Page 1/10 2021/7/28
USER MANUAL
802.11 b/g/n, 1T1R 2.4GHz Module
Model: NIU-LIGHT
WN3602M (3.3V/5V)
Page 2/10 2021/7/28
PRODUCT FEATURES
IEEE 802.11b/g/n, 1×1 SISO 2.4 GHz
Compact Form Factor: 30x17x1mm (PCB) ±0.1mm
Integrated CPU, memory, MAC, DSSS/OFDM baseband,
direct conversion RF radio, encryption
CMOS and low-swing sine wave input clock
Low-power with deep sleep and standby modes
Integrated T/R switch, PA, and LNA
HF/RoHS compliance
PRODUCT SPECIFICATIONS
MAIN CHIPSET
NXP 88MW320
FUNCTIONAL SPECIFICATIONS
WiFi Function
Standard IEEE802.11b; IEEE 802.11g; IEEE 802.11n
Bus Interface UART
Data Rate
802.11b:
11, 5.5, 2, 1 Mbps
802.11g:
54, 48, 36, 24, 18, 12, 9, 6 Mbps
802.11n:
MCS 0 to 7
Media Access Control CSMA/CA with ACK
Modulation Techniques
802.11b:
CCK, DQPSK, DBPSK
802.11g:
64QAM, 16QAM, QPSK, BPSK
802.11n:
BPSK, QPSK, 16QAM, 64QAM
Network Architecture
Ad-hoc mode (Peer-to-Peer)
Infrastructure mode
Operation Channel
2.4GHz
11: (Ch. 1-11) – United States
13: (Ch. 1-13) – Europe
14: (Ch. 1-14) – Japan
Frequency Range
802.11bg
2.412 ~ 2.462 GHz
Page 3/10 2021/7/28
Transmit Output Power – 1x1
(Tolerance: +-1.5dBm)
802.11b:
16dBm
802.11g:
16dBm
802.11n:
13dBm
Receive Sensitivity
802.11b: (IEEE Standard <-76dBm)
typical: -87.5dBM(1M)
802.11g: (IEEE Standard <-65dBm)
Typical: -73dBm(54M)
802.11n:
20MHz (IEEE Standard <-64dBm)
Typical: -71dBm
Security
WPA, WPA2, WPS, WEP 64/128, IEEE 802.11x, IEEE
802.11i
Operating Voltage 5V or 3.3V ±10% supply voltage
Power Consumption
(Average)
TBD
Antenna Type Printed Antenna
Page 4/10 2021/7/28
PIN DEFINITION
PIN
Name
Type
1
UART2_RX
I
2
UART0_RX
I
3
UART0_TX
O
4
5V
P
5V Power in
5
3.3V
P
3.3V Power in
6
GND
GND
Ground
7
RESET
I
IC Reset
8
BOOT
I/O
9
GPIO10
I
JTAG-TRST
10
GPIO9
I
JTAG-TDI
11
GPIO8
I/O
JTAG-TMS
12
GPIO7
I
JTAG-CLK
13
GPIO6
O
JTAG-TDO
14
UART1_RX
I
15
UART1_TX
O
16
UART2_TX
O
Page 5/10 2021/7/28
MECHANICAL
WN3602M (3.3V)
WN3602M (5V)
Unit : mm ; Tolerance : +/- 0.1mm
RECOMMEND FOOTPRINT
Unit : mm
Page 6/10 2021/7/28
ENVIRONMENTAL
Operating
Operating Temperature: 0 to 70 °C
Relevant Humidity: 5-90% (non-condensing)
Storage
Temperature: -40 to 85 °C
Relevant Humidity: 5-95% (non-condensing)
Page 7/10 2021/7/28
WARNINGS
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any other
antenna or transmitter.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of
other channels is not possible.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
ISED Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following
two conditions:
1.This device may not cause interference.
2.This device must accept any interference, including interference that may cause undesired
operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
Page 8/10 2021/7/28
1.L’appareil ne doit pas produire de brouillage;
2.L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
ISED Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20cm
de distance entre la source de rayonnement et votre corps.
The transmitter module may not be co-located with any other transmitter or antenna.
Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of
other channels is not possible.
Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être
exploités. Sélection d'autres canaux n'est pas possible.
This module is intended for OEM integrators under the following conditions:
1. Ensure that the end-user has no manual instructions to remove or install module.
2.This module is certified pursuant to Part 15 rules section 15.247 and RSS-247.
3.This module has been approved to operate with the antenna types listed below, with the
maximum permissible gain indicated.
Antenna Frequency Band Antenna Type Brand
Model
Number
Gain(dBi)
1 2400-2483.5MHz Printed Antenna LITEON WN3602M -0.9
4.Label and compliance information
Label of the end product:
FCC
The host product must be labeled in a visible area with the following " Contains FCC ID:
2AIBX-NIULL".
The end product shall bear the following 15.19 statement: This device complies with part 15 of the
FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
ISED
This transmitter module is authorized only for use in device where the antenna may be installed
such that 20 cm may be maintained between the antenna and users. The final end product must be
labeled in a visible area with the following: “Contains transmitter module IC: 21700-NIULL” or
Page 9/10 2021/7/28
“Contains IC: 21700-NIULL”
Contient le module d'émission IC: 21700-NIULL
5.Information on test modes and additional testing requirements
This module has been approved under stand-alone configuration.
OEM integrator has be limited the operation channels in channel 1-11 for 2.4GHz band.
The separate approval is required for all other operating configurations, including portable
configurations with respect to Part 2.1093/RSS-102 and different antenna configurations
The information on how to configure test modes for host product evaluation for different
operational conditions for a stand-alone modular transmitter in a host, versus with multiple,
simultaneously transmitting modules or other transmitters in a host can be found at KDB
Publication 996369 D04.
OEM integrator is still responsible for testing their end product for any additional compliance
requirements required with this module installed (for example, digital device emissions, PC
peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC/ISED authorization is no
longer considered valid and the FCC/IC No. cannot be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end product (including
the transmitter) and obtaining a separate FCC/ISED authorization.
6.Additional testing, Part 15 Subpart B and ICES-003 disclaimer
Appropriate measurements (e.g. Part 15 Subpart B compliance) and if applicable additional
equipment authorizations (e.g. SDoC) of the host product to be addressed by the
integrator/manufacturer.
This module is only FCC/ISED authorized for the specific rule parts 15.247, RSS-247 listed on the
grant, and the host product manufacturer is responsible for compliance to any other FCC/ISED rules
that apply to the host product as being Part 15 Subpart B/ICES-003 compliant.
7.The user manual of the end product should include:
FCC:
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate this equipment.
The antenna(s) used for this transmitter must be installed to provide a separation distance of at
least 20 cm from all persons.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna
or transmitter.
Page 10/10 2021/7/28
ISED:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following
two conditions:
1.This device may not cause interference.
2.This device must accept any interference, including interference that may cause undesired
operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
1.L’appareil ne doit pas produire de brouillage;
2.L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
ISED Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20cm
de distance entre la source de rayonnement et votre corps.
The transmitter module may not be co-located with any other transmitter or antenna.
Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of
other channels is not possible.
Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être
exploités. Sélection d'autres canaux n'est pas possible.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
dans d''autres langues
- English: LiteOn NIU-LIGHT User manual
Documents connexes
Autres documents
-
LITE ON NIUS Manuel utilisateur
-
LITE ON QCS403YA Manuel utilisateur
-
Hisense AEH-W0G1 Mode d'emploi
-
GSD WXT2AM2101 WIFI+BT Module IEEE Manuel utilisateur
-
LITE ON WCBN3606L Manuel utilisateur
-
GSD WC0PR1601 Le manuel du propriétaire
-
GSD WC5EM2601F Dual Band WiFi Module Manuel utilisateur
-
Mediatek MT7922A22M Mode d'emploi
-
GSD WC5F Manuel utilisateur
