Unbranded R6GP 6, 7.5 - 10 Ton Archived 2/23/12 Manuel utilisateur

Marque: Unbranded

Modèle: R6GP 6, 7.5 - 10 Ton Archived 2/23/12

Taper: Manuel utilisateur

Ce manuel convient également à

IMPORTANT! Please read all information in this manual thoroughly and become familiar with the capabilities and

use of your appliance before attempting to operate or maintain this unit. Pay attention to all safety warnings and

any other special notes highlighted in the manual. Safety markings are used frequently throughout this manual to

designate a degree or level of seriousness and should not be ignored. WARNING indicates a potentially hazardous

situation that if not avoided, could result in personal injury or death. CAUTION indicates a potentially hazardous

situation that if not avoided, may result in minor or moderate injury or property damage. Keep this literature where

you have easy access to it in the future. If a problem occurs, check the instructions and follow recommendations

given. If these suggestions don’t eliminate your problem, call your servicing contractor.

Do not attempt to service this unit yourself! Under no circumstances should the appliance owner attempt to install

and/or service this equipment. Some local codes require licensed installation / service personnel for this type of

equipment. Improper service, adjustment, or maintenance may cause explosion, ﬁre, electrical shock or other

hazardous conditions which may result in personal injury or property damage.

USER’S MANUAL

R6GP-090 ShownR6GN-150 Shown

Single Package Gas Heating / Electric Cooling Rooftop Unit

R6GP-072 (6 Ton), -090 (7.5 Ton), & -120 (10 Ton) Series

R6GN-150 (12.5 Ton) & -180 (15 Ton) Series

DO NOT DESTROY. PLEASE READ CAREFULLY AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

WHAT TO DO IF YOU SMELL GAS

• Donottrytolightanyappliance.

• Do not touch any electrical switch; do not

useanyphoneinyourbuilding.

• Leavethebuildingimmediately.

• Immediately call your gas supplier from a

neighborsphone.Followthegassuppliers

instructions.

• Ifyoucannotreachyourgassupplier,call

theredepartment.

FIRE OR EXPLOSION HAZARD

•Failure to follow safety warnings exactly

could result in serious injury or property

damage.

•Installation and service must be performed

byaqualiedinstaller,serviceagencyorthe

gassupplier.

• Do not store or use gasoline or other

ammablevaporsandliquidsinthevicinity

ofthisoranyotherappliance.

WARNING:

AbOUT THE ROOFTOP UNIT

This gas heating / electric cooling unit has been

designed and built to provide many years of safe and

dependable comfort, providing it is properly installed

and maintained. With regular maintenance, this unit will

operate satisfactorily year after year. Abuse, improper

use, and/or improper maintenance can shorten the life

of the appliance and create unsafe hazards. A regular

service and maintenance schedule should be established

to ensure efﬁcient and safe operation of the unit. See

System Maintenance on pages 3 - 4.

IMPORTANT SAFETY INFORMATION

WARNING:

To avoid possible equipment damage, re,

or death, the following instructions must be

observedregardingunitlocation,combustion

airrequirements,andoperationalprocedures.

• To achieve optimum performance and minimize

equipment failure, it is recommended that periodic

maintenance be performed on this unit. The ability

to properly perform maintenance on this equipment

requires certain mechanical skills and tools. Please

consult your dealer for maintenance information and

availability of maintenance contracts.

• Theareaaroundthegasheating/electriccoolingunit

and the vicinity of any other gas appliances must be

kept clear and free of combustible materials, gasoline,

and other ﬂammable vapors and liquids. Do not store

or use ﬂammable items such as paint, varnish, or

strippers in the vicinity of the unit.

• Donotusetheareaaroundtheunitasastoragearea.

This area must be kept clean and clear of loose or

exposed insulation materials. Examine the unit’s area

when it is installed or when insulation is added, since

some insulation materials may be combustible.

• Donotusethisapplianceifanyparthasbeenunder

water. Immediately call a qualiﬁed service technician

to inspect the unit and to replace any part of the

control system and any gas control which has been

under water.

• Familiarizeyourselfwiththecontrolsthatshutoffthe

gas and electrical power to the unit. If the unit is to be

shut down for an extended period of time, turn off both

thegasandelectricalpower.Foryoursafetyalways

turn off both the gas and electrical power before

performing service or maintenance on the furnace. If

the gas supply must be shut off, refer to the gas valve

label(Figures3or4,pages5-6).

CombustionAirSupply

WARNING:

Combustion air must not be drawn from a

corrosiveatmosphere.

The gas heating/electric cooling unit needs an adequate

supply of combustion and ventilation air for proper and safe

operation. Do not block or obstruct air openings on the unit

or air openings supplying the area where it is installed.

If the unit is operated with inadequate combustion air

supply, the ﬂame roll-out control switch located above

the burners will open, turning off the gas supply to the

burners. The ﬂame roll-out control is a manual reset

device. Do not attempt to reset this device yourself! Call

your servicing contractor.

To maximize heat exchanger life, the combustion air

must be free of chemicals which form corrosive acidic

compounds in the combustion gases.

IMPORTANT NOTE: Do not store any chemicals with

ﬂammable or caustic vapors near the vent termination.

Some examples of these chemicals are:

Ductwork

WARNING:

Failure to prevent products of combustion

frombeingcirculatedintotheoccupiedspace

can create potentially hazardous conditions

including carbon monoxide poisoning that

couldresultinpersonalinjuryordeath.

The duct connections must be physically sound and sealed

to the unit’s casing to prevent products of combustion from

entering the occupied space.

The return air and circulating air ductwork must not be

connected to any other heat producing device such as

a ﬁreplace insert, stove, etc. Doing so may result in ﬁre,

explosion, personal injury, carbon monoxide poisoning,

or property damage.

OPERATING INSTRUCTIONS

Thermostat styles vary. Some models may not include

the AUTO mode and others will have the AUTO in place

of the HEAT and COOL. Others may include all three.

Please refer to the thermostat’s User Manual for detailed

programming instructions.

Thethermostatshouldbemountedabout5feetabovethe

ﬂoor on an inside wall and not on an outside wall or other

location where its operation may be adversely affected by

radiant heat from ﬁreplaces, sunlight, or lighting ﬁxtures,

and convective heat from warm air registers or electrical

appliances.

Cooling Operation (1 or 2-Stage Operation)

1. Set the thermostat system mode to COOL and the

thermostatfanmodetoAUTO.SeeFigure1.

2. Set the thermostat temperature selector to the desired

temperature level. The outdoor fan, compressor, and

indoor blower will all cycle on and off to maintain the

indoor temperature at the desired cooling level. On 2

stage cooling models, the second stage compressor

will cycle as required.

NOTE: If the temperature level is re-adjusted, or the

system mode is reset, the fan and compressor in the

outdoor unit may not start immediately. A protective

timer circuit holds the compressor and the outdoor fan

offforapproximately5minutesfollowingaprevious

operation or the interruption of the main electrical

power.

Heating Operation (2 Stage)

1. Set the thermostat system mode to Heat and the

thermostatfanmodetoAUTO.SeeFigure1.

2. Set the thermostat temperature selector to the

desired temperature level. The indoor blower and

gas heat module will cycle on and off to maintain

the indoor temperature at the desired heating level.

NOTE: On some units there is a factory set 3 minute

time delay between Stage 1 and Stage 2 heat when

Stage 2 heating is required. See Unit wiring diagram

label.

WARNING:

Ifoverheatingoccurs,orthegassupplyfailsto

shutoff,shutoffthegasvalvetotheunitbefore

shuttingofftheelectricalsupply.

NOTE: This unit is equipped with a manual-reset ﬂame

roll-out limit switch. This switch acts to verify that the

burner ﬂame is being drawn into the heat exchanger

tubes. If the ﬂame is not being drawn into the tubes, the

ﬂame roll-out switch will open within several seconds.

When this switch opens, the gas valve will de-energize

to stop the ﬂow of gas. The combustion inducer will stay

energized and continue to operate until the thermostat

is satisﬁed or the switch is closed. Do not reset the ﬂame

roll-out switch before identifying and correcting the fault

condition that caused the switch to open. If the switch

will not reset or continues to open, immediately contact

a qualiﬁed serviceman to identify and repair the problem.

SystemShutdown

SetthethermostatsystemmodetoOFFandthethermostat

fanmodetoAUTO.SeeFigure1.NOTE: The system will

not operate, regardless of the thermostat temperature

selector’s setting.

OperatingtheIndoorBlowerContinuously

Set the thermostat fan mode to ON (or CONT on some

thermostatmodels).SeeFigure1.

The indoor blower will start immediately, and will run

continually until the fan switch is reset to AUTO.

The continuous indoor blower operation can be obtained

with the thermostat system switch set in any position,

including OFF. NOTE: The continuous indoor blower

operation is typically used to circulate the indoor air to

equalize a temperature imbalance due to solar loads,

increased occupancy loads, or mechanical equipment

operation.

SYSTEM MAINTENANCE

CAUTION:

Verify all electrical power to the unit is

disconnected and the gas is shut off before

performing the following recommended

maintenance.

CAUTION:

DO NOT touch any of the internal electrical

componentswhilecleaningtheunit.

Proper maintenance is most important to achieve the best

performance from the appliance and should be performed

by a qualiﬁed service technician at least once a year.

Followthemaintenance schedule andthe instructions

below for years of safe, trouble free operation.

• Donotplacecombustiblematerialsonoragainstthe

cabinet.

• Donotstoregasolineoranyotherammablevapors

and liquids in the vicinity of the unit.

• Annually inspect the physical support of the unit to

ensure that it is physically sound without sagging,

cracks, gaps, etc., around the base so as to provide a

seal between the support and the base.

Figure1.DigitalThermostat

Fan

Mode

Temperature

Selector

System

Mode

• Annuallyinspect the return-airconnection to ensure

that it is physically sound and is still sealed to the

casing of the unit. Also inspect the unit, ductwork, and

vent system for signs of physical deterioration.

• Alwaysreplacethedoorsontheunitafterservicing.

Do not operate the unit without all doors and covers

in place. Avoid operating the unit when windows and

doors are open.

RegularCleaning

• Remove any leaves and grass clippings from the

outdoor coil. IMPORTANT:Becarefulnottodamage

thealuminumns.

• Checkforandremoveanyobstructionssuchastwigs,

sticks, etc.

• Clean the blower compartment regularly during the

heating and cooling seasons to remove any dust

that may have accumulated in the compartment or on

the blower and motor. Buildup of dust on the blower

and motor can create excessive loads on the motor

resulting in higher than normal operating temperatures

and possible shortened service life.

Air Filters

WARNING:

Never operate the unit without a lter in the

returnair system.Dust and lint in thereturn

aircan buildup ontheinternalcomponents,

resulting in loss of efficiency, equipment

damage,andpossiblererisk.

R6GP&R6GNSeries

units are factory equipped with

pleated 2 inch disposable ﬁlters. The ﬁlters should be

checked periodically and replaced (or cleaned) when

necessary with ﬁlters of the same dimensional size.

Replaceusingdisposablelterswithaminimumairow

ratingof500FPMorpermanentltersonly.

IMPORTANT NOTES:

• The lter rack in 6, 7.5 & 10 ton units are eld

adjustable to accommodate 1” permanent lters.

DO NOTuse1”disposableltersintheseunits.

• Always replace the lter access panels after

changingorcleaningthelters.DONOToperate

unitwithoutthelteraccesspanelsinplace.

• Itisveryimportanttoreplaceorcleanthelter(s)

installed in the return air duct of this system. A

cloggedltercouldcauseairowrelatedproblems

and reduce the overall efciency of your unit.

Always replace disposable lter(s) installed in

yoursystemonlywiththesamesizedimensional

ltersthatarebeingreplaced.

• Filters must be ULC approved or equivalent for

useinCanada.

MotorLubrication

The motors for the circulating air blower, outdoor fan, and

combustion blower are pre-lubricated and sealed by the

manufacturer. No further oiling is required for the life of

this product.

BurnerMaintenance

CAUTION:

Somecomponentsintheburnervestibuleare

at high temperatures while the burners are

operating.Usecautiontoavoidpersonalinjury.

Check the burner ﬂames at the start of every heating

season. Set the thermostat above the room temperature.

Removethecontrolaccesspaneltotheunitandvisually

inspect the burner assembly to make sure that the ﬂame

is drawn directly into the center of the heat exchanger tube

(SeeFigure2).Inaproperlyadjustedburnerassembly,

the ﬂame bends up and to the left at the end of the heat

exchanger tube, and the end of the ﬂame will be out of

sight around the bend. The ﬂame color should be blue,

however some light yellow streaks may occur on the outer

portions of the ﬂame.

TROUbLESHOOTING

Before you call a Technician, check the following:

• Checkthethermostatsetting.Makesurethesystem

mode and temperature settings are correct.

• Checktheelectricalpanelfortrippedcircuitbreakers.

• Checktheltersfordustaccumulation.

• Check the unit and make sure it is clean and not

covered with grass or leaves.

• Iftheitemsabovedon’tresolveyourproblems,then

call your nearest service technician.

Figure2.BurnerInspection

A. This appliance does not have a pilot. It is equipped with

an ignition device which automatically lights the burner.

Do not try to light the burner by hand.

B.BEFOREOPERATINGsmellallaroundtheappliance

area for gas. Be sure to smell next to the ﬂoor because

some gas is heavier than air and will settle on the ﬂoor.

WHATTODOIFYOUSMELLGAS

• Donottrytolightanyappliance.

• Donottouchanyelectricalswitch;donotuseanyphone

in your building.

• Immediatelycallyourgassupplierfromaneighbor’s

phone.Followthegassupplier’sinstructions.

• Ifyoucannotreachyourgassupplier,callthere

department.

C. Use only your hand to push in or turn the gas control

knob. Never use tools. If the knob will not push in or move

by hand, do not try to repair it, call a qualiﬁed service

technician.Forceorattemptedrepairmayresultinare

or explosion.

D. Do not use this appliance if any part has been under

water. Immediately call a qualiﬁed service technician

to inspect the appliance and to replace any part of the

control system and any gas control which has been

under water.

1. ATTENTION! Lire d’abord la liste des mesures de

sécurité ci-dessus.

2. Mettre le thermostat à la position minimale.

3. Couper le courant électrique qui mène à l’appareil.

4. Cet appareil ménager étant doté d’un système

d’allumage automatique, ne pas essayer d’allumer le

brûleur manuellement.

 5.Retirerlepanneau/voletd’accèsdecommande(panneau

supérieurs’ils’agitd’unmodèleàdeuxpanneaux).

 6.Fairetournerlerobinetàgazdanslesensdesaiguilles

d’une montre

pourl’amenersurlapositionOFF

(Arrêt)(VoirFigure1).

 7.Attendrecinq(5)minutespours’assurerdela

dissipation du gaz.

 Encasd’odeur,ARRÊTERLEPROCÉDÉ.Suivreles

instructionsci-dessus(SectionB).Enl’absencede

toute odeur de gaz, avancer à l’étape suivante.

 8.Fairetournerlerobinetàgazdanslesensinversedes

aiguilles d’une montre

pour l’amener sur la position

ON(Marche)(VoirFigure1).

 9.Remettrelepanneau/voletd’accèsdecommandeen

place (panneau supérieur s’il s’agit d’un modèle à deux

panneaux).

10.Rebrancherl’appareilsurleréseauélectrique.

11. Ajuster le thermostat à la position désirée.

12. Si l’appareil ne fonctionne pas, suivre les “Directives

d’arrêt” cidessous et appeler le technicien de service.

A. Cet appareil ménager n’a pas de veilleuse. II est doté

d’un système d’allumage automatique. Ne pas essayer

d’allumer le brûleur manuellement.

B.AVANTL’USAGE.Attentionàunepossibleodeurde

gaz surtout au niveau du plancher où les gaz les plus

lourds ont la tendance de se concentrer.

ENCASD’ODEURDEGAZ.

• Nemettreenmarcheaucunappareilélectrique.

• Netoucheràaucuncommutateurélectrique,nepas

employer le téléphone.

• Quitterlebâtimentimmédiatementetavertirla

compagnie du gaz en utili sant le téléphone d’un voisin.

• Adéfautdelacompagniedugaz,avertirleservicedes

pompiers.

C. Enfoncer ou faire tourner le robinet à gaz à la main

seulement. Ne jamais utiliser d’outils. S’il n’est pas

possible de faire tourner ou d’enfoncer le robinet à la

main,nepasessayerdeleréparer.Faireappelàun

spécialiste.Forceroutenterderéparerlerobinetpourrait

être à l’origine d’une explosion ou d’un incendie.

D. II est déconseillé d’utiliser cet appareil en contact

prolongéavecl’eau.Faireinspecterouremplacer

toute commande par un technicien qualiﬁé si un des

systèmes de contrôle du gaz s’est trouvé sous l’eau.

1. STOP!Readthesafetyinformationaboveonthis

label.

2. Set the thermostat to the lowest setting.

3. Turn off all electrical power to the appliance.

4. The appliance’s ignition device automatically lights

the burner. Do not try to light burner by hand.

 5.Removethecontrolaccessdoor/panel(upperdoorif

two-doormodel).

 6.Movethegascontrolknobclockwise

to“OFF”.

(SeeFigure1)

 7.Waitve(5)minutestoclearoutanygas.Thensmell

for gas, including near the ﬂoor. If you smell gas,

STOP!Follow“B”inaboveinformation.Ifyoudon’t

smell gas, go to the next

step.

8. Move the gas control knob

counterclockwise

“ON”.(SeeFigure1)

 9.Replacethecontrol

access door/panel (upper

dooriftwo-doormodel).

10.Turnonallelectrical

power to the appliance.

11. Turn the thermostat to a desired setting.

12. If the appliance will not operate, follow the

instructions“ToTurnOffGasToAppliance”andcall

your service technician or gas supplier.

7106750(Replaces710329A)(03/07)

1. Mettre le thermostat à la position minimale.

2. Débrancher l’appareil en prévision de la réparation.

 3.Retirerlepanneau/voletd’accèsdecommande(panneau

supérieurs’ils’agitd’unmodèleàdeuxpanneaux).

 4.Fairetournerlerobinetàgazdanslesensdes

aiguilles d’une montre

pour l’amener sur la

positionOFF(Arrêt)Nepasforcer(VoirFigure1).

 5.Remettrelepanneau/voletd’accèsdecommandeen

place (panneau supérieur s’il s’agit d’un modèle à deux

panneaux).

POUR VOTRE SÉCURITÉ.

À LIRE AVANT L’EMPLOI

FOR YOUR SAFETY READ

bEFORE OPERATING

1. Set the thermostat to the lowest setting.

2. Turn off all electrical power to the appliance if service is

to be performed.

 3.Removethecontrolaccessdoor/panel(upperdoorif

two-doormodel).

4. Move the gas control knob clockwise

to“OFF”.Do

notuseforce.(SeeFigure1)

 5.Replacethecontrolaccessdoor/panel(upperdoorif

two-doormodel).

ATTENTION!L’inobservationdecesinstructions

peutentraînerunincendieouuneexplosionpouvant

causerdesdammagesàvotrepropriétéàvotre

personne,oulamort.

WARNING:Ifyoudonotfollowtheseinstructions

exactly,areorexplosionmayresultcausingproperty

damage,personalinjury,orlossoflife.

TO TURN OFF

GAS TO APPLIANCE

DIRECTIVES D’ARRÊT

KNOB

( R O B I N E T ) 

Figure1

MODE D’EMPLOI

OPERATING INSTRUCTIONS

¢7106757¤

Figure3.GasValveLabelfor6TonUnits

A. This appliance does not have a pilot. It is equipped with

an ignition device which automatically lights the burner.

Do not try to light the burner by hand.

B. BEFORE OPERATING smell all around the appliance

area for gas. Be sure to smell next to the ﬂ oor because

some gas is heavier than air and will settle on the ﬂ oor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone

in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁ re

department.

C. Use only your hand to push in or turn the gas control

knob. Never use tools. If the knob will not push in or move

by hand, do not try to repair it, call a qualiﬁ ed service

technician. Force or attempted repair may result in a ﬁ re

or explosion.

D. Do not use this appliance if any part has been under

water. Immediately call a qualiﬁ ed service technician

to inspect the appliance and to replace any part of the

control system and any gas control which has been

under water.

1. ATTENTION! Lire d’abord la liste des mesures de

sécurité ci-dessus.

2. Mettre le thermostat à la position minimale.

3. Couper le courant électrique qui mène à l’appareil.

4. Cet appareil ménager étant doté d’un système

d’allumage automatique, ne pas essayer d’allumer le

brûleur manuellement.

5. Retirer le panneau/volet d’accès de commande

(panneau supérieur s’il s’agit d’un modèle à deux

panneaux).

6. Réglez l’interrupteur de commande du gaz à la position

“OFF”. (voir Figure 1).

7. Attendre cinq (5) minutes pour s’assurer de la

dissipation du gaz.

En cas d’odeur, ARRÊTER LE PROCÉDÉ. Suivre les

instructions ci-dessus (Section B). En l’absence de

toute odeur de gaz, avancer à l’étape suivante.

8. Réglez l’interrupteur de commande du gaz à la position

“ON”. (voir Figure 1).

9. Remettre le panneau/volet d’accès de commande en

place (panneau supérieur s’il s’agit d’un modèle à deux

panneaux).

10. Rebrancher l’appareil sur le réseau électrique.

11. Ajuster le thermostat à la position désirée.

12. Si l’appareil ne fonctionne pas, suivre les “Directives

d’arrêt” cidessous et appeler le technicien de service.

A. Cet appareil ménager n’a pas de veilleuse. II est doté

d’un système d’allumage automatique. Ne pas essayer

d’allumer le brûleur manuellement.

B. AVANT L’USAGE. Attention à une possible odeur de

gaz surtout au niveau du plancher où les gaz les plus

lourds ont la tendance de se concentrer.

EN CAS D’ODEUR DE GAZ.

• Ne mettre en marche aucun appareil électrique.

• Ne toucher à aucun commutateur électrique, ne pas

employer le téléphone.

• Quitter le bâtiment immédiatement et avertir la

compagnie du gaz en utili sant le téléphone d’un voisin.

• A défaut de la compagnie du gaz, avertir le service des

pompiers.

C. Enfoncer ou faire tourner le robinet à gaz à la main

seulement. Ne jamais utiliser d’outils. S’il n’est pas

possible de faire tourner ou d’enfoncer le robinet à la

main, ne pas essayer de le réparer. Faire appel à un

spécialiste. Forcer ou tenter de réparer le robinet pourrait

être à l’origine d’une explosion ou d’un incendie.

D. II est déconseillé d’utiliser cet appareil en contact

prolongé avec l’eau. Faire inspecter ou remplacer

toute commande par un technicien qualiﬁ é si un des

systèmes de contrôle du gaz s’est trouvé sous l’eau.

1. STOP! Read the safety information above on this label.

2. Set the thermostat to the lowest setting.

3. Turn off all electrical power to the appliance.

4. The appliance’s ignition de

vice automatically lights the

burner. Do not try to light burner by hand.

5. Remove the control access door/panel (upper door if

two-door model).

6. Move the gas control switch to the “OFF” position. (See

Figure 1)

7. Wait ﬁ ve (5) minutes to clear out any gas. Then

smell for gas, including near the ﬂ oor. If you

smell gas, STOP! Follow “B” in

above information. If you

don’t smell gas, go to

the next step.

8. Move the gas control

switch to the “ON”

position. (See Figure 1)

9. Replace the control

access door/panel

(upper door if two-door

model).

10. Turn on all electrical power to the appliance.

11. Turn the thermostat to a desired setting.

12. If the appliance will not operate, follow the instructions

“To Turn Off Gas To Appliance” and call your service

technician or gas supplier.

710674-0 (Replaces 7104030) (03/07)

1. Mettre le thermostat à la position minimale.

2. Débrancher l’appareil en prévision de la réparation.

3. Retirer le panneau/volet d’accès de commande

(panneau supérieur s’il s’agit d’un modèle à deux

panneaux).

4. Réglez l’interrupteur de commande du gaz à la position

“OFF”. Ne forcez pas. (voir Figure 1).

5. Remettre le panneau/volet d’accès de commande en

place (panneau supérieur s’il s’agit d’un modèle à deux

panneaux).

POUR VOTRE SÉCURITÉ.

À LIRE AVANT L’EMPLOI

FOR YOUR SAFETY READ

BEFORE OPERATING

1. Set the thermostat to the lowest setting.

2. Turn off all electrical power to the appliance if service is

to be performed.

3. Remove the control access door/panel (upper door if

two-door model).

4. Move the gas control switch to the “OFF” position. Do

not use force. (See Figure 1)

5. Replace the control access door/panel (upper door if

two-door model).

ATTENTION!

L’inobservation de ces instructions

peut entraîner un incendie ou une explosion pouvant

causer des dam mages à votre propriété à votre

personne, ou la mort.

WARNING: If you do not follow these instructions

exactly, a ﬁ re or explosion may result causing property

damage, personal injury, or loss of life.

TO TURN OFF

GAS TO APPLIANCE

DIRECTIVES D’ARRÊT

MODE D’EMPLOI

OPERATING INSTRUCTIONS

SWITCH

(INTERRUPTEUR)

Figure 1

Figure4.GasValveLabelfor7.5,10,12.5,&15TonUnits

708957A(Replaces7089570&708882A)

WARRANTY INFORMATION

A warranty certiﬁcate with full details is included with the equipment. Carefully review these responsibilities with your

dealer or service company. The manufacturer will not be responsible for any costs found necessary to correct problems

due to improper setup, improper installation, adjustments, improper operating procedure on the part of the user, etc.

Some speciﬁc examples of service calls which are not included in the limited warranty are:

• Correctingwiringproblemsintheelectricalcircuitsupplyingtheequipment.

• Resettingcircuitbreakersorotherswitches.

• Adjustingorcalibratingofthermostat.

Specications&illustrationssubjecttochangewithoutnoticeorincurringobligations(05/15).

Unbranded R6GP 6, 7.5 - 10 Ton Archived 2/23/12 Manuel utilisateur

Marque: Unbranded

Modèle: R6GP 6, 7.5 - 10 Ton Archived 2/23/12

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Unbranded R6GP 6, 7.5 - 10 Ton Archived 2/23/12 User manual

Unbranded R6GP 6, 7.5 - 10 Ton Archived 2/23/12 Manuel utilisateur

Ce manuel convient également à

Unbranded R6GP 6, 7.5 - 10 Ton Archived 2/23/12 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents