Danby DDR50B3WP Mode d'emploi

Marque: Danby

Modèle: DDR50B3WP

Catégorie: Déshumidificateurs

Taper: Mode d'emploi

Ce manuel convient également à

DDR45B3WP

DANBY PRODUCTS LIMITED, ONTARIO, CANADA N1H 6Z9

DANBY PRODUCTS INC., FINDLAY, OHIO, USA 45840

2:1(5¶686($1'&$5(*8,'(

*8,'('¶87,/,6$7,21(7'(175(7,(1

*8Ë$'(87,/,=$&,Ï1<&8,'$'23$5$(/3523,(7$5,2

02'(/02'Ê/(02'(/2

)25<2856$)(7<Read these instructions carefully before operating the unit.

32859275(6e&85,7eLire attentivement ces instructions avant d’utiliser l’appareil.

3$5$686(*85,'$'Lea y observe todas las reglas de seguridad y las instrucciones de operación antes

de usar este producto.

(1*/,6+

PORTABLE DEHUMIDIFIER

DESHUMIDIFICATEUR PORTATIF

DESHUMIDIFICADOR PORTÁTIL

DDR30B3WP

DDR45B3WP

DDR50B3WP

2015.05.11

DO NOT RETURN THIS UNIT TO THE RETAILER

WITHOUT FURTHER INSTRUCTIONS

Dear valued customer, we hope your Danby product purchase fulfills all

your requirements. Your satisfaction is our priority!

Please contact us at our toll free consumer service number for any inquiries

you may have about your new unit.

NE PAS RETOURNER CET APPAREIL CHEZ LE

DÉTAILLANT SANS CONSIGNES SUPPLÉMENTAIRES

Cher(ère) client(e) important(e), nous espérons que votre produit Danby

répond à tous vos besoins. Votre satisfaction est notre priorité!

Veuillez nous contacter au numéro gratuit de service après-vente, si

vous avez des questions quelconques à propos de votre nouvel appareil.

NO DEVUELVA ESTA UNIDAD A LA TIENDA SIN

INSTRUCCIONES ADICIONALES

Estimado cliente, esperamos que el producto Danby que ha comprado

satisfaga completamente sus necesidades. Su satisfacción

es nuestra prioridad!

Por favor, contáctenos gratuitamente a nuestro número de Servicio al

Cliente para cualquier pregunta que tenga sobre su nuevo electrodoméstico.

1-800-263-2629

(1-800-26-DANBY)

Danby 28.08.2014

TO OBTAIN WARRANTY SERVICE YOU MUST PROVIDE A VALID PROOF OF

PURCHASE. PLEASE STAPLE YOUR RECEIPT TO THIS PAGE FOR FUTURE

REFERENCE.

POUR OBTENIR LE SERVICE SUR GARANTIE, VOUS DEVEZ FOURNIR UNE

PREUVE D’ACHAT VALIDE. VEUILLEZ AGRAFER VOTRE REÇU À CETTE PAGE

POUR RÉFÉRENCE FUTURE.

PARA OBTENER SERVICIO DE GARANTÍA, DEBE PROVEER UN RECIBO ORIG-

INAL. POR FAVOR ENGRAPE SU RECIBO A ÉSTA PÁGINA EN CASO QUE

NECESITE HACER UN RECLAMO.

This product is factory equipped with a power supply cord that has a three-pronged grounded plug. It must

be plugged into a mating grounding type receptacle in accordance with the National Electrical Code and

applicable local codes and ordinances. If the circuit does not have a grounding type receptacle, it is the

responsibility and obligation of the customer to exchange the existing receptacle in accordance with the

National Electrical Code and applicable local codes and ordinances. The third ground prong should not,

under any circumstances, be cut or removed. Never use the cord, the plug or the appliance when they show

any sign of damage. Do not use your appliance with an extension cord unless it has been checked and test-

ed by a qualiﬁ ed electrician or electrical supplier.

IMPORTANT - GROUNDING METHOD

Ce produit arrive d’origine avec un cordon d’alimentation équipé d’une prise à trois ﬁ ches. Il doit être

branché dans une prise avec une ﬁ che de mise à la terre en conformité avec le Code national de l’électricité

et les codes et règles locaux applicables. Si la prise murale n’a pas de mise à la terre, il est de la

responsabilité et l’obligation du client de changer la prise existante pour la rendre conforme au Code

national de l’électricité et aux codes et règles locaux applicables. La ﬁ che de mise à la terre ne doit pas, en

aucune circonstance, être coupée ou retirée. Si vous apercevez des signes de dommage, n’utilisez jamais le

cordon d’alimentation, la prise ou l’appareil. N’utilisez jamais l’appareil avec une rallonge sauf si elle a été

vériﬁ ée et testée par un électricien qualiﬁ é ou un fournisseur de matériel électrique.

IMPORTANT - MÉTHODE POUR LA MISE À LA TERRE

Este producto viene equipado con un cable eléctrico que tiene un enchufe de tres patas conexión a tierra.

Este debe colocarse en una toma de corriente con conexión a tierra de acuerdo con el Código nacional de

electricidad y códigos y ordenanzas locales correspondientes. Si el circuito no cuenta con una toma de

corriente con conexión a tierra, es responsabilidad y obligación del cliente sustituir la toma de corriente

actual de acuerdo con el Código nacional de electricidad u códigos u ordenanzas locales correspondientes.

Bajo ninguna cicunstancia se debe cortar o eliminar la tercera pata de conexión a tierra. Nunca utilice el

cable, el enchufe o el artefacto cuando muestre un signo de daño visible. No utilice el artefacto con una

extensión salvo que un proveedor eléctrico o electricista caliﬁ cado la inspeccione y la pruebe.

IMPORTANTE- MÉTODO DE CONEXIÓN A TIERRA

PORTABLE DEHUMIDIFIER

Owner’s Use and Care Guide .................................................1-13

• Welcome

• Important Safety Information

• Features

• Installation Instructions

• Operation Instructions

• Care and Maintenance

• Troubleshooting

• Warranty

DÉSHUMIDIFICATEUR PORTATIF

Guide d’utilisation et d’entretien..............................................14-27

• Bienvenue

• Consignes de sécurité importantes

• Caractéristiques

• Consignes d’installation

• Consignes d’utilisation

• Soins et entretien

• Dépannage

• Garantie

DESHUMIDIFICADOR PORTÁTIL

Guía del utilización y cuidado para el propietario...................28-41

• Bienvenido

• Instrucciones de seguridad importantes

• Instrucciones d’instalación

• Características

• Instrucciones operadoras

• Cuidado y maintenimiento

• Solucion sugerida

• Garantía

CONTENTS

CAUTION:

Read and follow all safety rules and operating

instructions before ﬁ rst use of this product.

PRÉCAUTION :

Veuillez lire attentivement les consignes de

sécurité et les instructions d’utilisation avant

l’utilisation initiale de ce produit.

TABLE DES MATIÈRES

ÍNDICE

PRECAUCIÓN:

Veuillez lire attentivement les consignes de

sécurité et les instructions d’utilisation avant

l’utilisation initiale de ce produit.

Model • Modèle • Modelo

DDR30B3WP / DDR45B3WP / DDR50B3WP

WARNING

Improper connection of the grounding plug can

result in risk of ﬁ re, electric shock and/or injury to

persons associated with the appliance. Check with

a qualiﬁ ed service representative if in doubt that

the appliance is properly grounded.

AVERTISSEMENT

Une ﬁ che de mise à la terre mal branchée peut

entraîner un risque d’incendie, de choc électrique

ou de blessures aux personnes qui utilisent

l’appareil. Si vous n’êtes pas certain que l’appareil

est correctement mis à la terre, consultez un

préposé du service qualiﬁ é.

ADVERTENCIA

El conectar indebidamente el enchufe de conexión

a tierra puede crear riesgos de incendio, descarga

eléctrica y/o oscasionar lesiones a las personas

que usen el aparato. Si tiene dudas sobre la

debida conexión a tierra del aparato, consulte un

representante de servicios caliﬁ cado.

Thank you for choosing Danby

We know you’re excited. We are too! However, the more familiar you are with your new appliance, the better experience you will

have. We therefore strongly suggest that you read this Owner’s Manual before plugging in your new appliance. It contains

important operational information that will help you make full use of the technical features available in your Danby appliance. The

manual also contains information designed to enhance operating reliability and safety, as well as tips to maintaining your new

appliance so that it brings you happiness for years to come.

Please visit www.danby.com to access self-service tools, FAQs and more. Should you need additional assistance, please call

1-800-26-DANBY (1-800-263-2629).

Note: You will need the below information to obtain service under warranty.

To receive service, you must provide the original receipt.

Model Number:

Serial Number:

Date of Purchase:

NEED HELP?

Before you call for service, here are a few things you can do to help us serve you

better:

Read this Owner’s Manual:

It contains instructions to help you use and maintain your appliance properly.

If you received a damaged appliance:

Immediately contact the retailer (or builder) that sold you the appliance.

Save time and money:

Check the Troubleshooting section at the end of the guide before calling. This section

helps you solve common problems that may occur.

If you do need service, you can relax, knowing help is only a phone call away.

Tel: 1-800-26-

(1-800-263-2629)

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

NOTE

The WARNING instructions issued in this manual are not meant to cover all possible conditions and situations that may

occur. Person(s) installing, maintaining, or operating the appliance must exercise caution and care. Failure to install,

maintain, and/or operate the equipment according to the manufacturer’s instructions may result in conditions which can

produce personal injury and damage to your unit and/or property damage. Contact your dealer, service agent, and/or the

manufacturer about any problems or conditions you do not fully understand. For Danby Consumer Service call (1-800-

263-2629).

To reduce the risk of ﬁ re, electric shock, or personal injury, all wiring and grounding must conform with the latest edition of

Local and National Electrical codes.

• It is the customer’s responsibility to have the wiring and fuses checked by a qualiﬁ ed electrician to make sure adequate

electrical power is available.

• This appliance is designed to operate on an effectively grounded, separately branched, polarized, 3-wire, 120 Volt

60 Hertz (alternating current) circuit protected by a 15 ampere fuse, equivalent fuse or circuit breaker. The three-prong

grounding plug on the power cord should be plugged directly into the aforementioned receptacle rated 110/120 V.A.C.

• Do not connect the dehumidiﬁ er to a multiple socket outlet that is also being used for other electrical appliances.

FOR YOUR SAFETY: To reduce the risk of ﬁ re or explosion, do not store or use gasoline or other ﬂ ammable va-

pors or liquids in the vicinity of this or any other appliance.

ELECTRICAL REQUIREMENTS

Improper connection of the equipment-grounding conductor can result in a risk of electrical shock. Check with a qualiﬁ ed

electrician or serviceperson if you are in doubt as to whether your appliance outlets are properly grounded.

• This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electrical

shock by providing a path of least resistance for electrical current. This appliance is equipped with a cord that has an

equipment-grounding conductor and 3 prong grounding plug. The plug must be connected into an outlet that is properly

installed and grounded in accordance with all local codes and ordinances.

• Do not modify the plug provided with this appliance. If it will not ﬁ t the outlet, have a proper outlet installed by a qualiﬁ ed

electrician.

• If the household electrical supply does not meet the above speciﬁ cations, or if you are not sure your home has an

effective ground, have a qualiﬁ ed electrician or your local electrical utility company check it and correct any problems.

SAVE THESE INSTRUCTIONS

GROUNDING INSTRUCTIONS

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAFETY PRECAUTIONS

When using this dehumidiﬁ er, always follow basic safety precautions, including the following:

• Use this appliance only for its intended purpose as described in this Owner’s Manual.

• Do not remove the Styrofoam in the ﬂ oat which is located in the bucket.

• This dehumidiﬁ er must be properly installed and grounded as described in this manual before it is used.

• Never operate this dehumidiﬁ er in an area that is likely to accumulate standing water. If this condition develops, for your

safety disconnect the power supply before stepping into the water.

• Never unplug your dehumidiﬁ er by pulling on the power cord. Always grip the plug ﬁ rmly and pull straight out from the

receptacle.

• Replace immediately all electric service cords that have become frayed or otherwise damaged. A damaged power

supply cord must be replaced with a new power supply cord obtained from the manufacturer and not repaired. Do not

use a cord that shows cracks or abrasion damage along its length or at either the plug or connector end.

• If the receptacle does not match the plug, the receptacle must be changed out by a qualiﬁ ed electrician.

• Turn the dehumidiﬁ er OFF and unplug it before cleaning.

• For your safety, do not store or use combustible materials, gasoline or other ﬂ ammable vapors or liquids in the vicinity of

this or any other appliance.

• All dehumidiﬁ ers contain refrigerants, which under federal law must be removed prior to product disposal. If you are

disposing of a product with refrigerants, check with the company handling disposal about what to do. Check for

local regulatory compliance regarding the approved and safe disposal of this appliance.

• Do not use outdoors.

• This dehumidiﬁ er is intended for indoor residential applications only. This dehumidiﬁ er should not be used

for commercial or industrial applications.

SAVE THESE INSTRUCTIONS

Installation Instructions

• Select a suitable location, making sure you have easy access to an electrical outlet (avoid the use of extension cords).

• Make sure there are no obstructions restricting airﬂ ow through the front air intake grill. Maintain a minimum clearance

of at least 20 cm (8”) between adjacent walls and the back of the unit, to allow for proper air circulation and maximum

efﬁ ciency. To achieve maximum operating efﬁ ciency from your dehumidiﬁ er, the recommended (room ambient) operating

temperatures should be between 5°C (41°F) and 35°C (95°F).

• It is important to remember the efﬁ ciency of a dehumidiﬁ er will be affected/inﬂ uenced by the rate at which new humid

air (moisture) is allowed to inﬁ ltrate the same space/area. To maintain efﬁ ciency, the dehumidiﬁ er must be operated in an

enclosed area. Keep all doors and windows closed.

• Do not use this unit outdoors. This dehumidifer is intended for indoor residential applications only. This dehumidiﬁ er

should not be used for commercial or industrial applications.

• Place the dehumidiﬁ er on a smooth, level ﬂ oor strong enough to support the unit with a full bucket of water.

• Place the unit where it has access to an electrical outlet.

• This unit has 4 castors which can move freely. Do not force castors to move over carpet, and refrain from moving the

unit with water in the bucket (the unit may tip over and spill water). Protect wood ﬂ oors from possible spillage or

scratches when moving unit.

• Remove accessory bag from bucket and store it in a safe place.

LOCATION

FEATURES

1. Control Panel

2. Front Panel

3. Water Bucket

4. Water Level Window

5. Carrying Handle (both sides)

6. Continuous Drain Hose Outlet

7. Air Outlet Grill

8. Air Filter

9. Power Cord Buckle

10. Caster

11. Power Cord and Plug

Operating Instructions

NOTE: The control panel of the unit you purchased may be slightly different depending on the model number.

CONTROL PANEL INSTRUCTIONS

CASTOR INSTALLATION (some models)

Castor installation is recommended to avoid damage to ﬂ oors.

1. Remove the castors from the bucket of the dehumidiﬁ er.

2. Position the dehumidiﬁ er on its side.

3. Locate the arrow on the bottom of the dehumidiﬁ er and insert the castor

according to the arrow direction.

4. Slide the castor in as far as it will go. The castor will snap into place.

5. Repeat steps 1 to 4 for the other 3 castors.

When you push the button to change operation modes, the unit will make a beeping sound to indicate that it is

changing modes.

1. Continue Button: Press to activate the continuous dehumidifying operation.

2. Filter Button: This product has a check ﬁ lter feature that is a reminder to clean the air ﬁ lter for more efﬁ cient oper-

ation. The check ﬁ lter light will illuminate after 250 hours of operation. To reset this function after cleaning the ﬁ lter,

press the reset ﬁ lter button and the light will go off.

3. Fan button: Controls the fan speed. Press to select either high (turbo) or normal fan speed. Set the fan control to

high for maximum moisture removal. When the humidity has been reduced and quiet operation is perferred, set the

fan control back to normal.

4. Power Button: Press to turn the dehumidiﬁ er on or off.

5. (

/ ) Buttons: The humidity level can be set within a range of 35% RH (Relative Humidity) to 85% RH in 5%

increments using these buttons. For drier air, press the (

) button and set to a lower percentage value (%). For more

damp air, press the (

) button and set a higher percentage value (%).

6. Timer Button: Press to initiate the auto-start and auto-stop feature. Set a start or stop time from 0.0 to 24 hours using

the (

) and ( ) keys.

7. Display: Shows the actual (± 5% accuracy) room humidity level in a range of 30% RH to 90% RH. Otherwise, dis-

plays selection when programming humidity or timer.

8. Comfort: This function allows you to be comfortable by automatically adjusting the humidity level with the ﬂ uctuating

room temperatures. The humidity level cannot be adjusted in this setting.

Note: The fan does not shut off the moment you remove the bucket, the fan will shut off after 2-3 minutes.

Operating Instructions

TIMER FUNCTIONS

Follow these steps to program the Auto-on or Auto-off feature using the control panel:

Auto-off:

1. When the unit is on, and the TIMER button is pressed, the timer off indicator light illuminates to indicate that the auto-

off program is initiated.

2. Press or hold the UP or DOWN button to change the ‘Auto’ time by 0.5 hour increments, up to 10 hours (then at 1 hour

increments up to 24 hours). The unit control will count down the time remaining until start.

3. Within 5 seconds of setting auto-off time, press the TIMER button again to complete the auto-off program.

Auto-on:

4. When the unit is off, and the TIMER button is pressed, the auto-on program is initiated. Set the auto-on time as in step

2 above. Within 5 seconds of setting auto-on time, press the TIMER button again to complete the auto-on program.

NOTE: When the auto-on and auto-off times are set, within the same program sequence, TIMER ON OFF indicator lights

illuminate indicating that both ON and OFF times are now programmed.

NOTE: Turning the unit ON or OFF at any time, changing the on/off timer setting to 0.0, and a P2 error code will cancel the

Auto-on/off functions.

INDICATOR LIGHT FUNCTIONS

AS - Humidity sensor error -- Unplug the unit and plug it back in. If error repeats, call for service.

ES - Temperature sensor error -- Unplug the unit and plug it back in. If error repeats, call for service.

P2 (or Eb) - Bucket is full or the bucket is not in correct position -- Empty the bucket and/or adjust it to the proper position.

EC - Please ensure that the room ambient temperature matches the recommended operating temperature for the unit,

5°C (41°F) - 35°C (95°F). If the temperature is within this range, call for service.

E3 - Unit Malfunction, unplug the unit and plug it back in. If error repeats, call for service.

ERROR CODES

Note: Depending on the humidity conditions of the surrounding environment, the dehumidiﬁ er may not start automatically

when the “on/off” button is pressed (see dehumidifying mode instructions for details).

9. Bucket Full Indicator Light: When the bucket is full and/or incorrectly positioned inside the cabinet, the bucket full

light will turn on and remain on until the bucket is emptied and/or correctly re-positioned. This condition will result in the

immediate shut down of the dehumidifying system (both compressor and fan motor operation are terminated). This is a

safety feature. When the bucket is emptied and/or correctly re-positioned, the dehumidiﬁ er will resume operation automat-

ically. NOTE: It may take several minutes before operating conditions resume.

10. Auto-defrost: When frost builds on the evaporator coils, the compressor will cycle off and the fan will continue to run

until the frost disappears.

NOTE:

Memory Setting: Each time the unit is disconnected / re-connected and/or in the event of a power failure, the electronic

circuit board automatically defaults to the last program setting that was used. After the unit has stopped, it may take sev-

eral minutes before operating conditions resume.

Auto-restart: If the unit shuts off unexpectedly due to a power outage, it will restart with the previous function settings

automatically when the power resumes.

WATER TANK OPERATION

The water tank holds accumulated condensed water and, by means of a safety switch, controls both the water level and

operation of the dehumidiﬁ cation process.

When the water tank is full and/or accidentally displaced inside the cabinet, the ﬂ oat switch actuator (inside the tank)

breaks contact with the safety switch. This condition results in the immediate shut down of the compressor and fan motor

system, preventing moisture from being condensed.

Note: On some models, the fan will continue to run for approximately 2-3 minutes after the unit has stopped and

the bucket has been removed. As a result, water may drip from the tray onto the base of the unit, and then onto

the ﬂ oor. Please ensure that you protect your wood and carpet from such leakage.

IMPORTANT

Never tamper with or attempt to defeat the water level (safety) ﬂ oat switch system. Proper installation

of the water tank is crucial in maintaining reliable dehumidiﬁ er operation.

Operating Instructions

DEHUMIDIFYING

Dehumidifying is a means of removing moisture from the air. A dehumidiﬁ er will help to protect your home and valued

possessions from damage due to swelling caused by moisture in the air. Essentially a dehumidiﬁ er removes moisture from

air as moist air passes over a dehumidifying (evaporator) coil. Moisture is condensed on the evaporator coil, drained, and

collected inside an internal (removable) water tank located at the front of the unit. The exhausted air being returned into

the room environment is elevated several degrees causing the surrounding air temperature to increase (slightly). This

process also contributes to lowering the relative humidity of the surrounding air.

Note: For optimal performance, ensure that the unit is set at least 10% lower than the relative humidity level. It is normal

for the humidity to vary by 5% above or below the set humidity. It is recommended that in normal conditions, the humidity

be set at 40-45%.

DEHUMIDIFYING MODE INSTRUCTIONS

When the unit is ﬁ rst connected to the electrical outlet, the power light will not light up until the “on/off” button is pressed.

When the “on/off” button is pressed, the power light turns on and the dehumidiﬁ er automatically defaults to:

Display: Current ambient room humidity (RH%)

Humidity Setting: 60% RH

Fan Speed: High.

Note: Depending on humidity conditions of the surrounding environment, the dehumidiﬁ er may not start automatically

under the default setting (this is an indication that the humidity level of the surrounding environment is lower than the

“default” setting of 60% RH). Therefore, it may be necessary to scroll through each of the different dehumidiﬁ er settings

35%-55% until the “humidistat” (sensor) recognizes conditions that will allow the unit to operate.

Dehumidifying Mode Selection:

1. The unit enters dehumidify mode when the ON/OFF button is pressed.

2a. Press the

/ buttons to select a desired RH operating value (35%-85%).

2b. Press the continuous button. When continuous mode is selected, the humidistat (sensor) will be by-passed and the

compressor will operate non-stop regardless of humidity conditions.

Fan Speed Selection:

3. You can choose a fan speed (normal/turbo) using the keypad. The speed you select is identiﬁ ed by the (illuminated)

indicator light located directly above the selection made.

Your dehumidiﬁ er features a removable Air Filter. This ﬁ lter is located at the front of the unit (behind the air intake grill)

directly above the water tank compartment. The air ﬁ lter plays an important role in helping to reduce (minimize) dust/

dirt particles from the surrounding environment. A blocked/clogged air ﬁ lter reduces air intake, impacting negatively on

operating efﬁ ciency. To maintain maximum operating efﬁ ciency, the ﬁ lter must be checked and cleaned regularly (every 2

weeks). More frequent cleaning may be required depending upon indoor air quality.

IMPORTANT: Never operate the unit without the air ﬁ lter in place.

AIR FILTER REMOVAL:

1. Pull ﬁ lter outwards.

2. Clean the ﬁ lter thoroughly using a vacuum cleaner or wash using lukewarm water and mild detergent. Dry thoroughly

before re-installing.

3. To re-install the air ﬁ lter, slide the ﬁ lter back inside the tracks.

AIR FILTER

Operating Instructions

Note: All the pictures in the manual are for explanatory purposes only. The actual shape of the unit you purchased may be

slightly different, but the operation and functions are the same.

There are two ways to remove collected water:

1. Use the bucket

When the unit is off and the bucket is full, the unit will beep 8 times, the

bucket full indicator light will ﬂ ash, and the digital display shows P2.

When the unit is on and the bucket is full, the compressor turns off and

the fan turns off after drying the water off the condenser for 30 seconds.

The unit will then beep 8 times and the bucket full indicator light will

ﬂ ash, and the digital display shows P2.

To empty the full bucket, slowly pull out the bucket. Grip the left and

right handles securely, and carefully pull it straight out so water does

not spill. Do not put the tank on the ﬂ oor because the bottom of the

bucket is uneven. Otherwise the bucket will fall and cause water to spill.

Discard the water and return the bucket to the unit. The bucket must

be placed and properly positioned for the dehumidiﬁ er to operate. The

machine will restart when the bucket is restored in its correct position.

Note: When you remove the bucket, do not touch any parts inside of

the unit. Doing so may damage the product. Be sure to push the bucket

gently all the way into the unit. Banging the bucket against anything or

failing to push it in securely may cause the unit not to operate. When

you remove the bucket, if there is some water inside the unit you must

dry it. The power button ﬂ ashes when the bucket is not properly in

place.

2. Continuous draining:

Water can be automatically emptied into a ﬂ oor drain by attaching the

unit to an ID ≥ 5/16” water hose with a ID:M=1 female threaded end (not

included, a standard garden hose works well). Install the drain hose.

Remove the plastic cover from the back drain outlet of the unit and set it

aside.

Install the female threaded end of the water hose into the adaptor A

(see B4), then lead the water hose to the ﬂ oor drain or a suitable drain-

age facility. Make sure the hose is secure so there are no leaks. Direct

the hose toward the drain, making sure that there are no kinks that will

stop the water from ﬂ owing. Place the end of the hose into the drain and

make sure the end of the hose is level or declining to let the water ﬂ ow

smoothly. Select the desired humidity setting and fan speed on the unit

for continuous draining to start.

Operating Instructions

REMOVING COLLECTED WATER

1. Pull out the bucket a little.

2. Hold both sides of the

bucket with even strength and

pull it out from the unit.

3. Pour the water out.

Remove the plastic

cover by turning it

counter-clockwise.

Drain hose

If the pump hose drops when you

remove the bucket, ensure it is reinstalled properly.

Operating Instructions

CAUTION

1. DO NOT pull on the power cord to avoid breakage, potential danger or

injury.

2. DO NOT use insecticide/ repellents, oil or paint/spray paint around the

machine, these might cause damage to plastic parts or start a ﬁ re.

3. DO NOT place the unit on uneven ground to avoid shaking, noise and

water leakage.

4. Always keep the unit 20 cm or more from the wall to dissipate heat

properly.

5. DO NOT drop anything into the machine.

6. Close all windows to allow for the maximum possible efﬁ ciency for

removing moisture.

7. Keep the machine away from any type of heat source.

8. When moving or putting in storage, do not place the dehumidiﬁ er on its

side or upside down.

Care and Maintenance

IMPORTANT

1. Be sure to unplug the unit before cleaning or servicing.

2. Do not use gasoline, paint thinner or other chemicals to clean the

unit.

3. Do not wash the unit directly under a tap or using a hose. It may

cause electrical damage.

4. If the power cord is damaged, contact the service depot immediately.

CLEANING

1. Clean the grill and case

Use water and a mild detergent. Do not use bleach or abrasives. Do

not splash water directly onto the main unit. Doing so may cause an

electric shock, cause the insulation to deteriorate, or cause the unit

to rust. The air intake and outlet grills become dirty easily, so use a

vacuum attachment or brush to clean.

2. Clean the bucket

Every few weeks, clean the bucket to prevent growth of mold, mil-

dew and bacteria. Partially ﬁ ll the bucket with clean water and add a

small amount of mild detergent. Swish it around in the bucket, empty

and rinse. Note: Do not use a dishwasher to clean the bucket. After

cleaning, the bucket must be placed and properly positioned for the

dehumidiﬁ er to operate.

3. Clean the air ﬁ lter

Remove and clean the ﬁ lter every two weeks based on normal oper-

ating conditions.

Caution: DO NOT operate the dehumidiﬁ er without a ﬁ lter be-

cause dirt and lint will clog it and affect performance.

4. When not using the unit for long periods of time

After turning the unit off, wait one day before emptying the bucket.

Clean the main unit, water bucket and air ﬁ lter. Cover the unit with a

plastic bag. Wrap the cord around the power cord buckle. Store the

unit upright in a dry, well ventilated place.

Power cord buckle

Troubleshooting

Occasionally, a minor problem may arise, and a service call may not be necessary- use this troubleshooting guide for a

possible solution. If the unit continues to operate improperly, call an authorized service depot or Danby’s Toll Free Num-

ber for assistance.

Tel: 1-800-26 - (1-800-263-2629)

PROBLEM POSSIBLE CAUSE SOLUTION

Dehumidiﬁ er

does

not start

• The dehumidiﬁ er is un-

plugged

• The fuse is blown/circuit

breaker is tripped

• Dehumidiﬁ er has reached

its preset level or bucket is

full

• Bucket is not in the proper

position

• Power failure

• Make sure the plug is pushed completely into the outlet

• Check the house fuse/circuit breaker box and replace the

fuse or reset the breaker

• The unit turns off automatically when either condition

occurs. Change to a lower setting or empty the bucket and

replace properly

• The bucket must be in place and securely seated for the

unit to operate.

• There is a protective time delay (up to 3 minutes) to pre-

vent tripping of the compressor overload. For this reason,

the unit may not start normally for 3 minutes after it is

turned back on.

Dehumidiﬁ er does

not dry the air as it

should

• Did not allow enough time

to remove the moisture

• Airﬂ ow is restricted

• Dirty ﬁ lter

• The humidity control may

not be set low enough

• Doors and windows may

not be closed tightly

• Clothes dryer may be blow-

ing moisture-laden air into

the room

• Room temperature is too

low

• When ﬁ rst installed, allow at least 24 hours to maintain the

desired dryness

• Make sure there are no curtains, blinds or furniture block-

ing the front or back of the dehumidiﬁ er. See the “Location”

section.

• See the “Air ﬁ lter” section

• For drier air, press the

button and set to a lower per-

cent value (%)

• Check that all doors, windows and other openings are

securely closed

• Install the dehumidiﬁ er away from the dryer. The dryer

should be vented to the outside.

• Moisture removal is best at higher room temperatures.

Lower room temperatures will reduce the moisture removal

rate. Modes are designed to be operated at temperatures

above 5°C (41°F)

Dehumidiﬁ er runs

too much

• Area to be dehumidiﬁ ed is

too large

• Doors and windows are

open

• The capacity of your dehumidiﬁ er may not be adequate

• Close all doors and windows

Frost appears on

the coils

• Unit has been recently

turned on, or room tempera-

ture is below 5°C (41°F)

• This is normal. Frost will usually disappear within 60 min-

utes. See the “Defrost” section

Controls cannot be

set

• The compressor will turn

off and the fan will auto-

matically continue to run for

approx. 3 minutes at a ﬁ xed

setting

• This is normal. Wait approximately 3 minutes and set the

fan as desired.

Fan noise • Air is moving through the

dehumidiﬁ er

• This is normal

Water on ﬂ oor • Hose connection may be

loose

• Bucket used to collect wa-

ter, but the hose is attached

• Check the hose connection. See “Continuous Drain” sec-

tion

• Disconnect the hose if using the bucket to collect water,

see “Continuous Drain” section.

LIMITED IN-HOME APPLIANCE WARRANTY

This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used under the normal operating

conditions intended by the manufacturer.

This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby Products Inc. (U.S.A.) (hereafter

“Danby”) or by an authorized distributor of Danby, and is non-transferable.

TERMS OF WARRANTY

Plastic parts, are warranted for thirty (30) days only from purchase date, with no extensions provided.

First Year

During the rst twelve (12) months, any functional parts of this product found to be defective, will be repaired or replaced, at warrantor’s

option, at no charge to the ORIGINAL purchaser.

To obtain

Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an Authorized Service Depot. Any app liance

Service

requiring service outside the limited boundaries of “In Home Service” , it will be the consumer’s responsibility to transport the appliance (at

their own expense) to the original retailer (point of purchase) or a service depot for repair. See “Boundaries of In Home Serv ice” below.

Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby service depot, where service

must be performed by a qualied service technician.

If service is performed on the units by anyone other than an authorized service depot, or the unit is used for commercial appli cation, all

obligations of Danby under this warranty shall be void.

Boundaries of

If the appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest service center your unit must be

In Home Service

delivered to the nearest authorized Danby Service Depot, as service must only be performed by a technician qualied and certif ied for

warranty service by Danby. Transportation charges to and from the service location are not protected by this warranty and are t he

responsibility of the purchaser.

Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other c ontents of this appliance, whether due

to any defect of the appliance, or its use, whether proper or improper.

EXCLUSIONS

Save as herein provided, Danby, there are no other warranties, conditions, representations or guarantees, express or implied, m ade or intended by Danby or its

authorized distributors and all other warranties, conditions, representations or guarantees, including any warranties, conditio ns, representations or guarantees

under any Sale of Goods Act or like legislation or statue is hereby expressly excluded. Save as herein provided, Danby shall no t be responsible for any damages

to persons or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction o f the unit and by the purchase of

the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or propert y caused by the unit.

GENERAL PROVISIONS

No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:

1) Power failure.

2) Damage in transit or when moving the appliance.

3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.

4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating con ditions

(extremely high or low room temperature).

5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).

6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, oods etc.

7) Service calls resulting in customer education.

8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for out door application).

Proof of purchase date will be required for warranty claims; so, please retain bills of sale. In the event warranty service is required, present this document to our

AUTHORIZED SERVICE DEPOT.

Danby Products Limited

PO Box 1778, Guelph, Ontario, Canada N1H 6Z9

Telephone: (519) 837-0920 FAX: (519) 837-0449

Danby Products Inc.

PO Box 669, Findlay, Ohio, U.S.A. 45840

Telephone: (419) 425-8627 FAX: (419) 425-8629

04/09

1-800-263-2629

Warranty Service

In-home

If the appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest

service center your unit must be delivered to the nearest authorized Danby Service Depot, as service

must only be performed by a technician qualified and certified for warranty service by Danby. Transpor-

tation charges to and from the service location are not protected by this warranty and are the responsi-

bility of the purchaser.

During the first twenty four (24) months, any functional parts of this product found to be defective, will be

repaired or replaced, at warrantor’s option, at no charge to the ORIGINAL purchaser.

Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an Authorized

Service Depot. Any appliance requiring service outside the limited boundaries of “In Home Service” ,it

will be the consumer’s responsibility to transport the appliance (at their own expense) to the original

retailer (point of purchase) or a service depot for repair. See “Boundaries of In Home Service” below.

Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby

service depot, where service must be performed by a qualified service technician. If service is performed

on the units by anyone other than an authorized service depot, or the unit is used for commercial

application, all obligations of Danby under this warranty shall be void.

First 24 months

To obtain

service

Boundaries of

in-home service

LIMITED CARRY-IN APPLIANCE WARRANTY

This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is

used under the normal operating conditions intended by the manufacturer.

This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or

Danby Products Inc. (U.S.A.) (hereafter “Danby”) or by an authorized distributor of Danby, and is non-transferable.

TERMS OF WARRANTY

Plastic parts, are warranted for thirty (30) days only from purchase date, with no extensions provided.

Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other

contents of this appliance, whether due to any defect of the appliance, or its use, whether proper or improper.

EXCLUSIONS

Save as herein provided, by Danby, there are no other warranties, conditions, representations or guarantees, express or

implied, made or intended by Danby or its authorized distributors and all other warranties, conditions, representations or

guarantees, including any warranties, conditions, representations or guarantees under any Sale of Goods Act or like legislation

or statute is hereby expressly excluded. Save as herein provided, Danby shall not be responsible for any damages to persons

or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction of the unit

and by the purchase of the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for

damages to persons or property caused by the unit.

GENERAL PROVISIONS

No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:

1) Power failure.

2) Damage in transit or when moving the appliance.

3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.

4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating

conditions (extremely high or low room temperature).

5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).

6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, floods etc.

7) Service calls resulting in customer education.

8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for

outdoor application). Proof of purchase date will be required for warranty claims; so, please retain bills of sale. In the event

warranty service is required, present this document to our AUTHORIZED SERVICE DEPOT.

Warranty Service

Carry-In

Danby Products Limited

PO Box 1778, Guelph, Ontario, Canada N1H 6Z9

Telephone: (519) 837-0920 FAX: (519) 837-0449

Danby Products Inc.

PO Box 669, Findlay, Ohio, U.S.A. 45840

Telephone: (419) 425-8627 FAX: (419) 425-8629

1-800-263-2629

07/14

Merci d’avoir choisi Danby

Nous savons que vous êtes excité. Nous sommes aussi! Cependant, le plus que vous vous familiarisez avec votre

nouvel appareil, le mieux va être votre expérience. Nous suggérons donc de lire ces instructions avant connecter votre

nouvel appareil. Ce manuel contient des informations opérationnel important qui vous aidera à faire un usage pleine de les

caractéristiques techniques disponibles dans votre appareil Danby. Le manuel contient également des informations conçu

pour améliorer la fiabilité et la sécurité de votre appareil ainsi que des conseils pour le maintien, pour vous assurez des annees

de bonheur.

Se il vous plaît visitez www.danby.com pour accéder les outils libre-service, FAQ et plus encore. Si jamais vous avez besoin

d'aide supplémentaire, s’il vous plaît appelez 1-800-26-Danby (1-800-263-2629). S’il vous plaît ayez votre facture d’achat, le

numéro de modèle, et le numéro de série près durant l'appel.

Remarque : Ces renseignements seront nécessaires si votre appareil a besoin d’entretien ou pour les demandes de

renseignements généraux. Pour bénéficier d’une opération de maintenance ou de dépannage, le reçu

original sera exigé.

Numéro de modèle :

Numéro de serie :

Date d’achat :

BESOIN D’ASSISTANCE ?

Veuillez trouver quelques conseils avant de faire appel à nos services, cela

nous aidera à mieux vous servir :

Lisez ce guide :

Il comprend des instructions pour l’utilisation et l’entretien adapté de votre

appareil.

Si votre nouvel appareil est endommagé :

Contactez immédiatement le revendeur (ou le fabricant).

Gagnez du temps et de l’argent :

Avant de faire appel à nos services, consultez à nouveau la section

« Dépannage ». Cette section vous aidera à résoudre des problèmes courants.

Si une réparation est nécessaire, ne vous inquiétez pas, la solution est au

bout du fil.

Tel: 1-800-26-

(1-800-263-2629)

Consignes de sécurité importantes

LISEZ TOUTE L’INFORMATION DE SÉCURITÉ AVANT UTILISATION

REMARQUE

Les consignes d'AVERTISSEMENT publiées dans ce manuel ne sont pas supposées couvrir toutes les conditions et situ-

ations éventuelles qui peuvent se produire. La ou les personnes qui installent, entretiennent ou utilisent l’appareil doivent

faire preuve de précaution et de prudence. Si vous n’installez pas, n’entretenez pas ou n’utilisez pas l’appareil conformé-

ment aux instructions du fabricant, il peut se produire des situations présentant des risques de blessures corporelles, de

dommages à l’unité ou autres dommages matériels. Communiquez avec votre concessionnaire, votre représentant ou le

fabricant en cas de problèmes ou de conditions que vous ne comprenez pas bien. Pour parler au service à la clientèle

de Danby, composez le (1-800-263-2629).

Aﬁ n de réduire le risque d'incendie, de choc électrique ou de blessures, tout le câblage et toute la mise à la masse

doivent se conformer à la dernière édition des codes d'électricité locaux et nationaux.

• Il incombe au client de faire vériﬁ er le câblage et les fusibles par un électricien qualiﬁ é pour s'assurer que l'alimentation

électrique disponible est appropriée.

• Cet appareil est conçu pour fonctionner avec un circuit bien mis à la masse, à branchement séparé, polarisé, à trois ﬁ ls

de 120 volts et 60 hertz (courant alternatif). Ce circuit doit être protégé par un fusible de 15 ampères, un fusible équivalent

ou un coupe-circuit. La ﬁ che à trois broches mise à la masse sur le cordon d'alimentation doit être branchée directement

dans la prise susmentionnée de puissance nominale 110/120 V (c.a.).

• Ne branchez pas le déshumidiﬁ cateur à une prise femelle multiple qui sera également utilisée pour d'autres appareils

électriques.

POUR VOTRE SÉCURITÉ : Aﬁ n de réduire le risque d'incendie ou d'explosion, n'entreposez pas ou n'utilisez pas

d'essence ou d'autres vapeurs ou de liquides inﬂ ammables à proximité de cet appareil.

ALIMENTATION

ÉLECTRIQUE

Le mauvais branchement d'un conducteur mis à la masse d'équipement peut résulter dans un risque de choc électrique.

Vériﬁ ez avec un électricien ou un technicien qualiﬁ é si vous n'êtes pas certain que les prises de vos appareils sont bien

mises à la masse.

Cet appareil doit être mis à la masse. En cas de mauvais fonctionnement ou de panne, la mise à la masse réduira le

risque de choc électrique en offrant un circuit avec le moins de résistance au courant électrique. Cet appareil est équipé

d'un cordon électrique avec un conducteur et une ﬁ che à trois broches mis à la masse. La ﬁ che doit être branchée dans

une prise bien installée et mise à la masse conformément aux codes et ordonnances locaux.

• Ne modiﬁ ez pas la ﬁ che livrée avec cet appareil. Si elle ne s'adapte pas à la prise, faites installer une prise adéquate par

un technicien qualiﬁ é.

• Si l'alimentation électrique de votre maison ne satisfait pas aux spéciﬁ cations susmentionnées ou si vous n'êtes

pas certain que votre maison a une mise à la terre efﬁ cace, demandez à un technicien qualiﬁ é ou à une compagnie

d'électricité de le vériﬁ er et de rectiﬁ er tous les problèmes.

GARDEZ CES INSTRUCTIONS

MISE À LA TERRE

CONSIGNES

Consignes de sécurité importantes

LISEZ TOUTE L’INFORMATION DE SÉCURITÉ AVANT UTILISATION

MESURES DE SÉCURITÉ

Lors de l’utilisation de ce déshumidiﬁ cateur, suivez toujours les mesures de sécurité de base, y compris les suivantes :

• N’utilisez cet appareil qu’aux ﬁ ns pour lesquelles il est conçu, tel que décrit dans ce guide d’utilisation.

• Ne pas retirer le morceau de styromousse dans le récipient, puisque celui-ci agit comme indicateur du niveau d’eau.

• Ce déshumidiﬁ cateur doit être installé et mis à la terre correctement, tel que décrit dans ce guide, avant d’être utilisé.

• Ne faites jamais fonctionner ce déshumidiﬁ cateur à un endroit où de l’eau stagnante est susceptible de s’accumuler.

Dans une telle situation, pour votre sécurité, débranchez l’alimentation avant de marcher dans l’eau.

• Ne débranchez jamais votre déshumidiﬁ cateur en tirant sur le cordon d’alimentation. Tenez toujours la ﬁ che fermement

et tirez bien droit pour la retirer de la prise.

• Remplacez immédiatement tous les cordons d’alimentation efﬁ lochés ou qui présentent d’autres dommages. Un

cordon d’alimentation endommagé doit être remplacé par un nouveau cordon obtenu auprès du fabricant; il ne doit

pas être réparé. N’utilisez pas un cordon qui présente des ﬁ ssures ou des dommages causés par l’abrasion, soit sur le

cordon lui-même, soit à l’extrémité de la ﬁ che ou du raccord.

• Si la prise ne correspond pas à la ﬁ che, la prise doit être changée par un électricien qualiﬁ é.

• Éteignez le déshumidiﬁ cateur et débranchez-le avant de le nettoyer.

• Pour votre sécurité, n’entreposez et n’utilisez pas de matières combustibles, d’essence ou d’autres liquides ou vapeurs

inﬂ ammables à proximité de cet appareil ou de tout autre appareil.

• Tous les déshumidiﬁ cateurs contiennent des ﬂ uides frigorigènes qui, en vertu des lois fédérales, doivent être enlevés

avant que le produit soit mis au rebut. Si vous vous débarrassez d’un produit contenant des ﬂ uides frigorigènes,

demandez conseil à l’entreprise qui s’occupe de la mise au rebut pour connaître la marche à suivre. Vériﬁ ez le respect

des réglementations locales concernant la mise au rebut approuvée et sécurisée de cet appareil.

• N’utilisez pas cet appareil à l’extérieur.

• Le déshumidiﬁ cateur est uniquement conçu pour des utilisations résidentielles à l’intérieur. Ce déshumidiﬁ cateur ne doit

pas servir à des utilisations commerciales ou industrielles.

GARDEZ CES INSTRUCTIONS

La page charge ...

Danby DDR50B3WP Mode d'emploi

Marque: Danby

Modèle: DDR50B3WP

Catégorie: Déshumidificateurs

Taper: Mode d'emploi

Ce manuel convient également à

DDR45B3WP

Télécharger le PDF

rapport

dans d''autres langues

English: Danby DDR50B3WP User guide
español: Danby DDR50B3WP Guía del usuario

Danby DDR50B3WP Mode d'emploi

Ce manuel convient également à

Danby DDR50B3WP Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents