IKEA IUD9500WX0 Guide d'installation

Marque: IKEA

Modèle: IUD9500WX0

Taper: Guide d'installation

Ce manuel convient également à

I KEA ®

INSTALLATIONINSTRUCTIONS

UNDERCOUNTERDISHWASHER

PLASTICGIANT TUBMODELS

INSTRUCTIONSD'INSTALLATION

LAVE-VAISSELLEENCASTRE

MODELESA TRESGRANDE CUVE EN PLASTIQUE

TABLEOF CONTENTS

DISHWASHER SAFETY ............................................................... 2

INSTALLATION REQUIREMENTS .............................................. 3

Tools and Parts .......................................................................... 3

Location Requirements .............................................................. 3

Drain Requirements ................................................................... 4

Water Supply Requirements ...................................................... 5

Electrical Requirements ............................................................. 5

INSTALLATION INSTRUCTIONS ................................................ 5

Prepare Cabinet Opening .......................................................... 5

Prepare Cabinet Opening Where There Are No

Existing Utility Hookups ............................................................. 8

Install Moisture Barrier ............................................................ 11

Prepare Dishwasher ................................................................ 11

Install the Door Handle ............................................................ 13

Custom Panel Dimensions ...................................................... 13

Install Custom Panel ............................................................... 13

Choose Attachment Option .................................................... 14

Move Dishwasher to Final Location ........................................ 16

Level the Dishwasher .............................................................. 16

Make Electrical Connection .................................................... 17

Connect to Water Supply ........................................................ 18

Connect to Drain ..................................................................... 18

Secure Dishwasher in Cabinet Opening ................................. 19

Complete Installation .............................................................. 19

TABLEDESMATIERES

SI_CURITI_ DU LAVE-VAISSELLE ............................................ 21

EXIGENCES D'INSTALLATION ................................................ 22

Outils et pieces ........................................................................ 22

Exigences d'emplacement ...................................................... 22

Exigences concernant I'evacuation ........................................ 23

Specifications de I'alimentation en eau .................................. 24

Specifications electriques ....................................................... 24

INSTRUCTIONS D'INSTALLATION .......................................... 24

Amenagement de la cavite d'encastrement du placard ......... 24

Preparation de I'espace d'encastrement

du placard non dote de moyens de raccordement ................ 27

Installation de la barriere anti-humidite ................................... 31

Preparation du lave-vaisselle .................................................. 31

Installation de la poignee de porte .......................................... 33

Dimensions du panneau personnalise .................................... 33

Installation de panneau personnalise ..................................... 34

Choose I'option d'attachement ............................................... 35

Deplacer le lave-vaisselle jusqu'& son emplacement final ..... 36

12tablissement de I'aplomb du lave-vaisselle .......................... 37

Raccordement electrique ........................................................ 37

Raccordement & la canalisation d'eau .................................... 39

Raccordement a I'evacuation ................................................. 39

Fixation du lave-vaisselle dans I'espace d'encastrement ...... 40

Achever I'installation ............................................................... 41

W10254955A

DISHWASHERSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured ifyou don'tfollow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

You need to:

• Slowly open dishwasher drawer while someone grasps the

rear of the dishwasher. Remove shipping materials. Close

dishwasher drawer. Latch the dishwasher drawer shut.

• Observe all governing codes and ordinances.

• Install this dishwasher as specified in these instructions.

• Have everything you need to properly install dishwasher.

• Contact a qualified installer to ensure that dishwasher is

installed to meet all electrical and plumbing national and local

codes and ordinances.

INSTALLATIONREQUIREMENTS

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

• Pliers

• Phillips screwdriver

• Flat-blade screwdriver

• _e" and 1¼,,nut drivers or

hex sockets

• Measuring tape or ruler

• 11/2"hole saw bit

• Twist-on wire connectors

[proper size to connect

household wiring to 16-

gauge wiring in

dishwasher] (2)

• 15 TORX®tscrewdriver

(if installing custom front

panels)

• 10" adjustable wrench

(opens to 11/8"[2.9 cm])

• Utility knife

• Level

• Cordless drill

• 8/8"open-end wrench

• Flashlight

• Shallow pan

• Wood block

• Bath towel

Parts needed

• 90° elbow with 3/8"N.RT.

external threads on one

end. (The other end must

fit your water supply line.)

• Teflon ®ttape or pipe joint

compound

Shims

#10 x 1/2"wood screws

[if installing custom front

panels] (4)

Tools needed (new installation)

• Cordless drill •

• 1/2",3/4"and 11/2"hole saw •

bits •

Small tubing center

Wire stripper

1V2"to 2" screw-type

clamp (if connecting to

waste-tee)

Parts needed (new installation)

• Copper tubing (3/8" •

recommended) or

• Flexible stainless steel

braided fill line

Clamp connector or

conduit connector

(to fit a 7/8"[2.2 cm]

diameter hole)

Parts supplied

A. Drain hose clamps [1 large and 1 small] (2)

B. #10 x 1/2"Phillips-head screws (2)

C. Drain hose

_TORX is a registered trademark of Acument Intellectual Properties, LLC

<_Teflon is a registered trademark of E.I. Dupont de Nemours and Company.

Additional parts supplied (top-venting models only)

• Bottom sound pad (located in lower rack)

• Moisture barrier tape

Make sure all these parts are included. If not, call

1-866-664-2449.

See separate parts list for accessories available for your

dishwasher.

ocoo ec J smen s

Do not run drain lines, water lines or electrical wiring where they

can interfere with or contact the dishwasher motor or legs.

The location where the dishwasher will be installed must provide

clearance between motor and flooring. Motor should not touch

the floor.

Do not install dishwasher over carpeted flooring.

Shelter dishwasher and water lines leading to dishwasher against

freezing. Damage from freezing is not covered by the warranty.

A side panel kit is available from your dealer for installing your

dishwasher at the end of your cabinetry.

A moisture barrier accessory (Part Number 4396277) is available

from your dealer for installing underneath the countertop, but is

not required. Call 1-866-664-2449 for ordering.

Check location where the dishwasher will be installed. The

location must provide:

• Easy access to water, electricity and drain.

• Convenient access for loading and unloading dishes. Corner

locations require a 2" (5.1 cm) minimum clearance between

the side of the dishwasher door and the wall or cabinet.

• Square opening for proper orientation.

• Cabinet front perpendicular to floor.

• Level floor. Ifthe floor at the front of the dishwasher is not level

with the rear of the opening, shims may be needed to level the

dishwasher.

NOTE: To avoid shifting during dishwasher operation, shims

must be securely attached to the floor.

If the dishwasher will be left unused for a period of time or it is in a

location where it may be subject to freezing, have it winterized by

authorized service personnel.

Make sure pipes, wires and drain hose are within the shaded area

shown in the "Cutout dimensions" section.

Helpful Tip: Ifthe floor in the dishwasher opening is uneven

(example: tile flooring only partway into opening), accurately

measure the dimensions and level the dishwasher.

Product Dimensions

Side View

I_---- 21 " (53.3 cm) -_

A. _" (1.9 cm) insulation by be compressed

(not used on all models)

B. 33 _" (86 cm) minimum with wheels

removed

Rear View

237/8 '' (60.6 cm)

Installation Clearances

Cutout dimensions

(5.1 cm)

(25.4 cm

24"

(61 cm)*

34"

(86.4 cm)*

(5.1 cm) l

6" (15.2 cm)***

(8.3 cm) (7 cm) _ --

Cut holes in shaded area of cabinet walls or floor as specified below:

Water line - ½" (1.3 cm)

Drain line - 1½" (3.8 cm)

Direct wire - _" (1.9 cm)

Power supply cord - 1½" (3.8 cm)

*Measured from the lowest point on the underside of the

countertop. May be reduced to 337/8'' (86 cm) by removing the

wheels from the dishwasher.

**Minimum, measured from narrowest point of opening.

***May be increased to 68/8'' (16.6 cm) if height of opening is 341/2''

(87.6 cm) at its lowest point.

Use the new drain hose supplied with your dishwasher. If this

is not long enough, use a new drain hose with maximum

length of 12 ft (3.7 m) that meets all current AHAM/IAPMO test

standards, is resistant to heat and detergent, and fits the

1" (2.5 cm) drain connector of the dishwasher.

Connect drain hose to waste tee or disposer inlet above drain

trap in house plumbing and 20" (50.8 cm) minimum above the

floor. It is recommended that the drain hose either be looped

up and securely fastened to the underside of the counter, or

be connected to an air gap.

Use a drain air gap if the drain hose is connected to house

plumbing lower than 20" (50.8 cm) above the subfloor or floor.

Use 1/2"(1.3 cm) minimum I.D. drain line fittings.

odp©/y

• A hot water line with 20-120 psi (138-862 kPa) water pressure.

• 120°F (49°C) water temperature at dishwasher.

• Flexible stainless steel braided fill line (1/2" minimum plastic

tubing is not recommended).

Contact a qualified electrician.

Ensure that the electrical installation is adequate and in

conformance with all national and local codes and ordinances.

You must have:

• 120-volt, 60 Hz, AC-only, 15 or 20 amp fused electrical supply.

• Copper wire only.

We recommend:

• A time-delay fuse or circuit breaker.

• A separate circuit.

If direct wiring dishwasher:

• Use flexible, armored or nonmetallic sheathed, copper wire

with grounding wire that meets the wiring requirements for

your home and local codes and ordinances.

Use strain relief method provided with house wiring junction

box or install a UL-listed/CSA-certified clamp connector to the

house wiring junction box. If using conduit, use a

UL-listed/CSA-certified conduit connector.

If connecting dishwasher with a power supply cord:

• Use Power Supply Cord Kit (Part Number 4317824) marked

for use with dishwashers. Kit contents include:

• Voltex, Inc., UL listed 16 gauge 3 wire power supply cord

with 3 prong grounded plug.

• Neer C-500 _/2'strain relief.

• 3 wire connectors.

• Part Number 302797 grommet.

Follow the kit instructions for installing the power supply cord.

Power supply cord must plug into a mating three prong,

grounded outlet, located in the cabinet next to the dishwasher

opening. Outlet must meet all local codes and ordinances.

INSTALLATIONINSTRUCTIONS

Electrical Shock Hazard

Disconnect electrical power at the fuse box or circuit

breaker box before installing dishwasher.

Failure to do so can result in death or electrical shock.

1. Disconnect power.

2. Turn off water supply.

/,,Jst_9 ®xsn 9 u ty hookups

Follow the steps in the section if you are installing the

dishwasher in an existing cabinet opening with utility

hookups.

If you are installing the dishwasher in a cabinet opening that

does not have utility hookups, follow the steps under "Prepare

cabinet opening where there are no existing utility hookups"

section.

1. Check that the water line reaches to the front left of the

opening where the water connection will be made.

A. Water line

B. Direct wire

2. Check that the direct wire reaches to the front right of opening

where the electrical connection will be made.

If the water line and direct line wire reach far enough into the

opening, proceed to the next section, "Install the Drain Hose." If

they do not reach far enough, follow the steps under "Prepare the

Cabinet Opening Where There are no Existing Utility Hookups."

Install the Drain Hose

IMPORTANT: Always use a new drain hose even when installing a

new replacement dishwasher.

1. Drill a 1V2"(3.8 cm) diameter hole inthe cabinet wall or floor on

the side of the opening closest to the sink.

i/ i

Connect drain hose to waste tee or waste disposer using one

of the following methods:

• Option 1, Waste disposer- with air gap

• Option 2, No waste disposer- with air gap

• Option 3, Waste disposer- no air gap*

• Option 4, No waste disposer- no air gap*

*An air gap is recommended.

Helpful Tip" To reduce the vibration of the hose, keep the

hose away from the floor and the edge of the hole where it

passes through the cabinet.

Option 1: Waste Disposer - with air gap

1. Remove the disposer knockout plug. Cut end of drain hose if

needed (do not cut ribbed section).

A.Drain hose cut here if needed)

2. Attach drain hose to air gap with large spring-type clamp. If

the drain hose was cut, use a 1W' to 2" (3.8 to 5 cm) screw-

type clamp**.

3. Use a rubber hose connector** with spring or screw-type

clamps to connect air gap to disposer inlet.

This connection must be before the drain trap and at least 20"

(50.8 cm) above the floor where dishwasher will be installed.

A H

A. Spring or screw-type clamps

B.Disposer inlet

C. Drain trap

D. Rubber hose connector

E.Drain hose

F. Drain hose (cut here if needed)

G. Large spring clamp

H. Air gap

4. Insert drain hose through the front center of opening where

drain connection will be made.

A. Drain hose

**Parts available from local plumbing supply stores.

Option 2: No Waste Disposer - with air gap

1. Cut end of drain hose if needed (do not cut ribbed section).

A. Drain hose (cut here if needed)

2. Attach drain hose to air gap with large spring-type clamp. If

the drain hose was cut, use a 1W' to 2" (3.8 to 5 cm) screw-

type clamp**.

3. Use a rubber hose connector** with spring or screwtype

clamps to connect air gap to waste tee.

This connection must be before the drain trap and at least 20"

(50.8 cm) above the floor where dishwasher will be installed.

A. Spring or screw-type clamps

B. Waste tee

C. Drain trap

D. Rubber hose connector

E.Large spring clamp

F. Drain hose (cut here)

G. Air gap

4. Insert drain hose through hole cut in cabinet to the front center

of opening where drain connection will be made.

A. Drain hose

**Parts available from local plumbing supply stores.

Option 3: Waste Disposer - no air gap

1. Remove the disposer knockout plug. Do not cut end of drain

hose.

Attach drain hose to disposer inlet with large springtype

clamp.

This connection must be before the drain trap and at least 20"

(50.8 cm) above the floor where dishwasher will be installed. It

is recommended that the drain hose be looped up and

securely fastened to the underside of the counter.

A. Large spring-type C. Disposer inlet

clamp D. Drain trap

B. Drain hose

Insert drain hose through hole cut in cabinet to the front center

of opening where drain connection will be made.

A. Drain hose

Option 4: No Waste Disposer - no air gap

1. Cut end of drain hose if needed (do not cut ribbed section).

I I

A. Drain hose but here if needed)

Attach drain hose to waste tee with 11/2"to 2" (3.8 to 5 cm)

screw-type clamp**.

This connection must be before the drain trap and at least 20"

(50.8 cm) above the floor where dishwasher will be installed. It

is recommended that the drain hose be looped up and

securely fastened to the underside of the counter.

A. Waste tee D. Drain hose

B. Drain trap E.Drain hose (cut

C. Screw-type clamp here if needed)

Insert drain hose through hole cut in cabinet to the front center

of opening where drain connection will be made.

A.Drain hose

**Parts available from local plumbing supply stores.

Electrical Connection

Option 1: Direct Wire Method

Helpful Tip: Wiring the dishwasher will be easier if you route wire

into the cabinet opening from the right-hand side.

1. Drill a 3/4"(1.9 cm) hole in right-hand cabinet side, rear or floor.

Preferred and optional locations are shown.

A B

A. Optional locations

B. Preferred locations

Wood cabinet: Sand hole until smooth.

Metal cabinet: Cover hole with grommet, not provided.

3. Run wire into house wiring junction box.

4. Install a UL-listed/CSA-certified clamp connector (strain relief)

for flexible-type wire. If installing conduit, attach a UL-listed/

CSA-certified conduit connector to the junction box.

5. Run other end of wire through cabinet hole. Cable must

extend to the right front of cabinet opening.

A. Direct wire

Option 2: Power Supply Cord Method

NOTE: A mating, three-prong, grounded-type wall receptacle is

required in a cabinet next to the dishwasher opening.

1. Drill a 1V2"(3.8 cm) hole in the cabinet rear or side. Preferred

and optional locations are shown.

A B

A. Optional locations

B. Preferred locations

Wood cabinet: Sand hole until smooth.

Metal cabinet: Cover hole with grommet

(Part Number 302797) included with power supply cord kit.

Install the Water Line

Helpful Tip: Routing the water line through the left side of cabinet

opening will make water connection easier.

1. Drill a minimum 1/2"(1.3 cm) hole in the cabinet side, rear or

floor. Preferred and optional locations are shown.

A B

A. Optional locations

B. Preferred locations

2. Measure overall length of copper tubing required.

3. Attach copper tubing to the water line with a manual shutoff

valve.

A. Copper tubing

Slowly feed copper tubing through hole in cabinet. Copper

tubing will bend and kink easily, so be gentle. The copper

tubing should be far enough into the cabinet opening to

connect it to dishwasher inlet on the front left of the

dishwasher.

5. Turn water shutoff valve to "ON" position. Flush water into a

shallow pan to get rid of particles that may clog the inlet valve.

6. Turn shutoff valve to "OFF" position.

Install the Drain Hose

IMPORTANT: Always use a new drain hose even when installing a

new replacement dishwasher.

1. Drill a 11/2"(3.8 cm) diameter hole in the cabinet wall or floor on

the side of the opening closest to the sink.

Connect drain hose to waste tee or waste disposer using one

of the following methods:

• Option 1, Waste disposer- with air gap

• Option 2, No waste disposer- with air gap

• Option 3, Waste disposer- no air gap*

• Option 4, No waste disposer- no air gap*

*An air gap is recommended.

Helpful Tip: To reduce the vibration of the hose, keep the hose

away from the floor and the edge of the hole where it passes

through the cabinet.

Option 1: Waste Disposer - with air gap

1. Remove the disposer knockout plug. Cut end of drain hose if

needed (do not cut ribbed section).

A.Drain hose cut here if needed)

Attach drain hose to air gap with large spring-type clamp. If

the drain hose was cut, use a 1V2"to 2" (3.8 to 5 cm) screw-

type clamp**.

Use a rubber hose connector** with spring or screw-type

clamps to connect air gap to disposer inlet.

NOTE: This connection must be before the drain trap and at

least 20" (50.8 cm) above the floor where dishwasher will be

installed.

A H

A. Spring or screw-type clamps

B. Disposer inlet

C. Drain trap

D. Rubber hose connector

E.Drain hose

F. Drain hose (cut here if needed)

G. Large spring clamp

H. Air gap

4. Insert drain hose through the front center of opening where

drain connection will be made.

A. Drain hose

**Parts available from local plumbing supply stores.

Option 2: No Waste Disposer - with air gap

1. Cut end of drain hose if needed (do not cut ribbed section).

A. Drain hose (cut here if needed)

2. Attach drain hose to air gap with large spring-type clamp. If

the drain hose was cut, use a 1V2"to 2" (3.8 to 5 cm) screw-

type clamp**.

3. Use a rubber hose connector** with spring or screwtype

clamps to connect air gap to waste tee.

This connection must be before the drain trap and at least 20"

(50.8 cm) above the floor where dishwasher will be installed.

A. Spring or screw-type clamps

B. Waste tee

C. Drain trap

D. Rubber hose connector

E.Large spring clamp

F. Drain hose (cut here)

G. Air gap

4. Insert drain hose through hole cut in cabinet to the front center

of opening where drain connection will be made.

A. Drain hose

**Parts available from local plumbing supply stores.

Option 3: Waste Disposer - no air gap

1. Remove the disposer knockout plug. Do not cut end of drain

hose.

Attach drain hose to disposer inlet with large springtype

clamp.

NOTE: This connection must be before the drain trap and at

least 20" (50.8 cm) above the floor where dishwasher will be

installed. It is recommended that the drain hose be looped up

and securely fastened to the underside of the counter.

C ................................B

A. Large spring-type clamp C. Disposer inlet

B. Drain hose D. Drain trap

3. Insert drain hose through hole cut in cabinet to the front center

of opening where drain connection will be made.

A. Drain hose

Option 4: No Waste Disposer - no air gap

1. Cut end of drain hose if needed (do not cut ribbed section).

I I

A. Drain hose but here if needed)

Attach drain hose to waste tee with 11/2"to 2" (3.8 to 5 cm)

screw-type clamp**.

This connection must be before the drain trap and at least 20"

(50.8 cm) above the floor where dishwasher will be installed. It

is recommended that the drain hose be looped up and

securely fastened to the underside of the counter.

A. Waste tee D. Drain hose

B. Drain trap E.Drain hose (cut here

C. Screw-type clamp if needed)

Insert drain hose through hole cut in cabinet to the front center

of opening where drain connection will be made.

A. Drain hose

**Parts available from local plumbing supply stores.

'_._ ' s_. _ _ _ ,, _ _

(on some modes}

Make sure the area under the cabinet is clean and dry for

installation of the moisture barrier.

Remove the backing of the moisture barrier and apply to

underside of the countertop along the front edge of the

counter.

--¢/ \__

A. Moisture barrier

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

Put corner posts from packaging behind dishwasher. Grasp

sides of dishwasher door frame and put dishwasher on its

back, resting on top of the corner posts.

Remove two screws attaching access panel and lower panel

to dishwasher using a V4"hex socket, nut driver or Phillips

screwdriver.

A. Access panel

B. Lower panel

C. Grounding clip

3. Remove panels and set panels aside on a covered surface.

4. Check that grounding clip is attached to the lower panel.

5. Apply Teflon®tape or pipe joint compound to 90° elbow fitting

and connect fitting to water inlet valve.

6. Tighten elbow until snug, and be sure that it faces to the rear.

A. Water inlet valve

B. Elbow

7. Remove terminal box cover.

• If you are direct wiring: install a UL-listed/CSA certified

clamp connector to the terminal box. If using conduit, use

a UL-listed/CSA-certified conduit connector.

If you are installing a power supply cord kit, do so now,

following kit instructions.

A. Dishwasher wires

B. Terminal box cover

C. Cable clamp connector

Helpful Tip: Put cardboard under dishwasher until it is

installed in cabinet opening. The cardboard will help

shield the floor covering during installation.

Measure height of cabinet opening

from underside of countertop to floor

where dishwasher will be installed

(you need the lowest point).

Check chart for that height opening.

Put wheels in the required position.

Minimum Wheel Number

cutout Position of turns

height on

front leg

34" A 10

(86.4 cm)

341/4" B 5

(87 cm)

341/2'' C 0

(87.6 cm)

D Wheel

Turn both front leveler legs to the same height.

A. Front leg

If the minimum cutout height is less than 34" (86.4 cm), the

rear wheels can be removed for additional clearance. This will

allow the dishwasher to fit into a337/8'' (86 cm) high cutout, but

the dishwasher will be more difficult to move into position. If

the wheels are removed, avoid damage to the floor when

moving the dishwasher.

If you have built-up floors

Measure height of opening from underside of countertop to

built-up floor. If the height is at least 333/4'' (85.7 cm), the

dishwasher will fit into the opening without modification to the

countertop or flooring.

33-343/4"

(85.7cm)

A. Countertop

B. Shim

C. Built-up floor

Put wheels in position 1 and turn the front leveler legs up all

the way.

Add shims as needed in the area shown to bring dishwasher

up to the proper height.

NOTE: Make sure shims are securely attached to floor so the

dishwasher does not move when operated.

3/4" 6"

(7 crn)(15.2 cm) (7 crn)

A. Shims

IMPORTANT: Do not scratch the front panel during this

procedure.

1. Remove the door handle and hardware bag containing the

setscrews and Allen wrench from the cardboard box.

2. Start setscrews in handle.

3. Place handle on mounting studs with the setscrews facing

down.

Push the door handle tightly against the door. Insert the short

end of the Allen wrench into the setscrews. Tighten the

setscrews 1/4turn past snug. Retain Allen wrench with

Installation Instructions.

A. Mounting stud

B.Door handle

C. Setscrew (inside of door handle standoff)

D. Allen wrench

IMPORTANT: You need to know what control panel is on your

dishwasher before you order your custom door panel.

For dishwashers with the control panel shown below:

(Model IUD9500W)

/" Cycles Options

@_w @No_m_@ C_I_U_U@_ @....H4g_ @_t_ _at_D_y @4H°_D_I_y@'_@_dLoo_@_ _,_o,@TAmaA_C_L@

(Your model may vary sightly from the picture above.)

Custom door panel dimensions

(59.7crn)

30 3/16"

*This dimension is for 4" (10.2 cm) toe kick. If the installation

needs a higher toe kick, adjust the height of the wood panel

accordingly. Not recommended for toe kicks greater than 6"

(15.2 cm).

..... ,,.,.,_,_;::_0__ _ _,_.............

For model IUD9500W

NOTE: The handle for the custom panel is not included.

IMPORTANT: If the handle is attached from the back of the

custom panel, the screw holes should be countersunk for the

screws heads to be flush with the panel. If the handle is attached

to the front of the custom panel, the screw lengths cannot exceed

the panel thickness.

NOTES:

A customer-supplied full front panel must weigh no more than

16 pounds (7.3 kg) and must be made to specific dimensions.

It is recommended that a cabinetmaker cut the custom panel

because of the precise dimensions needed.

All mounting hardware supplied is for a 3/4"(19.1 mm) thick

wood panel. If a thinner wood panel, or materials other than

wood are used, it is the consumer's responsibility to obtain the

proper length screws and adjust the pilot holes accordingly.

IMPORTANT: Use a moisture resistant sealer on both sides and

all edges of the panel to avoid damage from humidity.

1. With aTORX@screwdriver, remove three screws from both

sides, as shown; hold the outer panel up while removing the

screws. Save screws for reinstallation.

*This dimension is for 4" (10.2 cm) toe kick. If the installation

needs a higher toe kick, adjust the height of the wood panel

accordingly. Not recommended for toe kicks greater than 6"

(15.2 cm).

-.j

A.Screws

B.Outer panel

2. Gently set outer panel aside.

3. Lay the customer-supplied custom panel face down on a

covered, non-scratching surface.

4. Measure 92%2" (25.2 cm) from top edge and mark a line on the

back of customer-supplied custom panel.

9 29/32"

(25.2crn)

A. Mark line

B. Top edge

Position the outer panel on the back of the customer supplied

custom panel as shown, so that the top holes in the outer

panel are on the line, and both panels are centered side to

side.

Mark all four hole locations; remove outer panel. Drill 3/32"pilot

holes 1/2"(13 mm) deep in customer-supplied custom panel.

A. Mark pilot holes

Place the outer panel on the back of the customer-supplied

custom panel. Align holes.

Attach outer panel to back of customer-supplied

custom panel with the four #10-16 x 3/8"hex head

screws supplied in the package containing

literature.

9. Attach the handle. The handle should be centered on the front

of the customer-supplied custom panel in the area shown.

A. Handle location

10. Attach the panel assembly to the door by reinstalling the three

screws on each side; do not tighten completely. This will hold

the panel assembly in place on the door frame.

11. Align the top edge of the customer-supplied custom panel

with the top of the console.

12. Drill two 3/32"pilot holes 1/2"(13 mm) deep, into the customer-

supplied custom panel, through the holes in the top corners of

the inner panel as shown.

A. Inner panel

B. Align top edges

C. Drill through these holes

13. Install the two #8-1 8x 13/8"screws from the literature package

in the top corners of the inner panel.

14. Tighten the six side screws reinstalled in Step 10.

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

Using two or more people stand the dishwasher up.

Option 1: Countertop

The dishwasher must be secured to the cabinet. There are two

brackets on top of the dishwasher that can be attached to the

countertop if it is wood, laminate or other similar surfaces. Ifyour

countertop is marble, granite or other hard surface the brackets

may be moved to the sides of the dishwasher.

NOTE: Do not attach the dishwasher. This will be done later.

A.Brackets

Option 2: Dishwasher Side Attachment

(for marble, granite or other hard surface countertops)

1. To remove the brackets from the top, flatten tab at back of

brackets with pliers, and pull the brackets out of the slots.

A. Tabs

Break off the end of the bracket along the scored line.

A. Score line

With another person holding the rear of the dishwasher to

keep it from tipping, open dishwasher door and place towel

over pump assembly and spray arm of dishwasher. This will

keep screws from falling into pump area when securing

dishwasher to cabinet.

4. Push the plastic buttons out of the side of the tub.

NOTE: Save the buttons to cover the holes after dishwasher is

installed.

A. Plastic button

Push bracket into slot on the side of dishwasher, and bend tab

in towards the side of the dishwasher so that it keeps the

bracket in place. Repeat this step for the other side of the

dishwasher.

NOTE: Do not attach the dishwasher. This will be done later.

A. Bend tabs

Check Door Spring Tension

1. With another person holding the rear of the dishwasher to

keep it from tipping, open and close the door a few times. If

the door closes or falls open under its own weight, the door

tension will need to be adjusted.

2. To adjust the door spring tension, unhook the spring from the

rear leg of dishwasher.

3. With a5/le"nut driver or hex socket, remove the screw from

the tensioner.

The screw can be put into one of three holes C, D or E, in the

front leg of dishwasher. If the door closes by itself, move the

tensioner to a higher number hole and replace screw. When

door is unlatched, if it opens by itself, move tensioner to a

lower numbered hole and replace screw.

Reattach door spring to rear leg. Tensioners on both sides of

dishwasher should be secured at same holes.

A. Spring

CDE

A. Screw

B. Tensioner

C. First hole location (lower setting)

D. Second hole location (medium setting)

E. Third hole location (higher setting)

MOV@ '_'_............ - Ic ' .........,,,s_,,,,_,,

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

1. Grasp the sides of the dishwasher at the edges of the door

panel.

2. Tilt dishwasher backwards on wheels and move dishwasher

close to cabinet opening. Do not push on the front of the

panel or on the console--they may dent.

3. If dishwasher has a power supply cord, insert power supply

cord into hole cut into cabinet. If using direct wire, check that

it is on the right front side of opening.

Check that water line is on the left side of opening and drain

hose is near the center of the hole in the cabinet.

Slowly move dishwasher

completely into cabinet

opening. Do not kink or pinch

copper tubing, drain hose,

power supply cord or direct

wire between dishwasher and

cabinet.

Helpful Tip: Once the

dishwasher is in position, you

may have to support the front

of the dishwasher by raising,

lowering or shimming front feet.

6. Remove cardboard from under dishwasher.

NOTE: It is all right if dishwasher fits tightly into cabinet

opening. Do not remove insulation blanket --the blanket

reduces the sound level.

IN®[}ishwcssBe[

Align front of dishwasher door panel with cabinet doors. You

may need to adjust alignment to be even with your cabinets.

Helpful Tip: Prop up one side of frame to hold dishwasher up

off floor when adjusting front legs.

2. Check that leveling legs are firmly against the floor.

Close and latch the door, and place level against the front

panel. Check that dishwasher is plumb. If needed, adjust

leveling leg or add shims under rear wheel until dishwasher is

plumb.

Repeat for other side of the dishwasher.

NOTE: Make sure the shims are securely attached to the floor.

This will hold the shims in place when dishwasher is being

operated.

Place level against top front opening of tub. Check that

dishwasher is level from side to side. If dishwasher is not level,

adjust front legs up or down until dishwasher is level.

_ _ _i,_*_,,_ _ 2_¸ _ _ _ _

Check "Electrical Requirements" section.

You need to:

• have the correct electrical supply and recommended

grounding method.

If you are"

• direct wiring use Option 1.

• using a power supply cord, use Option 2.

Option 1: Direct Wiring

1. Route direct wire so that it does not touch dishwasher motor

or lower part of dishwasher tub.

2. Pull direct wire through hole in terminal box.

Helpful Tip:

• Select the proper size twist-on

connectors to connect your

household wiring to 16-gauge

dishwasher wiring.

• Insert wire ends into twist-on

connector. Do not pre-twist bare

wire.

• Twist connector.

• Gently tug on wires to be sure both

are secured.

3. Connect the wires as follows using

twist-on connectors sized to

connect direct wire to 16-gauge dishwasher wire.

Power supply wire: Terminal box wire:

white _-> white

black _-> black

ground wire _-> ground connector

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector in

terminal box.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Form bare ground wire into a U-shaped hook. Wrap ground

wire hook clockwise around ground connector and under the

washer.

5. Securely tighten ground connector.

A. Ground wire

B. Washer

C. Ground connector

6. Tighten clamp connector or conduit connector screws.

A. Screws

7. Reinstall terminal box cover with wires inside terminal box.

The cover must be outside the box on the left side.

££Zi_£ZZZZZZZZZiC£ZZZZZZZZZIi_,_--X

8. Make sure no wires are pinched by the cover.

Option 2: Power Supply Cord

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug in a grounded 3 prong outlet.

2. Check that power supply cord does not touch dishwasher

motor or lower part of dishwasher tub.

snect Suppy

Helpful Tip:

Compression fittings:

a) Slide nut onto copper tubing about 1" (2.5 cm).

b) Slide ferrule onto the tubing. Do not position ferrule on

the end of the tubing.

c) Put the tubing into the elbow as far as it will go.

d) Slide the nut and ferrule forward and start the nut onto the

elbow threads. Be gentle when handling and positioning

the copper tubing, it bends and kinks easily.

A. Elbow

B. Ferrule

C. Nut

1. Toavoid vibration during operation, route the water supply line

so that it does not touch the dishwasher base, frame or motor.

2. With copper tubing pushed into compression fitting as far as it

will go, use a wrench and tighten compression fitting nut to

elbow on water inlet valve.

3. Place paper towel under elbow. Turn on water supply and

check for leaks.

_ _, _, _ _ _ 4 ¸ ,_

Co_ ect_, _o _,,__s_s_' _

1. To help minimize vibration, route drain hose to avoid contact

with motor, door springs, water line, cabinet, flooring or the

edge of the hole where it passes through the cabinet.

2. Do not remove drain loop from side of dishwasher.

A. Drain loop

Place pan under end of drain hose. Pan will collect any water

in drain hose.

Place the smaller drain hose clamp onto the small end of the

drain hose.

A\_

*\\

A. Hose clamp

Push the drain hose into the connector up to the stop on the

drain hose.

A. Connector

B. Stop

User pliers to open clamp and slide clamp onto connector

between stops on connector as shown.

A. Hose clamp

B. Stops

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

If you have not already done so, open dishwasher door and

place towel over pump assembly and spray arm of

dishwasher. This will keep screws from falling into pump area

when securing dishwasher to countertop.

Check that dishwasher is still level and centered side to side in

the opening.

Secure dishwasher to countertop or sides of cabinet with two,

#10 x V2"Phillips-head screws. The dishwasher must be

secured to keep it from tipping when door is opened. Do not

drop screws into bottom of dishwasher.

A. Screw to countertop

A. Screw to side cabinet

Open door about 3" (7.6 cm) and check that space between

inner door and tub is equal on both sides. If spacing is not

equal, loosen bracket screws and shift tub. Tighten bracket

screws.

If using a countertop attachment to secure dishwasher, check

that top of door does not contact screws, brackets, or

countertop. If it does, dishwasher must be lowered and re-

leveled.

If securing with aside attachment, check that sides of door do

not rub against the screw heads. If they do, dishwasher must

be re-centered. When dishwasher is properly centered,

replace plastic buttons.

A. Plasticbutton

7. Remove towel from dishwasher.

8. Reinstall the lower dish rack.

Check that grounding clip is attached to the lower panel.

Place the lower panel behind the access panel. Some models

have insulation on the access panel which must fall behind the

insulation on the lower panel.

A. Access panel

B. Lower panel

C. Grounding clip

3. Hold the two panels together and push them up against

dishwasher leg and vinyl pad.

4. Reinstall the screws through the holes in the access panel and

the slots in the lower panel. Install right side screw first.

5. Check that the lower edge of the lower panel contacts the

floor.

Tighten the screws.

DirectWire Method

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector in

terminal box.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Power Supply Cord Method

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

7. Reconnect power or plug in dishwasher.

Check Operation

1. Read the Use and Care Guide that came with your

dishwasher.

2. Check that all parts have been installed and no steps were

skipped.

3. Check that you have all the tools you used.

4. Start dishwasher and allow it to complete the shortest wash

cycle. After the first 2 minutes, unlatch door, wait 5 seconds,

then open door.

5. Check that there is water in the bottom of the dishwasher tub.

Check that dishwasher is working properly.

6. If not, disconnect power or unplug dishwasher and see "If

dishwasher does not operate" section.

If Dishwasher Does Not Operate

First try the solutions suggested here to possibly avoid the cost of

a service call.

• Has the circuit breaker tripped or the house fuse blown?

• Is the door closed tightly and latched?

• Has the cycle been set correctly to start the dishwasher?

• Is the water turned on?

If dishwasher still is not operating, call 1-866-664-2449.

La page charge ...

IKEA IUD9500WX0 Guide d'installation

Marque: IKEA

Modèle: IUD9500WX0

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: IKEA IUD9500WX0 Installation guide

IKEA IUD9500WX0 Guide d'installation

Ce manuel convient également à

IKEA IUD9500WX0 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents