Chief KFA220B Guide d'installation
- Catégorie
- Accessoires pour écran plat
- Taper
- Guide d'installation
INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
KFA-220/225
KFA-320/325
Carts and Stands Horizontal Array Accessory
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
KFA SERIES
KFA SERIES Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® and Centris™ a registered trademarks of Milestone AV
Technologies. All rights reserved.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
the displays installed does not exceed 70 lbs (31.8 kg) for the
KFA-220 and KFA-225 and 90 lbs (40.8 kg) for the KFA-320
and KFA-325. The weight of each individual display must not
exceed 35 lbs (15.9 kg) for the KFA-220 and KFA-225 or 30
lbs for the KFA-320 and KFA-325.
WARNING: RISK OF ELECTRIC SHOCK ! Using the
wrong screws could result in severe personal injury or
damage to your display. If your display uses a longer screw
size than those included in the kit, DO NOT use the screws
provided with the kit. Use the screws provided with your
display or contact the manufacturer.
WARNING: Improper installation can result in serious
personal injury! Make sure that the mounting surface can
support a redundant weight factor five times the total weight
of the equipment. If not, reinforce the mounting surface
structural members before installing the mount.
WARNING: Be aware of the potential for personal injury or
damage to the unit if it is not adequately mounted.
WARNING: The installer is responsible for verifying that
the mounting surface to which the KFA is anchored will safely
support the combined load of all attached components or
other equipment.
WARNING: Watch for pinch points. Do not put your fingers
between movable parts.
WARNING: Make sure the mount is correctly oriented.
Installation Instructions KFA SERIES
3
KFA-220 DIMENSIONS
KFA-225 DIMENSIONS
23.83
13.68
5.68
CLAMP FOR ATTACHING
TO PF AND MF SERIES
CARTS AND STANDS
1.96
4.50
IF SAME SIZE DISPLAY IS USED FOR BOTH,
MAXIMUM SCREEN WIDTH OF 22.7".
30.51
774.8
17.24
437.8
6.68
CLAMP FOR ATTACHING
TO PF AND MF SERIES
CARTS AND STANDS
1.96
49.8
4.50
114.3
IF SAME SIZE DISPLAY IS USED FOR BOTH,
MAXIMUM SCREEN WIDTH OF 30.0".
KFA SERIES Installation Instructions
4
KFA-320 DIMENSIONS
KFA-325 DIMENSIONS
20.80
528.3
37.14
943.3
7.93
201.5
IF SAME SIZE DISPLAY IS USED FOR ALL THREE,
MAXIMUM SCREEN WIDTH OF 18.0".
CLAMP FOR ATTACHING
TO PF AND MF SERIES
CARTS AND STANDS
1.96
49.8 4.50
114.3
53.81
1366.7
10.87
276.1
48.69
1236.7
IF SAME SIZE DISPLAY IS USED FOR ALL THREE,
MAXIMUM HORIZONTAL SCREEN WIDTH OF 25.00" [635.0].
CLAMP FOR ATTACHING
TO PF AND MF SERIES
CARTS AND STANDS
1.96
49.8 4.50
114.3
Installation Instructions KFA SERIES
5
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
KFA SERIES Installation Instructions
6
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2
5/32"
(included)
(refer to Table 1 for quantities and part descriptions)
A
B
CD
G
EF
H
J
K
L
M
Installation Instructions KFA SERIES
7
Installation
1. Determine proper pole clamp to use for installation. If
mounting to wide portion of pole mount use large pole
clamp bracket (K). If mounting to extendable upper portion
of mount, use small pole clamp bracket (J). (See Figure 1)
Figure 1
NOTE: If removing existing head assembly from cart/stand, do
so prior to installing KFA Series arrays.
IMPORTANT ! : The KFA Series arrays can be used in
addition to the existing head assembly as long as the
overall weight limit of the cart/stand is not exceeded!
2. Attach pole clamp bracket (J or K) to pole mount front
using two 1/4" washers (L) and two 1/4-20 x 3/4"
button head cap screws (M). (See Figure 2)
3. Secure pole clamp bracket (J or K) to pole mount front
and pole by tightening two button head cap screws
(M) using a 5/32" hex key (H). (See Figure 2)
Figure 2
Display Installation
Attach Centris Head to Flush Mount Display
CAUTION: If display uses a screw size other than
those included in the kit, DO NOT use the screws
provided. Using the wrong screws could result in
damage to your monitor.
1. Install two M4 x 12mm Phillips pan head screws (C)
into two upper mounting holes in display back.
(See Figure 3)
NOTE: DO NOT fully tighten at this time.
2. Hang display on Centris head. (See Figure 4)
3. Install bottom two M4 x 12mm Phillips pan head
screws (C) through Centris head mounting holes and
into lower mounting holes in display back.
4. Tighten four M4 x 12mm Phillips pan head screws
(C). (See Figure 5)
Table 1: Parts
ITEM DESCRIPTION QTY*
AARRAY ASSEMBLY, KFA-220/225 1
B ARRAY ASSEMBLY, KFA-320/325 1
CSCREW, Phillips Pan Head, M4 x 12mm 4
D SCREW, Phillips Pan Head, M4 x 30mm 4
ESPACER, Nylon, 3/4" (used with item D) 4
F SPACER, Nylon, 3/8" (used with item G) 4
GSCREW, Phillips Pan Head, M4 x 20mm 4
HKEY, Hex, 5/32" 1
JBRACKET, Pole Clamp, Back - small 1
KBRACKET, Pole Clamp, Back - large 1
LWASHER, Flat. 1/4" 2
MSCREW, Button Head, 1/4-20 x 3/4" 2
* Quantity varies depending upon the number of displays being
mounted.
(J)
(K)
(J or K)
(M) x 2
(L) x 2
(A or B)
pole mount
KFA SERIES Installation Instructions
8
Figure 3
Figure 4
Figure 5
Attach Centris Head to Recessed Mount Display
CAUTION: If display uses a screw size other than
those included in the kit, DO NOT use the screws
provided. Using the wrong screws could result in
damage to your monitor.
1. Uninstall end lock using the 5/32" hex key (H). (See
Figure 6)
2. Remove Centris head from mounting rail.
(See Figure 7)
Figure 6
Figure 7
3. Place display face down on a clean dry surface.
4. Place four 3/4" or 3/8" nylon spacers (E or F) over four
mounting holes in display back.
NOTE: Refer to Table 1 to select the applicable screw
and spacer combination.
5. Align Centris head mounting holes with four nylon
spacers.
6. Secure Centris head to display using four
M4 x 20mm Phillips pan head screws (G), or four M4
x 30mm Phillips pan head screws (D).(See Figure 8)
Display
(C) x 2
1
2
Display
Centris Head
Array Rail
Display
Centris Head
Array Rail
(C) x 2
3
Square Nut
End Lock
Centris Head
Array Rail
1
Centris Head
Array Rail
2
Installation Instructions KFA SERIES
9
Figure 8
7. Slide display with Centris bracket onto mounting rail.
(See Figure 9)
NOTE: Repeat previous steps for each additional display.
8. Install end locks into mounting rail using the 5/32" hex
key (H). (See Figure 10)
Figure 9
Figure 10
Display Adjustment
These pivot arrays allow horizontal, pitch, roll, and yaw
adjustment of each display with a maximum pitch range
of 15° up and 15° down.
These pivot arrays also allow a full 360 deg. of display
roll.
Display Horizontal Position Adjustment
To adjust display horizontal position:
1. Loosen Centris bracket rear adjustment knob.
(See Figure 11)
2. Slide Centris bracket with display left or right until
properly positioned on array rail.
3. Tighten Centris bracket rear adjustment knob.
Figure 11
Display Pitch, Roll, and Yaw Adjustment
To adjust display position:
1. Loosen Centris bracket front adjustment knob.
(See Figure 12)
2. Tilt display up or down, or adjust display roll left or
Display
Centris Head
(G or D) x 4
(E or F) x 4
4
5
6
Display with Centris Bracket
Array Rail
7
End Lock
End Lock Retaining Screw Centris Head
Array Rail
rear adjustment knob
KFA SERIES Installation Instructions
10
right until properly positioned.
3. Tighten Centris bracket front adjustment knob.
Figure 12
pitch/roll adjustment knob
Installation Instructions KFA SERIES
11
KFA SERIES Installation Instructions
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P800.582.6480 / 952.894.6280
F877.894.6918 / 952.894.6918
Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P+31 (0)40 2668620
F+31 (0)40 2668615
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
Chief Manufacturing, a products division
of Milestone AV Technologies
8834-000011 REV 01
2010 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
04/10
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Chief KFA220B Guide d'installation
- Catégorie
- Accessoires pour écran plat
- Taper
- Guide d'installation
dans d''autres langues
- English: Chief KFA220B Installation guide
Documents connexes
-
Chief PACTP1 Guide d'installation
-
-
Chief JWSVB Guide d'installation
-
-
-
-
Chief FCA540 Guide d'installation
-
-
-
Chief JPPVB Guide d'installation
