LITE ON NIUS Manuel utilisateur

Marque: LITE ON

Modèle: NIUS

Taper: Manuel utilisateur

2022/2/7

Page 1/9 2022/2/7

USER MANUAL

802.11 b/g/n, 1T1R 2.4GHz Module

Model: NIUS

WN3602M-PLUS (3.3V/5V)

NXP 88MW320

Version 1.0

2022/2/7

PRODUCT FEATURES

 IEEE 802.11b/g/n, 1×1 SISO 2.4 GHz

 Compact Form Factor: 30x17x1mm (PCB) ±0.1mm

 Integrated CPU, memory, MAC, DSSS/OFDM baseband,

direct conversion RF radio, encryption

 CMOS and low-swing sine wave input clock

 Low-power with deep sleep and standby modes

 Integrated T/R switch, PA, and LNA

 HF/RoHS compliance

PRODUCT SPECIFICATIONS

MAIN CHIPSET

NXP 88MW320-A0-NAPE/AZ

FUNCTIONAL SPECIFICATIONS

WiFi Function

Standard IEEE802.11b; IEEE 802.11g; IEEE 802.11n

Bus Interface UART

Data Rate

802.11b:

11, 5.5, 2, 1 Mbps

802.11g:

54, 48, 36, 24, 18, 12, 9, 6 Mbps

802.11n:

MCS 0 to 7

Media Access Control CSMA/CA with ACK

Modulation Techniques

802.11b:

CCK, DQPSK, DBPSK

802.11g:

64QAM, 16QAM, QPSK, BPSK

802.11n:

BPSK, QPSK, 16QAM, 64QAM

Network Architecture

Ad-hoc mode (Peer-to-Peer)

Infrastructure mode

Operation Channel

2.4GHz

11: (Ch. 1-11) – United States

13: (Ch. 1-13) – Europe

14: (Ch. 1-14) – Japan

Frequency Range

802.11bg

2.412 ~ 2.462 GHz

Transmit Output Power – 1x1

(Tolerance: +-1.5dBm)

802.11b:

11b(1M~11M) :16dBm

2022/2/7

802.11g:

11g(6M~18M) :16dBm

11g(24~54M): 15dBm

802.11n:

11n(MCS0~MCS7) :13dBm

Receive Sensitivity

802.11b: (IEEE Standard <-76dBm)

typical: -87.5dBM(1M)

802.11g: (IEEE Standard <-65dBm)

Typical: -73dBm(54M)

802.11n:

20MHz (IEEE Standard <-64dBm)

Typical: -71dBm

Security

WPA, WPA2, WPS, WEP 64/128, IEEE 802.11x, IEEE

802.11i

Operating Voltage 5V or 3.3V ±10% supply voltage

Power Consumption

(Average)

165mA@16dBm

Antenna Type Printed Antenna

2022/2/7

PIN DEFINITION

Name

Type

UART2_RX

UART0_RX

UART0_TX

5V Power in

3.3V

3.3V Power in

GND

Ground

RESET

IC Reset

BOOT

I/O

GPIO10

JTAG-TRST

GPIO9

JTAG-TDI

GPIO8

I/O

JTAG-TMS

GPIO7

JTAG-CLK

GPIO6

JTAG-TDO

UART1_RX

UART1_TX

UART2_TX

2022/2/7

MECHANICAL

WN3602M (3.3V)

WN3602M (5V)

Unit : mm ; Tolerance : +/- 0.1mm

RECOMMEND FOOTPRINT

Unit : mm

2022/2/7

ENVIRONMENTAL

Operating

Operating Temperature: 0 to 70 °C

Relevant Humidity: 5-90% (non-condensing)

Storage

Temperature: -40 to 85 °C

Relevant Humidity: 5-95% (non-condensing)

2022/2/7

WARNINGS

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's

authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation.

This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.

For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be

installed and operated with minimum distance 20cm between the radiator & your body.

ISED Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development

Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1.This device may not cause interference.

2.This device must accept any interference, including interference that may cause undesired operation of the device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et

Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux

conditions suivantes :

1.L’appareil ne doit pas produire de brouillage;

2.L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le

fonctionnement.

ISED Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment

should be installed and operated with minimum distance 20cm between the radiator & your body.

Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet

équipement doit être installé et utilisé avec un minimum de 20cm de distance entre la source de rayonnement et votre corps.

The transmitter module may not be co-located with any other transmitter or antenna.

Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.

For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.

Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être exploités. Sélection d'autres

canaux n'est pas possible.

2022/2/7

This module is intended for OEM integrators under the following conditions:

1. Ensure that the end-user has no manual instructions to remove or install module.

2.This module is certified pursuant to Part 15 rules section 15.247 and RSS-247.

3.This module has been approved to operate with the antenna types listed below, with the maximum permissible gain indicated.

Antenna Frequency Band Antenna Type Brand

Model

Number

Gain(dBi)

1 2400-2483.5MHz Printed Antenna LITEON WN3602M -0.9

4.Label and compliance information

Label of the end product:

FCC

The host product must be labeled in a visible area with the following " Contains FCC ID: 2AIBX-NIULL".

The end product shall bear the following 15.19 statement: This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

ISED

This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be

maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains

transmitter module IC: 21700-NIULL” or “Contains IC: 21700-NIULL”

Contient le module d'émission IC: 21700-NIULL

5.Information on test modes and additional testing requirements

This module has been approved under stand-alone configuration.

OEM integrator has be limited the operation channels in channel 1-11 for 2.4GHz band.

The separate approval is required for all other operating configurations, including portable configurations with respect to Part

2.1093/RSS-102 and different antenna configurations

The information on how to configure test modes for host product evaluation for different operational conditions for a stand-alone

modular transmitter in a host, versus with multiple, simultaneously transmitting modules or other transmitters in a host can be

found at KDB Publication 996369 D04.

OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this

module installed (for example, digital device emissions, PC peripheral requirements, etc.).

IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with

another transmitter), then the FCC/ISED authorization is no longer considered valid and the FCC/IC No. cannot be used on the final

product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the

transmitter) and obtaining a separate FCC/ISED authorization.

6.Additional testing, Part 15 Subpart B and ICES-003 disclaimer

Appropriate measurements (e.g. Part 15 Subpart B compliance) and if applicable additional equipment authorizations (e.g. SDoC) of

the host product to be addressed by the integrator/manufacturer.

This module is only FCC/ISED authorized for the specific rule parts 15.247, RSS-247 listed on the grant, and the host product

manufacturer is responsible for compliance to any other FCC/ISED rules that apply to the host product as being Part 15 Subpart

B/ICES-003 compliant.

7.The user manual of the end product should include:

FCC:

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to

operate this equipment.

The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation.

The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter.

2022/2/7

ISED: