Hitachi Cordless Drill DH 24DV Manuel utilisateur

CONTENTS

English

Page

IMPORTANT SAFETY INFORMATION ................. 3

MEANINGS OF SIGNAL WORDS......................... 3

SAFETY ...................................................................... 4

GENERAL SAFETY RULES – FOR ALL

BATTERY OPERATED TOOLS ....................... 4

SPECIFIC SAFETY RULES AND SYMBOLS ......... 6

IMPORTANT SAFETY INSTRUCTIONS FOR

USE OF THE CORDLESS ROTARY

HAMMER ........................................................ 8

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CHARGER .............................. 8

IMPORTANT SAFETY INSTRUCTIONS

FOR USE OF THE BATTERY AND

BATTERY CHARGER ...................................... 9

FUNCTIONAL DESCRIPTION .................................. 11

MODEL ................................................................. 11

TABLE DES MATIERES

ÍNDICE

Página

NOMENCLATURA ............................................... 65

ESPECIFICACIONES ............................................ 66

MONTAJE Y OPERACIÓN ....................................... 67

APLICACIONES ................................................... 67

MÉTODO DE EXTRACCIÓN E INSTALACIÓN

DE LA BATERÍA ............................................ 67

MÉTODO DE CARGA .......................................... 67

ANTES DE LA UTILIZACIÓN .............................. 70

ANTES DE LA OPERACIÓN ................................ 70

COMO SE USA .................................................... 72

MANTENIMIENTO E INSPECCIÓN ........................ 76

ACCESORIOS ........................................................... 78

ACCESORIOS ESTÁNDAR .................................. 78

ACCESORIOS OPCIONALES .............................. 79

LISTA DE PIEZAS .................................................... 84

Page

NAME OF PARTS ................................................ 11

SPECIFICATIONS ................................................ 13

ASSEMBLY AND OPERATION ............................... 14

APPLICATIONS.................................................... 14

REMOVAL AND INSTALLATION METHOD

OF BATTERY .................................................... 14

CHARGING METHOD.......................................... 14

BEFORE USE ....................................................... 17

PRIOR TO OPERATION ....................................... 17

HOW TO USE ...................................................... 19

MAINTENANCE AND INSPECTION ....................... 23

ACCESSORIES ......................................................... 25

STANDARD ACCESSORIES ............................... 25

OPTIONAL ACCESSORIES ................................. 25

PARTS LIST .............................................................. 84

Page

INFORMATIONS IMPORTANTES DE SÉCURITÉ

......... 30

SIGNIFICATION DES MOTS D’AVERTISSEMEN

T .... 30

SECURITE ................................................................ 31

REGLES GENERALE DE SECURITE – POUR TOUS

LES OUTILS FONCTIONNANT SUR BATTERIE ...

31

REGLES DE SECURITE SPECIFIQUES ET SYMBOLES .........

33

CONSIGNES DE SÉCURITÉ IMPORTANTES

POUR L'UTILISATION DU MARTEAU

PERFORATEUR À BATTERIE ...................... 35

CONSIGNES DE SÉCURITÉ IMPORTANTES

POUR LE CHARGEUR DE BATTERIE .......... 35

CONSIGNES DE SÉCURITÉ IMPORTANTES POUR L’UTILISATION

DE LA BATTERIE ET DU CHARGEUR DE BATTERIE ...

36

DESCRIPTION FONCTIONNELLE ........................... 38

MODELE ............................................................... 38

Page

NOM DES PARTIES ............................................. 38

SPECIFICATIONS ................................................ 40

ASSEMBLAGE ET FONCTIONNEMENT ..........................

41

UTILISATIONS ..................................................... 41

MÉTHODE DE RETRAIT ET D’INSTALLATION

DE LA BATTERIE .......................................... 41

MÉTHODE DE RECHARGE ................................. 41

AVANT L’UTILISATION ...................................... 44

AVANT LA MISE EN MARCHE ........................... 44

UTILISATION ....................................................... 47

ENTRETIEN ET INSPECTION .................................. 50

ACCESSOIRES ......................................................... 52

ACCESSOIRES STANDARD ............................... 52

ACCESSOIRES EN OPTION ................................ 52

LISTE DES PIECES ................................................... 84

Français

Español

Página

INFORMACIÓN IMPORTANTE SOBRE SEGURIDAD......

57

SIGNIFICADO DE LAS PALABRAS DE SEÑALIZACIÓN

..... 57

SEGURIDAD ............................................................. 58

NORMAS GENERALES DE SEGURIDAD – PARA TODAS

LAS HERRAMIENTAS ALIMENTADAS CON BATERÍA

... 58

NORMAS Y SÍMBOLOS ESPECÍFICOS DE SEGURIDAD

.... 60

INSTRUCCIONES IMPORTANTES PARA

LA UTILIZACIÓN DEL TALADRO DE

PERCUSIÓN SIN CABLE .............................. 62

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

PARA EL CARGADOR DE BATERÍAS

................. 62

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

PARA LA BATERÍA Y EL CARGADOR DE BATERÍAS

... 64

DESCRIPCIÓN FUNCIONAL .................................... 65

MODELO .............................................................. 65

01e_dh24dv_e(1-14).p65 4/16/04, 0:52 PM2

English

3

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in

the Instruction Manual before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the

failure to observe basic safety rules or precautions. An accident can often be avoided by

recognizing a potentially hazardous situation before it occurs, and by observing appropriate

safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual

and in the sections which contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by

WARNINGS on the power tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been specifically recommended by

HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in

death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in

minor or moderate injury, or may cause machine damage.

NOTE emphasizes essential information.

01e_dh24dv_e.p65 4/13/04, 11:29 PM3

English

4

SAFETY

GENERAL SAFETY RULES – FOR ALL BATTERY OPERATED TOOLS

WARNING: Read and understand all instructions.

Failure to follow all instructions listed below, may result in electric shock,

fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

1. Work Area

(1) Keep your work area clean and well lit. Cluttered benches and dark areas invite

accidents.

(2) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power tools create sparks which may ignite the

dust of fumes.

(3) Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

2. Electrical Safety

(1) A battery operated tool with integral batteries or a separate battery pack must be

recharged only with the specified charger for the battery.

A charger that may be suitable for one type of battery may create a risk of fire when

used with another battery.

(2) Use battery operated tool only with specifically designed battery pack.

Use of any other batteries may create a risk of fire.

3. Personal Safety

(1) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use tool while tired or under the influence of drugs, alcohol, or

medication. A moment of inattention while operating power tools may result in

serious personal injury.

(2) Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep

your hair, clothing and gloves away from moving parts. Loose clothes, jewelry, or

long hair can be caught in moving parts.

(3) Avoid accidental starting. Be sure switch is off position before inserting battery.

Carrying tools with your finger on the switch or inserting the battery pack into a

tool with the switch on invites accidents.

(4) Remove adjusting keys or wrenches before turning the tool on. A wrench or a key

that is left attached to a rotating part of the tool may result in personal injury.

(5) Do not overreach. Keep proper footing and balance at all times. Proper footing and

balance enable better control of the tool in unexpected situations.

(6) Use safety equipment. Always wear eye protection. Dust mask, non-skid safety

shoes, hard hat, or hearing protection must be used for appropriate conditions.

01e_dh24dv_e.p65 4/13/04, 11:29 PM4

English

5

4. Tool Use and Care

(1) Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead

to loss of control.

(2) Do not force tool. Use the correct tool for your application. The correct tool will do

the job better and safer at the rate for which it is designed.

(3) Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled

with the switch is dangerous and must be repaired.

(4) Disconnect battery pack from tool or place the switch in the locked or off position

before making any adjustments, changing accessories, or storing the tools. Such

preventive safety measures reduce the risk of starting the tool accidentally.

(5) Store idle tools out of reach of children and other untrained persons. Tools are

dangerous in the hands of untrained users.

(6) When battery pack is not in use, keep it away from other metal objects like: paper

clips, coins, keys, nails, screws, or other small metal objects that can make a

connection from one terminal to another.

Shorting the battery terminals together may cause sparks, burns, or a fire.

(7) Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained

tools, with sharp cutting edges are less likely to bind and are easier to control.

(8) Check for misalignment or binding of moving parts, breakage of parts, and any

other condition that may affect the tools operation. If damaged, have the tool

serviced before using. Many accidents are caused by poorly maintained tools.

(9) Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool, may become hazardous when used

on another tool.

5. Service

(1) Tool service must be performed only by qualified repair personnel. Service or

maintenance performed by unqualified personnel could result in a risk of injury.

(2) When servicing a tool, use only identical replacement parts. Follow instructions in

the Maintenance section of this manual. Use of unauthorized parts or failure to

follow Maintenance Instruction may create a risk of electric shock or injury.

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other construction

activities contains chemicals known to the State of California to cause cancer, birth

defects or other reproductive harm. Some examples of these chemicals are:

● Lead from lead-based paints,

● Crystalline silica from bricks and cement and other masonry products, and

● Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of

work. To reduce your exposure to these chemicals: work in a well ventilated area, and

work with approved safety equipment, such as those dust masks that are specially

designed to filter out microscopic particles.

01e_dh24dv_e.p65 4/13/04, 11:29 PM5

English

6

SPECIFIC SAFETY RULES AND SYMBOLS

1. Hold tools by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring. Contact with a “live” wire will make exposed

metal parts of the tool “live” and shock the operator.

2. ALWAYS wear ear plugs when using the tool for extended periods.

Prolonged exposure to high intensity noise can cause hearing loss.

3. Never touch moving parts.

Never place your hands, fingers or other body parts near the tool’s moving parts.

4. Never operate without all guards in place.

Never operate this tool without all guards or safety features in place and in proper

working order. If maintenance or servicing requires the removal of a guard or safety

feature, be sure to replace the guard or safety feature before resuming operation of the

tool.

5. Use right tool.

Don’t force small tool or attachment to do the job of a heavy-duty tool.

Don’t use tool for purpose not intended —for example— don’t use circular saw for

cutting tree limbs or logs.

6. Never use a power tool for applications other than those specified.

Never use a power tool for applications other than those specified in the Instruction

Manual.

7. Handle tool correctly.

Operate the tool according to the instructions provided herein. Do not drop or throw

the tool. Never allow the tool to be operated by children, individuals unfamiliar with its

operation or unauthorized personnel.

8. Definitions for symbols used on this tool

V ............... volts

.............. direct current

n

o

.............. no load speed

---/min ...... revolutions or reciprocation per minute

9. Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted. Check their condition periodically.

10. Do not use power tools if the plastic housing or handle is cracked.

Cracks in the tool’s housing or handle can lead to electric shock. Such tools should not

be used until repaired.

11. Blades and accessories must be securely mounted to the tool.

Prevent potential injuries to youself or others. Blades, cutting implements and

accessories which have been mounted to the tool should be secure and tight.

01e_dh24dv_e.p65 4/13/04, 11:29 PM6

English

7

12. Never use a tool which is defective or operating abnormally.

If the tool appears to be operating unusually, making strange noises, or otherwise

appears defective, stop using it immediately and arrange for repairs by a Hitachi

authorized service center.

13. Carefully handle power tools.

Should a power tool be dropped or struck against hard materials inadvertently, it may

be deformed, cracked, or damaged.

14. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner, benzine, carbon tetrachloride, and alcohol may

damage and crack plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly dampened with soapy water and dry

thoroughly.

15. Keep motor air vent clean.

The tool’s motor air vent must be kept clean so that air can freely flow at all times.

Check for dust build-up frequently.

16. ALWAYS wear eye protection that meets the requirement of the latest revision of ANSI

Standard Z87.1.

01e_dh24dv_e.p65 4/13/04, 11:29 PM7

English

8

IMPORTANT SAFETY INSTRUCTIONS FOR USE OF THE

CORDLESS ROTARY HAMMER

WARNING: Death or serious bodily injury could result from improper or unsafe use

of the cordless rotary hammer. To avoid these risks, follow these basic

safety instructions:

1. NEVER touch the tool bit with bare hands after operation.

2. NEVER wear gloves made of stuff liable to roll up such as cotton, wool cloth or string,

etc.

3. ALWAYS attach the side handle and securely grip the Cordless Rotary Hammer.

4. ALWAYS be careful with buried object such as an underground, wiring.

Touching these active wiring or electric cable with this tool, you may receive an electric

shock.

Comfirm if there are any buried object such as electric cable within the wall, floor or

ceiling where you are going to operate here after.

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CHARGER

1. This manual contains important safety and operating instructions for battery charger

Model UC24YFB.

2. Before using battery charger, read all instructions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using battery.

3. To reduce risk of injury, charge HITACHI rechargeable battery type EB2420. Other type

of batteries may burst causing personal injury and damage.

4. Do not expose battery charger to rain or snow.

5. Use of an attachment not recommended or sold by the battery charger manufacturer

may result in a risk of fire, electric shock, or injury to persons.

6. To reduce risk of damage to electric plug and cord, pull by plug when disconnecting

battery charger.

7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise

subjected to damage or stress.

8. An extension cord should not be used unless absolutely necessary. Use of improper

extension cord could result in a risk of fire and electric shock.

If extension cord must be used make sure:

a. That blades of extension cord are the same number, size, and shape as those of

plug on battery charger;

b. That extension cord is properly wired and in good electrical condition; and

c. That wire size is large enough for AC ampere rating of battery charger as specified

in Table 1.

01e_dh24dv_e.p65 4/13/04, 11:29 PM8

English

9

* If the input rating of a battery charger is given in watts rather than in amperes, the

corresponding ampere rating is to be determined by dividing the wattage rating by the

voltage rating-for example:

9. Do not operate battery charger with damaged cord or plug-replace them immediately.

10. Do not operate battery charger if it has received a sharp blow, been dropped, or otherwise

damaged in any way; take it to a qualified serviceman.

11. Do not disassemble battery charger; take it to a qualified serviceman when service or

repair is required. Incorrect reassembly may result in a risk of electric shock or fire.

12. To reduce risk of electric shock, unplug charger from receptacle before attempting any

maintenance or cleaning. Removing the battery will not reduce this risk.

13. This battery charger might be attached to HITACHI battery operated tools as a standard

accessory. In this case, please confirm Instruction Manual of the HITACHI battery

operated tools before using the battery charger.

IMPORTANT SAFETY INSTRUCTIONS FOR USE OF THE

BATTERY AND BATTERY CHARGER

You must charge the battery before you can use the cordless rotary hammer. Before using

the model UC24YFB battery charger, be sure to read all instructions and cautionary

statements on it, the battery and in this manual.

REMEMBER: USE ONLY HITACHI BATTERY TYPE EB2420. OTHER TYPES OF BATTERIES

MAY BURST AND CAUSE INJURY!

Follow these instructions to avoid the risk of injury:

WARNING: Improper use of the battery or battery charger can lead to serious injury.

To avoid these injuries:

1. NEVER disassemble the battery.

2. NEVER incinerate the battery, even if it is damaged or is completely worn out. The

battery can explode in a fire.

Table 1

RECOMMENDED MINIMUM AWG SIZE FOR

EXTENSION CORDS FOR BATTERY CHARGERS

AC Input Rating Amperes* AWG Size of Cord

Equal to or but less Length of Cord, Feet (Meter)

greater than than 25 (7.5) 50 (15) 100 (30) 150 (45)

0 2 18 18 18 16

2 3 18 18 16 14

3 4 18 18 16 14

1250 watts

125 volts

= 10 amperes

01e_dh24dv_e.p65 4/13/04, 11:29 PM9

English

10

3. NEVER short-circuit the battery.

4. NEVER insert any objects into the battery charger’s air vents. Electric shock or

damage to the battery charger may result.

5. NEVER charge outdoors. Keep the battery away from direct sunlight and use only

where there is low humidity and good ventilation.

6. NEVER charge when the temperature is below 32°F (0°C) or above 104°F (40°C).

7. NEVER connect two battery chargers together.

8. NEVER insert foreign objects into the hole for the battery or the battery charger.

9. NEVER use a booster transformer when charging.

10. NEVER use an engine generator or DC power to charge.

11. NEVER store the battery or battery charger in places where the temperature may

reach or exceed 104°F (40°C).

12. ALWAYS operate charger on standard household electrical power (120 volts). Using

the charger on any other voltage may overheat and damage the charger.

13. ALWAYS wait at least 15 minutes between charges to avoid overheating the charger.

14. ALWAYS disconnect the power cord from its receptacle when the charger is not in

use.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS OF THIS TOOL!

01e_dh24dv_e.p65 4/13/04, 11:29 PM10

English

11

FUNCTIONAL DESCRIPTION

NOTE: The information contained in this Instruction Manual is designed to assist you in

the safe operation and maintenance of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have first read

and understood all safety instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that

differ from those on your own power tool.

MODEL

DH24DV (BFK): with charger (UC24YFB) and case

DH24DV (2BFK): with charger (UC24YFB), case and extra battery

NAME OF PARTS

1. Cordless Rotary Hammer (DH24DV)

Grip Change lever

Side handle

Batery

Switch trigger

Shift knob

Push button

Front cap

Depth gauge

01e_dh24dv_e.p65 4/13/04, 11:29 PM11

English

12

䡬 Battery (EB2420)

Fig. 1

Nameplate

Latch

Terminal Hole

2. Battery Charger (UC24YFB)

Pilot Lamp

Guide Rail

Caution Plate

Nameplate

Fig. 2

01e_dh24dv_e.p65 4/13/04, 11:29 PM12

English

13

Input power source Single phase: AC 120 V 60 Hz

Charging time Approx. 50 min. (At a temperature of 68°F (20°C))

Charger

Charging voltage .......................... DC 24 V

Charging current........................... DC 2.5 A

Weight 1.3 lbs. (0.6 kg)

2. Battery Charger (UC24YFB)

* Do not use the “SAVE” mode when boring holes with the wood drill. There is a likelihood

that the motor will burn out.

SPECIFICATIONS

1. Cordless Rotary Hammer (DH24DV)

Motor DC motor

No-load speed SAVE/POWER 0–500/min. / 0–1000/min.

Full-load impact rate SAVE/POWER 0–2200/min. / 0–4500/min.

Concrete 15/16″ (24 mm)

Capacity Drilling Steel 1/2″ (13 mm)

Wood 1–3/16″ (30 mm) *

Battery (EB2420)

Nickel cadmium battery

Voltage ........ DC 24 V

Weight 8.9 lbs. (4.0 kg)

01e_dh24dv_e.p65 4/13/04, 11:29 PM13

English

14

ASSEMBLY AND OPERATION

APPLICATIONS

Rotation and striking function

䡬 Drilling anchor holes

䡬 Drilling holes in concrete

䡬 Drilling holes in tile

Rotation only function

䡬 Drilling in steel or wood

䡬 Tightening machine screws, wood screws

REMOVAL AND INSTALLATION METHOD OF BATTERY

1. Battery removal

Hold the handle tightly and push the battery latches to remove the battery (See Figs. 3

and 4).

2. Battery installation

Insert the battery aligning both guide rail of battery and body. Make sure the battery is

fixed firmly. (See Fig. 4)

CHARGING METHOD

NOTE: Before plugging into the receptacle, make sure the following points.

䡬 The power source voltage is stated on the nameplate.

䡬 The cord is not damaged.

WARNING: Do not charge at voltage higher than indicated on the nameplate.

If charged at voltage higher than indicated on the nameplate, the

charger will burn up.

1. Insert the plug of battery charger into the receptacle.

When the plug of battery charger has been inserted into the receptacle, pilot lamp will

blink in red. (At 1-second intervals)

Fig. 3 Fig. 4

Latch

Guide Rail of Battery

Battery

Guide Rail of Housing

Pull Out

Insert

Housing

01e_dh24dv_e.p65 4/14/04, 5:26 PM14

English

15

WARNING:

Do not use the electrical cord if damaged. Have it repaired immediately.

2. Insert the battery to the battery charger.

Insert the battery into the battery charger as shown in Fig. 5. Make sure the battery is

fully seated in the battery charger.

Before insert After insert

Fig. 5

3. Charging

䡬 When the battery is connected to the battery charger, charging will commence and the

pilot lamp will light in red. (See Table 2)

NOTE: If the pilot lamp flikers in red, pull out the plug from the receptacle and check if

the battery is properly mounted.

䡬 When the battery is fully charged, the pilot lamp will blink in red slowly. (At 1-second

intervals) (See Table 2)

Table 2

Indications of the pilot lamp

Lights for 0.5 seconds. Does not light for

0.5 seconds. (off for 0.5 seconds)

Lights continuously

Lights for 0.5 seconds. Does not light for

0.5 seconds. (off for 0.5 seconds)

Lights for 0.1 seconds. Does not light for

0.1 seconds. (off for 0.1 seconds)

Lights continuously

Before

charging

While

charging

Charging

complete

Charging

impossible

Charging

impossible

Malfunction in the battery or the

charger

The battery temperature is high,

making recharging impossible.

Blinks

(RED)

Lights

(RED)

Blinks

(RED)

Flickers

(RED)

Lights

(GREEN)

01e_dh24dv_e.p65 copy 4/13/04, 11:29 PM15

English

16

䡬 Regarding the temperature of the rechargeable battery

The temperatures for rechargeable batteries are as shown in the table below, and

batteries that have become hot should be cooled for a while before being recharged.

䡬 Regarding recharging time

Table 4 shows the recharging time required according to the type of battery.

Table 4 Recharging time (approx. min.) at 68°F (20°C)

NOTE: The recharging time may vary according to ambient temperature and power

source voltage.

4. Disconnect battery charger from the receptacle.

CAUTION:

Do not pull the plug out of the receptacle by pulling on the cord.

Make sure to grasp the plug when removing from receptacle to avoid damaging cord.

5. Remove the battery from the battery charger.

Supporting the battery charger with hand, pull out the battery from the battery charger.

CAUTION:

● When the battery charger has been continuosly used, the battery charger will heated,

thus constituting the cause of the failures. Once the charging has been completed,

give 15 minutes rest until the next charging.

● If the battery is rechraged when it is warm due to battery use or exposure to sunlight,

the pilot lamp may light in green.

The battery will not be recharged. In such a case, let the battery cool before charging.

Regarding electric discharge in case of new batteries, etc.

As the internal chemical substance of new batteries and batteries that have not been

used for an extended period is not activated, the electric discharge might be low when

using them the first and second time. This is a temporary phenomenon, and normal

time required for recharging will be restored by recharging the batteries 2 – 3 times.

Table 3

Temperatures at which the battery can be recharged

23°F — 140°F

(–5°C — 60°C)

Rechargeable batteries

EB2420

Battery Voltage (V)

Battery capacity (Ah)

2.0 Ah

24 V EB2420 50 min.

01e_dh24dv_e.p65 copy 4/13/04, 11:29 PM16

English

17

How to make the batteries perform longer

(1) Recharge the batteries before they become completely exhausted.

When you feel that the power of the tool becomes weaker, stop using the tool and

recharge its battery. If you continue to use the tool and exhaust the electric current, the

battery may be damaged and its life will become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after use. If such a battery is recharged

immediately after use, its internal chemical substance will deteriorate, and the battery

life will be shortened. Leave the battery and recharge it after it has cooled for a while.

BEFORE USE

Check the work area to make sure that it is clear of debris and clutter.

Clear the area of unnecessary personnel. Ensure that lighting and ventilation is adequate.

PRIOR TO OPERATION

1. Confirming condition of the environment

Confirm that the work site is placed under appropriate conditions conforming to

prescribed precautions.

2. Attaching the side handle (Fig. 6)

(1) Turn the grip of the side handle to loosen it and

push it in until it comes in contact with the housing.

(2) Adjust the side handle to the angle that allows

the easiest use, then turn the side handle’s grip

firmly to lock it place.

3. Mounting the drill bit (Fig. 7)

(1) Clean the shank portion of the drill bit.

(2) Insert the drill bit in a twisting manner into the

tool holder until it latches itself. (Fig. 7)

(3) Check the latching by pulling on the drill bit.

(4) To remove the drill bit, fully pull the grip in the

direction of the arrow and pull out the drill bit.

(Fig. 8)

4. Installation of dust cup or dust collector (B)

(Optional accessories) (Fig. 9, Fig. 10)

When using a rotary hammer for upward drilling

operations attach a dust cup or dust collector (B)

to collect dust or particles for easy operation.

䡬 Installing the dust cup

Use the dust cup by attaching to the drill bit a

shown in Fig. 9.

When using a bit which has big diameter, enlarge

the center hole of the dust cup with this rotary

hammer.

Housing

Fig. 6

Loosen

Side

handle

Part of

SDS-plus

shank

Drill

bit

Grip

Front

cap

Fig. 7

Tighten

01e_dh24dv_e.p65 copy 4/15/04, 4:48 PM17

English

18

䡬 Installing dust collector (B)

When using dust collector (B), insert dust collector

(B) from the tip of the bit by aligning it to the

groove on the grip. (Fig. 10)

CAUTION:

● The dust cup and dust collector (B) are for exclusive

use of concrete drilling work. Do not use them for

wood or metal drilling work.

● Insert dust collector (B) completely into the chuck

part of the main unit.

● When turning the rotary hammer on while dust

collector (B) is detached from a concrete surface,

dust collector (B) will rotate together with the drill

bit. Make sure to turn on the switch after pressing

dust cup on the concrete surface. (When using dust

collector (B) attached to a drill bit that has more

than 7-15/32" (190 mm) of overall length, dust

collector (B) cannot touch the concrete surface and

will rotate. Therefore please use dust collector (B)

by attaching to drill bits which have 6-17/32" (166

mm), 6-19/64" (160 mm) and 4-21/64" (110 mm)

overall length.

● Dump particles after every two or three holes

when drilling.

● Please replace the drill bit after removing dust

collector (B).

5. Selecting the driver bit

Screw heads or bits will be damaged unless a bit appropriate for the screw diameter is

employed to drive in the screws.

6. Confirm the direction of bit rotation (Fig. 11)

The bit rotates clockwise (viewed from the rear side) by pushing the R-side of the

push button. (Fig. 11-a)

The L-side of the push button is pushed to turn the bit counterclockwise. (Fig. 11-b)

The motor does not rotate if the push button is set to the center position. (Fig. 11-c)

Dust collector (B)

Fig. 10

Grip

Part of

SDS-plus

shank

Drill bit

Fig. 9

Dust Cup

Fig. 8

01e_dh24dv_e.p65 copy 4/14/04, 5:50 PM18

English

19

(b) Reverse rotation

(a) Forward rotation

(c) Does not rotate

HOW TO USE

1. Switch operation

䡬 When the switch trigger is depressed, the tool

rotates. When the switch trigger is released, the

tool stops.

䡬 The rotational speed of the rotary hammer can be

controlled by varying the amount that the switch

trigger is pulled. Speed is low when the switch

trigger is pulled slightly and increases as the

switch trigger is pulled more.

䡬 When releasing the switch trigger, the brake will

be applied for immediate stopping.

2. Rotation + Striking

Align the “ ” mark with the “ ” mark by rotating

the change lever to set the “Rotation + Striking”

mode. (Fig. 12)

(1) Mount the drill bit.

(2) Pull the trigger switch after applying the drill bit

tip to the drilling position. (Fig. 13)

(3) Pushing the rotary hammer forcibly is not

necessary at all. Pushing slightly so that drill dust

comes out gradually is just sufficient.

CAUTION:

● When the drill bit touches an iron reinforcing rod,

the bit will stop immediately and the rotary

hammer will react to revolve. Therefore please

grip the side handle and handle tightly as shown

in Fig. 13.

Fig. 11 Diagram seen from the handle side

Push

the

R

side

Push

button

Push

the

L

side

Push

button

Push

button

Center

position

“ ”

mark

“

”

mark

“ ”

mark

Change

lever

Fig. 12

Fig. 13

R

indication

L

indication

01e_dh24dv_e.p65 copy 4/14/04, 7:43 PM19

English

20

3. Rotation only

Align the “ ” mark with the “ ” mark by rotating

the change lever to set the “Rotation only” mode.

(Fig. 12)

To drill a wood or metal material using the

separately sold drill chuck and chuck adaptor,

proceed as follows. Installing drill chuck and chuck

adaptor (Fig. 14):

(1) Attach the drill chuck to the chuck adaptor.

(2) The part of the SDS-plus shank is the same as the

drill bit. Therefore, refer to the item of “Mounting

the drill bit” for attaching it.

CAUTION:

● Application of force more than necessary will not only reducing drilling efficiency at

all, but will deteriorate the tip edge of the drill bit and reduce the service life of the

rotary hammer in addition.

● Drill bit may snap off while withdrawing the rotary hammer from the drilled hole. For

withdrawing, it is important to use a pushing motion.

● Do not attempt to drill anchor holes or holes in concrete with the main unit in the

rotation only mode.

● Do not attempt to use the rotary hammer in the rotation and striking mode with the

drill chuck and chuck adaptor attached. This would seriously shorten the service life of

every components of the machine.

4. When driving machine screws (Fig. 15)

First, insert the bit into the socket in the end of

chuck adaptor (D).

Next, mount chuck adaptor (D) on the main unit

using procedures described in 3 (1), (2), (3), put

the tip of the bit in the slots in the head of the

screw, grasp the main unit and tighten the screw.

CAUTION:

● Exercise care not to excessively prolong driving

time, otherwise, the screws may be damaged by

excessive force.

● Apply the rotary hammer perpendicularly to the

screw head when driving a screw; otherwise, the

screw head or bit will be damaged, or driving force

will not be fully transferred to the screw.

● Do not attempt to use the rotary hammer in the

rotation and striking mode with chuck adaptor

(D) and bit attached.

Part of

SDS-plus

shank

Drill chuck

Front

cap

Grip

Fig. 14

Socket

Chuck

adaptor (D)

Front cap

Grip

Bit

Fig. 15

Chuck adaptor

01e_dh24dv_e.p65 copy 4/15/04, 6:30 PM20

La page charge ...

Hitachi Cordless Drill DH 24DV Manuel utilisateur

Ce manuel convient également à

Hitachi Cordless Drill DH 24DV Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents