GSD WXT2AM2101 WIFI+BT Module IEEE Manuel utilisateur

WXT2AM2101 WIFI+BT Module IEEE
Marque
GSD
Modèle
WXT2AM2101 WIFI+BT Module IEEE
Taper
Manuel utilisateur

Ce manuel convient également à

Hui Zhou Gaoshengda Technology Co., LTD WXT2AM2101
PAGE 1 OF 4
Version 1.0
WIFI+BT Module
IEEE 802.11 a/b/g/n/ac/ax 2T/2R
Model Number: WXT2AM2101
Product Descrition
The WXT2AM2101 is a complete 2.4GHz/5GHz/6GHz WIFI 2×2 MIMO module. This module provides a high level
of integration with a dual-stream IEEE 802.11ax MAC/ base band /radio and Bluetooth 5.2.The WLAN operation
supports 20MHz,40MHz and 80MHz channels for data rates up to 1201Mbps. It fully complies with IEEE 802.11
a/b/g/n/ac/ax feature rich wireless connectivity at high standards,delivers reliable,cost-effective, throughput from
an extended distance.
Product Features
Product Specification
Model
WXT2AM2101
Product Name
WIF+BT Module
Standard
802.11 a/b/g/n/ac/ax
Interface
USB
Data Transfer Rate
1,2,5.5,6,11,12,18,22,24,30,36,48,54,60,90,120 and maximum of 1201Mbps
Modulation Method
GFSK,π/4-DQPSK,8DPSK(bluetooth)
DQPSK,DBPSK,CCK(802.11b)
QPSK,BPSK,16QAM,64QAM with OFDM (802.11g)
QPSK,BPSK,16QAM,64QAM with OFDM (802.11n)
QPSK,BPSK,16QAM,64QAM with OFDM (802.11a)
QPSK,BPSK,16QAM,64QAM,256QAM with OFDM (802.11ac)
QPSK,BPSK,16QAM,64QAM,256QAM,1024QAM with OFDM (802.11ax)
Frequency Band
BLUETOOTH
2402~2480 MHz
WIFI
2.4G: 2412~2462 MHz
5G: 5150~5350MHz, 5470~5725MHz，5725~5850MHz
6G: 5925~7125MHz
Operation Mode
Infrastructure
Security
WEP, TKIP, AES, WPA, WPA2
Operating Voltage
3.3V±10%
Current Consumption
＜1000mA
Antenna Type
PIFA
Operating
Temperature
0 ~ 70°C ambient temperature
Storage Temperature
-40 ~ 80°C ambient temperature
Humidity
5 to 95 % maximum (non-condensing)
◆ Complies with IEEE 802.11b/g/n/ax for 2.4GHz，IEEE 802.11a/n/ac/ax for 5GHz，IEEE 802.11ax
for 6GHz Wireless LAN.
◆ Bluetooth v5.2
◆ Two transmit and Two receive path(2T2R)
◆ Works with all existing network nfrastructure.
◆ Capable of up to 128-Bit WEP Encryption.
◆ Freedom to roam while staying connected.
◆ UP to 1201 Mbps High-Speed Transfer Rate in 802.11ax mode of operation.
◆ Operating Systems：Linux, Win10, Win11.
◆ Low power consumption.
◆ Easy to install and configure.
◆ High speed usd 2.0 interface.
◆ROHS compliant
Hui Zhou Gaoshengda Technology Co., LTD WXT2AM2101
PAGE 2 OF 4
Version 1.0
NOTICE:
◆please keep this product and accessories attached to the places which children can't touch;
◆do not splash water or other liquid onto this product, otherwise it may cause damage;
◆do not put this product near the heat source or direct sunlight, otherwise it may cause
deformation or malfunction;
◆please keep this product away from flammable or naked flame;
◆please do not repair this product by yourself. Only qualified personnel can be repaired.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Please notice that if the FCC identification number is not visible when the module is
installed inside another device, then the outside of the device into which the module is
installed must also display a label referring to the enclosed module. This exterior label
can use wording such as the following: “Contains FCC ID:2AC23-WXT2A” any similar wording
that expresses the same meaning may be used.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of
20cm between the radiator & your body. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.
Hui Zhou Gaoshengda Technology Co., LTD WXT2AM2101
PAGE 3 OF 4
Version 1.0
The module is limited to OEM installation ONLY.
The OEM integrator is responsible for ensuring that the end-user has no manual instruction
to remove or install module.
The module is limited to installation in mobile application.
A separate approval is required for all other operating configurations, including portable
configurations with respect to Part 2.1093 and difference antenna configurations.
There is requirement that the grantee provide guidance to the host manufacturer for
compliance with Part 15B requirements.
The module complies with FCC Part 15.247 / Part 15.407 and apply for Single module approval.
Trace antenna designs: Not applicable.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20cm
between the radiator & your body. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
The device must be professionally installed The intended use is generally not for the general public.It is generally for
industry/commercial use.The connector is within the transmitter enclosure and can only be accessed by disassembly of the
transmitter that is not normally required. the user has no access to the connector. Installation must be controlled. Installation
requires special training This module has been assessed against the following FCC rule parts: CFR 47 FCC Part 15 C
(15.247, DTS and DSS) and CFR 47 FCC Part 15 E (NII). It is applicable to the modular transmitter。
This radio transmitter 12290A-WXT2A has been approved by Innovation, Science and Economic
Development Canada to operate with the antenna types listed below, with the maximum permissible
gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain
indicated for any type listed are strictly prohibited for use with this device.
Le présent émetteur radio 12290A-WXT2A a été approuvé par Innovation, Sciences et Développement
économique Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain
admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au
gain maximal indiqué pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de
l'émetteur.
The concrete contents to check are the following three points.
１) Must use following one antenna.
２) Should be installed so that the end user cannot modify the antenna;
３) Feed line should be designed in 50ohm
Fine tuning of return loss etc. can be performed using a matching network.
Le contenu concret à vérifier sont les trois points suivants.
１) Une des trois antennes suivantes doit être utilisée.
２) doivent être installés de façon que l'utilisateur final ne peut pas modifier l'antenne
３) La ligne d’alimentation doit être conçue en 50ohm
Le réglage précis de la perte de rendement, etc. peut être effectué en utilisant un réseau correspondant.
For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall
be such that the equipment still complies with the e.i.r.p. limits as appropriate;
If the module intended to installed to a protable devices, a permissive change may need before used.
Hui Zhou Gaoshengda Technology Co., LTD WXT2AM2101
PAGE 4 OF 4
Version 1.0
BLE:
Antenna
Antenna Type
MAX Antenna Gain (dBi)
1
PIFA
2
BT:
Antenna
Antenna Type
MAX Antenna Gain (dBi)
1
PIFA
2
2.4G wifi：
Antenna
Antenna Type
MAX Antenna Gain (dBi)
1
PIFA
2
2
PIFA
2
5G:
Antenna No.
Frequency Band
Antenna Type
Max Antenna Gain (dBi)
1
5180 ~ 5825
PIFA
3
2
5180 ~ 5825
PIFA
3
Wifi 6E:
Antenna No.
Frequency Band
Antenna Type
Max Antenna Gain (dBi)
1
5925 ~ 7125
PIFA
4
2
5925 ~ 7125
PIFA
4
The antenna is permanently attached, can’t be replaced.
Canada Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to
the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired
operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage;
Hui Zhou Gaoshengda Technology Co., LTD WXT2AM2101
PAGE 5 OF 4
Version 1.0
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
Please notice that if the ISED certification number is not visible when the module is installed inside another device, then
the outside of the device into which the module is installed must also display a label referring to the enclosed module. This
exterior label can use wording such as the following: “Contains IC:12290A-WXT2A” any similar wording that expresses
the same meaning may be used.
l'appareil hôte doit porter une étiquette donnant le numéro de certification du module d'Industrie Canada, précédé des
mots « Contient un module d'émission », du mot « IC:12290A- WXT2A » ou d'une formulation similaire exprimant le mê
me sens, comme suit
The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference
to co-channel mobile satellite systems
For devices with detachable antenna(s), the maximum antenna gain permitted for devices in
the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies
with the e.i.r.p. limit;
For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall
be such that the equipment still complies with the e.i.r.p. limits as appropriate;
Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur
afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et5 470-5 725 MHz doit se
conformer à la limite de p.i.r.e.;
pour les dispositifs munis d'antennes amovibles, le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de
5 725 à 5 850 MHz) doit être conforme à la limite de la p.i.r.e. spécifiée, selon le cas;
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102
RF exposure, users can obtain Canadian information on RF exposure and compliance.
Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 etla conformité à
l'exposition de RSS-102 RF, utilisateurs peut obtenir l'information canadienne surl'exposition et la conformité de rf.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment
should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenne ouémetteur. Cet é
quipement devrait être installé et actionné avec une distance minimum de 20 centimètres
entre le radiateur et votre corps.
This radio transmitter [IC : 12290A- WXT2A] has been approved by Innovation, Science and Economic Development
Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not
included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for
use with this device.
Hui Zhou Gaoshengda Technology Co., LTD WXT2AM2101
PAGE 6 OF 4
Version 1.0
Le présent émetteur radio 12290A- WXT2A a été approuvé par Innovation, Sciences et Développement économique
Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain
admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est
supérieur au gain maximal indiqué pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de l'é
metteur.
The concrete contents to check are the following three points.
１) Doit utiliser une antenne PIFA avec un gain ne dépassant pas 2 dBi pour 2,4G et ne dépassant pas 3 dBi pour 5G,
ne dépassant pas 4 dBi pour 6G.
２) Should be installed so that the end user cannot modify the antenna
３) Feed line should be designed in 50ohm
Fine tuning of return loss etc. can be performed using a matching network.
Le contenu concret à vérifier sont les trois points suivants.
１) Une antenne pifa dont le gain ne dépasse pas 3 DBI doit être utilisée pour 2,4 G et une antenne pifa dont le gain ne dé
passe pas 4 DBI doit être utilisée pour 6 G.
２) doivent être installés de façon que l'utilisateur final ne peut pas modifier l'antenne
３) La ligne d’alimentation doit être conçue en 50ohm
Le réglage précis de la perte de rendement, etc. peut être effectué en utilisant un réseau correspondant.
Antennas:
BLE:
Antenna
Antenna Type
MAX Antenna Gain (dBi)
1
PIFA
2
BT:
Antenna
Antenna Type
MAX Antenna Gain (dBi)
1
PIFA
2
2.4G wifi：
Antenna
Antenna Type
MAX Antenna Gain (dBi)
1
PIFA
2
2
PIFA
2
5G:
Antenna No.
Frequency Band
Antenna Type
Max Antenna Gain (dBi)
1
5180 ~ 5825
PIFA
3
2
5180 ~ 5825
PIFA
3
Hui Zhou Gaoshengda Technology Co., LTD WXT2AM2101
PAGE 7 OF 4
Version 1.0
Wifi 6E:
Antenna No.
Frequency Band
Antenna Type
Max Antenna Gain (dBi)
1
5925 ~ 7125
PIFA
4
2
5925 ~ 7125
PIFA
4
The antenna is permanently attached, can’t be replaced.
Notice to OEM integrator
Must use the device only in host devices that meet the FCC/ISED RF exposure category of mobile, which means the
device is installed and used at distances of at least 20cm from persons.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements related to the transmitter as
show in this manual(FCC/ICanada statement).
According to FCC Part 15 Subpart C Section 15.212, the radio elements of the modular transmitter must have the
radio frequency circuitry shielded. However, due to there is no shielded for this Module, this module is granted as a
Limited Modular Approval. When this Module is installed into the end product, a Class II Permissive Change or a New
FCC ID submission is required to ensure the full compliance of FCC relevant requirements.
Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter
when the module is installed in the host.
The use condition limitations extend to professional users, then instructions must state that this information also
extends to the host manufacturer’s instruction manual.
This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting
condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer
have to consult with module manufacturer for the installation method in end system.
Any company of the host device which install this modular should perform the test of radiated &
condicted emission and spurious emission etc. according to FCC Part 15C: 15.247 and 15.209 &
15.207, 15B class B requirement, only if the test result comply with FCC part 15C: 15.247 and
15.209 & 15.207, 15B class B requirement. Then the host can be sold legally.
This modular transmitter is only FCC authorized for the specific rule parts ( 47CFR Part 15.247
and 15.407) listed on the grant, and that the host product manufacturer is responsible for
compliance to any other FCC rules that apply to the host not covered by the modular transmitter
grant of certification.
Host manufacturer is strongly recommended to confirm compliance with FCC/ISED
requirements for the transmitter when the module is installed in the host.
Must have on the host device a label showing Contains FCC ID:2AC23-WXT2A and IC:12290A- WXT2A
Installer should put it in the manual：
The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful
interference to co-channel mobile satellite systems
Hui Zhou Gaoshengda Technology Co., LTD WXT2AM2101
PAGE 8 OF 4
Version 1.0
l'hôte doit utiliser l'instrument uniquement dans des dispositifs qui répondent à la fcc / (catégorie d'exposition rf
mobile, ce qui signifie le dispositif est installé et utilisé à une distance d'au moins 20 cm de personnes.
le manuel de l'utilisateur final doit inclure la partie 15 / (fac rss gen déclarations de conformité relatives à
l'émetteur que de montrer dans ce manuel.
le fabricant est responsable de la conformité de l'hôte, le système d'accueil avec le module installé avec toutes
les autres exigences applicables du système comme la partie 15 b, ices - 003.
accueillir le fabricant est fortement recommandé de confirmer la conformité avec les exigences de la fcc /
(émetteur lorsque le module est installé dans l'hôte.
le dispositif d'accueil doivent avoir une étiquette indiquant contient FCC ID: 2AC23- WXT2A，IC: 12290A- WXT2A
Les personnes chargées de l'installation devraient figurer dans le manuel:
Les dispositifs fonctionnant dans la bande de 5 150 à 5 250 MHz sont réservés uniquement pour une utilisation
à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les
mêmes canaux.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

GSD WXT2AM2101 WIFI+BT Module IEEE Manuel utilisateur

WXT2AM2101 WIFI+BT Module IEEE
Marque
GSD
Modèle
WXT2AM2101 WIFI+BT Module IEEE
Taper
Manuel utilisateur
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents