Stanley SM18 Manuel utilisateur

ENGLISH (Original Instructions)

SM18

English

French

Russian

Ukrainian

Turkish

ةيبرعلا

14

27

42

61

77

107

ENGLISH (Original Instructions)

2

0000 00-00

a

l

w

ggg

q

mm

cc

aa

p

c

j

ee

dt

e

f

v

u

b

x

o

n

aaa

m

ddd

r

g

k

s

i

ii

bbb

ccc

1

2

3

ENGLISH (Original Instructions)

ii

ff

ee

3

4

ENGLISH (Original Instructions)

4

i

mm

o

j

7

5

6

5

ENGLISH (Original Instructions)

i

nn

pp

v

s

t

e

oo

rr

uu

x

ll

nn

kk

bb

8

9 10

11

ENGLISH (Original Instructions)

6

tt

i

tt

oo

s

v

cc

p

xx

q

yy

ww

cc

12

13 14

15 16

7

ENGLISH (Original Instructions)

v

k

zz

aa

ww

>30mm

ggg

q

yy

xx

17

19

18

20

21 22

ss

hhh

ENGLISH (Original Instructions)

8

dd

bb

c

v

y

I

23

25

26

24

9

ENGLISH (Original Instructions)

ee

ii

h

p

fff

27

28

ENGLISH (Original Instructions)

10

qq

gg

qq

29

11

ENGLISH (Original Instructions)

30

ENGLISH (Original Instructions)

12

31

32

34

35

33

13

ENGLISH (Original Instructions)

36

37

ENGLISH (Original Instructions)

14

INTENDED USE

Your STANLEY Mitre Saw SM18 has been designed for

cutting wood and aluminum, wood products, aluminum

products and plastics. It performs the sawing operations of

cross-cutting, bevelling and mitring easily, accurately and

safely. This tool is intended for professional use.

SAFETY INSTRUCTIONS

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to

these symbols.

DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in

death or serious injury.

WARNING: Indicates a potentially hazardous

situation which, if not avoided, could result in

death or serious injury.

CAUTION: Indicates a potentially hazardous

situation which, if not avoided, may result in

minor or moderate injury.

NOTICE: Indicates a practice not related to personal injury

which, if not avoided, may result in property damage.

Denotes risk of electric shock.

Denotes risk of fire.

Warning: To reduce the risk of injury, read the

instruction manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings, instruc-

tions, illustrations and specifications pro-

vided with this power tool. Failure to follow all

instructions listed below may result in electric

shock, fire and/or serious injury.

Save all warnings and instructions for future

reference

The term “power tool” in the warnings refers to your

mains-operated (corded) power tool or battery operated

(cordless) power tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

b. Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or fumes.

c. Keep children and bystanders away while

operating a power tool. Distractions can cause you

to lose control.

2. Electrical Safety

a. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk

of electric shock.

b. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

c. Do not expose power tools to rain or wet

conditions. Water entering a power tool will increase

the risk of electric shock.

d. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase

the risk of electric shock.

e. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electric shock.

f. If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electric shock.

3. Personal Safety

a. Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools may

result in serious personal injury.

b. Use personal protective equipment. Always wear

eye protection. Protective equipment such as a dust

mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personal injuries.

c. Prevent unintentional starting. Ensure the switch

is in the off position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energising power tools that have the switch

on invites accidents.

d. Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result

in personal injury.

e. Do not overreach. Keep proper footing and

balance at all times. This enables better control of

the power tool in unexpected situations.

f. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away from

moving parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

g. If devices are provided for the connection of dust

extraction and collection facilities, ensure these

are connected and properly used. Use of dust

collection can reduce dust-related hazards.

h. Do not let familiarity gained from frequent use of

tools allow you to become complacent and ignore

tool safety principles. A careless action can cause

severe injury within a fraction of a second.

15

ENGLISH (Original Instructions)

4. Power Tool Use And Care

a. Do not force the power tool. Use the correct power

tool for your application. The correct power tool will

do the job better and safer at the rate for which it was

designed.

b. Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be

repaired.

c. Disconnect the plug from the power source and/

or remove the battery pack, if detachable from

the power tool before making any adjustments,

changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d. Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands

of untrained users.

e. Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition that

may affect the power tool’s operation. If damaged,

have the power tool repaired before use. Many

accidents are caused by poorly maintained power

tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to

be performed. Use of the power tool for operations

different from those intended could result in a

hazardous situation.

h. Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and

control of the tool in unexpected situations.

5. Service

a. Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power tool

is maintained.

SAFETY INSTRUCTIONS FOR MITRE SAWS

♦ Mitre saws are intended to cut wood or wood-like

products, they cannot be used with abrasive cut-

off wheels for cutting ferrous material such as

bars, rods, studs, etc. Abrasive dust causes moving

parts such as the lower guard to jam. Sparks from

abrasive cutting will burn the lower guard, the kerf

insert and other plastic parts.

♦ Use clamps to support the workpiece

wheneverpossible. If supporting the workpiece

by hand, you must always keep your hand at least

100 mm from either side of the saw blade. Do not

use this saw to cut pieces that are too small to be

securely clamped or held by hand. If your hand is

placed too close to the saw blade,there is an increased

risk of injury from blade contact.

♦ The workpiece must be stationary and clamped or

held against both the fence and the table. Do not

feed the workpiece into the blade or cut “freehand”

in any way. Unrestrained or moving workpieces could

be thrown at high speeds,causing injury.

♦ Push the saw through the workpiece. Do not

pull the saw through the workpiece. To make a

cut, raise the saw head and pull it out over the

workpiece without cutting, start the motor, press

the saw head down and push the saw through

the workpiece. Cutting on the pull stroke is likely to

cause the saw blade to climb on top of the workpiece

and violently throw the blade assembly towards the

operator.

♦ Never cross your hand over the intended line of

cutting either in front or behind the saw blade.

Supporting the workpiece “cross handed” i.e. holding

the workpiece to the right of the saw blade with your

left hand or vice versa is very dangerous.

♦ Do not reach behind the fence with either hand

closer than 100 mm from either side of the saw

blade, to remove wood scraps, or for any other

reason while the blade is spinning. The proximity

of the spinning saw blade to your hand may not be

obvious and you may be seriously injured.

♦ Inspect your workpiece before cutting. If the

workpiece is bowed or warped, clamp it with the

outside bowed face toward the fence. Always

make certain that there is no gap between the

workpiece, fence and table along the line of the

cut. Bent or warped workpieces can twist or shift and

may cause binding on the spinning saw blade while

cutting. There should be no nails or foreign objects in

the workpiece.

♦ Do not use the saw until the table is clear of all

tools, wood scraps, etc., except for the workpiece.

Small debris or loose pieces of wood or other objects

that contact the revolving blade can be thrown with

high speed.

♦ Cut only one workpiece at a time. Stacked multiple

workpieces cannot be adequately clamped or braced

and may bind on the blade or shift during cutting.

♦ Ensure the mitre saw is mounted or placed on

a level, firm work surface before use.A level and

firm work surface reduces the risk of the mitre saw

becoming unstable.

♦ Plan your work. Every time you change the bevel

or mitre angle setting, make sure the adjustable

fence is set correctly to support the workpiece

and will not interfere with the blade or the

guarding system. Without turning the tool “ON” and

with no workpiece on the table, move the saw blade

through a complete simulated cut to assure there will

be no interference or danger of cutting the fence.

♦ Provide adequate support such as table

extensions, saw horses, etc. for a workpiece that

is wider or longer than the table top. Workpieces

longer or wider than the mitre saw table can tip if not

securely supported. If the cut-off piece or workpiece

ENGLISH (Original Instructions)

16

tips, it can lift the lower guard or be thrown by the

spinning blade.

♦ Do not use another person as a substitute for a

table extension or as additional support. Unstable

support for the workpiece can cause the blade to bind

or the workpiece to shift during the cutting operation

pulling you and the helper into the spinning blade.

♦ Thecut-offpiecemustnotbejammedorpressed

byanymeansagainstthe spinning saw blade. If

confined, i.e. using length stops, the cut-off piece could

get wedged against the blade and thrown violentiy.

♦ Always use aclamp or a fixture designed to

properly support round material such as rods or

tubing. Rods have a tendency to roll while being cut,

causing the blade to “bite” and pull the work with your

hand into the blade.

♦ Let the blade reach full speed before contacting

the workpiece. This will reduce the risk of the

workpiece being thrown.

♦ If the workpiece or blade becomes jammed, turn

the mitre saw off.Wait for all moving parts to stop

and disconnect the plug from the power source

and/ or remove the battery pack. Then work to

free the jammed material. Continued sawing with

a jammed workpiece could cause loss of control or

damage to the mitre saw.

♦ After finishing the cut, release the switch, hold

the saw head down and wait for the blade to stop

before removing the cut-off piece. Reaching with

your hand near the coasting blade is dangerous.

♦ Hold the handle firmly when making an incomplete

cut or when releasing the switch before the saw

head is completely in the down position. The

braking action of the saw may cause the saw head to

be suddenly pulled downward, causing a risk of injury.

ADDITIONAL SAFETY RULES FOR MITRE

SAWS

♦ The machine is provided with a special configured

power supply cord which can only be replaced by the

manufacturer or its authorised service agent.

♦ Do not use the saw to cut other materials than those

recommended by the manufacturer.

♦ Cutting plastics, sap coated wood, and other materials

may cause melted material to accumulate on the blade

tips and the body of the saw blade, increasing the risk

of blade overheating and binding while cutting.

♦ Do not operate the machine without guards in posi-

tion, or if guards do not function or are not maintained

properly.

♦ Ensure that the arm is securely fixed when performing

bevel cuts.

♦ Keep the floor area around the machine level,

well-maintained and free of loose materials, e.g., chips

and cut-offs.

♦ Use correctly sharpened saw blades. Observe the

maximum speed mark on the saw blade.

♦ Make sure all locking knobs and clamp handles are

tight before starting any operation.

♦ Never place either hand in the blade area when the

saw is connected to the electrical power source.

♦ Never attempt to stop a machine in motion rapidly by

jamming a tool or other means against the blade; seri-

ous accidents can occur.

♦ Before using any accessory consult the instruction

manual. The improper use of an accessory can cause

damage.

♦ Use a holder or wear gloves when handling a saw

blade.

♦ Ensure that the saw blade is mounted correctly before

use.

♦ Make sure that the blade rotates in the correct

direction.

♦ Take care when slotting.

♦ Do not use blades of larger or smaller diameter than

recommended. For the proper blade rating refer to the

technical data. Use only the blades specified in this

manual, complying with EN 847-1.

♦ Consider applying specially designed noise-reduction

blades.

♦ Do not use HSS blades.

♦ Do not use cracked or damaged saw blades.

♦ Do not use any abrasive or diamond discs.

♦ Never use your saw without the kerf plate.

♦ Raise the blade from the kerf in the workpiece prior to

releasing the switch.

♦ Do not wedge anything against the fan to hold the

motor shaft.

♦ The blade guard on your saw will automatically raise

when the arm is brought down; it will lower over the

blade when head lock up release lever (cc) is pushed.

♦ Never raise the blade guard manually unless the saw

is switched off. The guard can be raised by hand when

installing or removing saw blades or for inspection of

the saw.

♦ Check periodically that the motor air slots are clean

and free of chips.

♦ Replace the kerf plate when worn. Refer to service

parts list included.

♦ Disconnect the machine from the mains before

carrying out any maintenance work or when changing

the blade.

♦ Never perform any cleaning or maintenance work

when the machine is still running and the head is not

in the rest position.

♦ When possible, always mount the machine to a bench.

♦ The front section of the guard is louvered for visibility

while cutting. Although the louvers dramatically

reduce flying debris, they are openings in the guard

and safety glasses should be worn at all times when

viewing through the louvers.

♦ Connect the saw to a dust collection device when

sawing wood. Always consider factors which influence

exposure of dust such as:

– type of material to be machined (chip board

produces more dust than wood);

17

ENGLISH (Original Instructions)

– sharpness of the saw blade;

– correct adjustment of the saw blade,

– dust extractor with air velocity not less than 20 m/s.

Ensure that the local extraction as well as hoods, baffles

and chutes are properly adjusted.

♦ Please be aware of the following factors influencing

exposure to noise:

– use saw blades designed to reduce the emitted

noise;

– use only well sharpened saw blades;

♦ Machine maintenance shall be conducted periodically;

♦ Machine faults, including guards or saw blade, shall be

reported as soon as they are discovered;

♦ Provide adequate general or localized lighting;

♦ Ensure the operator is adequately trained in the use,

adjustment and operation of the machine;

♦ Ensure that any spacers and spindle rings are suitable

for the purpose as stated in this manual.

♦ Refrain from removing any cut-offs or other parts of

the workpiece from the cutting area while the machine

is running and the saw head is not in the rest position

♦ Never cut workpieces shorter than 30 mm(Figure 34).

♦ Without additional support the machine is designed to

accept the maximum workpiece size of:

– Height 75 mm by width 140 mm by length 460 mm

– Longer workpieces need to be supported by suit-

able additional table(work support). Always clamp

the workpiece safely.

♦ In case of an accident or machine failure, immediately

turn the machine off and disconnect machine from the

power source.

♦ Report the failure and mark the machine in suitable

form to prevent other people from using the defective

machine.

♦ When the saw blade is blocked due to abnormal feed

force during cutting, turn the machine off and discon-

nect it from power supply. Remove the workpiece and

ensure that the saw blade runs free. Turn the machine

on and start new cutting operation with reduced feed

force.

♦ Never cut light alloy, especially magnesium.

♦ Whenever the situation allows, mount the machine to

a bench using bolts.

RESIDUAL RISKS

The following risks are inherent to the use of saws:

– injuries caused by touching the rotating parts

In spite of the application of the relevant safety reg-

ulations and the implementation of safety devices,

certain residual risks cannot be avoided. These are:

– Impairment of hearing.

– Risk of accidents caused by the uncovered parts of the

rotating saw blade.

– Risk of injury when changing the blade.

– Risk of squeezing fingers when opening the guards.

– Health hazards caused by breathing dust developed

when sawing wood, especially oak, beech and MDF.

The following factors increase the risk of breathing

problems:

– No dust extractor connected when sawing wood.

– Insufficient dust extraction caused by uncleaned exhaust

filters.

ELECTRICAL SAFETY

Only one voltage is applicable to this tool. Be sure to check

that the power supply corresponds to the voltage on the

rating plate.

Your Stanley tool is equipped with double insula-

tion, hence, it does not require to be earthed

When the power cord is damaged, have it sent

to a STANLEY service center for replacement to specially

prepared cables.

USING AN EXTENSION CABLE

If an extension cable is required, use an approved 3–core

extension cable suitable for the power input of this tool

(see Technical Data).The minimum conductor size is 1.5

mm

2

; the maximum length is 30 m. When using a cable

reel, always unwind the cable completely.

Cable cross-sectional

area (mm

2

)

Cable rated current

(Ampere)

0.75 6

1.00 10

1.50 15

2.50 20

4.00 25

Cable length (m)

7.5 15 25 30 45 60

Voltage Amperes Cable rated current (Ampere)

110~127 0 - 2.0 6 6 6 6 6 10

2.1 - 3.4 6 6 6 6 15 15

3.5 - 5.0 6 6 10 15 20 20

5.1 - 7.0 10 10 15 20 20 25

7.1 - 12.0 15 15 20 25 25 -

12.1 - 20.0 20 20 25 - - -

230 0 - 2.0 6 6 6 6 6 6

2.1 - 3.4 6 6 6 6 6 6

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 -

ENGLISH (Original Instructions)

18

LABELS ON TOOL

In addition to the pictographs used in this manual, the

labels on the tool show the following pictographs:

WARNING! To reduce the risk of injury, the user

must read the instruction manual before use.

Wear a dust mask.

Wear ear protection.

Wear safety glasses or goggles.

Keep your hands away from this area

V Volts

Direct Current

A Amperes n

0

No-Load Speed

Hz Hertz

Class II Construction

WWatts

Earthing Terminal

min minutes

Safety Alert Symbol

Alternating

Current

/min.

Revolutions or

Reciprocation per

minute

Date Code Position (Fig. 1)

The Date Code, which also includes the year of

manufacture, is printed into the housing.

Example: 2019 XX XX

Year of Manufacture

THE PACKAGE CONTAINS

1 Mitre Saw

1 Blade wrench stored in wrench pocket

1 Saw blade

1 Dust bag

1 Vertical clamp

1 Rear support

1 Instruction manual

♦ Check for damage to the tool, parts or accessories

which may have occurred during transport.

♦ Take the time to thoroughly read and understand this

manual prior to operation.

Description (Fig. 1, 2, 3, 5, 6, 12, 23, 27, 28)

WARNING: Never modify the power tool or any

part of it. Damage or personal injury could result.

a. Operating handle

b. Lower guard

c. Right side, fence

d. Table

e. Mitre lock knob

f. Mitre scale

g. Base

h. Extension knob

i. Wrench

j. Bench mounting holes

k. Fence clamping knob

l. Trigger switch

m. Carrying handle

n. Dust spout

o. Lock down pin

p. Bevel clamp knob

q. Bevel scale

r. Hand indentation

s. Kerf plate

t. Mitre detent

u. Date code

v. Left side, fence

w. End cap

x. Spindle lock

y. Hole for padlock

z. Angle position stop

aa. Bevel position adjustment stop

bb. LED switch

cc. Vertical position adjustment stop

dd. Lock-off lever

ee. Length stop

ff. Dust bag

gg. Vertical clamp

ii. Work support

jj. Fence stop screw

mm. Rear support

aaa. Rear handle

bbb. Mitre arm support

ccc. Work support clamping knob

ddd. Rail lock knob

fff. Bevel lock knob

ggg. Slide stop control

ASSEMBLY AND ADJUSTMENT

WARNING: To reduce the risk of injury, turn unit

off and disconnect machine from power source

before installing and removing accessories,

before adjusting or changing set-ups or when

making repairs. Be sure the trigger switch is in the OFF

position. An accidental start-up can cause injury.

19

ENGLISH (Original Instructions)

3. Remove the blade locking screw (nn) and the outside

arbor collar (pp).

4. Install the saw blade (oo) onto the blade adaptor (uu)

seated directly against the inside arbor collar (rr), mak-

ing sure that the teeth at the bottom edge of the blade

are pointing toward the back of the saw (away from the

operator).

5. Replace the outer arbor collar (pp).

6. Tighten the blade locking screw (nn) carefully by turn-

ing counter-clockwise while holding the spindle lock

engaged with your other hand.

7. Return the guard bracket (ll) to its original position and

firmly tighten the guard bracket screw (kk) to hold brack-

et in place.

WARNING! Be aware the saw blade shall be

replaced in the described way only. Only use

saw blades as specified under Technical Data.

WARNING! The guard bracket(ll) must be

returned to its original position and the guard

bracket screw(kk) tightened before activating the

saw.

WARNING! Failure to do so may allow the guard

to contact the spinning saw blade resulting in

damage to the saw and severe personal injury.

Your mitre saw was accurately adjusted at the factory. If

readjustment due to shipping and handling or any other

reason is required, follow the steps below to adjust your

saw. Once made, these adjustments should remain

accurate.

Checking and Adjusting the Mitre Scale

(Fig. 11, 12, 13)

1. Loosen the mitre lock knob (e), depress the mitre detent

(t) to release the mitre arm. Swing the mitre arm until the

latch locates it at the 0° mitre position. Do not lock mitre

lock knob (e).

2. Pull down the head until the blade just enters the saw

kerf (s).

3. Place a square (tt) against the left side fence (v) and

blade (oo) (Fig. 11).

WARNING: Do not touch the tips of the blade

teeth with the square.

If adjustment is required, proceed as follows:

4. Tighten the mitre lock knob (e). Loose the fence clamp-

ing knob (k), remove the left side fence (v) and right side

fence (c).

5. Loose 4 hex bolts behind the fence, adjust the base

fence as the necessary to against the square (tt).

6. Tighten the hex bolts, and install the side fence.the

wrench (i) to tighten the hex bolts on the fence in the

order from the right side.

Unpacking (Fig. 2, 4, 5, 6)

♦ Remove the saw from the packing material carefully

using the carrying handle (m) and rear handle(aaa).

♦ Use the supplied blade wrench(i) to mount the rear

support (mm) to the back of base(g).

♦ Press down the operating handle (a) and pull out the

lock down pin (o), as shown.

♦ Gently release the downward pressure and allow the

arm to rise to its full height.

Bench Mounting (Fig. 7)

♦ Holes (j) are provided in all four feet to facilitate bench

mounting. Always mount your saw firmly to prevent

movement. To enhance the portability, the tool can be

mounted to a piece of 15 mm or thinner plywood which

can then be clamped to your work support or moved to

other job sites and reclamped.

♦ When mounting your saw to a piece of ply-

wood, make sure that the mounting screws

do not protrude from the bottom of the wood.

The plywood must sit flush on the work support. When

clamping the saw to any work surface, clamp only on

the clamping bosses where the mounting screw holes

are located. Clamping at any other point will interfere

with the proper operation of the saw.

♦ To prevent binding and inaccuracy, be sure the moun-

ting surface is not warped or otherwise uneven. If the

saw rocks on the surface, place a thin piece of material

under one saw foot until the saw is firm on the moun-

ting surface.

Mounting the Saw Blade (Fig. 8, 9, 10)

WARNING: To reduce the risk of injury, turn unit

off and disconnect machine from power source

before installing and removing accessories,

before adjusting or changing set-ups or when

making repairs. Be sure the trigger switch is in the OFF

position. An accidental start-up can cause injury.

♦ Never depress the spindle lock button while the blade

is under power or coasting.

♦ Do not cut light alloy and ferrous metal (containing iron

or steel) or masonry or fibre cement product with this mitre

saw.

♦ Should use the corresponding blade cutting different

materials.

1. With the lower guard held in the raised position loosen

the guard bracket screw (kk) until the guard bracket (ll)

raises far enough to access the blade locking screw

(nn).

2. Depress the spindle lock button (x) with one hand and

with the other hand use the wrench (i) provided to

loosen the left-hand threaded blade locking screw (nn)

by turning clockwise.

WARNING: To use the spindle lock, press the

button as shown and rotate the spindle by hand

until you feel the lock engage.

Continue to hold the lock button in to keep the spindle from

turning.

ENGLISH (Original Instructions)

20

5. To achieve a 0° or a 45° right/left bevel, the three adjust-

ment stop screws must be adjusted to allow the saw arm

to move as necessary.

Adjusting the Depth Stop (Sawing Grooves)

(Fig.20)

This operation is necessary if you want to saw a groove.

– Move the depth stop plate (hhh) to the place as shown

Fig 20.

– Tilt the tool head by the handle to the position at which the

requested groove depth is reached.

– Turn the adjusting screw(ss) clockwise until the end of the

screw touches the housing stop.

– Guide the tool arm slowly upward.

Return the depth stop plate (hhh) to its original position

once sawing grooves done.

Ensure that saw blades do not touch any part of the base

or kerf plate.

Guard Actuation and Visibility

The blade guard on your saw has been designed to automat-

ically raise when the arm is brought down and to lower over

the blade when the arm is raised.

The guard can be raised by hand when installing or removing

saw blades or for inspection of the saw. NEVER RAISE

THE BLADE GUARD MANUALLY UNLESS THE SAW IS

TURNED OFF.

NOTE: Certain special cuts will require that you manually

raise the guard. The front section of the guard is louvered

for visibility while cutting. Although the louvers dramatically

reduce flying debris, they are openings in the guard and

safety glasses should be worn at all times when viewing

through the louvers.

Automatic Electric Brake

Your saw is equipped with an automatic electric blade brake

which stops the saw blade within 10 seconds of trigger

release. This is not adjustable.

On occasion, there may be a delay after trigger release to

brake engagement. On rare occasions, the brake may not

engage at all and the blade will coast to a stop.

If a delay or “skipping” occurs, turn the saw on and off 4 or 5

times. If the condition persists, have the tool serviced by an

authorized STANLEY service center.

Always be sure the blade has stopped before removing it from

the kerf. The brake is not a substitute for guards or for ensur-

ing your own safety by giving the saw your complete attention.

Kerf Plate Adjustment

To adjust the kerf plates, loosen the screws holding the

kerf plates in place. Adjust the kerf plates are as close

as possible without interfering with the blade’s movement.

Brushes (Fig. 1)

WARNING: To reduce the risk of serious person-

al injury, turn off the tool and disconnect it from

the power source before attempting to move it,

change accessories or make any adjustments.

Inspect carbon brushes regularly by unplugging the

tool, removing the Brush holder cap (W) that holds the

Checking and Adjusting the Blade to the Table

(Fig. 14, 15, 16)

1. Loosen the bevel clamp knob (p).

2. Press the mitre arm to the right to ensure it is fully

vertical with the angle position stop located against the

vertical position adjustment stop (cc) and tighten the

bevel clamp knob.

3. Pull down the head until the blade just enters the saw

kerf (s).

4. Place a set square (tt) on the table and up against

the blade (oo) (Fig. 15).

WARNING: Do not touch the tips of the blade

teeth with the square.

If adjustment is required, proceed as follows:

5. Loosen the lock nut (ww) a few turns and turn the bevel

position adjustment stop screw (cc) in or out until the

pointer (xx) indicates 45°-0° with the angle position stop

resting on the bevel position adjustment stop.

6. Firmly tighten the lock nut (ww) while holding the stop

screw(cc) stationary.

7. If the bevel pointer (xx) does not indicate zero on the

bevel scale (q), loosen the screw (yy) that secures the

pointer and move the pointer as necessary

Adjusting the Fence (Fig. 17)

The upper part of the fence can be adjusted to provide

clearance, allowing the saw to bevel to 45° left and 0° right.

To adjust the left fence (v) and right side fence(c):

1. Loosen the plastic knob (k) and slide the fence to the left.

2. Make a no load running with the saw switched off and

check for clearance. Adjust the fence to be as close to

the blade as practical to provide maximum workpiece

support, without interfering with the up and down move-

ment of the arm.

3. Tighten the knob securely.

WARNING: The guide grooves (zz) can become

clogged with sawdust. Use a stick or some low

pressure air to clear the guide grooves.

Checking and Adjusting the Bevel Angle

(Fig. 17, 18, 19)

1. Loosen the left side fence clamping knob (k) and slide

the upper part of the left side fence to the left as far as it

will go.

2. Loosen the bevel clamp knob (p) and move the saw arm

to the left 45° bevel position

If adjustment is required, proceed as follows:

3. Loosen the locknut (ww) a few turns and turn the bevel

position adjustment stop screw (aa) in or out until the

pointer (xx) indicates 45° with the angle position stop (z)

resting on the bevel position adjustment stop.

4. Firmly tighten the lock nut (ww) while holding the stop

screw (aa) stationary.

La page charge ...

Stanley SM18 Manuel utilisateur

Stanley SM18 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents