HID iClass SE Le manuel du propriétaire

Taper
Le manuel du propriétaire
HID® iCLASS® SE Connectivity Module
Install Guide Addendum
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference; (2) This device must accept any interference received,
including interference that may cause undesired operation.
ISED
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference; (2) This device must accept any interference, including
interference that may cause undesired operation of the device.
Operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to
co-channel mobile satellite systems.
Le présent appareil est conforme aux CNR d’ISDE Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de
brouillage, et (2) l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
La bande 51505250 MHz est réservée uniquement pour une utilisation à l’intérieur afin de réduire les risques
de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.
RF EXPOSURE CONSIDERATIONS
FCC
This module complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This
transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. RF
Exposure - At least 20 cm of separation distance between the module and the user's body must be maintained
at all times.
ISED
This device meets the IC requirements for RF exposure in public or uncontrolled environments.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. RF
Exposure - At least 20 cm of separation distance between the module and the user's body must be maintained
at all times.
INSTRUCTION TO MODULE INTEGRATOR
LABELING
A label must be affixed to the outside of final commercial product with the following statements:
Contains FCC ID: JQ6-SECONNECT
Contains IC: 2236B-SECONNECT
ANTENNA
The antenna gain of a new antenna should be of the same type as the originally approved antenna and the
antenna gain should not be higher than the antenna gain of the originally tested antenna. The list of originally
approved PCB antennas is the following:
BLE - Type of antenna: chip SMD; WURTH P/N: 7488930245; peak gain: 0.5 dBi
Wi-Fi - Type of antenna: chip SMD; AVX P/N: M830520; peak gain: 1.0 dBi (2.4 GHz); 2.6 dBi (5 GHz)
FCC RF EXPOSURE CONSIDERATIONS
Consistent with §2.909(a), the following text must be included within the user’s manual or operator instruction
guide for the final commercial product:
This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This
transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This device is only authorized for use in a mobile application. At least 20 cm of separation distance between
the module and the user's body must be maintained at all times.
ADDITIONAL TESTING, PART 15 SUBPART B DISCLAIMER
The final host / module combination may also need to be evaluated against the FCC Part 15B criteria for
unintentional radiators in order to be properly authorized for operation as a Part 15 digital device. The FCC
Part 15 Statement shall be included in the user manual of final commercial product if applicable.
CAUTION STATEMENT FOR MODIFICATIONS:
CAUTION: Any changes or modifications not expressly approved could void the user’s authority to operate the
equipment.
  • Page 1 1
  • Page 2 2

HID iClass SE Le manuel du propriétaire

Taper
Le manuel du propriétaire

dans d''autres langues