Marvel MORF224SS31A Manuel utilisateur

EN Installation, Operation and Maintenance Instructions

FR Instructions d’installation, d’utilisation et d’entretien

ES Instrucciones de instalación, operación y mantenimiento

Outdoor Refrigerator / Freezer

Réfrigérateur / Congélateurs

d'extérieur

Refrigeradores / Congeladors

exterior

2

MO24RF

CONTENTS

Contents: Important Safety Instructions

Safety information ...............................................................2 Warnings and safety instructions appearing in this guide

Unpacking your appliance ..................................................3 are not meant to cover all possible conditions and situa-

Warranty registration ......................................................3 tions that may occur. Common sense, caution, and care

Installing your appliance ......................................................4 must be exercised when installing, maintaining, or

operat-

Cabinet clearances .........................................................4 ing this appliance.

Leveling the appliance ....................................................4

Electrical connection ......................................................5

Recognize Safety Symbols,

Installing the water supply ...................................................6

Optional ice-maker operation ..............................................7

Words, and Labels.

!

CAUTION

!

WARNING

WARNING -

You can be killed or seriously injured

if you do not follow these instructions.

3

Product dimensions ...........................................................8 Death or serious injury could result if...

Starting your appliance ..................................................10

Using your Electronic control ............................................10 Sleep mode

...................................................................10 Turning your appliance "ON" or "OFF" ..........................11 Adjusting

the temperature .............................................11 Temperature mode ........................................................11

Control lock ................................................................12

Temperature sensor error codes ................................12

Alarms

...........................................................................12

Door ajar ..................................................................12

Power failure .............................................................13

Temperature alarm ....................................................13

Vacation mode ..................................................................13

Shelving configurations ....................................................14

Shelf removal ...................................................................15

Care and cleaning .............................................................16

Long term storage/winterization ...................................16

Energy saving tips ............................................................19

Stainless steel maintenance .............................................20

Obtaining service .............................................................20

Troubleshooting

.................................................................21

Troubleshooting ice-maker ..............................................22

Warranty ...........................................................................23

! WARNING

State of California Proposition 65 Warning: This

product contains one or more chemicals known to

the State of California to cause cancer.

CAUTION-Hazards or unsafe practices which could

result in personal injury or property / product damage.

NOTE-Important information to help assure a problem

free installation and operation.

NOTE

4

! WARNING

State of California Proposition 65 Warning: This

product contains one or more chemicals known to

the State of California to cause birth defects or

other reproductive harm..

! WARNING

EXCESSIVE WEIGHT HAZARD

Use two or more people to move product.

Failure to do so can result in personal injury.

Remove Interior Packaging

Your appliance has been packed for shipment with all parts

that could be damaged by movement securely fastened.

Remove internal packing materials and any tape holding

internal components in place. The owners manual is

shipped inside the product in a plastic bag along with the

warranty registration card, and other accessory items.

Important

Keep your carton and packaging until your appliance has

been thoroughly inspected and found to be in good

condition. If there is damage, the packaging will be needed

as proof of damage in transit. Afterwards please dispose of

all items responsibly.

This merchandise was carefully packed and thoroughly

inspected before leaving our plant. Responsibility for its

safe delivery was assumed by the retailer upon acceptance

of the shipment. Claims for loss or damage sustained in

transit must be made to the retailer.

DO NOT RETURN DAMAGED MERCHANDISE TO THE

MANUFACTURER - FILE THE CLAIM WITH THE

RETAILER.

If the appliance was shipped, handled, or stored in other

than an upright position for any period of time, allow the

appliance to sit upright for a period of at least 24 hours

before plugging in. This will assure oil returns to the

compressor. Plugging the appliance in immediately may

cause damage to internal parts.

Warranty Registration

It is important you send in your warranty registration card

immediately after taking delivery of your appliance or you

can register online at www.agamarvel.com.

The following information

will be required when

registering your appliance.

Service Number

Serial Number

Date of Purchase

Dealer’s name and address

The service number and serial number can be found on the

serial plate which is located inside the cabinet on the right

side near the top. (See Figure 1).

UNPACKING YOUR APPLIANCE

Note to Customer

!

WARNING

WARNING -

Dispose of the plastic bags which can

be a suffocation hazard.

NOTE

!

CAUTION

Online registration

available at

www.agamarvel.com

5

Figure 1

! WARNING

WARNING - Help Prevent Tragedies

Child entrapment and suffocation are not problems of

the past. Junked or abandoned refrigerators are still

dangerous - even if they sit out for "just a few hours".

If you are getting rid of your old refrigerator, please

follow the instructions below to help prevent accidents.

Before you throw away your old refrigerator or

freezer:

• Take off the doors or remove the drawers.

• Leave the shelves in place so children may not

easily climb inside.

Select Location

The proper location will ensure peak performance of your

appliance. We recommend a location where the unit will be

out of direct sunlight and away from heat sources. To

ensure your product performs to specifications, the

recommended installation location temperature range is

from 55 to 115°F (13 to 46°C).

Cabinet Clearance

Ventilation is required from the bottom front of the

appliance. Keep this area open and clear of any

obstructions. Adjacent cabinets and counter top can be

installed around the appliance as long as the front grille

remains unobstructed.

Front Grille

Do not obstruct the front grille. The openings within the

front grille allow air to flow through the condenser heat

exchanger. Restrictions to this air flow will result in

increased energy usage and loss of cooling capacity. For

this reason it is important this area not be obstructed and

the grille openings kept clean. AGA MARVEL does not

INSTALLING YOUR APPLIANCE

XXXXXXXXXXXX

!

CAUTION

6

recommend the use of a custom made grille as air flow

may be restricted. (See Figure 2).

Leveling Legs

Adjustable legs at the front and rear corners of the

appliance should be set so the unit is firmly positioned on

the floor and level from side to side and front to back. The

overall height of your Marvel appliance may be adjusted

between the minimum, 33

3

⁄4" (85.7 cm), by turning the

leveling leg in (CW ↷) and the maximum, 34

3

⁄4" (88.3 cm)

by turning the leveling leg out (CCW ↶).

To adjust the leveling legs, place the appliance on a solid

surface and protect the floor beneath the legs to avoid

scratching the floor. With the assistance of another person,

lean the appliance back to access the front leveling legs.

Raise or lower the legs to the required dimension by

turning the legs. Repeat this process for the rear by tilting

the appliance forward using caution. On a level surface

check the appliance for levelness and adjust accordingly.

The front grille screws may be loosened and the grille

adjusted to the desired height. When adjustment is

complete tighten the two front grille screws. (See Figure 5).

INSTALLING YOUR APPLIANCE

! WARNING

Electrical Shock Hazard

Do not remove • Do not use an extension cord with this appliance.

ground prong They can be hazardous and can degrade product

performance.

• This appliance should not, under any circumstances, be installed to an un-grounded

electrical supply.

• Do not remove the grounding prong from the power cord. (See Figure 3).

• Do not use an adapter. (See Figure 4 ).

• Do not splash or spray water from a hose on the

Figure 3

appliance. Doing so may cause an electrical shock,

which may result in severe injury or death.

7

Electrical Connection

A grounded 115 volt, 15 amp dedicated circuit is required.

This product is factory equipped with a power supply cord that has a

three-pronged, grounded plug. It must be

plugged into a mating grounding type receptacle in accor-

Figure 4

dance with the National Electrical Code and applicable lo-

cal codes and

ordinances (see Figure

6). If the circuit does

not have a grounding

type receptacle, it is

the responsibility and

obligation of the

customer to provide the

proper

power

supply.

The

third

ground

prong

should

not,

under any

circumstances, be cut

or removed.

Figure 6

Ground Fault Circuit Interrupters (GFCI) are prone to nuisance

tripping which will cause the appliance to shut down. GFCI’s

are generally not used on circuits with power equipment that

must run unattended for long periods of time, unless required to meet local building codes and ordinances.

INSTALLING THE WATER SUPPLY

MODEL MO24RF WITH OPTIONAL ICE-MAKER KIT

NOTE

8

An optional ice-maker kit (part number S42418151) is

available for model MO24RF which includes all of the

necessary parts for installation. The kit can be obtained from

Marvel customer service by calling 800-223-3900.

Water Supply

Observe and

follow all local

building codes when installing this appliance.

Use

1

⁄4" copper tubing for your water supply which is available

at any local hardware or plumbing supply store. Bend the

1

⁄4"

copper tubing to suit your installation being sure not to kink

the tubing. Purchase enough copper tubing length and coil it

behind the unit to form a "service loop" which will allow the

appliance to be pulled out from the installation for servicing or

cleaning. Connect the copper tubing to the "top side" of a

cold water pipe to prevent the ice-maker from plugging with

sediment.

A shutoff valve is recommended on the water supply line to

ease servicing the appliance. NOTE: A SELF-PIERCING

TYPE VALVE IS NOT RECOMMENDED as they are prone

to clogging with sediment which will create pressure drop

reducing the water supply to the unit.

Connect the copper tubing water supply to the brass union

with a 1/4" compression nut fitting. (See Figure 7).

Water pressure must be at a minimum of 20 psi for proper

operation and a maximum of 120 psi.

Make certain all water connections are watertight after installation. Form the tubing so that it will not

vibrate against the cabinet body or kink when your appliance is set in position.

1

⁄4" copper tubing

• Do not use any thread sealers on these water line fittings.

• Reverse osmosis, softened water, and de-ionized water are not recommended as they will adversely affect the quality

of the ice.

!

CAUTION

NOTE

9

OPTIONAL ICE-MAKER

OPERATION

The water supply to the ice-maker must be turned on prior to

turning the ice-maker on. Failure to do so will cause rapid dry

cycling of the ice-maker mold heater resulting in temperature

control issues in the freezer compartment.

Ice-maker operation

• The unit must be installed level for proper ice-maker

operation.

• The shutoff arm wire must be down in its lowest position for

the ice-maker to operate. (See Figure 8).

• When the freezer section and ice-maker unit has sufficiently

cooled, the ice-maker will harvest ice cubes automatically.

• When the ice bucket is full, the ice-maker will automatically shut off.

• You may manually stop the ice-maker by raising the shut off arm to the locking position at the up most position.

(See Figure 8).

It is recommended the ice-maker is shut off when removing

the bucket, or ice may be dispensed onto the freezer

compartment floor.

If the ice is not used regularly, it will clump together with

time. For best ice results, discard ice in the bin as required

and allow the ice-maker to make a new fresh batch of ice.

Shut-off the ice-maker by raising the shut-off arm before

removing the bucket.

PRODUCT DIMENSIONS

ROUGH-IN OPENING DIMENSIONS

CABINET

DIMENSIONS

MODEL

"A"

"B"

"C"

"D"

"E"

"F"

"G"

"H"

"J"

MO24RFS

24"

(61 cm)

**34" to 35"

(86.4 to 88.9 cm)

*

23

7

⁄8"

(60.7

cm)

33

3

⁄4" to

34

3

⁄4"

(85.7 to

88.3 cm)

23

⁄32"

(60.2

cm)

26

7

⁄32"

(66.6

cm)

46

13

⁄32"

(117.9

cm)

26

1

⁄4"

(66.7

cm)

DOOR STYLE

(S) Solid Door

NOTE

!

CAUTION

Arm down, ice-maker

will operate

Arm up, stops operation

Figure 8

10

opening a hole can be cut through the adjacent cabinet and the power cord routed

through this hole to a power outlet. Another way to increase the available opening

depth is to recess the power outlet into the rear wall to gain

the thickness of the power cord plug. Not all recessed outlet

boxes will work for this application as they are too narrow, but

a recessed outlet box

Figure 10

equivalent to Arlington #DVFR1W is recommended for

this application, (see Figure 10).

PRODUCT DIMENSIONS

PRODUCT DATA

MODEL

ELECTRICAL

REQUIREMENTS #

PRODUCT

WEIGHT

MO24RFS

115V/60Hz/15A

140 lbs

(63.6 kg)

11

* Depth dimension of rough-in opening may vary depending

on each individual installation. To recess entire door "F"

dimension plus 1" (2.5 cm) for thickness of power cord plug.

** Minimum rough-in opening required is to be larger than

the adjusted height of the cabinet.

# A grounded 15 amp dedicated circuit is required. Follow

all local building codes when installing electrical and

appliance.

STARTING YOUR APPLIANCE

Starting your appliance:

Plug the appliance power cord into a 115 volt wall outlet.

Your appliance is shipped from the factory in the "On"

position and will begin start-up of cooling as soon as power

is supplied. If the appliance does not start, confirm that the

Power Failure

ALARM RESET

NOTE

12

wall outlet has power, and that the control is in the "On"

position, (See "Turning your appliance On and Off" below).

The control display is covered with a clear plastic film. This

film may be removed by carefully lifting the film at a corner.

On initial power up, the control display will indicate a

"Power Failure" alarm. This is a normal condition as the

appliance was powered-up at the factory for quality

inspection and then removed from power. A momentary

press of the "On/Off" keypad will reset this alarm

condition. (See Alarms section on page 12).

Temp Temp

Minus On/Off Plus Compartment keypad keypad keypad select

Display Area

Your product has an automatic defrost feature that utilizes

an electric heater element. Periodically during defrost you

may observe the following:

• Water dripping and running sounds as a result of the

frost melt

• Sizzling and popping sounds from water dripping on the

heater element

• A faint reddish glow in the freezer compartment from

the electric heater element

These are all “normal” operating characteristics related to

refrigeration product incorporating automatic defrost. They

do not represent any product fault or safety issue.

Using your electronic control:

Sleep mode:

If no keypads are pressed for 60 seconds, the display will

enter sleep mode to conserve power. The control panel will

go dark with the exception of the system status "OK"

indicator which will remain enabled. Alarm conditions will

wake the display, (see alarms on page 12).

Lock System Status keypad indicators

The sleep mode can be disabled if you prefer to have the

display on continuously. Press and hold the "Lock"

keypad until the display goes past "Loc" and reads "nSL".

To

Figure 12 enable the sleep mode, repeat the instruction, again going

13

past "Loc" until the display reads "SLP".

USING YOUR ELECTRONIC CONTROL

14

Turning your appliance ON and OFF:

If the appliance is "On", (and out of sleep mode) the

temperature will be shown in the display area of the

control. To turn the appliance "Off", press and hold the

"On/Off" keypad for 4-seconds. "OFF" will now be

displayed on the control.

To turn the appliance "On", press and hold the "On/Off"

keypad for 4-seconds.

Adjusting the temperature:

Loading warm contents may trigger a temperature alarm,

see temperature alarm page 13. Depending on the quantity

and/or weight of warm contents, it may take 48 hours for

the compartment temperature to stabilize.

When making temperature set-point changes, it may take

up to 24-hours for the stored contents to stabilize at your

new set-point temperature.

Factors that affect the storage compartment stabilized

temperature:

• Changes to temperature setting.

• Room temperature changes.

• Temperature of stored contents. - Loading warm

contents.

- Cold content load will delay the change to a warmer

set-point temperature.

- Warm content load will delay the change to a colder

set-point temperature.

• Usage, (number and duration of the door openings).

• Installation of the appliance in direct sunlight or next to

a heat source.

FreezerRefrigerator compartmentcompartment

selectedselected

Temperatures can be set for each individual compartment

(refrigerator or freezer / ice-maker). To do so you must first

select the compartment you want to set the temperature

for.

You do so by pressing the refrigerator (REF) or freezer

(FRZ) button on the display. When pressed the LED light

will be illuminated for the respective display.

To change the set temperature for a particular

compartment, with the compartment enabled and out of

sleep mode, press the "-" or "+" keypads. "SET" will be

indicated on the user interface panel and the current set-

point temperature will display and flash. Subsequent

presses of the "-" or "+" keypads will adjust the temperature

colder or warmer respectively. When you have reached

your desired set-point temperature, press the "On/Off"

keypad to accept, or do nothing and the "Set" mode will

time-out in 10-seconds accepting the displayed

temperature as the new set-point.

The available set-point temperature range for your

appliance is -6°F (-21°C) to 6°F (-14°C) for the freezer

compartment (ice-maker) and 34°F (1.2°C) to 42°F (5.7°C)

for the refrigerator compartment. If you attempt to adjust

the temperature outside of these ranges you will receive an

audible notification.

The temperature mode is preset from the factory in

Fahrenheit (°F) but you have the option to change it to

Centigrade (°C). To change the mode, press and hold the

"-" keypad, while pressing the "+" keypad, then release the

"-" keypad. The temperature will now be displayed in

Centigrade (°C). Repeat the procedure to change the

temperature mode back to Fahrenheit (°F).

Control lock:

NOTE

REF

FRZ

REF

FRZ

USING YOUR ELECTRONIC CONTROL

15

The control panel can be locked to avoid unintentional

changes. To lock the control, press and hold the "Lock"

keypad until the display reads "Loc" then immediately

release your finger from the keypad. The lock icon will flash

3-times and then continuously illuminate. When the control

panel is locked, only the Lock keypad, System Status OK

indicator , and the Alarm indicator are active. To un-lock

the control panel, repeat this instruction until the display

reads "nLc" then immediately release your finger from the

keypad.

NOTE

If the control lock is active (illuminated lock icon) the

control will have to be unlocked before using the keypad to

reset an alarm condition. See page 12 (Control Lock) for

instructions for unlocking the control.

Temperature Sensor Error Codes

The temperature sensors are monitored continuously. Any

OPEN or SHORTED circuit condition will initiate an

ERROR CODE as listed below:

Alarms:

The control will alert you to conditions that could adversely

affect the performance of the appliance.

• Door ajar - If the door is open, or not closed

properly, for more than 5-minutes the System Status

OK indicator will turn-off, the "Door Ajar" indicator will

flash, and a tone will sound every 60 seconds.

Additionally, an "ALARM RESET" indicator will be

displayed below the "On/Off" keypad.

The audible alarm can be muted, for each occurrence,

by pressing the lock keypad.

This alarm condition can be reset by closing the door or

momentarily pressing the "On/Off" keypad, (i.e.-if you

are cleaning the storage compartment, etc.). The alarm

will recur in 5-minutes if the alarm condition persists.

Temperature Sensor Error Codes

Sensor

Displayed Code

Error Description

Action to Take

Refrigerator

Temperature

Sensor

Failed temperature sensor in the

refrigerator compartment. Can lead to

unwanted storage temperatures and/or

spoiled perishable goods.

Call service to have the temperature

sensor replaced and

remove all perishable goods from

compartment to prevent spoilage.

Freezer

Temperature

Sensor

Failed temperature sensor in the

freezer compartment. Can lead to

unwanted storage temperatures and/or

spoiled perishable goods.

Call service to have the temperature

sensor replaced and

remove all perishable goods from

compartment to prevent spoilage.

Defrost Sensor

Failed defrost temperature sensor.

Causes unit to not defrost properly and

can create large frost build-up. Can lead

to water damage to the unit and

surrounding floor.

Unplug the power cord immediately

and call service to have the defrost

sensor replaced.

Door Ajar

ALARM RESET

NOTE

USING YOUR ELECTRONIC CONTROL

16

• Power failure - If power to the appliance is

interrupted the System Status indicator will turn-off and

the "Power Failure" indicator will flash. Additionally, an

"ALARM RESET" indicator will be displayed below the

"On/Off" keypad. No audible tone will sound. This

alarm condition can be reset by momentarily pressing

the "On/Off" keypad. If this alarm occurs, it is

recommended that you check the condition of any

perishables, even if the appliance is operating normally

and the temperature has recovered, as prolonged

power outages could result in excessive temperature

excursions which may spoil perishables.

• Temperature alarm - If the storage compartment

temperature deviates excessively from your set-point

temperature for an extended period of time, the

"TEMP" indicator will flash, and an audible tone will

sound every 60 seconds. Additionally, an "ALARM

RESET" indicator will be displayed below the "ON/

OFF" keypad.

After a high temperature alarm condition, check all

perishables to ensure they are safe for consumption.

The temperature alarm may occur as a result of high usage

or introduction of warm contents to the storage

compartment. If the temperature alarm continues to occur,

your unit may require service.

The audible alarm can be muted, for each occurrence,

by pressing the lock keypad.

This alarm condition can be reset by momentarily pressing

the "On/Off" keypad. If this alarm occurs it is recommended

that you check the condition of your stored contents, even

though the appliance is operating normally and the

temperature has recovered, as prolonged temperature

excursions

Multiple alarms are possible, i.e.- "Door Ajar" for a

prolonged period may trigger a "Temp" alarm, in which

case both "Door Ajar" and "Temp" indicators will activate.

Vacation mode:

This operating mode can be used to save energy during

high cost energy periods, or when you won't be using your

appliance for an extended period of time by disabling the

lights, alarm tones, and keypad entry tones. Vacation mode

also serves as a Sabbath mode, disabling functions and its

controls in accordance with the weekly Sabbath and

religious holidays observed within the Orthodox Jewish

community. When used as Sabbath mode, you may open

or close the door at any time to access contents without

concern of directly turning on or off any lights, digital

readouts, solenoids, fans, valves, compressor, icons,

tones, or alarms.

When activated, the display, alarm indicators and tones,

keypad touch tones, interior lights, and all options are

disabled. All keypad functions are disabled, with the

exception of the "On/Off" keypad which is required to exit

Vacationmode. Storage compartment temperatures are

monitored and controlled at the settings prior to entering

Vacation mode.

To enter Vacation Mode (with the control out of sleep

mode), press and hold the "On/Off" keypad until the display

goes past "OFF" and reads "VAC". The display will flash

"VAC" 3-times to acknowledge your request, then will

display "VAC" continuously until Vacation mode is exited. A

power outage will not exit Vacation mode, exiting can only

be accomplished manually. To exit Vacation mode and

return to normal operation, press and hold the "On/Off"

keypad until the control displays the temperature.

ALARM RESET

Power Failure

ALARM RESET

Temp

NOTE

Door Ajar

Temp

could spoil perishables.

17

SHELVING CONFIGURATIONS

Refrigerator / Freezer

24" (61 cm) wide see Figure 13:

Refrigerator:

(2) Half width cantilever adjustable shelf. see Figure 14

(1) Full width fixed position glass shelf

(1) Roller glide clear crisper drawer Freezer:

(1) Fixed position metal shelf, see Figure 15.

Freezer

shelf

CARE AND CLEANING

18

Pull out until it stops. Lift up on the front of the pan,

and remove it from the frame.

SHELF REMOVAL

To Add or Remove a Shelf

Remove stored product from the shelf. Do not try to remove

a loaded shelf from the appliance. Grasp the shelf front with

both hands, rotate the front upward and lift out. (See Figure

17a). To install a shelf insert the shelf in the appliance and

insert the top hooks into the shelf support slots and drop

the shelf down so the hooks drop over the bottom of the

slots.

!

CAUTION

19

shelf.

Front Grille

Be sure that nothing obstructs the required air flow

openings in front of the cabinet. At least once or twice a

year, brush or vacuum lint and dirt from the front grille area

(see page 4).

SHOCK HAZARD: Disconnect electrical power from the

appliance before cleaning with soap and water.

Cabinet

The painted cabinet can be washed with either a mild soap

and water and thoroughly rinsed with clear water. NEVER

use abrasive scouring cleaners.

Interior

Wash interior compartment with mild soap and water. Do

NOT use an abrasive cleaner, solvent, polish cleaner or

undiluted detergent.

Care of Appliance

1. Avoid leaning on the door, you may bend the door

hinges or tip the appliance.

!

CAUTION

CARE AND CLEANING

20

2. Exercise caution when sweeping, vacuuming or

mopping near the front of the appliance. Damage to

the grille can occur.

3. Periodically clean the interior of the appliance as

needed.

4. Periodically check and/or clean the front grille as

needed.

In the Event of a Power Failure

If a power failure occurs, try to correct it as soon as

possible. Minimize the number of door openings while the

power is off so as not to adversely affect the appliance's

temperature.

Light assembly replacement

All models use LED lamps to illuminate the interior of the

appliance. This component is very reliable, but should one

fail, contact a qualified service technician for replacement

of the LED.

Outdoor Product Long-Term Storage /

Winterization: (MO24RF, refrigerator freezer):

1. Time to Winterize, when the daily low ambient

temperature is at or below 38°F (3.3°C).

Operation of the unit at ambient temperatures below the

recommended Winterization temperature will void your

warranty.

2. Turn unit off, (see page 11)

3. Remove all contents.

4. If necessary, move the unit so you can gain access to

the rear of the product.

5. Unplug the unit from the power outlet.

6. It is also recommended that the power to the outlet be

turned-off if the circuit is not required for other items

during the Winter season.

7. When cleaning unit pay particular attention to any

cracks and crevices that may have accumulated dirt

and debris.

8. Remove the front toe-grille, (see Figure 18), and use a

brush and vacuum to clean dirt and debris from

beneath the unit.

9. Thoroughly clean the toe-grille and re-install on the

unit. (See Figure 18).

10. Remove the rear access cover, (see Figure 19), and

use a brush and vacuum to clean dirt and debris from

the machine compartment.

• If the plastic defrost drain pan located under the

compressor contains water, use a sponge to

remove as much water as possible.

11. Thoroughly clean the rear access cover and re-install

on the unit.

12. Wipe down all interior surfaces with anti-bacterial

cleaner to be followed with clean rinse water to remove

any residual chemicals which could cause staining. Do

not use any abrasive cleaners or scouring pads.

13. Leave the door open and allow to completely dry out

before closing the door.

14. Thoroughly clean the door gasket with anti-bacterial

cleaner to be followed with clean rinse water to remove

any residual chemicals.

15. Thoroughly clean the exterior with a cleaner approved

for stainless steel. Do not use any abrasive cleaners

or scouring pads. See "Stainless Steel Maintenance"

on page 20.

16. Any mounting hardware / fasteners that are showing

signs of corrosion should be replaced.

17. Once the exterior has been thoroughly cleaned, you

may want to apply a coating of car wax to help protect

against spotting from moisture, dirt, and debris that

may accumulate on the surfaces during the

Winterization period.

!

CAUTION

La page charge ...

Marvel MORF224SS31A Manuel utilisateur

Ce manuel convient également à

Marvel MORF224SS31A Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents