This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of

the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

The module is limited to OEM installation ONLY.

The OEM integrator is responsible for ensuring that the end-user has no manual instruction to remove or install

module.

2.6

include FCC compliance statements related to the transmitter or labeling requirements.If RF exposure statements and

use conditions are not provided, then the host product manufacturer is required to take responsibility of the module

through a change in FCC ID (new application).

A separate approval is required for all other operating configurations, including portable configurations with respect to

Part 2.1093 and difference antenna configurations.

host product manufacturer must notify the module grantee that they wish to change the antenna trace design. In this

case, a Class II permissive change application is required to be filed by the grantee, or the host manufacturer can

take responsibility through the change in FCC ID (new application) procedure followed by a Class II permissive

change application.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with a minimum distance of 20cm

between the radiator & your body. This transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter.

this device is permitted in large aircraft while flying above 10,000 feet.

device.

interference to co-channel mobile satellite systems

Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur

afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with

RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.

Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 etla conformité

Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenne ouémetteur. Cet

équipement devrait être installé et actionné avec une distance minimum de 20 centimètres entre le radiateur et votre

corps.

This radio transmitter IC : 12290A-WXT2F has been approved by FCC and by Innovation, Science and Economic

Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are

1.Antenna type is a PIFA with no more than 3.1 dBi gain at 2.4 GHz, 4.17 dBi gain at 5GHz and 4.7 dBi at 6GHz.

2.Should be installed so that the end user cannot modify the antenna

Fine tuning of return loss etc. can be performed using a matching network.

The antenna shall not be accessible for modification or change by the end user.

Le contenu concret à vérifier sont les trois points suivants.

Le réglage précis de la perte de rendement, etc. peut être effectué en utilisant un réseau correspondant.

Antennas:

Must use the device only in host devices that meet the FCC/ISED RF exposure category of mobile, which means the

device is installed and used at distances of at least 20 cm from persons.

and spurious emission etc. according to FCC Part 15C: 15.247 and 15.209 & 15.207, 15B class B requirement, only if

the test result comply with FCC part 15C: 15.247 and 15.209 & 15.207, 15B class B requirement. Then the host can

be sold legally.

The host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not

covered by the modular transmitter grant of certification. If the grantee markets their product as being Part 15 Subpart

B compliant (when it also contains unintentional-radiator digital circuity), then the grantee shall provide a notice

stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter

installed.

2.9

Testing of the host product with all the transmitters installed – referred to as the composite investigation test- is

investigated with all the transmitters in the final host product functioning to determine that no emissions exceed the

modes or settings. It is recommended that the host product manufacturer, installing the modular transmitter, perform

some investigative measurements to confirm that the resulting composite system does not exceed the spurious

emissions limits or band edge limits (e.g., where a different antenna may be causing additional emissions).

The testing should check for emissions that may occur due to the intermixing of emissions with the other transmitters,

digital circuitry, or due to physical properties of the host product (enclosure). This investigation is especially important

when integrating multiple modular transmitters where the certification is based on testing each of them in a

This modular transmitter is only FCC authorized for the specific rule parts ( 47CFR Part 15.247

and 15.407) listed on the grant, and that the host product manufacturer is responsible for

compliance to any other FCC rules that apply to the host not covered by the modular transmitter

with module manufacturer for the installation method in end system.

Please notice that if the FCC identification number is not visible when the module is installed inside the host device,

then the outside of the device into which the module is installed must also display a label referring to the enclosed

module. This exterior label shall use the wording: Contains FCC ID: 2AC23-WXT2F

Please notice that if the ISED Canada certification number is not visible when the module is installed inside the host

device device, then the outside of the device into which the module is installed must also display a label referring to

the enclosed module. This exterior label c hall use the wording: Contains IC: 12290A-WXT2F

This equipment complies with FCC and ISED-Canada radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed in host systems that are installed and operated with a minimum

distance of 20cm between the radiator & people. This transmitter must not be co-located or operating in conjunction

with any other antenna or transmitter except as permitted by FCC and ISED-Canada multie-transmitetr rules.

For a normal application, for example, A television, host systems that are installed and operated with a minimum

distance of 20cm between the radiator & people.

If the end-user really needed to install in host systems that are installed and operated with a distance less than 20cm

between the radiator & people, for example, a cell phone or laptop, the host systems need to comply with the

requirements in KDB 996369 D03 OEM Manual v01 and KDB 996369 D04 Module Integration Guide v02.

The module is not intended for general public, it must be professionally installed.

The typical application for the module:

Television

Monitor

For other devices,A especial driver was need to be installed to the host before start normal use for the module, and it

is different for difference kind of host.

Here is a general guide to determine RF exposure compliance: