SMK GT3FSCI02 Manuel utilisateur

GT3FSCI02
Marque
SMK
Modèle
GT3FSCI02
Taper
Manuel utilisateur
㻞㻜㻝㻥㻛㻜㻤㻛㻟㻜㻌
User Manual
㻌
㻌
Since this module is not sold to general end users directly, there is no user manual of module.
For the details about this module, please refer to the specification sheet of module.
This module should be installed in the host device according to the interface specification (installation
procedure).
This device complies with below part 15 of the FCC Rules.
Part 15 Subpart C
The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC
transmitter rules) listed on the grant, and the host product manufacturer is responsible
for compliance to any other FCC rules that apply to the host not covered by modular
transmitter grant of certification.
The final host product still requires Part 15 Subpart B compliance testing with the
modular transmitter installed.
The following information must be indicated on the host device of this module;
㻌
[for FCC]
Contains Transmitter Module FCC ID: GT3FSCI02
or
Contains FCC ID: GT3FSCI02
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
*If it is difficult to describe this statement on the host device due to the size, please describe in the user's
manual and also either describe on the device packaging or on a removable label attached to the device.
㻌
[for ISED(IC)]
Contains IC: 3683A-SCI02
The following statements must be described on the user manual of the host device of this module;
[for FCC]㻌
㻌
㻌
FCC CAUTION
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This transmitter must not be co-located or operated in conjunction with any other antenna or
transmitter.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF) Exposure Guidelines as this equipment
has very low levels of RF energy.
㻌
[for ISED(IC)]㻌
㻌
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to
the following two conditions:
1.This device may not cause interference.
2.This device must accept any interference, including interference that may cause undesired
operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux
CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
1.L’appareil ne doit pas produire de brouillage;
2.L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled
environment and meets RSS-102 of the ISED radio frequency (RF) Exposure rules as this
equipment has very low levels of RF energy.
Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un
environnement non contrôlé et respecte les règles d’exposition aux fréquences
radioélectriques (RF) CNR-102 de l’ISDE puisque cet appareil a une niveau tres bas d'energie
RF.
㻌
  • Page 1 1
  • Page 2 2

SMK GT3FSCI02 Manuel utilisateur

GT3FSCI02
Marque
SMK
Modèle
GT3FSCI02
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Autres documents