KTC BL-R8812AFI-A Wi-Fi Module Manuel utilisateur

BL-R8812AFI-A Wi-Fi Module
Marque
KTC
Modèle
BL-R8812AFI-A Wi-Fi Module
Taper
Manuel utilisateur
Shenzhen KTC Commercial Display Technology CO.,LTD.
WIFI Module
Model Number: BL-R8812AF1-A
Product Descrition：
BL-R8822BU1-A module design is based on Realtek BL-R8812AF1-A solution, The BL-
R8812AF1-A is a highly integrated single chip which has built in a 2x2 dual-band wireless
LAN radio. The Module is a highly integrated MAC/BBP and 2.4/5GHz PA/LNA single
chip which supportsa 433.3Mbps PHY rate. The Module is designed to support standard-
based features in the areas of security, quality of service, and international regulations,
giving end users the greatestperformance anytime and in any circumstance. This
documentation describes the engineering requirements specification.
Product Specification
For 2.4 GHz ISM Band of Wi-Fi
Frequency Band: 2400 MHz to 2483.5 MHz
Frequency Range:
2412 MHz to 2472 MHz
Support Standards:
IEEE 802.11b, IEEE 802.11g, IEEE 802.11n-HT20, IEEE 802.11n-
HT40
Type of Modulation:
IEEE 802.11b: DSSS(CCK, DQPSK, DBPSK)
IEEE 802.11g: OFDM(64-QAM, 16-QAM, QPSK, BPSK)
IEEE 802.11n-HT20: OFDM(64-QAM, 16-QAM, QPSK, BPSK)
IEEE 802.11n-HT40: OFDM(64-QAM, 16-QAM, QPSK, BPSK)
Data Rate:
IEEE 802.11b: Up to 11 Mbps
IEEE 802.11g: Up to 54 Mbps
IEEE 802.11n-HT20: Up to MCS15
IEEE 802.11n-HT40: Up to MCS15
Number of Channels:
IEEE 802.11b: 13
IEEE 802.11g: 13
IEEE 802.11n-HT20: 13
IEEE 802.11n-HT40: 9
Channel Separation:
5 MHz
Antenna Type:
PCB Antenna
Antenna Gain:
5 dBi
Maximum Peak Power:
IEEE 802.11b: 20±2 dBm
IEEE 802.11g: 20±12dBm
IEEE 802.11n-HT20: 16.5±2 dBm
IEEE 802.11n-HT40: 16.5±2 dBm
For 5 GHz U-NII Bands of Wi-Fi
Frequency Bands:
5150 MHz to 5250 MHz (U-NII-1)
5250 MHz to 5350 MHz (U-NII-2A)
5470 MHz to 5725 MHz (U-NII-2C)
5 725 MHz to 5 850 MHz (U-NII-3)
Frequency Ranges:
5180 MHz to 5240 MHz
5260 MHz to 5320 MHz
5500 MHz to 5700 MHz
5 745 MHz to 5 825 MHz
Support Standards:
IEEE 802.11a/n/ac
TPC Function:
Not Support
DFS Operational mode:
Slave without radar Interference detection function
Shenzhen KTC Commercial Display Technology CO.,LTD.
Type of Modulation:
IEEE 802.11a: OFDM(64QAM, 16QAM, QPSK, BPSK)
IEEE 802.11n: OFDM(64QAM, 16QAM, QPSK, BPSK)
IEEE 802.11ac: OFDM(256QAM, 64QAM, 16QAM, QPSK, BPSK)
Channel Spacing:
IEEE 802.11a/n-HT20/ac-VHT20: 20 MHz
IEEE 802.11n-HT40/ac-VHT40: 40 MHz
IEEE 802.11ac-VHT80: 80 MHz
Data Rate:
IEEE 802.11a: Up to 54 Mbps
IEEE 802.11n-HT20: Up to MCS15
IEEE 802.11n-HT40: Up to MCS15
IEEE 802.11ac-VHT20: Up to MCS8
IEEE 802.11ac-VHT40: Up to MCS9
IEEE 802.11ac-VHT80: Up to MCS9
Number of Channels:
5150 MHz to 5250 MHz:
4 for IEEE 802.11a/n-HT20/ac-VHT20
2 for IEEE 802.11n-HT40)/ac-VHT40
1 for IEEE 802.11acVHT80
5250 MHz to 5350 MHz:
4 for IEEE 802.11a/n-HT20/ac-VHT20
2 for IEEE 802.11n-HT40)/ac-VHT40
1 for IEEE 802.11acVHT80
5470 MHz to 5725 MHz:
11 for IEEE 802.11a/n-HT20/ac-VHT20
5 for IEEE 802.11n-HT40/ac-VHT40
2 for IEEE 802.11ac-VHT80
5725 MHz to 5850 MHz:
5 for IEEE 802.11a/n-HT20/ac-VHT20
2 for IEEE 802.11n-HT40/ac-VHT40
1 for IEEE 802.11ac-VHT80
Antenna Type:
PCB Antenna
Antenna Gain:
5150 MHz to 5250 MHz: 5 dBi
5250 MHz to 5350 MHz: 5 dBi
5470 MHz to 5725 MHz: 5 dBi
5725 MHz to 5850 MHz: 5 dBi
Maximum conducted
output power (dBm):
U-NII-1
U-NII-2C
U-NII-3
IEEE 802.11a:
6
±
2
±
6
±
2
6
±
2
IEEE 802.11n-HT20:
6
±
2
±
5
±
2.5
2
±
2
IEEE 802.11n-HT40:
6
±
2
±
5
±
2.5
2
±
2
IEEE 802.11ac-VHT20
6
±
2
±
5
±
2.5
2
±
2
IEEE 802.11ac-VHT40
6
±
2
±
5
±
2.5
2
±
2
IEEE 802.11ac-VHT80:
6
±
2
±
5
±
2.5
2
±
2
2.4G WIFI-Operation Frequency Each of Channel
IEEE 802.11b,
IEEE 802.11g,
IEEE 802.11n-HT20
f = 2407 + 5k MHz, k = 1,…,13
IEEE 802.11n-HT40
f = 2407 + 5k MHz, k = 3,…,11
Note:
f is the operating frequency (MHz);
k is the operating channel.
5GWIFI-Operation Frequency Each of Channel
U-NII-1
U-NII-2A
U-NII-2C
U-NII-3
IEEE 802.11a,
IEEE 802.11n-HT20,
f = 5000 + 5k, k = 32 + 4n
f = 5000 + 5k,
k = 145 + 4n
Shenzhen KTC Commercial Display Technology CO.,LTD.
IEEE 802.11ac-VHT20
n = 1,…, 4
n = 5,…, 8
n = 17,…, 27
n = 1,…, 5
IEEE 802.11n-HT40,
IEEE 802.11ac-VHT40
f = 5000 + 5k, k = 30 + 8n
f = 5000 + 5k,
k = 143 + 8n
n = 1, 2
n = 1,…, 5
n = 9,…, 13
n = 1, 2
IEEE 802.11ac-VHT80
f = 5000 + 5k, k = 26 + 16n
f = 5000 + 5k,
k = 155
n = 1
n = 1, 2
n = 5, 6
Note:
f is the operating frequency (MHz);
k is the operating channel.
NOTICE:
◆please keep this product and accessories attached to the places which children can't touch;
◆do not splash water or other liquid onto this product, otherwise it may cause damage;
◆do not put this product near the heat source or direct sunlight,
otherwise it may cause
deformation or malfunction;
◆please keep this product away from flammable or naked flame;
◆please do not repair this product by yourself. Only qualified personnel can be repaired.
FCC Statement
- List of applicable FCC rules
This device complies with FCC part 15C : 15.247&15.407
- Summarize the specific operational use conditions
This device and its antenna(s) must not be co-located or operating in
conjunction with any other antenna or transmitter. And the module
should be installed at a minimum distance of 20 cm away from person
nearby. The host product manufacturer should state this information to
the host instruction manual.
- Trace antenna designs
Not applicable.
- RF exposure considerations
This modular complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter. This modular must be installed and
operated with a minimum distance of 20 cm between the radiator and user body.
- Antennas
- AntennaType: PCB Antenna
Antenna Gain:
2.4G WIFI：5.0 dBi
5.2G WIFI：5.0 dBi
5.2G WIFI：5.0 dBi
5.6G WIFI：5.0 dBi
5.8G WIFI：5.0 dBi
The antenna is permanently attached and not consideration of replacement.
Shenzhen KTC Commercial Display Technology CO.,LTD.
- Label and compliance information
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Caution: The user is cautioned that changes or modifications not expressly approved
by the party responsible for compliance could void the user's authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
If the FCC identification number is not visible when the module is installed inside another
device, then the outside of the device into which the module is installed must also
display a label referring to the enclosed module. This exterior label can use wording such
as the following: “Contains Transmitter Module FCC ID: 2AQ5RWBL-8812AF1-A Or
Contains FCC ID: 2AQ5RWBL-8812AF1-A”.
- Information on test modes and additional testing requirements
Any final host product with the modular transmitter installed should be under test
according to guidance given in KDB 996369 D04. To
enter test mode for module, REALTEK 11ac 8822 BU USB WLAN NIC Mass production kit
software and command is necessary. When
something wrong happens in configuring test modes for host product with module, host
product manufacturer should coordinate with module manufacturer for technical support.
It is recommended that some investigative measurements should be taken to confirm
that host product with module installed does not exceed the spurious emissions limits or
band edge limits.
Additional testing, Part 15 Subpart B disclaimer
The modular transmitter is only FCC authorized for the specific rule parts (FCC Part
15.247&15.407) list on the grant, and that the host product manufacturer is responsible
Shenzhen KTC Commercial Display Technology CO.,LTD.
for compliance to any other FCC rules that apply to the host not covered by the
modular transmitter grant of certification. The final host product still requires Part 15
Subpart B compliance testing with the modular transmitter installed when contains digital
circuity.
Canada Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is
subject to the following two conditions:
(1) This device may not cause
interference; and
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire
de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d’en compromettre le fonctionnement.
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS
102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on
RF exposure and compliance.
Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5
de RSS 102 et la conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir
l'information canadienne sur l'exposition et la conformité de rf.
The device for operation in the band 5150-5250 MHz is only for indoor use to
reduce the potential for harmful interference to co-channel mobile satellite
systems
Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement
pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux
systèmes de satellites mobiles utilisant les mêmes canaux;
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

KTC BL-R8812AFI-A Wi-Fi Module Manuel utilisateur

BL-R8812AFI-A Wi-Fi Module
Marque
KTC
Modèle
BL-R8812AFI-A Wi-Fi Module
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Autres documents