Uniden PRO510 XL Le manuel du propriétaire

Marque: Uniden

Modèle: PRO510 XL

Taper: Le manuel du propriétaire

Ce manuel convient également à

PRO510XL

PRO 510XL

Professional

Mobile CB Radio

Printed in Vietnam

UTZZ01363AA(1)

Irving, Texas

Sheet 1

INTRODUCTION

Welcome to the world of Citizens Band radio communications. Your Uniden

PRO510 radio is an advanced mobile radio designed for use in the Citizens

Band (CB) Radio Service. It will operate on any of the 40 AM frequencies

authorized by the Federal Communications Commission (FCC). Your Radio

features a superheterodyne circuit with PHASE LOCKED LOOP techniques to

assure precise frequency control.

Safety Notice

The antenna used for this radio must be properly installed and maintained

and must provide a separation distance of at least 16.92 inches (43 cm) from

all persons and must not be collocated or operated in conjunction with any

other antenna or transmitter. Never transmit if any person is closer than the

specied distance to the antenna.

Note that Uniden does not specify or supply any antenna with this transceiver.

While a 0 dBi gain antenna is normal for a typical installation, the above limit

applies to any antenna with up to 3 dBi gain.

CB license requirement

U.S. users no longer need to apply for a license to use a CB radio. However,

CB radio is still considered a “license by rule” service. This means that, while

the FCC permits CB station operation without station identication, station

operators are still required to comply with the Communications Act and with

the rules of CB Radio Service. (For more information on U.S. radio rules, visit

the FCC website at www.fcc.gov.)

Sheet 1

Uniden contact information

You can get answers 24/7 at our website: www.uniden.com.

INCLUDED IN YOUR PACKAGE

If any of these items are missing or damaged, immediately contact your place

of purchase or www.uniden.com.

PRO510 XL Mobile radio

Microphone and hook

Mounting bracket and knobs

Mounting hardware

Other printed materials

NOTE: You must use a CB antenna (sold separately) with this radio.

Sheet 1

PARTS OF THE RADIO

Front

1. ANL Switch

Activates the Automatic Noise Limiter feature, which reduces background

noise from the car engine and other sources.

2. TX LED

Indicates when the radio is transmitting.

3. S/RF (Signal/RF) Meter

Shows the strength of the received signal or the RF output.

4. Channel Indicator

Displays the channel currently in use.

5. Microphone Jack

Connects to the included detachable electret microphone.

6. Volume Control

Powers on the radio and adjusts the volume.

7 Squelch knob

Adjusts the level at which the radio squelches or suppresses weak radio

signals. To lter out weaker signals and background noise, turn the knob

clockwise to increase the squelch level. To decrease the squelch level so

you can hear weaker radio signals, turn the knob counter-clockwise.

8. Channel Selector

Selects which channel the radio will transmit or receive on.

NOTE: FCC rules reserve Channel 9 for motorist assistance and other

emergency communications. Channel 9 should only be used in situations

where there is immediate danger to the safety of individuals or the

protection of property.

8765

Sheet 1

Back

9. Model number label

Shows the radio model number, FCC ID number and serial number.

10. Antenna Connector

Connects to a male PL-259 external antenna cable (antenna sold

separately).

11. External Speaker Jack

Connects to a ⅛-inch (3.5 mm) external speaker (sold separately).

12. 12 Volt DC Power Cord

13. Fuse casing

Microphone

14 Push-to-talk (PTT) button

Press and hold the PTT button to transmit on the

selected channel. Release the button to listen for a

response.

For the best sound quality, hold the microphone

about 2 inches away from your mouth and speak in a normal voice.

NOTE: Make sure you have read and understood part 95 of the FCC rules

and regulations before using the transmitter.

MOD

O510

FCC ID

SERIAL NO:

Sheet 1

INSTALLATION

Connect the microphone

Align the microphone connector with the jack on the front of the radio. Push

the connector in rmly and secure it with the locking screw.

Connect the power

You can connect the radio to any standard 12 volt DC power source, with

either a positive or negative ground. If you don’t know whether your power

supply uses a positive or negative ground, consult the manual for your power

supply or contact the manufacturer.

WARNING! DO NOT connect this equipment to a power supply if you are

not absolutely certain of the grounding type!

1) Make sure your power supply is turned off.

2) For power supplies with a NEGATIVE ground, connect the RED lead

on the radio to the power supply’s POSITIVE (+) pole, and connect the

BLACK lead to the power supply’s NEGATIVE (–) pole or to a neutral

ground such as the chassis.

For power supplies with a POSITIVE ground, connect the BLACK lead on

the radio to the power supply’s NEGATIVE (–) pole, and connect the RED

lead to a neutral ground such as the chassis.

3) Turn on your power supply.

4) Turn the radio’s Volume knob clockwise to power on the radio.

Installing the mounting bracket

When choosing the location for the radio’s mounting bracket, keep the

following things in mind:

►Pick a location that does not block your view, interfere with your vehicle’s

controls, or hinder your driving.

►Make sure the radio and microphone are not in front of an airbag.

►Pick a solid surface that can support the weight of the bracket and the

radio.

►Make sure there’s enough room. (You may want to put the radio in the

bracket when you’re choosing where to install the bracket.)

Once you choose the location, use the included, self-tapping screws to attach

the mounting bracket and the microphone bracket to your vehicle (you don’t

have to drill holes). Slide the radio into the bracket and use the included knobs

to hold it at the preferred angle.

Sheet 2

Connecting an external antenna

You will need to purchase an antenna to operate the radio. However, Your

Uniden dealer can help you select the antenna that is best for your needs.

Consult the specications in the back of this manual for detailed transmitter

and antenna information.

There are two basic types of mobile CB antennas–full-length whips and loaded

whips–with a wide variety of mounts to suit different vehicle locations.

► Choose an antenna that matches the specications of this radio.

►Follow the manufacturer’s installation instructions carefully.

►Tune your antenna using a Standing-Wave Ratio (SWR) meter: set the

radio to channel 20, and adjust the antenna until the SWR is as close as

1:1 as possible.

CAUTION: Make sure the SWR is less than 2:1 before using the radio. An

SWR higher than 2:1 can damage the transmitter.

OPERATION AND MAINTENANCE

Basic operation

Turning the

radio on

Turn the Volume knob clockwise until the display backlight

comes on.

Turning the

radio off

Turn the Volume knob counter-clockwise until it clicks and

the display backlight turns off.

Selecting a

channel

Turn the Channel knob clockwise to move up the channel

list. Turn it counter-clockwise to move down the channel list.

Changing the

volume

Turn the Volume knob clockwise to increase the volume;

turn it counter-clockwise to decrease the volume.

Transmitting

–Tune the radio to the channel you want to transmit on, and

listen to make sure the channel is clear.

–Press and hold the PTT button.

–Hold the microphone about 2 inches away from your mouth

and speak in a normal voice.

–Release the button to listen for a response.

NOTE: Make sure you read and understood part 95 of the FCC rules and

regulations before using the transmitter.

Maintenance

Every six to twelve months, check to make sure that:

►The Voltage Standing Wave Ratio (VSWR) is less than 2:1.

►All electrical connections are secure and free of corrosion.

►The antenna cable shows no wear or damage.

Sheet 2

►All mounting screws are securely fastened.

►Inspect all screws and other mounting hardware.

TROUBLESHOOTING

If your radio is not performing to your expectations, please try these simple

steps. If these steps don’t solve your problem, visit www.uniden.com for

assistance.

Problem: Things to try:

Radio won’t turn

on (no power)

1. Check the radio’s power cord and all connections.

2. Check the fuse in the radio’s power cord.

3. Check your vehicle’s electrical system.

Poor reception

1. Adjust the squelch level.

2. Check the antenna, cable and connectors.

3. Check operation mode of the radio.

Background

noise

1. Turn on the automatic noise limiter.

2. Adjust the squelch level.

Weak

transmission

1. Check the antenna, cable and connectors.

2. Check the antenna grounding.

3. Check for corrosion on the connectors.

Service and repair information

► Service, repair, or alignment should only be attempted by a qualied and/

or licensed radio technician.

►When ordering parts, it is important to specify the correct model number of

this radio.

►It is the user’s responsibility to make sure the radio is operating in

accordance with the FCC Citizens Radio Service regulations at all times.

Sheet 2

SPECIFICATIONS

General

Channels 40 AM

Frequency Range 26.965 to 27.405 MHz

Frequency Control Phase Locked Loop (PLL) synthesizer

Frequency Tolerance ±0.005%

Operating

Temperature

-30ºC to +50ºC

Microphone Plug in type, dynamic

Input Voltage 13.8 V DC nom. (+ or - ground)

Current Drain TX full mod., 1.7A

RX with max. audio output, 1.7A

Size 4-1/2” W x 6-3/4” D x 1-3/8” H

Weight 1 lb. 9 oz.

Antenna Connector UHF, SO-239

LED Meter Indicates relative RF output and received signal

strength

TransmiTTer

Power Output 4 Watts

Modulation Class B amplitude modulation

Freq. Response 300-2500 Hz

Output Impedance 50 ohms, unbalanced

receiver

Sensitivity 0.5μV for 10 dB; (S + N) /N typical (limit 1.0μV)

Selectivity 6 dB @ 7kHz, 70 dB @ 10kHz typical

Image Rejection 80 dB typical

I.F. Frequency Double Conversion Superheterodyne

1st 10.692 MHz

2nd 450 kHz

Automatic Gain

Control (AGC)

less than 10dB change in audio output for inputs from

10 to 50,000 microvolts

Squelch Adjustable; threshold less than1μV

Audio Output Power 7 watts max. into 8 ohms

Freq. Response 300 to 2000 Hz

Distortion less than 10% at 4 watts, 1000Hz

Internal Speaker 16 ohms, 5 watts round

Specications and features are subject to change without notice.

Sheet 2

FCC PART 15 & IC COMPLIANCE INFORMATION

FCC Compliance

This device complies with Part 15 of the FCC rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including

interference that may cause undesired operation.

Changes or modications not expressly approved by the party responsible for

compliance could void your authority to operate the equipment.

Avis de conformité à la FCC : Ce dispositif a été testé et s’avère conforme à

l’article 15 des règlements de la Commission fédérale des communications

(FCC). Ce dispositif est soumis aux conditions suivantes: 1) Ce dispositif

ne doit pas causer d’interférences nuisibles et; 2) Il doit pouvoir supporter

les parasites qu’il reçoit, incluant les parasites pouvant nuire à son

fonctionnement.

Tout changement ou modication non approuvé expressément par la partie

responsable pourrait annuler le droit à l’utilisateur de faire fonctionner cet

équipement.

IC Compliance

This device complies with Industry Canada license-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not

cause interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the device.

Changes or modications not expressly approved by the party responsible for

compliance could void your authority to operate the equipment.

Cet appareil est conforme aux normes RSS exemptes de licences d’Industrie

Canada. Son fonctionnement est soumis aux deux conditions suivantes : (1)

cet appareil ne doit pas causer d’interférences nuisibles et (2), il doit pouvoir

accepter les interférences, incluant celles pouvant nuire à son fonctionnement

normal.

Tout changement ou modication non approuvé expressément par la partie

responsable pourrait annuler le droit à l’utilisateur de faire fonctionner cet

équipement.

ONE-YEAR LIMITED WARRANTY

WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”)

ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail

owner, this Uniden Product to be free from defects in materials and craftsmanship with

only the limitations or exclusions set out below.

Sheet 2

WARRANTY DURATION: This warranty to the original user shall terminate and be

of no further effect 12 months after the date of original retail sale. The warranty is

invalid if the Product is (A) damaged or not maintained as reasonable or necessary,

(B) modied, altered, or used as part of any conversion kits, subassemblies, or any

congurations not sold by Uniden, (C) improperly installed, (D) serviced or repaired by

someone other than an authorized Uniden service center for a defect or malfunction

covered by this warranty, (E) used in any conjunction with equipment or parts or as part

of any system not manufactured by Uniden, or (F) installed or programmed by anyone

other than as detailed by the owner’s manual for this product.

STATEMENT OF REMEDY: In the event that the product does not conform to this

warranty at any time while this warranty is in effect, warrantor will either, at its option,

repair or replace the defective unit and return it to you without charge for parts,

service, or any other cost (except shipping and handling) incurred by warrantor or

its representatives in connection with the performance of this warranty. Warrantor,

at its option, may replace the unit with a new or refurbished unit. THE LIMITED

WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE WARRANTY

PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL

OTHER WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER EXPRESS,

IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING, BUT NOT LIMITED

TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR PROVIDE FOR

THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL

DAMAGES. Some states do not allow this exclusion or limitation of incidental or

consequential damages so the above limitation or exclusion may not apply to you.

LEGAL REMEDIES: This warranty gives you specic legal rights, and you may also

have other rights which vary from state to state. This warranty is void outside the United

States of America.

PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following

the instructions in the owner’s manual you are certain that the Product is defective,

pack the Product carefully (preferably in its original packaging). The Product should

include all parts and accessories originally packaged with the Product. Include

evidence of original purchase and a note describing the defect that has caused you

to return it. The product should be shipped freight prepaid, by traceable means, to

warrantor at:

Uniden America Service

C/O Saddle Creek

743 Henrietta Creek Rd., Suite 100

Roanoke, TX 76262

Sheet 2

Uniden PRO510 XL Le manuel du propriétaire

Marque: Uniden

Modèle: PRO510 XL

Taper: Le manuel du propriétaire

Ce manuel convient également à

PRO510XL

Télécharger le PDF

rapport

dans d''autres langues

English: Uniden PRO510 XL Owner's manual

Uniden PRO510 XL Le manuel du propriétaire

Ce manuel convient également à

Uniden PRO510 XL Le manuel du propriétaire

dans d''autres langues

Documents connexes