P.1

Zigbee SoC

P.2

efficient, multi-protocol wireless SoC with a proven RF/antenna design and

industry leading wireless software stacks.

2. Product Feature

• 32-bit ARM® Cortex M33 core with 80MHz maximum operating

frequency

• Peripheral Reflex System enabling autonomous interaction of MCU

peripherals

• 2.4 GHz IEEE 802.15.4

• MCU Features overview

– 12-bit 1 Msps SAR Analog to Digital Converter (ADC)

– 2 × Analog Comparator (ACMP)

– 8 Channel DMA Controller

– 2 × 16-bit Timer/Counter

– 3 Compare/Capture/PWM channels

– 1 × 32-bit Timer/Counter

– 2 × I2C interface with SMBus support

• Supported Protocols

– Zigbee

P.3

• Lighting

• Health and Wellness

• Metering

• Building Automation and Security

NOTICE:

◆ please keep this product and accessories attached to the places which

◆ do not splash water or other liquid onto this product, otherwise it may

P.4

residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

This equipment complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions:

(1) This device may not cause harmful interference, and (2) This device must

Please notice that if the FCC identification number is not visible when the

module is installed inside another device, then the outside of the device into

which the module is installed must also display a label referring to the

enclosed module. This exterior label can use wording such as the following:

“Contains Transmitter Module FCC ID: U2ZJASMG21A”, or

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated

with a minimum distance of 20cm between the radiator & your body. This

P.5

including portable configurations with respect to Part 2.1093 and difference

antenna configurations.

There is requirement that the grantee provide guidance to the host

manufacturer for compliance with Part 15B requirements.

The module complies with FCC Part 15.247 and apply for Single module

approval.

Trace antenna designs: Not applicable.

This radio transmitter FCC ID: U2ZJASMG21A has been approved by

listed below, with the maximum permissible gain indicated.

Antenna types not included in this list that have a gain greater than the

maximum gain indicated for any type listed are strictly prohibited for use with

this device.

3. Feed line should be designed in 50ohm

Fine tuning of return loss etc. can be performed using a matching network.

P.6

any interference, including interference that may cause undesired operation

of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables

aux appareils radio exempts de licence. L’exploitation est autorisée aux deux

conditions suivantes:

(1) l’appareil ne doit pas produire de brouillage;

(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d’en compromettre le fonctionnement.

This transmitter must not be co-located or operating in conjunction with any

operated with a minimum distance of 20 centimeters between the radiator

and your body.

Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps

qu'aucune autre antenne ouémetteur.Cet équipement devrait être installé et

Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la

section 2.5 de RSS 102 etla conformité à l'exposition de RSS-102 rf,

utilisateurs peut obtenir l'information Canadienne surl'exposition et la

conformité de rf.

which the module is installed must also display a label referring to the

enclosed module. This exterior label can use wording such as the following:

“Contains Transmitter Module IC: 6924A-JASMG21A”, or

“Contains IC: 6924A-JASMG21A” any similar wording that expresses the

P.7

This radio transmitter [IC: 6924A-JASMG21A] has been approved by

Innovation, Science and Economic Development Canada to operate with the

antenna types listed below, with the maximum permissible gain indicated.

Antenna types not included in this list that have a gain greater than the

maximum gain indicated for any type listed are strictly prohibited for use with

this device.

The concrete contents to check are the following three points.

1. Must use antenna such as Chip antenna with gain not exceeding 2 dBi;

2. Should be installed so that the end user cannot modify the antenna;

3. Feed line should be designed in 50ohm

Fine tuning of return loss etc. can be performed using a matching network.

Le présent émetteur radio [IC: 6924A-JASMG21A] a été approuvé par

Innovation, Sciences et Développement économique Canada pour

fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain

admissible maximal. Les types d'antenne non inclus dans cette liste, et dont

le gain est supérieur au gain maximal indiqué pour tout type figurant sur la

1. doit utiliser une antenne comme Antenne à puce avec pifa gain n'excé

2. doivent être installés de façon que l'utilisateur final ne peut pas modifier

3. La ligne d’alimentation doit être conçue en 50ohm

Le réseau correspondant peut être utilisé pour affiner la perte de retour, etc.

P.8

The end user manual shall include FCC Part 15 /ISED RSS GEN compliance

statements related to the transmitter as show in this manual (FCC/Canada

statement). Host manufacturer is responsible for compliance of the host

system with module installed with all other applicable requirements for the

system such as Part 15 B, ICES 003. Host manufacturer is strongly

recommended to confirm compliance with FCC/ISED requirements for the

transmitter when the module is installed in the host.

Must have on the host device a label showing

“Contains Transmitter Module FCC ID: U2ZJASMG21A” or

“Contains Transmitter Module IC: 6924A-JASMG21A” or

“Contains IC: 6924A-JASMG21A”.

The use condition limitations extend to professional users, then instructions

must state that this information also extends to the host manufacturer’s

instruction manual.

perform the test of radiated & conducted emission and spurious emission

etc. according to FCC Part 15C: 15.247 and 15.209 &15.207, 15B class B

requirement, only if the test result comply with FCC part 15C: 15.247

and15.209 & 15.207, 15B class B requirement. Then the host can be sold

legally.

manufacturer is responsible for compliance to any other FCC rules that apply

to the host not covered by the modular transmitter grant of certification. Host

manufacturer is strongly recommended to confirm compliance with

FCC/ISED requirements for the transmitter when the module is installed in

P.9

à la fcc / (catégorie d'exposition rf mobile, ce qui signifie le dispositif est

installé et utilisé à une distance d'au moins 20 cm de personnes. Le manuel

de l'utilisateur final doit inclure la partie 15 / (fac rss gen déclarations de

conformité relatives à l'émetteur que de montrer dans ce manuel. le fabricant

est responsable de la conformité de l'hôte, le système d'accueil avec le

module installé avec toutes les autres exigences applicables du système

comme la partie 15 b, ices-003. accueillir le fabricant est fortement

recommandé de confirmer la conformité avec les exigences de la fcc /

(émetteur lorsque le module est installé dans l'hôte. le dispositif d'accueil

doivent avoir une étiquette indiquant contient FCC ID: U2ZJASMG21A, IC:

6924A-JASMG21A.