MARAZZI LC15312HD1P2 Guide d'installation

LC15312HD1P2
MARAZZI
Marque
MARAZZI
Modèle
LC15312HD1P2
Taper
Guide d'installation
VitaElegante Grigio 6 in. x 24 in. and
12 in. x 24 in. tiles shown in brick pattern
Installation of
COUNTERTOP
& WALL TILE
INSTALLATION INSTRUCTIONS | COUNTERTOP & WALL TILE | PAGE 1 of 5
• Tile may be
installed over most
structurally sound
substrates.
• Make sure surface
is clean, smooth,
dry and free of
wax, soap scum
and grease.
• Any damaged,
loose or uneven
areas must be
repaired, patched
and leveled.
• Remove any
moldings, trim,
appliances or
anything that
could interfere
with installation.
•
Find the center point of the wall,
using a level to draw a plumb line
in the wall’s center.
• Lay out a row of loose tiles across
the bottom of the wall from the
center line leaving uniform joints
between tiles.
NOTE: Tiles can be butted together
leaving a consistent 1/16 in. joint
automatically.
TIP: If cuts leave tiles smaller than
half to their original size, adjust
the center line a half tile closer to
the wall.
• Stack two tiles here. At the top,
draw a horizontal line on the wall
and continue the line around all side
walls to be tiled.
STEP 1: SURFACE PREPARATION
1
STEP 2: WALL LAYOUT
2
CONTINUED ON NEXT PAGE
VitaElegante Grigio 6 in. x 24 in. and
12 in. x 24 in. tiles shown in brick pattern
Installation of
COUNTERTOP
& WALL TILE
INSTALLATION INSTRUCTIONS | COUNTERTOP & WALL TILE | PAGE 2 of 5
• Mix only enough adhesive
or mortar to be used
within 30 minutes.
• Using the type of trowel
recommended on the
adhesive package, spread
a 1/4 in. coat on the surface
of one grid area, using the
flat side of the trowel.
NOTE: Do not cover
guidelines or a larger
area than can be set in
15 minutes.
•
Use the notched side of
trowel to comb adhesive into
standing ridges by holding
trowel at a 45° angle.
• Remove excess adhesive,
leaving a uniform, ridged
setting bed.
STEP 4: APPLYING ADHESIVESTEP 3: COUNTERTOP LAYOUT
3 4
• Begin with counter trim, then
set full tiles from the first row
working back thus all cut tiles
will be placed on the back row
against the wall.
NOTE: Trim pieces are
available for use around
recessed appliances.
• S
nap parallel chalk lines on the
substrate as needed to keep
rows straight.
NOTE: Tile countertops should
have a tile backsplash at least 4
inches high for protection.
TIP: For backsplashes, match up
joints with the countertop tile.
CONTINUED ON NEXT PAGE
VitaElegante Grigio 6 in. x 24 in. and
12 in. x 24 in. tiles shown in brick pattern
Installation of
COUNTERTOP
& WALL TILE
INSTALLATION INSTRUCTIONS | COUNTERTOP & WALL TILE | PAGE 3 of 5
STEP 6: SETTING TILE
6
• Install tiles in the center, one grid at a
time. Finish each grid before moving to
the next. Start with the first tile in the
corner of the grid and work outward.
Set tiles one at a time using a slight
twisting motion.
NOTE: Don’t slide tiles into place.
• Insert tile spacers, as each tile is set,
or leave equal joints between tiles.
• Fit perimeter tiles in each grid last,
leaving 1/4 in. gap between tile and wall.
• When finished, tap in all tiles with a
rubber mallet or hammer and wood
block, to ensure a good bond and
level plane.
• Remove excess adhesive from joints
with a putty knife, and from tile with a
damp sponge.
• Do not use surface of tiles until they
are set (usually in 24 hours).
STEP 5: CUTTING TILE
5
• Carefully
measure tiles
and mark with
a pencil or
felt-tip pen.
• Make straight
or diagonal
cuts with a
tile cutter,
curved cuts
with a nipper
(chipping
away small
pieces for best
results), and
full-length
curved cuts
with a rod
saw. Smooth
out sharp-cut
edges with a
carborundum
stone.
CONTINUED ON NEXT PAGE
VitaElegante Grigio 6 in. x 24 in. and
12 in. x 24 in. tiles shown in brick pattern
Installation of
COUNTERTOP
& WALL TILE
INSTALLATION INSTRUCTIONS | COUNTERTOP & WALL TILE | PAGE 4 of 5
• Using the instructions on the
package, make enough grout to
use in about 30 minutes.
• Remove tile spacers and spread grout on
the tile surface, forcing down into joints
with a rubber grout float or squeegee.
• Tilt the float at a 45° angle and remove
excess grout from surface immediately
with the edge of float.
• Tilt it at a 90° angle and scrape it
diagonally across tiles.
• Wait 15–20 minutes for grout to set
slightly, then use a damp sponge to clean
grout residue from surface and smooth
the grout joints, rinsing sponge often.
•
Let dry until grout is hard and haze
forms on tile surface, then polish
with a soft cloth and wait 72 hours
for heavy use.
NOTE: Don’t apply sealers or polishes
for three weeks, and then only in
accordance with manufacturer’s
recommendations.
STEP 7: GROUTING JOINTS
7
STEP 8: INITIAL CLEANING
8
• The complete removal
of grout and construction
dirt after products have
been installed will improve
daily maintenance.
• Clean successfully by
scrubbing the installation
with hot water and a pH
neutral liquid cleaner
(soapless), followed by a
thorough rinsing, then remove
the rinse water with a wet
vacuum or dry toweling.
• If some residue remains,
further cleaning will need to
be done in consultation with
the grout manufacturer.
• For more aggressive
cleaning, scrubbing machines
equipped with nylon pads
or brushes should be used.
Wet vacuuming of the
suspended dirt and grout
is recommended.
CONTINUED ON NEXT PAGE
VitaElegante Grigio 6 in. x 24 in. and
12 in. x 24 in. tiles shown in brick pattern
Installation of
COUNTERTOP
& WALL TILE
INSTALLATION INSTRUCTIONS | COUNTERTOP & WALL TILE | PAGE 1 of 5
LEGAL
B
ATTENTION / ATENCIÓN / ATTENTION
Do not dry cut using motorized equipment due to the potential for exposure
to harmful silica dust. Use a wet saw or a score and snap tool when cutting is
necessary during the installation process.
No corte en seco usando equipo motorizado debido a la posibilidad de
exposición a polvo dañino de sílice. En caso de que sea necesario cortar durante
el proceso de instalación, usar una sierra de corte en húmedo o una herramienta
cortadora manual.
Ne pas couper à sec à l’aide d’un équipement motorisé en raison du risque
d’exposition à la poussière de silice nuisible. Utiliser une scie à eau ou un outil à
inciser et rompre lorsqu’il faut couper pendant le processus d’installation.
Back-butter spreading of a bond coat
to the back of a ceramic tile
before placing the tile to
ensure a strong bond with
the thin-set mortar.
Balanced cuts perimeter tile cut at equal
size and installed on
opposite sides of an area;
also, equally sized cuts on
each side of a miter.
Butt joint
a plain square joint
between two members
with no grout joint.
Grout
a mix used for filling tile
joints, commonly based
of cement.
Mortar a mixture of cement paste
and fine aggregate used to
bond masonry together.
Plumb perpendicular to true level.
Substrate the underlying support for
a ceramic tile installation
GLOSSARY OF TERMS
A
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

MARAZZI LC15312HD1P2 Guide d'installation

LC15312HD1P2
MARAZZI
Marque
MARAZZI
Modèle
LC15312HD1P2
Taper
Guide d'installation
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents