Unika PA-500 Le manuel du propriétaire

Marque: Unika

Modèle: PA-500

Catégorie: Amplificateurs audio

Taper: Le manuel du propriétaire

User Instructions

This booklet contains important information concerning the proper and safe operation of your new amplifier.

PA-Series

PA-500

Made in Taiwan

Professional Power Amplif iers

Index

02 Important Precautions

Introduction02

03 Front Panel

04 Rear Panel

05 Set Up

07 Operating Modes

08 Protection

08 Features

09 Specifications

UNiKA

Active

Clip

Signal

Active

Clip

Signal

UNiK A

PA 500

PROFESSIONAL AMPLIFIER

UNiKA PA-500

page 1

This symbol is intended to alert the user to the presence of

non insulated "dangerous voltage" within the product's

enclosure that may be of sufficient magnitude to constitute

a risk of electric shock to persons.

CAUTION: Risk of the electrical shock - DO NOT OPEN!

CAUTION: To reduce the risk of electrical shock, do not remove cover. No user serviceable parts inside. Refer all servicing

to qualified service personnel.

WARNING: To prevent electrical shock or fire hazard, do not expose this amplifier to rain or moisture. Before using this

amplifier read the user manual for further warnings.

This symbol is intended to alert the user of

the presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the product.

Este símbolo tiene el propósito de alertar al usuario de la

presencia de “voltaje peligroso” que no tiene aislamiento

dentro de la caja del producto que puede tener una

magnitud sufciente como para constituir riesgo de corrientazo.

PRECAUCIÓN: Riesgo del choque eléctrico - NO SE ABRA

PRECAUCIÓN: Para disminuir el riesgo de choque eléctrico, no quite la cubierta. No hay piezas adentro que el usario puede

reparar. Deje todo mantenimiento al los técnicos cualifcados.

ADVERTENCIA: Para prevenir choque eléctrico o riesgo de incendios, no deja expuesto a la lluvia o a la humedad este amplif

cador. Antes de usar este amplif cador, lea mas advertencias en la guia de operacion.

Este símbolo tiene el propósito de alertar al

usuario de la presencia de instrucciones

importantes sobre la operación y

mantenimiento en la literatura que vienc con el producto.

Ce symbole est utilisé pur indiquer à l’utilisateur la présence

à l'intérieur de ce produit de tension non-isolée

dangereuse pouvant être d'intensité suffisante pour

constituer un risque de choc électrique.

ATTENTION: Risque de choc électrique - NE PAS OUVRIR!

ATTENTION: Afin de réduire le risque de choc électrique, ne pas enlever le couvercle. Il ne se trouve à l’intérieur aucune piéce

pouvant être réparée par l'utilisateur. Confier l'entretien à un personnel qualifé.

AVERTISSEMENT: Afin de prévenir les risque de décharge ou de feu, n’exposez pas cet appareil à la pluie ou à l’humidité.

Avant d’utiliser cet amplificateur, lisez les avertissements supplémentaries situés dans le guide.

Ce symbole est utilisé pour indiquer à l’utilisateur

qu'il trouvera d'importantes instructions

importantes sur l'utilisation et l'entretien de

l'appareil dans la littérature accompagnant le produit.

Dieses Symobl soll den Anwender vor unisollierten

gefährlichen Spannungen innerhalb des Gehäuses warnen,

die von Ausreichender Stärke sind, um einen elektrischen

Schlag verursachen zu können.

VORSICHT: Risiko - Elektrischer Schlag! Nicht öffnen!

VORSICHT: Um ddas Risiko eines elektrischen Schlages zu vermeiden, nicht die Abdeckung enfernen. Es befinden sich keine

Teile darin, die vom Anwender repariert werden könnten. Reparaturen nur von qualifzierte Fachpersonal

durchführen lassen.

ACHTUNG: Um einen elektrischen Schlag oder Feuergefahr zu vermeiden, sollte diesen Gerät nicht dem Regen oder

Feuchtigkeit ausgesetz werden. Vor Inbetriebnahme unbedingt die Bedienungsanleitung lesen.

Dieses Symobl soll den Benutzer auf wichtige

Instruktionen in der Bedienungsanleitung

aufmerksam machen, die Handhabung und

Wartung des Produkts betreffen.

CAUTION

Do not open -

risk of electric shock

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE THE COVER. THERE ARE NO USER

SERVICEABLE PARTS INSIDE. REFER ALL SERVICE TO

YOUR AUTHORIZED DEALER.

The lightning flash with an arrow triangular

symbol is intended to alert the user to the

presence of non insulated “dangerous

voltage” within the products enclosure, and

may be of sufficient magnitude to constitute

a risk of electric shock.

The exclamation point triangular symbol is

intended to alert the user to the presence of

important operating and maintenance

(servicing) instructions in the user manual

accompanying the amplifier.

FOR OPTIMUM PERFORMANCE AND RELIABILITY

DO NOT PRESENT THE AMPLIFIER WITH A

SPEAKER LOAD OF LESS THAN 2 OHMS OR ANY

COMBINATION OF SPEAKERS THAT TOGETHER ARE LESS

THAN 2 OHMS!

USING ONE SPEAKER, IT MUST BE RATED AT 4 OR MORE

OHMS. USING TWO SPEAKERS, THEY MUST RATED EACH AT 4

OR MORE OHMS.

USING THREE SPEAKERS, THEY MUST BE RATED EACH AT 8

OR MORE OHMS.

POUR ASSURER LA FIABILETE ET OBTENIT UNE

PERFORMANCE OPTIMALE, NESOUMETTE

JAMAIS L’AMPLIFICATEUR A UNE CHARGE

D’IMPEDANCE

TOTALE INFERIEURE A 2 OHMS, NI AVEC UN H.P. N EN

COMBINAISON DES H.P.

AVEC UN H.P., IL FAUT UNE CHARGE D’IMPEDANCE MINIMUM

DE 2 OHMS.

AVEC DEUX H.P., FAUT POUR CHAOUN UNE CHARGE

D’IMPEDANCE MINIMUM DE 4 OHMS.

AVEC TROIS H.P., FAUT POUR CHAOUN UNE CHURGE

D’IMPEDANCE MINIMUM DE 8 OHMS.

page 2

IMPORTANT PRECAUTIONS

 To reduce the risk of electrical shock or fire, do not expose this unit rain or

moisture.

 Do not spill water or other liquids into or on to your unit.

 Do not attempt to operate this unit if the power cord has been frayed or

broken.

 Do not attempt to remove or break off the ground prong from the electrical

cord. This prong is used to reduce the risk of electrical shock and f re in

case of an internal short.

 Disconnect main power before making any type of connection.

 Do not remove the cover under any conditions. There are no user

serviceable parts inside.

 Never plug this unit in to a dimmer pack.

 Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

 Do not attempt to operate this unit, if it becomes damaged.

 This unit is intended for indoor use only, use of this product outdoors voids

all warranties.

 During long periods of non-use, disconnect the unit’s main power.

 Always mount this unit in a safe and stable manner.

 Power cords should be routed so they are not likely to be walked on,

pinched by items placed upon or against them.

 Cleaning -The outside of the unit should be wipe down with a soft cloth and

mild cleaner when needed.

 Heat -The amplifier should be situated away from heat sources such as

radiators, heat registers, stoves, or other appliances (including amplifiers)

that produce heat.

 The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the unit.

C. The appliance has been exposed to rain or water.

D. The fixture does not appear to operate normally or exhibits a

marked change in performance.

Congratulations and thank you for purchasing PA-500 amplifier. This

amplifier is representation of UNiKA’s continuing commitment to produce

the best and highest quality audio products at an affordable price. This

amplifier is designed to provide a big impact in sound reproduction. Please

read and understand this manual completely before attempting to operate

your new amplifier. This booklet contains important information concerning

the proper and safe operation of your new amplifier.

UNPACKING: Every PA-500 amplifier has been thoroughly tested and

has been shipped in perfect operating condition. Carefully check the

shipping carton for damage that may have occurred during shipping. If the

carton appears to be damaged, carefully inspect your unit for any damage

and be sure all accessories necessary to operate the system have arrived

intact. In the event damage has been found or parts are missing, please

contact your dealer for further instructions.

INSTALLATION: This amplifier is designed to mount into a standard

19”rack. The front panel provides four holes used to screw the unit into a

rack. The unit also provides a way to rear mount the unit into a rack for

added security. Rear mounting the unit is especially recommended if the

unit is to mounted into a mobile rack.

INTRODUCTION

Important Precautions Introduction Front Panel Rear Panel Set Up Operating Modes Protection Features Specifications

UNiKA PA-500

PA-500 FRONT PANEL

1. Rack Mounting Ears - Two front panel mounting holes are

provided on each mounting ear.

2. Rack Handle - PA Series amplifiers are designed with rack handle

at two each side. It's not only to make the entire design elegant but

more practical and convenient for users.

3. Cooling Vent - These vents are used for proper cooling. Never

block these vents when installing the amplifier or other associated

equipment and keep them clean at all times. Air must flow

unimpeded through these ports.

4. Active Indicator - When turning on the AC power switch, both two

sides of LED's turn on red for about several seconds while

checking various protection circuits of each channel first. Then,

when entering the normal operating mode, once both channels of

the LED's in blue indicating that the entire power amplifier is ready

for use. This active indicator will light in red when the protection

circuit detects output short circuit or DC leakage. If it turns on red

and does not change to blue, please contact the service center.

5. Clip Indicator - The red clip LED will begin to flash when the

channel begins to overload. At this point the channel will begin to

distort. Under heavy clipping activity, lower the channel's gain

control to reduce the risk of damage to your speakers and

amplifier. This LED may glow when the unit has been turned off,

this is normal.

6. Signal Indicator - This green LED will glow when there is an input

of the audio signal into the channel.

7. Gain Control - This rotary knob is used to control the output signal

of the channel. Tuning the knob in clockwise direction will increase

signal output.

8. AC Power Switch - PA-500 amplifier has a front-panel AC mains

power switch.

page 3

Important Precautions Introduction Rear Panel Set Up Operating Modes Protection Features Specifications Front Panel

UNiKA PA-500

Figure 1

Active

Clip

Signal

Active

Clip

Signal

UNiK A

PA 500

PROFESSIONAL AMPLIFIER

1 3

9. Cooling Vents - These vents are used for proper cooling. Never

block these vents when installing the amplifier or other

associated equipment and keep them clean at all times. Air must

flow unimpeded through these ports.

10. Channel 1-2 Balanced 1/4” TRS & XLR Input Connectors -

These connectors accept input signals on balanced TRS and

XLR input plugs. Connectors for each channel are in parallel, the

unused connectors may be used for “loop through” connection to

other amplifiers.

TRS pin setting: Tip/signal positive, Ring/signal negative,

Sleeve/ground.

XLR pin setting: Pin-2/signal positive, Pin-3/signal negative, Pin-

1/ground.

11. Amp. Mode Selection Switch - This switch allows the amplifier

operating mode from either stereo or mono bridge selection.

Amplifiers are factory-configured for Stereo Mode. See section

on Mode Selection for more information.

12. Fuse Holder - This holder houses the external fuse. Always

replace with the exact same type fuse, otherwise instructed to do

so by an authorized audio service technician.

13. AC Power Input - IEC AC power inlet connector, plug this cable

in to a standard 110V or 220V wall outlet. Be sure that supplied

voltage matches that of the required voltage of your amplifier.

Never plug your amplifier in to a wall outlet that does not match

the required voltage of your amplifier, serious damage may occur

to your unit.

14. Channel 1-2 Output Jack / 5-way Binding Post - Connect to

your speakers input jack. Red is positive signal and Black is

negative signal.

PA-500 REAR PANEL

page 4

Important Precautions Introduction Front Panel Set Up Operating Modes Protection Features Specifications Rear Panel

Figure 2

12 131110 14

UNiKA PA-500

PUSH PUSH

4 Ohms/Ch

Minimum

Stereo Mode

8 Ohms

Minimum

Bridge Mode

100VAC

50-60Hz

875VA

FUSE

T250V

7A L

CAUTION: REPLACE WITH SAME TYPE FUSE AND RATING

ATTENTION: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR

Balanced Balanced

STEREO

AMP MODE

BRIDGE

CH 1 INPUTCH 2 INPUT

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Designed and developed in USA Manufactured in Taiwan

CH 2

BRIDGE

CH 1

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE TO RAIN OR MOISTURE

INPUTS - The PA-500 amplifier allows you to use two types of input connectors per channel, a XLR female jack for balanced connections and

a 1/4” TRS female jack that will accept balanced and unbalanced connectors. Use these connections to connect the output signal from a mixer,

cross-over or EQ to the PA-500 amplifier. A balanced connection is recommended for cable runs longer than 20ft. When constructing your own

XLR cables follow the pin configuration described below for proper connections. For cable runs shorter than 20ft., you may choose the 1/4” TS

unbalanced input option. The 1/4” TS unbalanced input option may be more convenient for most users due to the abundant supply of

prefabricated cables available at your local audio dealer.

BINDING POST/BANANA PLUG: Connect your speakers to the binding post outputs on the rear of the amplifier. The speaker wire may be

connected by bare wire (directly connected, usually for permanent connections), banana plug, or spade connector. Connections are made to

channel one and channel two outputs for Stereo Mode or across the red terminals of channel one and channel two for Mono Bridge Mode.

IMPORTANT NOTICE: Although a speaker will operate with the positive and negative leads plugged into either terminal on the amplifier binding

post, be sure to plug the negative lead into the black terminal and positive lead into the red terminal. Ensuring proper polarity will avoid speakers

being out of phase that can cause a loss of bass response.

2 Hot (+data)

Male XLR Pin Configuration

Figure 3

1 Ground / Return / 0v

3 Negative (-data)

Balanced TRS 1/4” Plug

Hot (+)

Negative (-)

Ground/Shield

Figure 4

Unbalanced TS 1/4” Plug

Hot (+)

Negative (-)

Figure 5

page 5

SET UP

Important Precautions Introduction Front Panel Rear Panel Operating Modes Protection Features Specifications Set Up

OUTPUTS -

UNiKA PA-500

page 6

Important Precautions Introduction Front Panel Rear Panel Operating Modes Protection Features Specifications Set Up

BANANA PLUG: (Figure 6)

When connecting your speakers to the amplifier using banana plugs, be sure that the red and black caps on

the binding post are completely screwed in. Insert the banana plugs into the caps of the binding post, be sure

that the banana plugs are inserted securely to avoid the risk of popping out.

BARE WIRE CONNECTION: (Figure 7)

When connecting your speakers to the amplifier using bare wire, unscrew the red and black caps on the

binding post, be sure not to completely remove or unscrew the red and black caps. Strip back the wire

insulation 1/2” (13mm). Insert the bare wire into the hole that was revealed by unscrewing the binding post

cap. After inserting the wire into the binding post hole, screw the binding post cap down on the wire. To

reduce the risk of shock or damage to your amplifier, be sure that the wire connected to one binding post

does not come in contact with that of another.

SPADE CONNECTOR: (Figure 8)

When connecting your speakers to the amplifier using spade connector, unscrew the red and black caps on

the binding post, be sure not to completely remove or unscrew the red and black caps. Insert the spade

connector into the binding post and tighten the caps down on the spade connector. To reduce the risk of

shock or damage to your amplifier, be sure that the wire connected to one binding post does not come in

contact with that of another.

MONO BRIDGE CONNECTIONS: (Figure 9)

Mono bridge operation connections will follow the above descriptions, however, when operating in mono

bridge operation the speaker connections will run between the two positive (red) leads, Use channel two

positive output terminal for the negative connection and the channel one positive output terminal for the

positive connection.

Typical speaker output using bare wire.

Insert bare wire into the binding post and tighten.

Typical speaker output using spade connectors.

Insert bare wire into the binding post and tighten.

Figure 8

1/5"

13mm

Figure 7

Figure 6

Figure 9

ATTENTION: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CH 2

BRIDGE

CH 1

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE TO RAIN OR MOISTURE

UNiKA PA-500

page 7

Figure 10 Typical Stereo Output Connections

SPEAKERS

2 OHM MINIMUM

SPEAKERS

2 OHM MINIMUM

OPERATING MODES

STEREO OPERATION : Page 7/Figure 10 details an example of a typical stereo set-up. Connect your inputs into channels one and two of the amplifier.

Connect your speakers to the outputs on the rear of the amplifier. Be sure that your front gain controls are turned down to their lowest level (fully counter-

clockwise). Turn your amplifier on. Turn your input source level up. Use your front gain controls to regulate the output volume. Be sure not to raise the volume to

the clip level, however an intermittent clip signal is acceptable.

MONO BRIDGE OPERATION : Page 7/Figure 11 details a mono bridge set-up. Be sure your amplifier and all other audio equipment are powered down.

Press the Stereo/Mono Bridge switch to the Mono Bridge position. Connect an input signal to channel one. Connect your speaker across the red output binding

post on the rear of your amplifier. Turn your equipment on (your amplifier should always be the last item you turn on). Apply an input source signal to your

amplifier. Use the channel one gain control to regulate your amplifier output.

Important Precautions Introduction Front Panel Rear Panel Set Up Protection Features Specifications Operating Modes

PA-500

REAR PANEL

SPEAKERS

4 OHM MINIMUM

PA-500

REAR PANEL

Figure 11 Typical Mono Bridge Set-Up

CH-1 Input

CH-2 Input

STEREO

AMP MODE

BRIDGE

CH-1 Input

Only

STEREO

AMP MODE

BRIDGE

UNiKA PA-500

PUSH PUSH

4 Ohms/Ch

Minimum

Stereo Mode

8 Ohms

Minimum

Bridge Mode

100VAC

50-60Hz

875VA

FUSE

T250V

7A L

CAUTION: REPLACE WITH SAME TYPE FUSE AND RATING

ATTENTION: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR

Balanced Balanced

STEREO

AMP MODE

BRIDGE

CH 1 INPUTCH 2 INPUT

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Designed and developed in USA Manufactured in Taiwan

CH 2

BRIDGE

CH 1

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE TO RAIN OR MOISTURE

PUSH PUSH

4 Ohms/Ch

Minimum

Stereo Mode

8 Ohms

Minimum

Bridge Mode

100VAC

50-60Hz

875VA

FUSE

T250V

7A L

CAUTION: REPLACE WITH SAME TYPE FUSE AND RATING

ATTENTION: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR

Balanced Balanced

STEREO

AMP MODE

BRIDGE

CH 1 INPUTCH 2 INPUT

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Designed and developed in USA Manufactured in Taiwan

CH 2

BRIDGE

CH 1

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE TO RAIN OR MOISTURE

page 8

Important Precautions Introduction Front Panel Rear Panel Set Up Operating Modes Specifications Protection Features

PROTECTION

SAFE POWER LEVELS AT DIFFERENT OUTPUT LOADS:

8-Ohm Loads: The amplifier can operate at its rated power level without risk of overheating. However, it may caused excessive temperature if it is pushed hard enough

to continually light the “CLIP” indicator, the amplifier's average output power can reach its maximum peak.

4-Ohm Loads: If the “CLIP” indicator flashes occasionally, the amplifier is approaching its Maximum long-term power capacity. If it is lit about half the time,

the amplifier channel will probably go into thermal protection within a few minutes.

2-Ohm Loads: Except for an occasional flash, keep the “CLIP” indicator dark to avoid overheating the amplifier channel. Clipping should be kept to a

reasonable minimum. An amplifier's peak current draw at full output power into 2 ohms is several times what the “normal” draw is, but its various protection

circuits will prevent this condition lasting more than a minute or two.

SHORT CIRCUIT PROTECTION - The PA-500 amplifier comes with built-in Output Short Circuit Protects. The Output Short

Circuit Protection protects the output devices of the amplifier from short circuits and stressful loads. If your speaker lines shorted, the

amplifier automatically detects this problem and discontinued operation for that channel. If one side of your amplifier becomes shorted

and goes into protect mode, the other side will continue to operate normally. During short circuit protection, the “ACTIVE” LED will light

indicating amplifier fault. Channel output during the “Short Circuit Protection” will be interrupted (i.e. no sound output). Short Circuit

Protection can usually be traced back to the signal output line (i.e. speaker line). Check the line from the output terminal of the

amplifier to the speaker. If this line is good, check the internal speaker connections and components. A short circuit will usually be

traced to a bad cable or a bad speaker component and is rarely traced to the amplifier itself.

INPUT/OUTPUT PROTECTION - The input circuits are isolated by resistors. An ultrasonic network uncouples RF from the output and helps to keep the amplifier

stable with reactive loads.

OPERATING VOLTAGE (AC MAINS) - On the rear panel will indicate the correct AC mains voltage. Connecting to the wrong voltage is dangerous and may

damage the amplifier. Always be sure the source voltage for your areas matches the required voltage for your amplifier.

GAIN CONTROLS - The gain controls are located on the front panel and are calibrated in 2dB of attenuation from full gain. It is best to adjust the amplifier so no

“hissing” is heard from speakers with no music being played, this will ensure the lowest possible distortion during normal operation.

AMPLIFIER FEATURES

SWITCH-MODE POWER SUPPLY: The PA-500 is designed with SMPS power with CLASS D of Power Stage Topology instead of the traditional toroidal

transformer, therefore the total weight of the amplifier is ultra-light, and also the complete performance is better.

LED INDICATORS: Each channel has three LEDs. One green LED indicates signal, one red LED indicates signal clipping and one red/blue LED indicates

protections mode for shorts/overload.

UNiKA PA-500