Shenzhen BL-R8822BU1-A WIFI Module Manuel utilisateur

Marque: Shenzhen

Modèle: BL-R8822BU1-A WIFI Module

Taper: Manuel utilisateur

Shenzhen KTC Commercial Display Technology CO.,LTD.

WIFI Module

Model Number: BL-R8822BU1-A

Product Descrition

：

BL-R8822BU1-A module design is based on Realtek RTL8822BU solution, The RTL8822BU is a

highly integrated single chip which has built in a 2x2 dual-band wireless LAN radio and

Bluetooth radio. It includes Bluetooth EDR and LE radio which complies with Bluetooth

v2.1+EDR, v3.0, v4.0+BLEand V4.2.The Module is a highly integrated MAC/BBP and 2.4/5GHz

PA/LNA single chip which supportsa 433.3Mbps PHY rate. The Module is designed to support

standard-based features in the areas of security, quality of service, and international

regulations, giving end users the greatestperformance anytime and in any circumstance. This

documentation describes the engineering requirements specification.

Product Specification

For BT_EDR

Frequency Band:

2400 MHz to 2483.5 MHz

Frequency Range:

2402 MHz to 2480 MHz

Bluetooth Version:

Bluetooth EDR

Modulation Technique:

Frequency Hopping Spread Spectrum(FHSS)

Type of Modulation:

GFSK, π/4DQPSK, 8DPSK

Number of Channels: 79

Channel Separation:

1 MHz

Antenna Type: PCB Antenna

Antenna Gain:

2.5 dBi

Maximum Peak Power:

2 dBm

For 2.4 GHz ISM Band of Wi-Fi

Frequency Band: 2400 MHz to 2483.5 MHz

Frequency Range:

2412 MHz to 2462 MHz

Support Standards: IEEE 802.11b, IEEE 802.11g, IEEE 802.11n-

HT20, IEEE

802.11n-HT40

For BT_LE

Frequency Band:

2400 MHz to 2483.5 MHz

Frequency Range: 2402 MHz to 2480 MHz

Bluetooth Version:

Bluetooth LE

Type of Modulation:

GFSK

Number of Channels: 40

Channel Separation:

2 MHz

Antenna Type:

PCB Antenna

Antenna Gain:

2.5 dBi

Maximum Peak Power:

1 dBm

Shenzhen KTC Commercial Display Technology CO.,LTD.

Type of Modulation:

IEEE 802.11b: DSSS(CCK, DQPSK, DBPSK)

IEEE 802.11g: OFDM(64-QAM, 16-QAM, QPSK, BPSK)

IEEE 802.11n-HT20: OFDM(64-QAM, 16-QAM, QPSK, BPSK)

IEEE 802.11n-HT40: OFDM(64-QAM, 16-QAM, QPSK, BPSK)

Data Rate:

IEEE 802.11b: Up to 11 Mbps

IEEE 802.11g: Up to 54 Mbps

IEEE 802.11n-HT20: Up to MCS7

IEEE 802.11n-HT40: Up to MCS7

Number of Channels:

IEEE 802.11b: 11

IEEE 802.11g: 11

IEEE 802.11n-HT20: 11

IEEE 802.11n-HT40: 7

Channel Separation:

5 MHz

Antenna Type:

PCB Antenna

Antenna Gain: 3.05 dBi

Maximum Peak Power:

IEEE 802.11b: 18

1 dBm

IEEE 802.11g: 21±1 dBm

IEEE 802.11n-HT20: 16±1 dBm

IEEE 802.11n-HT40: 15±1 dBm

For 5 GHz U-NII Bands of Wi-Fi

Frequency Bands:

5150 MHz to 5250 MHz (U-NII-1)

5250 MHz to 5350 MHz (U-NII-2A)

5470 MHz to 5725 MHz (U-NII-2C)

5 725 MHz to 5 850 MHz (U-NII-3)

Frequency Ranges:

5180 MHz to 5240 MHz

5260 MHz to 5320 MHz

5500 MHz to 5700 MHz

5 745 MHz to 5 825 MHz

Support Standards:

IEEE 802.11a/n/ac

TPC Function: Not Support

DFS Operational mode:

Slave without radar Interference detection function

Type of Modulation:

IEEE 802.11a: OFDM(64QAM, 16QAM, QPSK, BPSK)

IEEE 802.11n: OFDM(64QAM, 16QAM, QPSK, BPSK)

IEEE 802.11ac: OFDM(256QAM, 64QAM, 16QAM, QPSK, BPSK)

Channel Spacing:

IEEE 802.11a/n-HT20/ac-VHT20: 20 MHz

IEEE 802.11n-HT40/ac-VHT40: 40 MHz

IEEE 802.11ac-VHT80: 80 MHz

Data Rate:

IEEE 802.11a: Up to 54 Mbps

IEEE 802.11n-HT20: Up to MCS15

IEEE 802.11n-HT40: Up to MCS15

IEEE 802.11ac-VHT20: Up to MCS8

IEEE 802.11ac-VHT40: Up to MCS9

IEEE 802.11ac-VHT80: Up to MCS9

Shenzhen KTC Commercial Display Technology CO.,LTD.

Number of Channels:

5150 MHz to 5250 MHz:

4 for IEEE 802.11a/n-HT20/ac-VHT20

2 for IEEE 802.11n-HT40)/ac-VHT40

1 for IEEE 802.11acVHT80

5250 MHz to 5350 MHz:

4 for IEEE 802.11a/n-HT20/ac-VHT20

2 for IEEE 802.11n-HT40)/ac-VHT40

1 for IEEE 802.11acVHT80

5470 MHz to 5725 MHz:

11 for IEEE 802.11a/n-HT20/ac-VHT20

5 for IEEE 802.11n-HT40/ac-VHT40

2 for IEEE 802.11ac-VHT80

5725 MHz to 5850 MHz:

5 for IEEE 802.11a/n-HT20/ac-VHT20

2 for IEEE 802.11n-HT40/ac-VHT40

1 for IEEE 802.11ac-VHT80

Antenna Type: PCB Antenna

Antenna Gain:

5150 MHz to 5250 MHz: 4.39 dBi

5250 MHz to 5350 MHz: 4.68 dBi

5470 MHz to 5725 MHz: 5.57 dBi

5725 MHz to 5850 MHz: 5.68 dBi

Maximum conducted

output power (dBm):

U-NII-1

U-NII-2A

U-NII-2C

U-NII-3

IEEE 802.11a: 13±1 13±1 13±1 11±1

IEEE 802.11n-HT20:

12±1 12±1 12±1 10±1

IEEE 802.11n-HT40:

IEEE 802.11ac-VHT20 12±1 12±1 12±1 10±1

IEEE 802.11ac-VHT40

IEEE 802.11ac-VHT80:

NOTICE:

◆please keep this product and accessories attached to the places which children can't touch;

◆do not splash water or other liquid onto this product, otherwise it may cause damage;

◆do not put this product near the heat source or direct sunlight, otherwise it may cause

deformation or malfunction;

◆please keep this product away from flammable or naked flame;

◆please do not repair this product by yourself. Only qualified personnel can be repaired.

FCC Statement

- List of applicable FCC rules

This device complies with FCC part 15C : 15.247&15.407

- Summarize the specific operational use conditions

This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. And the

module should be installed at a minimum distance of 20 cm away from person nearby. The host product manufacturer should state this

information to the host instruction manual.

Shenzhen KTC Commercial Display Technology CO.,LTD.

- Trace antenna designs

Not applicable.

- RF exposure considerations

This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be

co-located or operating in conjunction with any other antenna or transmitter. This modular must be installed and operated with a

minimum distance of 20 cm between the radiator and user body.

- Antennas

Antenna Type: PCB Antenna

Antenna Gain:

2.4G BT：2.5 dBi

2.4G WIFI：3.05 dBi

5.2G WIFI：4.39 dBi

5.3G WIFI：4.68 dBi

5.6G WIFI：5.57 dBi

5.8G WIFI：5.68 dBi

The antenna is permanently attached and not consideration of replacement.

- Label and compliance information

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into

which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the

following: “Contains Transmitter Module FCC ID: 2AQ5RWBL-8822BU1-A Or Contains FCC ID: 2AQ5RWBL-8822BU1-A”.

- Information on test modes and additional testing requirements

Any final host product with the modular transmitter installed should be under test according to guidance given in KDB 996369 D04. To

enter test mode for module, REALTEK 11ac 8822 BU USB WLAN NIC Mass production kit software and command is necessary. When

Shenzhen KTC Commercial Display Technology CO.,LTD.

something wrong happens in configuring test modes for host product with module, host product manufacturer should coordinate with

module manufacturer for technical support. It is recommended that some investigative measurements should be taken to confirm that

host product with module installed does not exceed the spurious emissions limits or band edge limits.

- Additional testing, Part 15 Subpart B disclaimer

The modular transmitter is only FCC authorized for the specific rule parts (FCC Part 15.247&15.407) list on the grant, and that the host

product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular

transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter

installed when contains digital circuity.

Canada Statement

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est

autorisée aux deux conditions suivantes :

(1) l’appareil ne doit pas produire de brouillage;

(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en

compromettre le fonctionnement.

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure,

users can obtain Canadian information on RF exposure and compliance.

Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 et la conformité à l'exposition de

RSS-102 rf, utilisateurs peut obtenir l'information canadienne sur l'exposition et la conformité de rf.

The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to

co-channel mobile satellite systems

Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire

les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;

Shenzhen BL-R8822BU1-A WIFI Module Manuel utilisateur

Marque: Shenzhen

Modèle: BL-R8822BU1-A WIFI Module

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Shenzhen BL-R8822BU1-A WIFI Module User manual

Shenzhen BL-R8822BU1-A WIFI Module Manuel utilisateur

Shenzhen BL-R8822BU1-A WIFI Module Manuel utilisateur

dans d''autres langues

Autres documents