Flex FX1451 Manuel utilisateur

Marque: Flex

Modèle: FX1451

Catégorie: Clés à chocs électriques

Taper: Manuel utilisateur

Nous contacter /

Contáctenos

Model:

Modelo:

Modèle:

OPERATOR’S MANUAL

MANUAL DEL OPERADOR

MANUEL DE L’UTILISATEUR

833-FLEX-496

(833-3539-496)

For English

Version

See page 2

◆

Version

française

Voir page 18

◆

Versión en

español

Ver la página 36

www.Registermyﬂex.com

24V BRUSHLESS IMPACT WRENCH

CLÉ À CHOCS SANS BALAIS DE 24 V

LLAVE DE IMPACTO DE 24 V SIN ESCOBILLAS

FX1451

-2-

SAFETY SYMBOLS

The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols

and the explanations with them deserve your careful attention and understanding. The symbol

warnings do not, by themselves, eliminate any danger. The instructions and warnings they give are

no substitutes for proper accident prevention measures.

WARNING Be sure to read and understand all safety instructions in this Operator’s Manual,

including all safety alert symbols such as "DANGER," "WARNING," and

"CAUTION" before using this tool. Failure to follow all instructions listed below may result in electric

shock, re, and/or serious personal injury.

The denitions below describe the level of severity for each signal word. Please read the manual and

pay attention to these symbols.

This is the safety alert symbol. It is used to alert you to potential personal

injury hazards. Obey all safety messages that follow this symbol to avoid

possible injury or death.

DANGER DANGER indicates a hazardous situation which, if not avoided, will result in

death or serious injury.

WARNING WARNING indicates a hazardous situation which, if not avoided, could result

in death or serious injury.

CAUTION CAUTION, used with the safety alert symbol, indicates a hazardous situation

which, if not avoided, will result in minor or moderate injury.

Damage Prevention and Information Messages

These inform the user of important information and/or instructions that could lead to equipment or

other property damage if they are not followed. Each message is preceded by the word "NOTICE",

as in the example below:

NOTICE: Equipment and/or property damage may result if these instructions are not followed.

WARNING The operation of any power tools can result in foreign

objects being thrown into your eyes, which can result in

severe eye damage. Before beginning power tool operation, always wear

safety goggles or safety glasses with side shields and a full face shield when

needed. We recommend a Wide Vision Safety Mask for use over eyeglasses

or standard safety glasses with side shields. Always use eye protection which

is marked to comply with ANSI Z87.1.

-3-

GENERAL POWER TOOL SAFETY WARNINGS

WARNING Read all safety warnings, instructions, illustrations and specications

provided with this power tool. Failure to follow all instructions listed below may

result in electric shock, re and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery

operated (cordless) power tool.

Work area safety

Keep work area clean and well lit. Cluttered

or dark areas invite accidents.

Do not operate power tools in explosive

atmospheres, such as in the presence of

ammable liquids, gases or dust. Power

tools create sparks which may ignite the dust or

fumes.

Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

Electrical safety

Power tool plugs must match the outlet.

Never modify the plug in any way. Do

not use any adapter plugs with earthed

(grounded) power tools. Unmodied plugs

and matching outlets will reduce risk of electric

shock.

Avoid body contact with earthed or

grounded surfaces, such as pipes, radiators,

ranges and refrigerators. There is an

increased risk of electric shock if your body is

earthed or grounded.

Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the

power tool. Keep cord away from heat, oil,

sharp edges or moving parts. Damaged or

entangled cords increase the risk of electric

shock.

When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

If operating a power tool in a damp location

is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of a

GFCI reduces the risk of electric shock.

Personal safety

Stay alert, watch what you are doing and

use common sense when operating a power

tool. Do not use a power tool while you are

tired or under the inuence of drugs, alcohol

or medication. A moment of inattention while

operating power tools may result in serious

personal injury.

Use personal protective equipment. Always

wear eye protection. Protective equipment such

as a dust mask, non-skid safety shoes, hard

hat or hearing protection used for appropriate

conditions will reduce personal injuries.

Prevent unintentional starting. Ensure

the switch is in the off-position before

connecting to power source and/or battery

pack, picking up or carrying the tool.

Carrying power tools with your nger on the

switch or energizing power tools that have the

switch on invites accidents.

Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool

may result in personal injury.

Do not overreach. Keep proper footing

and balance at all times. This enables

better control of the power tool in unexpected

situations.

Dress properly. Do not wear loose clothing

or jewelry. Keep your hair and clothing away

from moving parts. Loose clothes, jewelry or

long hair can be caught in moving parts.

If devices are provided for the connection

of dust extraction and collection facilities,

ensure these are connected and properly

used. Use of dust collection can reduce

dust-related hazards.

Do not let familiarity gained from frequent

use of tools allow you to become

complacent and ignore tool safety

principles. A careless action can cause severe

injury within a fraction of a second.

-4-

Power tool use and care

Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

Do not use the power tool if the switch

does not turn it on and off. Any power tool

that cannot be controlled with the switch is

dangerous and must be repaired.

Disconnect the plug from the power

source and/or remove the battery pack,

if detachable, from the power tool before

making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions

to operate the power tool. Power tools are

dangerous in the hands of untrained users.

Maintain power tools and accessories.

Check for misalignment or binding of

moving parts, breakage of parts and any

other condition that may affect the power

tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are

caused by poorly maintained power tools.

Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

Use the power tool, accessories and

tool bits etc. in accordance with these

instructions, taking into account the working

conditions and the work to be performed.

Use of the power tool for operations different

from those intended could result in a hazardous

situation.

Keep handles and grasping surfaces dry,

clean and free from oil and grease. Slippery

handles and grasping surfaces do not allow

for safe handling and control of the tool in

unexpected situations.

Battery tool use and care

Recharge only with the charger specied by

the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of re

when used with another battery pack.

Use power tools only with specically

designated battery packs. Use of any other

battery packs may create a risk of injury and

re.

When battery pack is not in use, keep it

away from other metal objects, like paper

clips, coins, keys, nails, screws or other

small metal objects, that can make a

connection from one terminal to another.

Shorting the battery terminals together may

cause burns or a re.

Under abusive conditions, liquid may be

ejected from the battery; avoid contact.

If contact accidentally occurs, ush with

water. If liquid contacts eyes, additionally

seek medical help. Liquid ejected from the

battery may cause irritation or burns.

Do not use a battery pack or tool that is

damaged or modied. Damaged or modied

batteries may exhibit unpredictable behavior

resulting in re, explosion or risk of injury.

Do not expose a battery pack or tool to re

or excessive temperature. Exposure to re or

temperature above 265 °F (130 °C) may cause

explosion.

Follow all charging instructions and do

not charge the battery pack or tool outside

the temperature range specied in the

instructions. Charging improperly or at

temperatures outside the specied range may

damage the battery and increase the risk of re.

Service

Have your power tool serviced by a

qualied repair person using only identical

replacement parts. This will ensure that the

safety of the power tool is maintained.

Never service damaged battery packs.

Service of battery packs should only be

performed by the manufacturer or authorized

service providers.

-5-

SAFETY WARNINGS FOR IMPACT WRENCH

Hold the power tool by insulated gripping

surfaces, when performing an operation

where the fastener may contact hidden

wiring. Fasteners contacting a “live” wire may

make exposed metal parts of the power tool

“live” and could give the operator an electric

shock.

WARNING

• Some dust created by power sanding, sawing,

grinding, drilling and other construction

activities contains chemicals known to the

State of California to cause cancer, birth

defects or other reproductive harm. Some

examples of these chemicals are:

– Lead from lead-based paints.

– Crystalline silica from bricks, cement, and

other masonry products.

– Arsenic and chromium from chemically-treated

lumber.

• Your risk from these exposures varies,

depending upon how often you do this type

of work. To reduce your exposure to these

chemicals:

– Work in a well-ventilated area.

– Work with approved safety equipment, such

as dust masks that are specially designed to

lter out microscopic particles.

– Avoid prolonged contact with dust from power

sanding, sawing, grinding, drilling, and other

construction activities. Wear protective clothing

and wash exposed areas with soap and water.

Allowing dust to get into your mouth or eyes or

to lie on the skin may promote absorption of

harmful chemicals.

-6-

SYMBOLS

IMPORTANT: Some of the following symbols may be used on your tool. Please study them and

learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better

and safer.

Symbol Name Designation/Explanation

V Volts Voltage

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

kg Kilograms Weight

min Minutes Time

s Seconds Time

Wh Watt-hours Battery capacity

Ah Ampere-hours Battery capacity

ø Diameter Size of drill bits, grinding wheels, etc.

n0No load speed Rotational speed, at no load

n Rated speed Maximum attainable speed

…/min Revolutions or reciprocations per

minute (rpm)

Revolutions, strokes, surface speed, orbits,

etc. per minute

O Off position Zero speed, zero torque...

1,2,3,…

Ⅰ,Ⅱ,Ⅲ, Selector settings Speed, torque, or position settings. Higher

number means greater speed

Innitely variable selector with off Speed is increasing from 0 setting

Arrow Action in the direction of arrow

Alternating current (AC) Type or a characteristic of current

Direct current (DC) Type or a characteristic of current

Alternating or direct current

(AC / DC) Type or a characteristic of current

Class II tool Designates Double Insulated Construction

tools.

Protective earth Grounding terminal

Li-ion RBRC seal Designates Li-ion battery recycling

program

Read the instructions Alerts user to read manual

-7-

Symbol Name Designation/Explanation

Wear eye protection symbol Alerts user to wear eye protection

Wear ear protection Always wear sound barriers (ear plugs or

ear mufers) to protect your hearing.

Always operate with two hands Alerts user to always operate with two

hands

Do not use the guard for cut-off

operations Do not use the guard for cut-off operations

SYMBOLS (CERTIFICATION INFORMATION)

Symbol Designation/Explanation

This symbol designates that this tool is listed by Underwriters Laboratories.

This symbol designates that this component is recognized by Underwriters

Laboratories.

This symbol designates that this tool is listed by Underwriters Laboratories, to

United States and Canadian Standards.

This symbol designates that this tool is listed by the Canadian Standards

Association.

This symbol designates that this tool is listed by the Canadian Standards

Association, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Intertek Testing Services,

to United States and Canadian Standards.

-8-

FUNCTIONAL DESCRIPTIONS AND SPECIFICATIONS

IMPACT WRENCH

Fig. 1

1/2" Square

Drive

Direction-of-Rotation

(Forward/Center-lock/

Reverse) Selector

Strap Fixing

For attaching a wrist strap (not

included) in order to reduce the

chances of dropping your tool.

Variable-speed Trigger

Switch Drive

Speed Control

Panel

LED Light

Removable

Belt Clip

Model No. FX1451

Rated Voltage 24 V d. c.

Square Drive 1/2’’ (12.7 mm)

No-load Speed 0-450/1600/2700/min (RPM)

Impacts per minute 0-3100/min (IPM)

Maximum torque 600 in.lbs

Recommended operating temperature -4 – 104 °F (-20 – 40 ℃)

Recommended storage temperature 122 ℉ (< 50 ℃)

NOTE: All charging times are subject to environmental temperature and the battery pack condition.

-9-

ASSEMBLY

WARNING Detach the battery pack

from the tool before

making any assembly, adjustments or

changing accessories. Such preventive safety

measures reduce the risk of starting the tool

accidentally.

TO ATTACH/DETACH BATTERY PACK (FIG. 2)

Lock the variable-speed trigger switch “OFF”

on the tool by placing the direction-of-rotation

(forward/center-lock/reverse) selector in the

center position before attaching or detaching

the battery pack.

To attach the battery pack:

Align the raised rib on the battery pack with the

grooves in the tool, and then slide the battery

pack onto the tool.

NOTICE: When placing the battery pack

onto the tool, be sure that the raised rib

on the battery pack aligns with the groove

inside the tool and that the latches snap into

place properly. Improper attachment of the

battery pack can cause damage to internal

components.

To detach the battery pack:

Depress the battery-release button located

on the front of the battery pack, to release the

battery pack. Pull the battery pack out and

remove it from the tool.

REMOVABLE BELT CLIP (FIG. 3)

Your tool is equipped with a removable belt clip

that can be positioned on the side of the tool for

convenient transport.

Install the belt clip onto the tool:

a. Remove the battery pack from the tool.

b. Align the rib and the hole of the belt clip with

the opening and the threaded hole on the

base of the tool, respectively.

c. Insert the screw and securely tighten the

screw with a screwdriver (not included).

Remove the belt clip from the tool:

a. Remove the battery pack from the tool.

b. Use a screwdriver to loosen the screw that

attaches the belt clip to the impact wrench.

c. Remove the screw and the belt clip.

Fig. 2

Attach

DetachBattery-release

Button

Fig. 3

Opening

Rib

Removable Belt Clip

-10-

INSTALL AND REMOVE THE IMPACT

SOCKET (FIG. 4)

CAUTION Make sure that the impact

socket and the mounting

portion are not damaged before installing

the impact socket.

To install the impact socket:

a. Align the square of the impact socket with the

square drive and push the impact socket onto

the square drive as far as it will go.

b. Tap it lightly if required.

To remove the impact socket:

Simply pull it off.

WARNING Wear protective gloves

when removing the impact

socket from the tool, or rst allow the impact

socket to cool down. The impact socket may

be hot after prolonged use.

Fig. 4

Impact socket

Square drive

-11-

ADJUSTMENTS

DIRECTION-OF-ROTATION (FORWARD/

CENTER-LOCK/REVERSE) SELECTOR

WARNING After tool use, lock the

direction-of-rotation

selector in the “OFF” position (center-lock)

to help prevent accidental starts and

possible injury.

Your tool is equipped with a direction-of-rotation

selector, located above the variable-speed

trigger switch. This selector is used to change

the direction of rotation of the bit and to lock the

variable-speed trigger in the “OFF” (center-lock)

position.

a. Position the direction-of-rotation selector to

the far left of the tool to tighten bolts/nuts (Fig.

5).

b. Position the direction-of-rotation selector to

the far right of the tool to loosen bolts/nuts

(Fig. 5).

c. Position the switch in the “OFF” (center-

lock) position to help reduce the possibility of

accidental starting when not in use.

NOTICE: To prevent gear damage, always allow

the impact wrench to come to a complete stop

before changing the direction of rotation.

NOTICE: The impact wrench will not run unless

the direction-of-rotation selector is engaged fully

to the left or to the right.

WARNING Battery tools are always in

operating condition.

Therefore, the direction-of-rotation (forward/

center-lock/reverse) selector should always

be locked in the center position when the

tool is not in use or when carrying it at your

side.

VARIABLE-SPEED TRIGGER SWITCH (FIG. 6)

Your tool is equipped with a variable-speed

trigger switch. The tool can be turned ON or

OFF by depressing or releasing the variable

speed trigger switch.

The variable-speed trigger switch delivers

higher speed with increased trigger pressure

and lower speed with decreased trigger

pressure.

Fig. 5

Fig. 6

Variable-speed

Trigger Switch

-12-

LED LIGHT (FIG. 7)

Your tool is equipped with the LED work light.

This provides additional light on the surface of

the workpiece for operation in lower-light areas.

The LED work light will automatically turn on

with a slight squeeze on the trigger switch

before the tool starts running. It will turn off

approximately 10 seconds after the trigger

switch is released.

a. The LED light will rapidly ash when the tool

and/or battery pack becomes overloaded or

too hot, and the internal sensors will turn the

tool off. Rest the tool for a while or place the

tool and battery pack separately under air ow

to cool them.

b. The LED light will ash more slowly to indicate

that the battery pack charge is at low capacity.

Recharge the battery pack.

c. If the LED light does not turn on when you

start the tool, or it turns off suddenly during

operation, please contact customer service or

an authorized service center for assistance.

MODE SELECTION (FIG. 8)

Your tool is equipped with a speed control

panel, located on the foot of the tool. It consists

of the drive-control button, the “A” button, and

LED indicators for working modes.

The drive-control button is used to select among

three modes with preset torque, rotation-speed

(RPM), and impact-speed (IPM) for intended

application. The modes 1, 2, and 3 are the only

modes where the speed is controlled by the

variable-speed trigger switch.

To select the drive control mode:

a. First, check the active mode. Either depress

and release the trigger switch or press the

drive control button (or the “A” button) directly

without touching the trigger switch. The

LED indicator below the mode number will

illuminate to indicate the active mode.

b. Press the drive-control button briey (less

than 0.5 second) to cycle through three

modes. Each press changes one torque level.

“A” is a special mode, that is designed to be

used both with forward rotation for tightening the

bolts or nuts and reverse rotation for loosening

the bolts or nuts.

In the forward rotation position, the impact

wrench will stop running when the bolt or nut is

pre-tightened, and then the torque wrench can

be used to complete the work. This function has

high work efciency and the bolt or nut will not

be over-tightened.

In the reverse rotation position, once the bolt or

nut becomes loose, the impact wrench will stop

running to prevent bolt or nut from falling away.

Fig. 7

Fig. 8

LED- indicator

Drive-control button “A” Button

-13-

To select the “A” mode:

First, check the active mode. Either depress

and release the trigger switch or press the

drive control button or the “A” directly without

touching the trigger switch. The LED indicator

beside the “A” button will illuminate to indicate

the current mode setting. See more details in

the chart below:

Forward Rotation

LED indicator

displayed on panel Working

Mode Application

1 Fine-tuned tightening of small bolts and nuts

2When tightening, the torque is moderate.

3When tightening, the torque is maximum.

A Tightening with automatic stop.

Reverse Rotation

LED indicator

displayed on panel Working

Mode Application

1 Fine-tuned loosening of small bolts and nuts

2When loosening, the torque is moderate.

3When loosening, the torque is maximum.

A Loosening with automatic stop.

ON ; OFF

WARNING Do not change the working

mode while the tool is

running. Sudden change of torque may cause

the loss of control causing possible injury or

damage to the tool or workpiece.

NOTE: The LED indicator(s) will turn off

approximately 1 min after the trigger switch is

released.

NOTE: When the tool is turned on after a break,

the working mode will revert to the last used

setting.

-14-

OPERATING INSTRUCTIONS

WARNING To reduce the risk of re,

personal injury, and

product damage due to a short circuit, never

immerse your charger or battery pack in

uid or allow a uid to ow inside them.

Corrosive or conductive uids, such as

seawater, certain industrial chemicals, and

bleach or bleach-containing products, etc. can

cause a short circuit.

WARNING If any parts are damaged

or missing, do not operate

this product until the parts are replaced. Use

of this product with damaged or missing parts

could result in serious personal injury.

WARNING Do not attempt to modify

the charger or create

accessories not recommended for use with

this charger. Any such alteration or

modication is misuse and could result in a

hazardous condition leading to possibly serious

personal injury.

WARNING To prevent accidental

starting that could cause

serious personal injury, always remove the

battery pack from the tool when assembling

parts.

This impact wrench must be used only with the battery packs and chargers listed below:

Battery Pack Charger

2.5Ah 3.5Ah 5.0Ah 6Ah 8.0Ah 10Ah 12Ah

FX0111 FX0321 FX0121 FX0331 FX0221 FX0341 FX0231 FLEX

FX0411

FLEX

FX0421

FLEX

FX0431

NOTICE: Please refer to the battery pack and charger manuals for detailed operating

information.

TIGHTEN AND LOOSEN NUTS AND BOLTS

(FIG. 9)

To tighten nuts and bolts

Use the hex socket that matches the nut or bolt.

Select a proper working mode or “A” mode

depending on the type or size of the bolt and

nut. Before starting your job, always perform a

test operation to determine the proper fastening

time for your bolt or nut.

a. Set the direction-of-rotation selector to

forward setting.

b. Hold the tool rmly and place the socket over

the bolt or nut. Ensure that full length of the

bolt head or nut is fully engaged into socket.

c. Depress the variable-speed trigger switch

to turn the impact wrench on. Start slowly,

increasing the speed as the nut or bolt runs

downs. Set the nut or bolt snugly by slowing

the tool to a stop.

WARNING If this procedure is not

followed, the tool will have

a tendency to torque or twist in your hands.

d. Fasten the bolt or nut to the proper torque.

e. After fastening, always check the torque with

a torque wrench. If the fasteners are too tight,

reduce the impacting time. If they are not tight

enough, increase the impacting time.

NOTICE: Hold the tool straight along the axis

of the bolt or nut.

NOTICE: Excessive fastening torque may

damage the bolt/nut or socket.

Fig. 9

-15-

TO LOOSEN NUTS AND BOLTS

Use either mode 1, 2, 3 or “A” mode to loosen

nuts and bolts depending on the application.

When working overhead or working on car

tires, to prevent the loosened fasteners from

falling to the ground or into a tight space, it is

recommended to use the “A” mode to do this

job.

a. Set the direction-of-rotation to reverse setting.

b. Hold the tool rmly and place the socket over

the bolt or nut. Ensure that full length of the

bolt head or nut is fully engaged into socket.

c. Depress the variable-speed trigger switch to

turn the impact wrench on. Once the fastener

is loose, the tool will stop running. This tool

also allows you to continue to depress the

trigger switch for removing the nut from the

long bolt, if necessary.

-16-

MAINTENANCE

WARNING To avoid serious personal

injury, always remove the

battery pack from the tool when cleaning or

performing any maintenance.

SERVICE

WARNING Preventive maintenance

performed by unauthorized

personnel may result in misplacing of

internal wires and components which could

cause a serious hazard. We recommend that

all tool service be performed by a FLEX Factory

Service Center or Authorized FLEX Service

Station.

GENERAL MAINTENANCE

WARNING When servicing, use only

identical replacement

parts. Use of any other parts could create a

hazard or cause product damage. Periodically

inspect the entire product for damaged, missing,

or loose parts such as screws, nuts, bolts, caps,

etc. Tighten securely all fasteners and caps and

do not operate this product until all missing or

damaged parts are replaced. Please contact

customer service or an authorized service

center for assistance.

WARNING To avoid serious personal

injury, always remove the

battery pack from the charger/tool when

cleaning or performing any maintenance.

CLEANING

WARNING The tool may be cleaned

most effectively with

compressed dry air. Always wear safety

goggles when cleaning tools with

compressed air. Ventilation openings and

switch levers must be kept clean and free of

foreign matter. Do not attempt to clean by

inserting pointed objects through openings.

WARNING Certain cleaning agents

and solvents damage

plastic parts. Some of these are: gasoline,

carbon tetrachloride, chlorinated cleaning

solvents, ammonia and household detergents

that contain ammonia.

STORAGE

Store the tool indoors in a place that is

inaccessible to children. Keep away from

corrosive agents.

-17-

FLEX LIMITED WARRANTY

Chervon North America, Inc. ("Seller") warrants to the original purchaser only, that all FLEX 24V

products will be free from defects in material or workmanship for a period of ve years from date of

purchase when the original purchaser registers the product within 30 days from the date of original

retail purchase and retains their receipt as proof of purchase. THE 5-YEAR LIMITED WARRANTY

PERIOD IS CONDITIONED ON REGISTRATION OF THE PRODUCT WITHIN 30 DAYS OF

PURCHASE AND ONLY APPLICABLE TO FLEX 24V TOOLS, BATTERIES AND CHARGERS. If the

original purchaser does not register their product within 30 days, the foregoing limited warranty will

apply for a duration of three years. Product registration can be completed online at

www.registermyex.com.

24V Tools: 5-Year Limited Warranty with Registration

24V Batteries and Chargers: 5-Year Limited Warranty with Registration

Corded, 12V and 20V FLEX Legacy Products: 1-Year Limited Warranty, No Registration Benet

FLEX STACK PACK™ Storage System: 1-Year Limited Warranty with Registration

Accessories and Attachments: No Warranty

SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this Limited Warranty

and, to the extent permitted by law, any warranty or condition implied by law, shall be the repair or

replacement of parts, without charge, which are defective in material or workmanship and which

have not been misused, carelessly handled, or repaired by persons other than a FLEX Authorized

Service Dealer. This warranty does not cover part failure due to normal wear and tear. To make a

claim under warranty, return the complete product, transportation prepaid, to any FLEX Authorized

Service Dealer. For Authorized FLEX Service Dealers, please visit www.registermyex.com or call

1-833-FLEX-496 (1-833-353-9496).

The 5-Year Limited Warranty does not apply to accessories, attachments or parts.

The 1-Year limited warranty for FLEX STACK PACK™ Storage System covers only tool boxes and

does not apply to system attachments and power tool accessories.

Any implied warranties applicable to a product shall be limited in duration equal to the duration of the

express warranties applicable to such product, as set forth in the rst paragraph above. Some states

in the U.S. and some Canadian provinces do not allow limitations on how long an implied warranty

lasts, so the above limitation may not apply.

FLEX is not responsible for direct, indirect, incidental or consequential damages. Some U.S. states

and Canadian provinces do not allow limitations on how long an implied warranty lasts and/or do

not allow the exclusion or limitation of incidental or consequential damages, so the above limitations

or exclusions may not apply. This limited warranty gives you specic legal rights, and you may also

have other rights which vary by state in the U.S. and by province in Canada.

This limited warranty applies only to products sold within the United States of America, Canada and

the commonwealth of Puerto Rico. For warranty coverage within other countries, contact your local

FLEX dealer.

www.expowertools.com

www.registermyex.com

1-833-FLEX-496 (1-833-353-9496)

-18-

SYMBOLES RELATIFS À LA SÉCURITÉ

La raison d’être des symboles relatifs à la sécurité est d’attirer votre attention sur des dangers

possibles. Il est important de vous familiariser avec les symboles relatifs à la sécurité et les

explications qui les accompagnent an de bien les comprendre. Les avertissements et les symboles

associés ne sufsent pas à éliminer tous les dangers. Les instructions et les avertissements qu’ils

donnent ne sauraient remplacer des mesures de prévention des accidents appropriées.

AVERTISSEMENT Lisez toutes les consignes de sécurité qui sont contenue dans ce

Mode d’emploi, y compris tous les symboles d’alerte relatifs à la

sécurité tels que « DANGER », « AVERTISSEMENT » et « MISE EN GARDE », et assurez-vous

que vous les comprenez bien avant de commencer à utiliser cet outil. La non-observation de toutes

les instructions gurant ci-après pourrait causer un choc électrique, un incendie et/ou des blessures

personnelles graves.

Les dénitions ci-dessous décrivent le niveau de gravité pour chaque terme signalant un danger.

Veuillez lire le mode d’emploi et lire la signication de ces symboles.

C’est le symbole d’alerte relatif à la sécurité. Il est utilisé pour vous

avertir de l’existence possible d’un danger de lésion corporelle.

Obéissez à tous les messages relatifs à la sécurité qui suivent ce

symbole pour éviter tout risque de blessure ou même de mort.

DANGER DANGER indique une situation dangereuse qui, si elle n’est pas

évitée, causera la mort d’une personne ou une blessure grave.

AVERTISSEMENT AVERTISSEMENT indique une situation dangereuse qui, si elle

n’est pas évitée, causera la mort d’une personne ou une blessure

grave.

MISE EN GARDE MISE EN GARDE, conjointement avec le symbole d’alerte en

liaison avec la sécurité, indique une situation dangereuse qui, si

elle n'est pas évitée, causera une blessure légère ou modérée.

Messages d’information et de prévention des dommages

Ils informent l’utilisateur d’informations et/ou d’instructions importantes qui pourraient entraîner des

dommages matériels ou aux équipements s’ils ne sont pas suivis. Chaque message est précédé par

le terme « AVIS », comme dans l’exemple ci-dessous :

AVIS : Un dommage matériel et/ou aux équipements peut survenir si ces instructions ne sont pas

suivies.

AVERTISSEMENT Pendant leur fonctionnement, les outils

électriques peuvent projeter des corps

étrangers dans les yeux de leur utilisateur et lui iniger de graves blessures

aux yeux. Portez toujours des lunettes de protection ou des lunettes de

sécurité à écrans latéraux et un masque couvrant tout le visage lors de

l’utilisation de ce produit. Nous recommandons de porter un masque de

sécurité à vision latérale large au-dessus des lunettes ordinaires ou des

lunettes de sécurité standard avec des écrans de protection sur les côtés.

Utilisez toujours un équipement de protection des yeux indiquant qu’il est

conforme à la norme ANSI Z87.1.

-19-

AVERTISSEMENTS GÉNÉRAUX RELATIFS À LA SÉCURITÉ POUR

LES OUTILS ÉLECTRIQUES

AVERTISSEMENT Lisez tous les avertissements relatifs à la sécurité, les

instructions, les illustrations et les spécications fournies avec

cet outil électrique. Le non-respect de toutes les instructions gurant ci-après pourrait causer un

choc électrique, un incendie et/ou des blessures graves.

CONSERVEZ TOUS LES AVERTISSEMENTS ET TOUTES LES INSTRUCTIONS

POUR RÉFÉRENCE FUTURE.

Le terme « outil électrique » dans les avertissements fait référence à votre outil électrique à cordon

électrique branché dans une prise secteur ou à votre outil électrique à piles (sans l).

Sécurité de la zone de travail

Gardez votre zone de travail propre et bien

éclairée. Des zones encombrées ou sombres

sont propices aux accidents.

N’utilisez pas des outils électriques dans

une atmosphère explosive, par exemple

en présence de liquides, de gaz ou de

poussières inammables. Les outils

électriques produisent des étincelles qui

risquent de mettre feu aux poussières ou aux

émanations de fumée.

Gardez les enfants et autres personnes

présentes à une distance sufsante lorsque

vous utilisez un outil électrique. Des

distractions risqueraient de vous faire perdre le

contrôle.

Sécurité électrique

La che de l’outil électrique doit

correspondre à la prise de courant. Ne

modiez jamais une che de quelque façon

que ce soit. N’utilisez pas d’adaptateurs

de ches avec des outils électriques mis

à la terre/à la masse. L’emploi de ches non

modiées et de prises de courant correspondant

naturellement aux ches réduira le risque de

choc électrique.

Évitez tout contact de votre corps avec des

surfaces mises à la terre ou à la masse telles

que des surfaces de tuyaux, de radiateurs,

de cuisinières et de réfrigérateurs. Il existe un

risque accru de choc électrique si votre corps

est en contact avec la terre ou la masse.

N’exposez pas d’outils électriques à la

pluie ou à un environnement humide. La

pénétration d’eau dans un outil électrique

augmentera le risque de choc électrique.

N’utilisez pas le cordon de façon abusive.

N’utilisez pas le cordon pour porter, tirer

ou débrancher l’outil électrique. Tenez

le cordon à distance de toute source de

chaleur, d’huile, de bords tranchants ou de

pièces mobiles. Des cordons endommagés

ou entortillés augmentent le risque de choc

électrique.

Lorsque vous utilisez un outil électrique à

l’extérieur, employez un cordon de rallonge

approprié pour un emploi à l’extérieur.

L’utilisation d’un cordon approprié pour une

utilisation à l’extérieur réduit le risque de choc

électrique.

S’il est inévitable d’utiliser un outil

électrique dans un environnement humide,

utilisez une alimentation protégée par un

disjoncteur de circuit de fuite à la terre.

L’utilisation d’un tel circuit réduit le risque de

choc électrique.

Sécurité personnelle

Faites preuve de vigilance et de bon sens, et

observez attentivement ce que vous faites

lorsque vous utilisez un outil électrique.

N’utilisez pas un outil électrique si vous êtes

fatigué(e) ou sous l’inuence de drogues,

d’alcool ou de médicaments. Un simple

moment d’inattention pendant que vous utilisez

un outil électrique pourrait causer une blessure

grave.

Utilisez des équipements de protection

personnelle. Portez toujours des

équipements de protection des yeux.

Des équipements de protection tels qu’un

masque de protection contre la poussière, des

chaussures de sécurité antidérapantes, un

casque ou un dispositif de protection de l’ouïe

utilisés en fonction des conditions réduiront le

nombre des blessures.

-20-

Prévenez une mise en marche accidentelle.

Assurez-vous que l’interrupteur est dans la

position d’arrêt (OFF) avant de connecter

l’appareil à une source d’alimentation et/

ou à un bloc-piles, de le soulever ou de le

transporter. Le fait de transporter des outils

électriques avec le doigt sur l’interrupteur ou de

mettre sous tension des outils électriques avec

l’interrupteur en position de marche invite les

accidents.

Retirez toute clé de réglage pouvant être

attachée à l’outil avant de mettre l’outil

électrique sous tension. Une clé laissée

attachée à une pièce en rotation de l’outil

électrique pourrait causer une blessure.

Ne faites rien qui risquerait de vous faire

perdre l’équilibre. Veillez à toujours garder

un bon équilibre et un appui stable. Ceci

permet de mieux contrôler l’outil électrique dans

des situations inattendues.

Portez des vêtements appropriés. Ne portez

pas de bijoux ou de vêtements amples.

Gardez vos cheveux et vos vêtements à une

distance sufsante des pièces mobiles. Les

vêtements amples, bijoux ou cheveux longs

pourraient être attrapés par des pièces mobiles.

Si des dispositifs sont fournis pour le

raccordement d’accessoires d’extraction et

de collecte de la poussière, assurez-vous

qu’ils sont connectés et utilisés de façon

appropriée. L’emploi correct de l’accessoire

de collecte de la poussière peut réduire les

dangers associés à la poussière.

Ne laissez pas la familiarité résultant de

l’utilisation fréquente des outils vous inciter

à devenir complaisant(e) et à ignorer les

principes de sécurité des outils. Une action

négligente pourrait causer des blessures graves

en une fraction de seconde.

Utilisation et entretien de l’outil

électrique

N’imposez pas de contraintes excessives

à l’outil électrique. Utilisez l’outil électrique

approprié pour votre application. L’outil

électrique correct fera le travail plus

efcacement et avec plus de sécurité à

la vitesse à laquelle il a été conçu pour

fonctionner.

N’utilisez pas l’outil électrique si

l’interrupteur de marche/arrêt ne permet pas

de le mettre sous tension/hors tension. Tout

outil électrique qui ne peut pas être contrôlé

par son interrupteur est dangereux et doit être

réparé.

Débranchez la che de la prise secteur et/

ou retirez le bloc-piles de l’outil électrique

(s’il est amovible) avant d’y apporter de

quelconques modications, de changer

d’accessoire ou de ranger l’outil électrique.

De telles mesures de sécurité préventives

réduisent le risque de déclenchement accidentel

de l’outil électrique.

Rangez les outils électriques qui ne sont

pas utilisés activement hors de portée des

enfants, et ne laissez aucune personne

n’ayant pas lu ces instructions et ne sachant

pas comment utiliser un tel outil se servir de

cet outil. Les outils électriques sont dangereux

quand ils sont entre les mains d’utilisateurs

n’ayant pas reçu la formation nécessaire à leur

utilisation.

Entretenez de façon appropriée les outils

électriques et les accessoires.

Assurez-vous que les pièces en mouvement

sont bien alignées et qu’elles ne se

coincent pas, qu’il n’y a pas de pièces

cassées ou qu’il n’existe aucune situation

pouvant affecter le fonctionnement de

l’outil électrique. Si l’outil électrique est

endommagé, faites-le réparer avant de vous

en servir à nouveau. De nombreux accidents

sont causés par des outils électriques mal

entretenus.

Gardez les outils de coupe tranchants et

propres. Des outils de coupe entretenus de

façon adéquate avec des bords de coupe

tranchants sont moins susceptibles de se

coincer et sont plus faciles à contrôler.

Utilisez l’outil électrique, les accessoires,

les mèches de perçage, etc. conformément

à ces instructions, en tenant compte

des conditions de travail et de la tâche à

accomplir. L’utilisation de l’outil électrique

pour des opérations différentes de celles pour

lesquelles il est conçu pourrait causer une

situation dangereuse.

Gardez les poignées et les surfaces de

préhension propres, sèches et exemptes

de toute trace d’huile ou de graisse. Les

poignées et les surfaces de préhension

glissantes ne permettent pas une manipulation

et un contrôle sûrs de l’outil dans des situations

inattendues.

La page charge ...

Flex FX1451 Manuel utilisateur

Marque: Flex

Modèle: FX1451

Catégorie: Clés à chocs électriques

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Flex FX1451 User manual
español: Flex FX1451 Manual de usuario

Flex FX1451 Manuel utilisateur

Flex FX1451 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents