Ryobi P545 Manuel utilisateur

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

18 VOLT CHAIN SAW

SCIE À CHAÎNE 18 V

MOTOSIERRA DE 18 V

P542

ACCEPTS ALL ONE+ BATTERY PACKS

COMPATIBLE AVEC TOUS LE BATTERIES ONE+

ACEPTA TODOS LOS PAQUETES DE BATERÍAS ONE+

Cette scie à chaîne a été conçue et fabriquée conformément

aux strictes normes de fiabilité, simplicité d’emploi et sécurité

d’utilisation. Correctement entretenue, elle vous donnera des années

de fonctionnement robuste et sans problème.

AVERTISSEMENT : Pour réduire les risques de

blessures, l’utilisateur doit lire et veiller à bien comprendre le

manuel d’utilisation avant d’employer ce produit.

Merci de votre achat.

Su motosierra inalámbrica ha sido diseñada y fabrica-

da de conformidad con nuestras estrictas normas para

brindar fiabilidad, facilidad de uso y seguridad para el opera-

dor. Con el debido cuidado, le brindará muchos años de sólido

y eficiente funcionamiento.

ADVERTENCIA: Para reducir el riesgo de lesiones,

el usuario debe leer y comprender el manual del operador antes

de usar este producto.

Le agradecemos su compra.

CONSERVER CE MANUEL POUR

FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL PARA

FUTURAS CONSULTAS

SAVE THIS MANUAL FOR FUTURE REFERENCE

Your chain saw has been engineered and manufactured to our high standard for dependability, ease of operation, and

operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using

this product.

Thank you for your purchase.

2

 Introduction .......................................................................................................................................2

Introduction / Introducción

 General Safety Rules ..................................................................................................................... 3-5

Règles de sécurité générales / Reglas de seguridad generales

 Specific Safety Rules ........................................................................................................................6

Règles de sécurité particulières / Reglas de seguridad específicas

Symbols ........................................................................................................................................ 7-8

Symboles / Símbolos

 Features .............................................................................................................................................9

Caractéristiques / Características

 Assembly .........................................................................................................................................10

Assemblage / Armado

 Operation ................................................................................................................................... 10-18

Utilisation / Funcionamiento

 Maintenance .............................................................................................................................. 19-24

Entretien / Mantenimiento

 Troubleshooting ...............................................................................................................................25

Dépannage / Corrección de problemas

 Warranty ..........................................................................................................................................26

Garantie / Garantía

 Parts Ordering and Service ............................................................................................... Back Page

Commande de pièces et réparation / Pedidos de piezas y servicio ......................................................... Page arrière / Pág. posterior

TABLE OF CONTENTS

TABLE DES MATIÈRES / ÍNDICE DE CONTENIDO

INTRODUCTION

INTRODUCTION / INTRODUCCIÓN

This product has many features for making its use more pleasant and enjoyable. Safety, performance,

and dependability have been given top priority in the design of this product making it easy to maintain

and operate.

* * *

Ce produit offre de nombreuses fonctions destinées à rendre son utilisation plus plaisante et satisfai-

sante. Lors de la conception de ce produit, l’accent a été mis sur la sécurité, les performances et la

fiabilité, afin d’en faire un outil facile à utiliser et à entretenir.

* * *

Este producto ofrece numerosas características para hacer más agradable y placentero su uso. En el

diseño de este producto se ha conferido prioridad a la seguridad, el desempeño y la fiabilidad, por lo

cual se facilita su manejo y mantenimiento.

3 - English

GENERAL SAFETY RULES

READ ALL INSTRUCTIONS

BASIC SAFETY PRECAUTIONS

 Do not operate a chain saw with one hand! Use

a firm grip with thumbs and fingers encircling the

chain saw handles. Serious injury to the operator,

helpers, bystanders, or any combination of these

persons may result from one-handed operation.

A chain saw is intended for two-handed use.

 Always be aware of what you are doing when

using the chain saw. Use common sense. Do

not operate the chain saw when you are tired,

ill, or under the influence of alcohol, drugs, or

medication.

 Stay alert and pay attention to what you are

doing. Use common sense when using this unit.

 Keep all parts of your body away from the saw

chain when the unit is running.

 Always carry the chain saw by the front handle

with the unit stopped and the guide bar and saw

chain positioned to the rear. When transporting

your chain saw, use the appropriate guide bar

scabbard.

 Never let anyone use your chain saw who has

not received adequate instructions in its proper

use. This applies to rentals as well as privately

owned saws.

 Before you start the unit, make sure the saw

chain is not contacting any object.

 Stop the chain saw before setting it down. Do

not leave the unit running unattended.

 To avoid accidental starting, never carry the unit

with your finger on the switch trigger.

 Maintain the unit with care. Keep the cutting

edge sharp and clean for best performance

and to reduce the risk of injury. Follow instruc-

tions for lubricating and changing accessories.

Inspect the battery charger cord periodically,

and if damaged, have it replaced or repaired by

an authorized service dealer.

WARNING:

Do not attempt to operate this unit until you

have read thoroughly and understand com-

pletely all instructions, safety information, etc.

contained in this manual. Failure to comply can

result in accidents involving fire, electric shock,

or serious personal injury.

 Keep handles dry, clean, and free of oil and

grease.

 Do not operate a chain saw that is damaged,

improperly adjusted, or not completely and

securely assembled. Chain should stop turning

when the switch trigger is released. If the chain

turns after the switch trigger has been released,

have the unit serviced by your nearest Ryobi

service dealer.

 Check for damaged parts. Any part or guard that

has been damaged should be carefully checked

to determine that it will operate properly and

perform its intended function. Check for align-

ment of moving parts, binding of moving parts,

breakage of parts, mounting, and any other

conditions that may affect its operation. A guard

or other part that is damaged should be properly

repaired or replaced by an authorized service

dealer unless otherwise indicated elsewhere in

this manual.

 All chain saw service, other than the items listed

in the operation and maintenance sections,

should be performed by your nearest Ryobi

service dealer.

 Do not use in the rain, snow or wet conditions.

 Always maintain a proper stance. Do not over-

reach.

 Do not adapt your powerhead to a bow guide

or use it to power any attachments or devices

not listed for the saw.

 Do not cut vines and/or small underbrush.

SAFETY APPAREL

 Wear snug fitting clothing. Always wear heavy,

long pants, long sleeves, overalls, jeans or

chaps made of cut resistant material or ones

that contain cut resistant inserts. Wear non-

slip safety footwear. Wear non-slip heavy duty

gloves to improve your grip and to protect your

hands. Do not wear jewelry, short pants, san-

dals, or go barefoot. Do not wear loose fitting

clothing, which could be drawn into the motor

or catch the chain or underbrush. Secure hair

so it is above shoulder level.

 Wear eye protection which is marked to comply

with ANSI Z87.1 as well as hearing and head

protection when operating this equipment.

4 - English

GENERAL SAFETY RULES

KICKBACK

See Figures 1 - 3.

 WARNING: Kickback may occur when the

moving chain contacts an object at the upper

portion of the tip of the guide bar or when the

wood closes in and pinches the saw chain in

the cut. Contact at the upper portion of the tip

of the guide bar can cause the chain to dig into

the object and stop the chain for an instant.

The result is a lightning fast, reverse reaction

which kicks the guide bar up and back toward

the operator. If the saw chain is pinched along

the top of the guide bar, the guide bar can be

driven rapidly back toward the operator. Either

of these reactions can cause loss of saw control

which can result in serious injury. Do not rely

exclusively upon the safety devices built into

the saw. As a chain saw user, you should take

several steps to keep your cutting jobs free from

accident or injury.

 The following precautions should be followed

to minimize kickback:

1. Hold the saw firmly with both hands when

the motor is running. Place your right hand

on the rear handle and your left hand on the

front handle with your thumbs and fingers

encircling the chain saw handles. A firm grip

together with a stiff left arm will help you

maintain control of the saw if kickback occurs.

2. Make sure that the area in which you are cut-

ting is free from obstructions. Do not let the

nose of the guide bar contact a log, branch,

fence, or any other obstruction that could be

hit while you are operating the saw.

3. Always cut with the unit running at full speed.

Fully squeeze the switch trigger and maintain

a steady cutting speed.

4. Use replacement parts such as low kickback

chain and special guide bars that reduce the

risks associated with rotational kickback.

Use only the replacement guide bars and low

kickback chains specified by the manufacturer

for the saw.

 With a basic understanding of kickback, you

can reduce or eliminate the element of surprise.

Sudden surprise contributes to accidents.

 Keep proper footing and balance at all times.

 Do not cut above shoulder height or overreach when

cutting.

 Follow the sharpening and maintenance instruc-

tions for the saw chain.

 Push and Pull - This reaction force is always

opposite to the direction the chain is moving

where wood contact is made. Thus, the operator

must be ready to control the PULL when cutting

on the bottom edge of the bar, and PUSH when

cutting along the top edge. See Figure 3.

Fig. 1

Fig. 2

Fig. 3

ROTATIONAL

KICKBACK

DANGER ZONE

PULL

PUSH

5 - English

IN THE CUTTING/WORK AREA

 Do not operate a chain saw in a tree, on a ladder,

rooftop or scaffold; this is extremely dangerous.

 Keep ALL children, bystanders, visitors, and

animals out of the work area while starting or

cutting with the chain saw.

NOTE: The size of the work area depends on the

job being performed as well as the size tree or work

piece involved. For example, felling a tree requires

a larger work area than making bucking cuts.

 Never start cutting until you have a clear work

area, secure footing, and a planned retreat path

from the falling tree. Cluttered area invite injuries.

 Do not expose the chain saw to rain.

 Do not use the chain saw in damp or wet locations.

 Do not use the chain saw near flammable liq-

uids, gases, or in any type of explosive atmo-

sphere.

 Use extreme caution when cutting small size

brush and saplings, because slender mate-

rial may catch the saw chain and be whipped

toward you or pull you off balance.

 When cutting a limb that is under tension, be

alert for spring back so that you will not be

struck when the tension in the wood fibers is

released.

 Do not force the chain saw. The job can be per-

formed better and safer at the rate for which it

was intended.

 Always use the right product for your applica-

tion. The chain saw should be used for cutting

wood only. Never use the chain saw to cut plas-

tic, masonry or non-wood building materials.

 Do not use the chain saw for purposes not

intended.

GENERAL SAFETY RULES

 Store idle chain saw when not in use. Chain saw

should be stored in a dry and high or locked area

out of the reach of children. When storing chain

saw, remove battery and place the scabbard on

the bar and chain or store the chain saw in a

carry case.

 Remove the battery pack from the chain saw

before cleaning, servicing, storing, removing

material from the unit, changing accessories

such as the bar and chain, or when not in use.

UNDERSTANDING YOUR CHAIN SAW

SAFETY DEVICES

LOW KICKBACK SAW CHAIN

The rakers (depth gauges) ahead of each cutter

can minimize the force of a kickback reaction by

preventing the cutters from digging in too deeply at

the kickback zone. Only use replacement chain that

is equivalent to original chain or has been certified

as low kickback chain per ANSI B175.1.

Low kickback saw chain is chain that has met

the kickback performance requirements of ANSI

B175.1 - 1991 (American National Standard for

Power Tools - Gasoline-Powered Chain Saws-

Safety Requirements) when tested on the repre-

sentative sample of chain saws below 3.8 c.i.d.

specified in ANSI B175.1 - 1991.

As saw chains are sharpened during their useful

life, they lose some of the low kickback qualities

and extra caution should be used.

GUIDE BARS

Generally, guide bars with small radius tips have

somewhat lower kickback potentials.

When making a replacement, be sure to order one

of the Ryobi bars listed for the saw in this opera-

tor’s manual.

6 - English

BATTERY SAFETY

 Battery operated units do not have to be plugged

into an electrical outlet; therefore, they are

always in operating condition. Be aware of pos-

sible hazards even when unit is not operating.

 Remove the battery pack from the chain saw

before cleaning, servicing, storing, removing

material from the unit, changing accessories

such as the bar and chain, or when not in use.

 A battery pack must be recharged only with the

specified charger for the battery pack. A charger

that may be suitable for one type of battery pack

may create a risk of fire when used with another

battery pack. Use battery pack only with charger

listed.

 For use with 18V nickel-cadmium and 18 V

lithium-ion battery packs, see tool/appliance/

battery pack/charger correlation supplement

987000-432.

 To reduce the risk of explosion and possible

injury, Do not place battery units or their batteries

near fire or heat.

 Do not open or mutilate the battery pack.

Released electrolyte is corrosive and may cause

damage to the eyes or skin. It may be toxic if

swallowed.

 Do not crush, drop or damage battery pack. Do

not use a battery pack or charger that has been

dropped or received a sharp blow. A damaged

battery is subject to explosion. Properly dispose

of a dropped or damaged battery immediately.

 Batteries can explode in the presence of a

source of ignition, such as a pilot light. To reduce

the risk of serious personal injury, never use any

SPECIFIC SAFETY RULES

cordless product in the presence of open flame.

An exploded battery pack can propel debris and

chemicals. If exposed, flush with water imme-

diately.

 Do not charge unit in a damp or wet location.

Following this rule will reduce the risk of electric

shock.

 For best results, your battery unit should be

charged in a location where the temperature

is more than 50°F but less than 100°F. Do not

store outside or in vehicles.

 Under extreme usage or temperature condi-

tions, battery pack leakage may occur. If liquid

comes in contact with your skin, wash imme-

diately with soap and water. If liquid gets into

your eyes, flush them with clean water for at

least 10 minutes, then seek immediate medical

attention.

 Do not dispose of batteries in a fire. The cell

may explode. Batteries should be recycled, con-

sult your local waste authority for information

regarding available recycling and/or disposal

options.

 When battery pack is not in use, keep it away

from other metal objects like: paper clips, coins,

keys, nails, screws, or other small metal objects

that can make a connection from one terminal

to another. Shorting the battery pack terminals

together may cause sparks, burns, or a fire.

 Save these instructions. Refer to them frequently

and use them to instruct others who may use

this tool. If you loan someone this tool, loan

them these instructions also.

7 - English

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their

meaning. Proper interpretation of these symbols will allow you to operate the product better and

safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual

To reduce the risk of injury, user must read and

understand operator’s manual before using this

product.

Eye, Hearing, and Head

Protection

Always wear eye protection with side shields marked to

comply with ANSI Z87.1, along with hearing and head

protection

Wet Conditions Alert Do not expose to rain or use in damp locations.

Operate With Two

Hands

Hold and operate the saw properly with both hands.

One Handed Do not operate the saw using only one hand.

The following signal words and meanings are intended to explain the levels of risk associated with

this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates an imminently hazardous situation, which, if not

avoided, will result in death or serious injury.

WARNING:

Indicates a potentially hazardous situation, which, if not avoided,

could result in death or serious injury.

CAUTION:

Indicates a potentially hazardous situation, which, if not avoided,

may result in minor or moderate injury.

CAUTION:

(Without Safety Alert Symbol) Indicates a situation that may

result in property damage.

8 - English

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their

meaning. Proper interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Kickback DANGER! Beware of kickback.

Bar Nose Contact Avoid bar nose contact.

Wear Gloves

Wear non-slip, heavy-duty protective gloves when

handling the chain saw.

Wear Safety Footwear

Wear non-slip safety footwear when using this

equipment.

Keep Bystanders

Away

Keep all bystanders and animals at least 50 ft. away.

Li - Ion

Recycle Symbols

This product uses lithium-ion or nickel-cadmium

batteries. Local, state or federal laws may prohibit

disposal of batteries in ordinary trash. Consult your

local waste authority for information regarding available

recycling and/or disposal options.

V Volts Voltage

Direct Current Type or a characteristic of current

9 - English

FEATURES

PRODUCT SPECIFICATIONS

Motor .................................................. 18 Volt DC

Bar Length .................................................. 10 in.

Replacement Bar

Part Number ...........671256002 or 671834007

Replacement Chain

Part Number ...............6958301 or 690583002

NOTE: This saw was designed for occasional light

duty use and has some limitations as to what it

can cut.

KNOW YOUR CHAINSAW

See Figure 4.

The safe use of this product requires an

understanding of the information on the product and

in this operator’s manual as well as a knowledge

of the project you are attempting. Before use of

this product, familiarize yourself with all operating

features and safety rules.

Fig. 4

CHAIN OIL

TANK CAP

REAR

HANDLE

FRONT HANDLE

BAR

CHAIN

BATTERY PACK

HEX KEY

STORAGE AREA

HAND GUARD

SwITCH TRIGGER

SCABBARD

BATTERY PACK

LOCK-OUT

BUTTON

10 - English

WARNING:

Do not allow familiarity with this product to

make you careless. Remember that a careless

fraction of a second is sufficient to inflict seri-

ous injury.

WARNING:

Always wear eye protection with side shields

marked to comply with ANSI Z87.1, along with

hearing and head protection. Failure to do so

could result in objects being thrown into your

eyes resulting in possible serious injury.

ASSEMBLY

UNPACKING

This product has been shipped completely

assembled.

 Carefully remove the product and any acces-

sories from the box. Make sure that all items

listed in the packing list are included.

WARNING:

Do not use this product if it is not completely

assembled or if any parts appear to be missing

or damaged. Use of a product that is not prop-

erly and completely assembled could result in

serious personal injury.

 Inspect the product carefully to make sure no

breakage or damage occurred during ship-

ping.

 Do not discard the packing material until you

have carefully inspected and satisfactorily oper-

ated the product.

 If any parts are damaged or missing, please call

1-800-860-4050 for assistance.

PACKING LIST

Chain Saw with Scabbard

Hex Key

Bar and Chain Lubricant

Battery Pack

Charger

Operator’s Manual

WARNING:

If any parts are damaged or missing do not

operate this product until the parts are replaced.

Use of this product with damaged or missing

parts could result in serious personal injury.

WARNING:

Do not attempt to modify this product or cre-

ate accessories not recommended for use with

this product. Any such alteration or modifica-

tion is misuse and could result in a hazardous

condition leading to possible serious personal

injury.

WARNING:

To prevent accidental starting that could cause

serious personal injury, always remove the bat-

tery pack from the product when assembling

parts.

OPERATION

WARNING:

Do not use any attachments or accessories

not recommended by the manufacturer of this

product. The use of attachments or accessories

not recommended can result in serious personal

injury.

Before each use, inspect the entire product for

damaged, missing, or loose parts such as screws,

nuts, bolts, caps, etc. Tighten securely all fasteners

and caps and do not operate this product until all

missing or damaged parts are replaced. Please call

1-800-860-4050 or contact an authorized service

center for assistance.

11 - English

OPERATION

CAUTION:

Remove battery pack from unit. Fill oil tank with

Ryobi Bar and Chain Lubricant before starting

the chain saw. Failure to lubricate the chain will

cause damage to the bar and chain.

CHAIN OIL SYSTEM

See Figure 6.

 Use Ryobi Bar and Chain Lubricant. It is formu-

lated to perform over a wide temperature range

with no dilution required.

NOTE: Do not use dirty, used or otherwise contam-

inated oils. Damage may occur to the bar or chain.

 Carefully pour the bar and chain oil into the tank.

 Check and fill the oil tank when battery is

recharged, or as needed.

 Depress the oil tank cap several times to pump

the oil to the chain before starting the saw.

 Depress the oil tank cap every 20-30 seconds

while cutting to keep the chain lubricated.

NOTE: It is normal for lubricant to seep from the

saw when not in use. To prevent seepage, empty

the oil tank after each use. When storing the unit

for a long period of time (three months or longer) be

sure the chain is lightly lubricated; this will prevent

rust on the chain and bar sprocket.

APPLICATIONS

You may use this product for the following pur-

poses:

Limbing and pruning branches from trees

Felling small trees up to 7 in. diameter

Bucking the fallen tree into shorter lengths

This product will accept Ryobi One+ 18 V lithium-

ion battery packs and Ryobi One+ 18 V nickel-

cadmium battery packs.

For complete charging instructions, refer to the

Operator’s Manual for your Ryobi One+ battery

pack and charger models.

TO INSTALL / REMOVE BATTERY PACK

See Figure 5.

WARNING:

Always remove battery pack from your tool

when you are assembling parts, making adjust-

ments, cleaning, carrying, transporting or when

not in use. Removing battery pack will prevent

accidental starting that could cause serious

personal injury.

NOTE: To avoid serious personal injury, always

remove the battery pack and keep hands clear of

the look-out button when carrying or transporting

the tool.

To install:

 Place the battery pack in your chain saw. Align

raised rib on battery pack with groove in chain

saw’s battery port.

 Make sure the latches on each side of the bat-

tery pack snap in place and that battery pack is

secured in chain saw before beginning operation.

To remove:

Locate latches on side of battery pack and depress

both sides to release the battery pack from the

chain saw.

CAUTION:

When placing battery pack in your chain saw,

be sure raised rib on battery pack aligns with

groove in chain saw’s battery port and latches

snap in place properly. Improper assembly of

battery pack can cause damage to internal

components.

Fig. 6

Fig. 5

BATTERY

PACK

LATCHES

BATTERY

PORT

12 - English

OPERATION

STARTING AND STOPPING THE CHAIN

SAW

See Figure 7.

WARNING:

Keep body to the left of the chain line. Never

straddle the saw or chain, or lean over past the

chain line.

Starting the chain saw:

 Place the chain saw on a flat bare surface and

make sure no objects or obstructions are in

immediate vicinity which could come in contact

with the bar and chain.

 Press and hold the lock-out button. This makes

the switch trigger operational.

 Press and hold the switch trigger, release the

lock-out button and continue to squeeze the

switch trigger for continued operation.

Stopping the chain saw:

 Release the switch trigger to stop the chain

saw.

 Upon release of the switch trigger, the lock-out

button will be automatically reset to the lock

position.

This cordless chain saw is not designed for cutting

trees larger than 5 in. in diameter.

This cordless chain saw is designed for limbing

and pruning type cutting, as well as cutting trees

up to 5 in. in diameter only.

PREPARATION FOR CUTTING

PROPER GRIP ON HANDLES

See Figures 8 - 10.

Refer to IMPORTANT SAFETY INSTRUCTIONS

earlier in this manual for appropriate safety equip-

ment.

 Wear non-slip gloves for maximum grip and

protection.

 Hold the saw firmly with both hands. Always

keep your left hand on the front handle and your

right hand on the rear handle so that your body

is to the left of the chain line.

Fig. 7

LOCK-OUT

BUTTON

SwITCH

TRIGGER

LOCK-OUT BUTTON

SwITCH

TRIGGER

13 - English

WARNING:

Never use a left-handed (cross-handed) grip,

or any stance which would place your body or

arm across the chain line.

 Maintain a proper grip on the saw whenever

the unit is running. The fingers should encircle

the handle and the thumb is wrapped under the

handlebar. This grip is least likely to be broken

(by a kickback or other sudden reaction of the

saw). Any grip in which the thumb and fingers

are on the same side of the handle, is danger-

ous because a slight kick of the saw can cause

loss of control.

WARNING:

Do not operate the switch trigger with your left

hand and hold the front handle with your right

hand. Never allow any part of your body to be

in the chain line while operating a saw.

OPERATION

CHAIN LINE

Fig. 10

Fig. 9

Fig. 8

14 - English

OPERATION

ers.Trees should not be felled in a manner that

would endanger any person, strike any utility

line or cause any property damage. If the tree

does make contact with any utility line, the utility

company should be notified immediately.

 Always cut with both feet on solid ground to

prevent being pulled off balance.

 Do not cut above chest height, as a saw held high-

er is difficult to control against kickback forces.

 Do not fell trees near electrical wires or build-

ings. Leave this operation for professionals.

 Cut only when visibility and light are adequate

for you to see clearly.

TREE FELLING

See Figures 12 - 15.

Unusual Hazardous Tree Felling Conditions

Do not fell trees during periods of high wind or

heavy precipitation. Wait to do your cutting until

the hazard has ended.

WARNING:

Do not cut down trees having an extreme lean or

trees that have rotten limbs, loose bark, or hol-

low trunks. Have these trees pushed or dragged

down with heavy equipment, then cut them up.

DANGER:

Electrocution hazard. Do not cut trees or

branches near power lines or electrical wires.

Contact with power lines or live electrical wires

will result in serious personal injury or possible

death.

PROPER CUTTING STANCE

See Figure 11.

 Weight should be balanced with both feet on

solid ground.

 Keep left arm with elbow locked in a “straight

arm” position to withstand any kickback force.

 Your body should always be to the left of the

chain line.

 Thumb should be on underside of handlebar.

BASIC CUTTING PROCEDURE

Practice cutting a few small logs using the following

technique to get the “feel” of using the saw before

you begin a major sawing operation.

 Take the proper stance in front of the wood with

the saw off.

 Squeeze the switch trigger and let the chain

accelerate to full speed before entering the

cut.

 Begin cutting with the saw against the log.

 Keep the unit running the entire time you are

cutting, maintain a steady speed.

 Allow the chain to cut for you; exert only light

downward pressure. If you force the cut, dam-

age to the bar, chain, or unit can result.

 Release the switch trigger as soon as the cut

is completed, allowing the chain to stop. If you

run the saw without a cutting load, unnecessary

wear can occur to the chain, bar, and unit.

 Do not put pressure on the saw at the end of cut.

WORK AREA PRECAUTIONS

 Cut only wood or materials made from wood,

no sheet metal, no plastics, no masonry, no

non-wood building materials.

 Never allow children to operate the saw. Allow

no person to use this chain saw who has not

read this Operator’s Manual or received ade-

quate instructions for the safe and proper use

of this chain saw.

 When felling a tree, keep everyone - helpers,

bystanders, children, and animals - a safe

distance from the cutting area. During felling

operations, the safe distance should be a least

twice the height of the largest trees in the fell-

ing area. During bucking operations, keep a

minimum distance of 15 feet between work-

Fig. 11

STRAIGHT ARM

POSITION

CHAIN LINE

15 - English

OPERATION

WARNING:

Do not cut trees or branches near buildings,

which may result in serious injuries or property

damage.

WARNING:

Check the tree for damaged or dead branches

that could fall and hit you during felling.

WARNING:

Periodically glance at the top of the tree during

the backcut to assure the tree is going to fall in

the desired direction.

WARNING:

If the tree starts to fall in the wrong direction,

or if the saw gets caught or hung up during the

fall, leave the saw and save yourself!



Felling a tree - When bucking and felling opera-

tions are being performed by two or more per-

sons, at the same time, the felling operation

should be separated from the bucking operation

by a distance of at least twice the height of the

tree being felled. Trees should not be felled in a

manner that would endanger any person, strike

any utility line or cause any property damage. If

the tree does make contact with any utility line, the

utility company should be notified immediately.

 Before any cuts are started, pick your escape

route (or routes in case the intended route is

blocked); clear the immediate area around the

tree and make sure there are no obstructions

in your planned path of retreat. Clear path of

safe retreat approximately 135° from planned

line of fall. The retreat path should extend back

and diagonally to the rear of the expected line

of fall. See Figure 12.

 Before felling is started, consider the force and

direction of the wind, the lean and balance of

the tree, and the location of large limbs. These

things influence the direction in which the tree

will fall. Do not try to fell a tree along a line dif-

ferent from its natural line of fall.

 The chain saw operator should keep on the

uphill side of the terrain as the tree is likely to

roll or slide downhill after it is felled.

 Remove dirt, stones, loose bark, nails, staples,

and wire from the tree where felling cuts are to

be made.

 Notched Undercut. Cut a notch about 1/3 the

diameter of the tree, perpendicular to the direc-

tion of fall. Make the cuts of the notch so they

intersect at a right angle to the line of fall. This

notch should be cleaned out to leave a straight

line. To keep the weight of the wood off the saw,

always make the lower cut of the notch before

the upper cut. See Figure 13.

90°

PLANNED PATH OF SAFE RETREAT 135° FROM PLANNED

LINE OF FALL

PLANNED LINE OF FALL

SAFE

RETREAT

ZONE

PLANNED

LINE OF FALL

Fig. 12

SAFE

RETREAT

ZONE

45°

90°

135°

SAFE

RETREAT

ZONE

HINGE

2 in. OR 1/10 DIA

NOTCH -

APPROX. 1/3

DIAMETER OF

TRUNK

BACK CUT

2 in.

Fig. 13

16 - English

 Felling Backcut. The backcut is always made lev-

el and horizontal, and at a minimum of 2 in. above

the horizontal cut of the notch. See Figures 13 - 14.

 Never cut through to the notch. Always leave a

band of wood between the notch and backcut

(approximately 2 in. or 1/10 the diameter of the

tree). This is called “hinge” or “hingewood.” It

controls the fall of the tree and prevents slip-

ping or twisting or shoot-back of the tree off the

stump. See Figures 13 - 14.

 On large diameter trees, stop the back cut

before it is deep enough for the tree to either

fall or settle back on the stump. Then insert

soft wooden or plastic wedges into the cut so

they do not touch the chain. The wedges can

be driven in, little by little, to help jack the tree

over. See Figure 15.



As tree starts to fall, stop the chain saw and put

it down immediately. Retreat along the cleared

path, but watch the action in case something

falls your way. Be alert for overhead limbs or

branches that may fall and watch your footing.

WARNING:

Never cut through to the notch when making a

backcut. The hinge controls the fall of the tree,

this is the section of wood between the notch

and backcut.

BUCKING

See Figures 16 - 19.

Bucking is the term used for cutting a fallen tree

to the desired log length.

 Always make sure your footing is secure and

your weight is distributed evenly on both feet.

 Cut only one log at a time.

 Support small logs on a saw horse or another

log while bucking.

 Keep a clear cutting area. Make sure that no objects

can contact the guide bar nose and chain during

cutting, this can cause kickback. Refer to Precau-

tions Against Kickback earlier in this manual.

 When bucking on a slope, always stand on the

uphill side of the log. To maintain complete con-

trol of the chain saw when cutting through the log,

release the cutting pressure near the end of the

cut without relaxing your grip on the chain saw

OPERATION

NOTCH

BACK CUT

Fig. 15

Fig. 14

KICKBACK

Fig. 16

HINGE

wEDGE

Fig. 17

17 - English

OPERATION

handles. Do not let the chain contact the ground.

After completing the cut, wait for the saw chain

to stop before you move the chain saw. Always

stop the motor before moving from tree to tree.

 Sometimes it is impossible to avoid pinching

(with just standard cutting techniques) or difficult

to predict which way a log will settle when cut.

To avoid pinching while cutting, rotate or move

the log so that the pinch is eliminated.

BUCKING LOGS UNDER STRESS

See Figures 18 - 19.

When the log is supported along its entire length,

it should be cut from the top or overbucking.

When the log is supported on one end, cut 1/3

the diameter from the underside or underbuck-

ing. Then make the finishing cut by overbucking

to meet the first cut.

As the log is being cut, it will tend to bend. The saw

can become pinched or hung in the log if you make

the first cut deeper than 1/3 of the diameter of the log.

Give special attention to logs under stress to pre-

vent the bar and chain from pinching.

When bucking on a slope, always stand on the uphill

side of the log as shown in figure 18. When “cutting

through,” to maintain complete control of the chain

saw, release the cutting pressure near the end of

the cut without relaxing your grip on the chain saw

handles. Do not let the chain contact the ground.

After completing the cut, wait for the saw chain

to stop before you move the chain saw. Always

stop the motor before moving from tree to tree.

TYPES OF CUTTING USED

See Figure 19.

OVERBUCKING

Begin on the top side of the log with the bottom

of the saw against the log; exert light pressure

downward. Note that the saw will tend to pull

away from you.

UNDERBUCKING

Begin on the under side of the log with the top

of the saw against the log; exert light pressure

upward. During underbucking, the saw will tend

to push back at you. Be prepared for this reaction

and hold the saw firmly to maintain control.

WARNING:

Never climb into a tree to limb or prune. Do not

stand on ladders, platforms, a log, or in any

position which can cause you to lose your bal-

ance or control of the saw.

LOAD

FINISHING CUT

1ST CUT

1/3 DIA

LOG SUPPORTED AT ONE END:

LOG SUPPORTED AT BOTH ENDS:

FINISHING CUT

1ST CUT 1/3 DIA

LOAD

Fig. 18

OvERBUCKING

UNDERBUCKING

Fig. 19

18 - English

OPERATION

LIMBING

See Figure 20.

Limbing is removing branches from a fallen tree.

 Work slowly, keeping both hands on the chain

saw with a firm grip. Always make sure your

footing is secure and your weight is distributed

evenly on both feet.

 Leave the larger support limbs under the tree to

keep the tree off the ground while cutting.

 Limbs should be cut one at a time. Remove the

cut limbs from the work area often to help keep

the work area clean and safe.

 Branches under tension should be cut from the

bottom up to avoid binding the chain saw.

 Keep the tree between you and the chain saw

while limbing. Cut from the side of the tree

opposite the branch you are cutting.

PRUNING

See Figure 21.

Pruning is trimming limbs from a live tree.

 Work slowly, keeping both hands on the chain

saw with a firm grip. Always make sure your

footing is secure and your weight is distributed

evenly on both feet.

 Do not cut from a ladder, this is extremely dan-

gerous. Leave this operation for professionals.

 Do not cut above chest height as a saw held

higher is difficult to control against kickback.

 When pruning trees it is important not to make

the finishing cut next to the main limb or trunk

until you have cut off the limb further out to

reduce the weight. This prevents stripping the

bark from the main member.

 Underbuck the branch 1/3 through for your first cut.

 Your second cut should overbuck to drop the

branch off.

 Now make your finishing cut smoothly and

neatly against the main member so the bark will

grow back to seal the wound.

WARNING:

If the limbs to be pruned are above chest height,

hire a professional to perform the pruning.

SPRINGPOLES

See Figure 22.

A springpole is any log, branch, rooted stump, or

sapling which is bent under tension by other wood

so that it springs back if the wood holding it is cut

or removed. On a fallen tree, a rooted stump has

a high potential of springing back to the upright

position during the bucking cut to separate the log

from the stump. Watch out for springpoles, they

are dangerous.

WARNING:

Springpoles are dangerous and could strike the

operator, causing the operator to lose control

of the chain saw. This could result in severe or

fatal injury to the operator.

FINISHING CUT

FIRST CUT

1/3 DIAMETER

SECOND CUT

LOAD

Fig. 21

SPRINGPOLE

Fig. 22

Fig. 20

CUT LIMBS ONE AT A TIME AND LEAvE SUPPORT LIMBS

UNDER TREE UNTIL LOG IS CUT

4

1

3

2

19 - English

MAINTENANCE

WARNING:

When servicing, use only identical replacement

parts. Use of any other parts may create a

hazard or cause product damage.

WARNING:

To avoid serious personal injury, always remove the

battery pack from the product when cleaning

or performing any maintenance.

GENERAL MAINTENANCE

Before each use, inspect the entire product for

damaged, missing, or loose parts such as screws,

nuts, bolts, caps, etc. Tighten securely all fasteners

and caps and do not operate this product until all

missing or damaged parts are replaced. Please call

1-800-860-4050 or contact an authorized service

center for assistance.

Avoid using solvents when cleaning plastic parts.

Most plastics are susceptible to damage from

various types of commercial solvents and may be

damaged by their use. Use clean cloths to remove

dirt, dust, oil, grease, etc.

WARNING:

Do not at any time let brake fluids, gasoline,

petroleum-based products, penetrating

oils, etc., come in contact with plastic

parts. Chemicals can damage, weaken or

destroy plastic which may result in serious

personal injury.

Only the parts shown on the parts list are intended

to be repaired or replaced by the customer. All

other parts should be replaced at an Authorized

Service Center.

BATTERY PACK REMOVAL AND

PREPARATION FOR RECYCLING

WARNING:

Upon removal, cover the battery pack’s ter-

minals with heavy-duty adhesive tape. Do not

attempt to destroy or disassemble battery pack

or remove any of its components. Lithium-ion

and nickel-cadmium batteries must be recycled

or disposed of properly. Also, never touch both

terminals with metal objects and/or body parts

as short circuit may result. Keep away from

children. Failure to comply with these warnings

could result in fire and/or serious injury.

20 - English

REPLACING BAR AND CHAIN

See Figures 23 - 27.

WARNING:

Remove the battery pack from the chain saw

and make sure the chain has stopped before

you do any work on the saw. Failure to do so

may result in accidental starting and possible

serious injury.

WARNING:

The safety instructions in this section are to

protect the user from serious personal injury.

CAUTION:

Always wear gloves when handling the bar and

chain; these components are sharp and may

contain burrs.

WARNING:

Never touch or adjust the chain while the motor

is running. The saw chain is very sharp; always

wear protective gloves when performing main-

tenance to the chain to avoid possible serious

lacerations.

 Remove the battery pack before you do any

work on the chain saw.

 Remove the hex key from the storage area and

use it to remove the chain cover screw, washer

and chain cover from the chain saw.

 Remove the bar and chain from mounting surface.

 Remove the old chain from the bar.

 Lay out the new saw chain in a loop and

straighten any kinks. The cutters should face in

the direction of chain rotation. If they face the

opposite direction, turn the loop over.

 Place the chain drive links into the bar groove.

Position the chain so there is a loop at the back of

the bar. Hold the chain in position on the bar and

place the loop around the sprocket of the chain

saw. Fit the bar flush against the mounting surface

so that the bar stud is in the long slot of the bar.

NOTE: When placing the bar on the bar stud,

assure that the adjusting pin is in the chain ten-

sion pin hole.

MAINTENANCE

RECOMMENDED BAR AND CHAIN

COMBINATIONS

Bar Part Number - 10 in.

671256002 or 671834007

Chain Part Number

6958301 or 690583002

Fig. 23

Fig. 24

Fig. 25

CHAIN

TENSIONING

SCREw

BAR

GROOvE

CHAIN DRIvE

LINKS

ADjUSTING

BAR

wASHER

CHAIN

COvER

SCREw

CHAIN

COvER

CHAIN

CHAIN TENSION

PIN HOLE

SPROCKET

La page est en cours de chargement...

Ryobi P545 Manuel utilisateur

Ce manuel convient également à

Ryobi P545 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents