GSD WXT5BM2511 Le manuel du propriétaire

WXT5BM2511
Marque
GSD
Modèle
WXT5BM2511
Taper
Le manuel du propriétaire
Hui Zhou Gaoshengda Technology Co., LTD WXT5BM2511
PAGE 1 OF 5
Version 1.0
WIFI+BT Module
IEEE 802.11 a/b/g/n/ac/ax 2T/2R
Model Number: WXT5BM2511
Product Descrition
The WXT5BM2511 is a complete 2.4GHz/5GHz WIFI 2×2 MIMO module. This module provides a high level of
integration with a dual-stream IEEE 802.11ax MAC/ base band /radio and Bluetooth 5.2.The WLAN operation
supports 20MHz,40MHz and 80MHz channels for data rates up to 1201Mbps. It fully complies with IEEE 802.11
a/b/g/n/ac/ax feature rich wireless connectivity at high standards,delivers reliable,cost-effective, throughput from
an extended distance.
Product Features
Product Specification
Model
WXT5BM2511
Product Name
WIF+BT Module
Standard
802.11 a/b/g/n/ac/ax
Interface
USB
Data Transfer Rate
1,2,5.5,6,11,12,18,22,24,30,36,48,54,60,90,120 and maximum of 1201Mbps
Modulation Method
GFSK,π/4-DQPSK,8DPSK(bluetooth)
DQPSK,DBPSK,CCK(802.11b)
QPSK,BPSK,16QAM,64QAM with OFDM (802.11g)
QPSK,BPSK,16QAM,64QAM with OFDM (802.11n)
QPSK,BPSK,16QAM,64QAM with OFDM (802.11a)
QPSK,BPSK,16QAM,64QAM,256QAM with OFDM (802.11ac)
QPSK,BPSK,16QAM,64QAM,256QAM,1024QAM with OFDMA (802.11ax)
Frequency Band
BLUETOOTH
2402~2480 MHz
WIFI
2.4G: 2412~2462 MHz
5G: 5180 MHz to 5240 MHz(U-NII-1)
5260 MHz to 5320 MHz(U-NII-2A)
5500 MHz to 5720 MHz(U-NII-2C)
5 745 MHz to 5 825 MHz(U-NII-3)
Operation Mode
Infrastructure
Security
WEP, TKIP, AES, WPA, WPA2
Operating Voltage
5V±10%
Current Consumption
＜1000mA
Antenna Type
PCB
Operating
Temperature
-10 ~ 70°C ambient temperature
Storage Temperature
-40 ~ 80°C ambient temperature
Humidity
5 to 95 % maximum (non-condensing)
◆ Complies with IEEE 802.11b/g/n/ax for 2.4GHz，IEEE 802.11a/n/ac/ax for 5GHz
◆ Bluetooth v5.2
◆ Two transmit and Two receive path(2T2R)
◆ Works with all existing network nfrastructure.
◆ Capable of up to 128-Bit WEP Encryption.
◆ Freedom to roam while staying connected.
◆ UP to 1201 Mbps High-Speed Transfer Rate in 802.11ax mode of operation.
◆ Operating Systems：Linux, Win10, Win11.
◆ Low power consumption.
◆ Easy to install and configure.
◆ High speed usd 2.0/3.0 interface.
◆ROHS compliant
Hui Zhou Gaoshengda Technology Co., LTD WXT5BM2511
PAGE 2 OF 5
Version 1.0
NOTICE:
◆please keep this product and accessories attached to the places which children can't touch;
◆do not splash water or other liquid onto this product, otherwise it may cause damage;
◆do not put this product near the heat source or direct sunlight, otherwise it may cause
deformation or malfunction;
◆please keep this product away from flammable or naked flame;
◆please do not repair this product by yourself. Only qualified personnel can be repaired.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
2.2
This module has been assessed against the following FCC rule parts: CFR 47 FCC Part 15 C (15.247, DTS and DSS) and
CFR 47 FCC Part 15 E (NII). It is applicable to the modular transmitter
2.3
This radio transmitter 2AC23-WXT5B has been approved by Federal Communications Commission to operate with the
antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a
gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
The concrete contents to check are the following three points.
１) Must use a PCB antenna with gain not exceeding those shown in the table below.
２) Should be installed so that the end user cannot modify the antenna
３) Feed line should be designed in 50ohm
Fine-tuning of return loss etc. can be performed using a matching network.
The antenna shall not be accessible for modification or change by the end user
2.4
The module complies with FCC Part 15.247 / Part 15.407 and apply for Single module approval.
2.5
Trace antenna designs: Not applicable.
The device must be professionally installed
The intended use is generally not for the general public. It is generally for industry/commercial use.
The connector is within the transmitter enclosure and can only be accessed by disassembly of the transmitter which is not
normally required. the user has no access to the connector.
Installation must be controlled. Installation requires special training
Hui Zhou Gaoshengda Technology Co., LTD WXT5BM2511
PAGE 3 OF 5
Version 1.0
2.6
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must
not be co-located or operating in conjunction with any other antenna or transmitter.
2.7
Antenna type and antenna gain:
2.4G WIFI&5G WIFI Antennas:
Antenna
Antenna Type
MAX Antenna Gain (dBi)
0
PCB Antenna
1.55
1
PCB Antenna
1.78
Antenna No.
Frequency Band
Antenna Type
Max Antenna Gain (dBi)
0
5150-5850
PCB Antenna
4.46
1
5150-5850
PCB Antenna
3.18
BT Antenna:
Antenna
Frequency (MHz)
Antenna Type
MAX Antenna Gain (dBi)
1
2402-2480
PCB Antenna
0.9
2.8
Please notice that if the FCC identification number is not visible when the module is installed inside another device, then
the outside of the device into which the module is installed must also display a label referring to the enclosed module. This
exterior label can use wording such as “Contains FCC ID: 2AC23-WXT5B”; any similar wording that expresses the same
meaning may be used.
Canada Statement
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
Please notice that if the ISED certification number is not visible when the module is installed inside another device, then
the outside of the device into which the module is installed must also display a label referring to the enclosed module. This
exterior label can use wording such as the following: “Contains IC: 12290A-WXT5B” any similar wording that expresses
the same meaning may be used.
l'appareil hôte doit porter une étiquette donnant le numéro de certification du module d'Industrie Canada, précédé des mots
« Contient un module d'émission », du mot « IC: 12290A-WXT5B» ou d'une formulation similaire exprimant le même sens,
comme suit
The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference
to co-channel mobile satellite systems
for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall
be such that the equipment still complies with the e.i.r.p. limits as appropriate;
Hui Zhou Gaoshengda Technology Co., LTD WXT5BM2511
PAGE 4 OF 5
Version 1.0
Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin
de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
pour les dispositifs munis d'antennes amovibles, le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de
5 725 à 5 850 MHz) doit être conforme à la limite de la p.i.r.e. spécifiée, selon le cas;
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and
compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and
compliance.
Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 etla conformité à
l'exposition de RSS-102 RF, utilisateurs peut obtenir l'information canadienne surl'exposition et la conformité de rf.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter. This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body.
Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenne ouémetteur. Cet
équipement devrait être installé et actionné avec une distance minimum de 20 centimètres entre le radiateur et votre corps.
This radio transmitter 12290A-WXT5B has been approved by Innovation, Science and Economic
Development Canada to operate with the antenna types listed below, with the maximum permissible
gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain
Le présent émetteur radio 12290A-WXT5B a été approuvé par Innovation, Sciences et Développement
économique Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain
admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au
gain maximal indiqué pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de
l'émetteur.
The concrete contents to check are the following three points.
１) Must use a PCB antenna with gain not exceeding those shown in the table below.
２) Should be installed so that the end user cannot modify the antenna
３) Feed line should be designed in 50ohm
Fine tuning of return loss etc. can be performed using a matching network.
Le contenu concret à vérifier sont les trois points suivants.
1) doit utiliser une antenne PCB avec un gain ne dépassant pas ceux indiqués dans le tableau ci-dessous.
2) devrait être installé de sorte que l’utilisateur ne puisse pas modifier l’antenne
3) la ligne d’alimentation devrait être conçue dans 50ohm
Le réglage fin de la perte de retour, etc. peut être effectué en utilisant un réseau correspondant.
Antenna type and antenna gain:
2.4G WIFI&5G WIFI Antennas:
Antenna
Antenna Type
MAX Antenna Gain (dBi)
0
PCB Antenna
1.55
1
PCB Antenna
1.78
Antenna No.
Frequency Band
Antenna Type
Max Antenna Gain (dBi)
0
5150-5850
PCB Antenna
4.46
1
5150-5850
PCB Antenna
3.18
BT Antenna:
Antenna
Frequency (MHz)
Antenna Type
MAX Antenna Gain (dBi)
1
2402-2480
PCB Antenna
0.9
Hui Zhou Gaoshengda Technology Co., LTD WXT5BM2511
PAGE 5 OF 5
Version 1.0
Notice to OEM integrator
Must use the device only in host devices that meet the FCC/ISED RF exposure category of mobile, which means the device
is installed and used at distances of at least 20cm from persons.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements related to the transmitter as show
in this manual(FCC/Canada statement).
Host manufacturer is responsible for compliance of the host system with module installed with all other applicable
requirements for the system such as Part 15 B, ICES 003.
Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when
the module is installed in the host.
The use condition limitations extend to professional users, then instructions must state that this information also extends to
the host manufacturer’s instruction manual.
This module is stand-alone modular. If the end product will involve Multiple simultaneously transmitting condition or
different operational conditions for a stand-alone modular transmitter in a host, host manufacturer has to consult with
module manufacturer for the installation method in the end system.
Any company of the host device which install this modular should perform the test of radiated &
condicted emission and spurious emission etc. according to FCC Part 15C: 15.247 and 15.209 &
15.207, 15.407, 15B class B requirement, only if the test result comply with FCC part 15C: 15.247 and
15.209 & 15.207, 15.407,15B class B requirement. Then the host can be sold legally.
This modular transmitter is only FCC authorized for the specific rule parts ( 47CFR Part 15.247
and 15.407) listed on the grant, and that the host product manufacturer is responsible for
compliance to any other FCC rules that apply to the host not covered by the modular transmitter
grant of certification.
Host manufacturer is strongly recommended to confirm compliance with FCC/ISED
requirements for the transmitter when the module is installed in the host.
Must have on the host device a label showing Contains FCC ID: 2AC23-WXT5B or IC: 12290A-WXT5B
Both FCC ID and IC ID are not to be placed on the host at the same time and only hosts going into the US can use the FCC
ID and only hosts going into Canada can use the IC ID.
Installer should put it in the manual：
The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful
interference to co-channel mobile satellite systems
l'hôte doit utiliser l'instrument uniquement dans des dispositifs qui répondent à la fcc / (catégorie d'exposition rf mobile, ce
qui signifie le dispositif est installé et utilisé à une distance d'au moins 20 cm de personnes.
le manuel de l'utilisateur final doit inclure la partie 15 / (fac rss gen déclarations de conformité relatives à l'émetteur que de
montrer dans ce manuel.
le fabricant est responsable de la conformité de l'hôte, le système d'accueil avec le module installé avec toutes les autres
exigences applicables du système comme la partie 15 b, ices - 003.
accueillir le fabricant est fortement recommandé de confirmer la conformité avec les exigences de la fcc / (émetteur lorsque
le module est installé dans l'hôte.
le dispositif d'accueil doivent avoir une étiquette indiquant contient FCC ID: 2AC23-WXT5B，IC: 12290A-WXT5B
Les personnes chargées de l'installation devraient figurer dans le manuel:
Les dispositifs fonctionnant dans la bande de 5 150 à 5 250 MHz sont réservés uniquement pour une utilisation à l’intérieur
afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.
Doit avoir sur l'appareil hôte une étiquette indiquant Contient l'ID FCC : 2AC23-WXT5B ou IC : 12290A-WXT5B L'ID
FCC et l'ID IC ne doivent pas être placés sur l'hôte en même temps et seuls les hôtes se rendant aux États-Unis peuvent
utiliser l'ID FCC et seuls les hôtes se rendant au Canada peuvent utiliser l'ID IC.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

GSD WXT5BM2511 Le manuel du propriétaire

WXT5BM2511
Marque
GSD
Modèle
WXT5BM2511
Taper
Le manuel du propriétaire
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents