LEGAL STATEMENT
FCC STATEMENT:
This device complies with Part 15 of the FCC Rules. Operation issubject to the following two conditions: (1) this device may not
causeharmful interference, and (2) this device must accept any interferencereceived, including interference that may cause
undesired operation.
changes or modifications not expressly approved by the party responsible for compliance could void the users authority to
operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Please notice that if the FCC identification number is not visible when the module is installed inside another device, then the
outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior
label can use wording such as the following: Contains FCC ID: any similar wording that expresses the same
meaning may be used.
This device contains license exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development
Canada s license exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
L' metteur/r cepteur exempt de licencecontenu dans le pr sent appareilestconforme aux
CNR d'Innovation, Sciences et D veloppement conomique Canada applicables aux appareils radio exempts de licence.
L'exploitationestautoris e aux deux conditions suivantes :
1)L'appareil ne doit pas produire de brouillage;
2)L'appareil doit accepter tout brouillage radio lectriquesubi, m me si le brouillageest susceptible d'encompromettre le
fonctionnement.
Please notice that if the I identification number is not visible when the module is installed inside another device, then the
outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior
label can use wording such as the following: Contains IC: any similar wording that expresses the same
meaning may be used.
Notez que si le numérod'identification I n'est pas visible lorsque le module estinstallé dans un autreappareil,
uneétiquetteindiquant le module attaché doit égalementêtreaffichée à l'extérieur de l'appareiloù le module estinstallé.
L'étiquetteextérieurepeutêtrelibelléecomme suit: « contient IC: » toute expression similaire qui exprime le
mêmesens.
The device must be professionally installed The intended use is generally not for the general public.It is generally for industry/
commercial use.The connector is within the transmitter enclosure and can only be accessed by disassembly of the transmitter
that is not normally required. the user has no access to the connector. Installation must be controlled. Installation requires
special training This module has been assessed against the following FCC rule parts: CFR 47 FCC Part 15 C (15.247, DTS). It is
applicable to the modular transmitter
This radio transmitter FCC ID:2AJ5SEM00556 has been approved by Federal Communications Commission to
operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this
list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this
device. The concrete contents to check are the following three points.
Must use antenna such as with gain not exceeding dBi;
Should be installed so that the end user cannot modify the antenna;
Feed line should be designed in 50ohm
Fine tuning of return loss etc. can be performed using a matching network.
L'émetteur radio FCC ID:2AJ5SEM00556 a étéapprouvé par la FCC
Utilisez les types d'antennesénumérés ci dessous et indiquez le gain maximal admissible. Le gain du type d'antenne non inclus
dans cettelisteestsupérieur au gain maximal de l'un des types énumérés et ne doit pas êtreutilisé avec cetéquipement.
Le contenuspécifique de l'inspectioncomprend les trois points suivants.
Une antennedont le gain ne d passe pas dbi, telle que , doit tre
utilis e;
Doit tre install l o l'utilisateur final ne peut pas modifier l'antenne;
La ligned'alimentation doit treconçue pour 50 ohms
Le réseaucorrespondantpeutêtreutilisé pour affiner la perte de retour, etc.
Antennas:
Must use the device only in host devices that meet the FCC/ISED RF exposure category of . This transmitter must not
be co located or operating in conjunction with any other antenna or transmitter.
The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements related to the transmitter as show in this
manual(FCC/IC Canada statement). Host manufacturer is responsible for compliance of the host system with module installed
with all other applicable requirements for the system such as Part 15 B, ICES 003. Host manufacturer is strongly
recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the
host.
Must have on the host device a label showing Contains FCC ID:2AJ5SEM00556 IC: 22061 EM00556
The use condition limitations extend to professional users, then instructions must state that this information also extends to
the host manufacturers instruction manual.
This module is stand alone modular. If the end product will involve the Multiple simultaneously transmitting condition or
different operational conditions for a stand alone modular transmitter in a host, host manufacturer have to consult with
module manufacturer for the installation method in end system. Any company of the host device which install this modular
should perform the test of radiated &
condicted emission and spurious emission etc. according to FCC Part 15C: 15.247 and 15.209 &
15.207, 15B class B requirement, only if the test result comply with FCC part 15C: 15.247 and
15.209 & 15.207, 15B class B requirement. Then the host can be sold legally.
This modular transmitter is only FCC authorized for the specific rule parts ( 47CFR Part 15.247) listed on the grant, and that the
host product manufacturer is responsible for
compliance to any other FCC rules that apply to the host not covered by the modular transmitter
grant of certification. Host manufacturer is strongly recommended to confirm compliance with FCC/ISED
requirements for the transmitter when the module is installed in the host.
Must have on the host device a label showing Contains FCC ID: 2AJ5SEM00556 and
Contains IC: 22061 EM00556
l'hôte doit utiliserl'instrumentuniquement dans des dispositifs qui r pondent la fcc / (cat goried'exposition rf . le
manuel de l'utilisateur final doit inclure
la partie 15 / (fac rss gen d clarations de conformit relatives l' metteur que de montrer dans cemanuel. le fabricant
estresponsable de la conformit de l'hôte, le syst me d'accueil avec le module install avec toutes les autres exigences
applicables du syst me comme la partie 15 b, ices 003. accueillir le fabricant estfortementrecommand de confirmer la
conformit avec les exigences de la fcc / ( metteurlorsque le module est install dans l'hôte. le
dispositifd'accueildoiventavoirune tiquetteindiquantcontient FCC ID:2AJ5SEM00556 IC: 22061 EM00556
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
dans d''autres langues
- English: ebyte E01C-ML01S User manual
Autres documents
-
GSD WXT2AM2101 WIFI+BT Module IEEE Manuel utilisateur
-
Murata LBEE5PK2BC Manuel utilisateur
-
GSD W37 Manuel utilisateur
-
GSD WC0PR1601 Le manuel du propriétaire
-
GSD WC5F Manuel utilisateur
-
GSD WXT5BM2511 Le manuel du propriétaire
-
GSD WC5EM2601F Dual Band WiFi Module Manuel utilisateur
-
Hui Zhou Gaoshengda Technology WT5YM2511 Wi-Fi+BT Module Mode d'emploi
-
ZIGBEE MG21 SoC Module JASMG21A Manuel utilisateur
-
GSD DT3AR1501 Manuel utilisateur
