
help.getkuna.com
Phone: (855) 275-0412
Email: [email protected]om
Please recycle Answer DualCam
Video Doorbell’s packaging.
Need Help?
encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a circuit
dierent from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment. This equipment should be installed and
operated with minimum distance 20cm between the
radiator and your body. This transmitter must not be
co-located or operating in conjunction with any
other antenna or transmitter.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and
(2) this device must accept any interference
received, including interference that may cause
undesired operation.
FRONT
TRANS
REAR
pg 03pg 06
Step 8:
Download free Kuna App from Apple App
Store or Google Play Store. Follow in-app
instructions to set up your doorbell.
Step 1 (Optional):
If you would like to use a wedge to change the viewing
angle, follow Step 2 and Step 3 using the wedge and
wedge gasket instead of the backplate and backplate
gasket. After installing the wedge, use the short screws
to attach the backplate to the wedge.
Note: the wedge can be flipped to angle your camera to
the left or right. Make sure you install the wedge in the
orientation that works best for you.
Note: You should have disconnected the power for your
doorbell circuit when you installed the chime bypass.
Please ensure that the power is still o before beginning
the doorbell installation.
Step 2:
Hold the backplate up against your wall such that
the existing wires go through the large hole and
mark the mounting screw areas.
a. For stucco, brick, or concrete: drill pilot holes
using the supplied drill bit and then push/hammer
in plastic anchors for screws.
b. For wood or siding: install screws directly (do
NOT use the supplied drill bit - it is meant for the
anchors). We highly recommend drilling a pilot
hole before installing the screws if not using the
anchors.
G
Doorbell Installation Guide
Step 6:
Feed the wires and wire nuts back into the
wall and then mount the doorbell by sliding
the bottom of the doorbell onto the backplate
and pushing the top into place. Note: a little
upward pressure may be required to attach
the doorbell to the backplate.
Use the provided Allen wrench to tighten the
preinstalled set screw to secure the doorbell
in place through the top screw hole.
Step 7:
Restore power to your Answer Doorbell circuit.
Step 4:
Use the provided wire nuts to
attach the connector wires to your
existing doorbell wiring. Wire color
is interchangeable - it does not
matter which way they are
connected.
Step 5:
Loosen the screws on the back of
your doorbell. Connect the
connector wire spades (or your
existing wires) to the screws on
your Answer Doorbell. It doesn’t
matter which wire you connect to
which screw - just make sure the
wires aren’t touching one another
and are securely connected.
B
H
K
UP
A
B
L
B
A
RESET
USB
UP
Pencil
B
UP
Step 3:
Attach the provided backplate
gasket to the backplate.
Install the backplate with the 2 wall
screws to the location as shown.
Note:
be sure that the backplate is
facing the correct direction with
the “Up” label visible and arrow
pointing up.
B DG
UP
UP
GI B C E
pg 05pg 04
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Maximus VD01-05A1W-BK Manuel utilisateur

Maximus
Marque
Maximus
Modèle
VD01-05A1W-BK
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents