Unika MS-3050 Le manuel du propriétaire

Marque: Unika

Modèle: MS-3050

Catégorie: Haut-parleurs de la barre de son

Taper: Le manuel du propriétaire

User Instructions

This booklet contains important information concerning the proper and safe operation of your new amplifier..

MS-Series

MS550 / MS750 / MS1050 / MS2050 / MS3050

Made in Taiwan

Professional Power Amplif iers

Index

0 Introduction2

03 Front Panel

04 Rear Panel

05 Set Up

07 Operating Modes

09 Protection

10 Specifications

UNiKA

SIGNAL SIGNAL

CLIP CLIPPOWER

CH-1 CH-2

POWE R

OFF ON

PROFE SSIO NAL STE REO POW ER AMPL IFIER

MS -7 50

UNiKA

SIGNAL SIGNAL

CLIP CLIPPOWER

CH-1 CH-2

POWE R

OFF ON

PROFE SSIO NAL STE REO POW ER AMPL IFIER

MS -2 05 0

UNiKA

SIGNAL SIGNAL

CLIP CLIPPOWER

CH-1 CH-2

POWE R

OFF ON

PROFE SSIO NAL STE REO POW ER AMPL IFIER

MS -105 0

UNiKA

SIGNAL SIGNAL

CLIP CLIPPOWER

CH-1 CH-2

POWE R

OFF ON

PROFE SSIO NAL STE REO POW ER AMPL IFIER

MS -3 05 0

UNiKA

SIGNAL SIGNAL

CLIP CLIPPOWER

CH-1 CH-2

POWE R

OFF ON

PROFE SSIO NAL STE REO POW ER AMPL IFIER

MS -5 50

UNiKA

IMPORTANT SAFETY INSTRUCTIONS

MS550 / MS750 / MS1050 / MS2050 / MS3050

page 1

This symbol is intended to alert the user to the presence of

non insulated "dangerous voltage" within the product's

enclosure that may be of sufficient magnitude to constitute

a risk of electric shock to persons.

CAUTION: Risk of the electrical shock - DO NOT OPEN!

CAUTION: To reduce the risk of electrical shock, do not remove cover. No user serviceable parts inside. Refer all servicing

to qualified service personnel.

WARNING: To prevent electrical shock or fire hazard, do not expose this amplifier to rain or moisture. Before using this

amplifier read the user manual for further warnings.

This symbol is intended to alert the user of

the presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the product.

Este símbolo tiene el propósito de alertar al usuario de la

presencia de “voltaje peligroso” que no tiene aislamiento

dentro de la caja del producto que puede tener una

magnitud sufciente como para constituir riesgo de corrientazo.

PRECAUCIÓN: Riesgo del choque eléctrico - NO SE ABRA

PRECAUCIÓN: Para disminuir el riesgo de choque eléctrico, no quite la cubierta. No hay piezas adentro que el usario puede

reparar. Deje todo mantenimiento al los técnicos cualifcados.

ADVERTENCIA: Para prevenir choque eléctrico o riesgo de incendios, no deja expuesto a la lluvia o a la humedad este amplif

cador. Antes de usar este amplif cador, lea mas advertencias en la guia de operacion.

Este símbolo tiene el propósito de alertar al

usuario de la presencia de instrucciones

importantes sobre la operación y

mantenimiento en la literatura que vienc con el producto.

Ce symbole est utilisé pur indiquer à l’utilisateur la présence

à l'intérieur de ce produit de tension non-isolée

dangereuse pouvant être d'intensité suffisante pour

constituer un risque de choc électrique.

ATTENTION: Risque de choc électrique - NE PAS OUVRIR!

ATTENTION: Afin de réduire le risque de choc électrique, ne pas enlever le couvercle. Il ne se trouve à l’intérieur aucune piéce

pouvant être réparée par l'utilisateur. Confier l'entretien à un personnel qualifé.

AVERTISSEMENT: Afin de prévenir les risque de décharge ou de feu, n’exposez pas cet appareil à la pluie ou à l’humidité.

Avant d’utiliser cet amplificateur, lisez les avertissements supplémentaries situés dans le guide.

Ce symbole est utilisé pour indiquer à l’utilisateur

qu'il trouvera d'importantes instructions

importantes sur l'utilisation et l'entretien de

l'appareil dans la littérature accompagnant le produit.

Dieses Symobl soll den Anwender vor unisollierten

gefährlichen Spannungen innerhalb des Gehäuses warnen,

die von Ausreichender Stärke sind, um einen elektrischen

Schlag verursachen zu können.

VORSICHT: Risiko - Elektrischer Schlag! Nicht öffnen!

VORSICHT: Um ddas Risiko eines elektrischen Schlages zu vermeiden, nicht die Abdeckung enfernen. Es befinden sich keine

Teile darin, die vom Anwender repariert werden könnten. Reparaturen nur von qualifzierte Fachpersonal

durchführen lassen.

ACHTUNG: Um einen elektrischen Schlag oder Feuergefahr zu vermeiden, sollte diesen Gerät nicht dem Regen oder

Feuchtigkeit ausgesetz werden. Vor Inbetriebnahme unbedingt die Bedienungsanleitung lesen.

Dieses Symobl soll den Benutzer auf wichtige

Instruktionen in der Bedienungsanleitung

aufmerksam machen, die Handhabung und

Wartung des Produkts betreffen.

CAUTION

Do not open -

risk of electric shock

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE THE COVER. THERE ARE NO USER

SERVICEABLE PARTS INSIDE. REFER ALL SERVICE TO

YOUR AUTHORIZED DEALER.

The lightning flash with an arrow triangular

symbol is intended to alert the user to the

presence of non insulated “dangerous

voltage” within the products enclosure, and

may be of sufficient magnitude to constitute

a risk of electric shock.

The exclamation point triangular symbol is

intended to alert the user to the presence of

important operating and maintenance

(servicing) instructions in the user manual

accompanying the amplifier.

FOR OPTIMUM PERFORMANCE AND RELIABILITY

DO NOT PRESENT THE AMPLIFIER WITH A

SPEAKER LOAD OF LESS THAN 2 OHMS OR ANY

COMBINATION OF SPEAKERS THAT TOGETHER ARE LESS

THAN 2 OHMS!

USING ONE SPEAKER, IT MUST BE RATED AT 4 OR MORE

OHMS. USING TWO SPEAKERS, THEY MUST RATED EACH AT 4

OR MORE OHMS.

USING THREE SPEAKERS, THEY MUST BE RATED EACH AT 8

OR MORE OHMS.

POUR ASSURER LA FIABILETE ET OBTENIT UNE

PERFORMANCE OPTIMALE, NESOUMETTE

JAMAIS L’AMPLIFICATEUR A UNE CHARGE

D’IMPEDANCE

TOTALE INFERIEURE A 2 OHMS, NI AVEC UN H.P. N EN

COMBINAISON DES H.P.

AVEC UN H.P., IL FAUT UNE CHARGE D’IMPEDANCE MINIMUM

DE 2 OHMS.

AVEC DEUX H.P., FAUT POUR CHAOUN UNE CHARGE

D’IMPEDANCE MINIMUM DE 4 OHMS.

AVEC TROIS H.P., FAUT POUR CHAOUN UNE CHURGE

D’IMPEDANCE MINIMUM DE 8 OHMS.

page 2

SAFETY PRECAUTIONS

 To reduce the risk of electrical shock or fire, do not expose this unit rain

or moisture.

 Do not spill water or other liquids into or on to your unit.

 Do not attempt to operate this unit if the power cord has been frayed or

broken.

 Do not attempt to remove or break off the ground prong from the

electrical cord. This prong is used to reduce the risk of electrical shock

and f re in case of an internal short.

 Disconnect main power before making any type of connection.

 Do not remove the cover under any conditions. There are no user

serviceable parts inside.

 Never plug this unit in to a dimmer pack.

 Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

 Do not attempt to operate this unit, if it becomes damaged.

 This unit is intended for indoor use only, use of this product outdoors

voids all warranties.

 During long periods of non-use, disconnect the unit’s main power.

 Always mount this unit in a safe and stable manner.

 Power cords should be routed so they are not likely to be walked on,

pinched by items placed upon or against them.

 Cleaning -The outside of the unit should be wipe down with a soft cloth

and mild cleaner when needed.

 Heat -The amplifier should be situated away from heat sources such as

radiators, heat registers, stoves, or other appliances (including

amplifiers) that produce heat.

 The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the unit.

C. The appliance has been exposed to rain or water.

D. The fixture does not appear to operate normally or exhibits a

marked change in performance.

Congratulations and thank you for purchasing MS series amplifier. These

amplifiers are representation of UNiKA’s continuing commitment to produce

the best and highest quality audio products at an affordable price. These

amplifiers are designed to provide a big impact in sound reproduction.

Please read and understand this manual completely before attempting to

operate your new amplifier. This booklet contains important information

concerning the proper and safe operation of your new amplifier.

UNPACKING: Every MS series amplifier has been thoroughly tested

and has been shipped in perfect operating condition. Carefully check the

shipping carton for damage that may have occurred during shipping. If the

carton appears to be damaged, carefully inspect your unit for any damage

and be sure all accessories necessary to operate the system have arrived

intact. In the event damage has been found or parts are missing, please

contact your dealer for further instructions.

INSTALLATION: These amplifiers are designed to mount into a

standard 19”rack. The front panel provides four holes used to screw the unit

into a rack. The unit also provides a way to rear mount the unit into a rack for

added security. Rear mounting the unit is especially recommended if the

unit is to mounted into a mobile rack.

INTRODUCTION

UNiKA

MS550 / MS750 / MS1050 / MS2050 / MS3050

Introduction Front Panel Rear Panel Set Up Operating Modes Protection Specifications

FRONT PANEL

Figure 1

page 3

UNiKA

1. Rack Mounting Ears - Two front panel mounting holes are provided on

each mounting ear.

2. AC Power Switch - This switch is used to control the unit’s mains power.

3. Fan Inlet Grills and Filter - MS Series amplifiers are cooled by one single

rear mounted fan. Cool air from front grills is filtered and flows over the

heatsinks and exhausts to back side. Make sure these outlets remain clear

to allow unrestricted air flow.

4. Channel 1 Gain Control - This rotary knob is used to control the output

signal of channel 1. Turning the knob in clockwise direction will increase

signal output.

5. Channel 2 Gain Control -This rotary knob is used to control the output

signal of channel 2. Turning the knob in clockwise direction will increase

signal output.

6. UNiKA Logo and Model No - MS series has 5 types of 2U models MS-

550 / MS-750 / MS-1050 / MS-2050 / MS-3050.

7. Power Indicator - This blue LED will glow when mains power is applied to the

unit. This light may continue to glow briefly after mains power has been turned

off, this is normal.

8. Channel 1 Clip Indicator - This red LED will begin to flash when the channel

begins to overload (clip), at this point the channel will begin to distort. Under

heavy clipping activity lower the channel’s gain control to reduce the risk of

damage to your speakers and amplifier. This LED may glow when the unit has

been turned off, this is normal.

9. Channel 1 Signal Indicator - This green LED will glow according to the

average signal output.

10. Channel 2 Clip Indicator - This red LED will begin to flash when the channel

begins to overload (clip), at this point the channel will begin to distort. Under

heavy clipping activity lower the channel’s gain control to reduce the risk of

damage to your speakers and amplifier. This LED may glow when the unit has

been turned off, this is normal.

11. Channel 2 Signal Indicator - This green LED will glow according to the

average signal output.

MS550 / MS750 / MS1050 / MS2050 / MS3050

SIGNAL SIGNAL

CLIP CLIPPOWER

CH-1 CH-2

POWER

OFF ON

PROFES SIONAL STEREO POWER AMPLI FIER

MS-550

UNiKA

3 4 5

7 8 9 10

Introduction Rear Panel Set Up Operating Modes Protection SpecificationsFront Panel

page 4

Figure 2

15. Channel 1 Balanced 1/4" TRS & XLR Input Connector - Connect the input

source for channel one to either the balance XLR or the balanced/unbalanced

1/4” input jacks. The 1/4” TRS plug is configured as follows; Tip is positive,

Ring is negative and Sleeve is ground. The XLR jack is configured as follows;

Pin 2 positive, pin 3 negative, pin one ground. See page 5 for more details on

input configuration.

16. Mode Selection Switch - This switch changes the amplifier operating mode

from either stereo or mono bridge. Amplifiers arrive to you preset in the stereo

operation mode.

17. Channel 2 Output Jack / 5-Way Binding Post - Connect to your speaker’s

input jack. Red is positive signal and Black is negative signal.

18. Channel 1 Output Jack / 5-Way Binding Post - Connect to your speaker’s

input jack. Red is positive signal and Black is negative signal.

19. A/C Power Cord - Plug this cable into a standard 110V wall outlet. Be sure

that the supplied voltage in your area matches the amplifier’s required voltage.

Never plug your amplifier into a wall outlet that does not match the required

voltage of your amplifier, serious damage may occur to your unit.

12. Fan Outlet Port - Cooling air enters the amplifier through the front grills and

exhausts through the fan. Be sure not to block these ports when installing the

amplifier or other associated equipment. Air must flow unimpeded through

these ports.

13. Circuit Breaker - This breaker is designed to protect the amplifier and your

speakers in the event of an AC overload. In the event of an electrical overload

the breaker will pop-out. To reset the breaker, push it in. If the breaker

continues to pop, stop using the amplifier and contact customer service.

14. Channel 2 Balanced 1/4" TRS & XLR Input Connectors - Connect the input

source for channel two to either the balance XLR or the balanced/unbalanced

1/4” input jacks. The 1/4” TRS plug is configured as follows; Tip is positive,

Ring is negative and Sleeve is ground. The XLR jack is configured as follows;

Pin 2 positive, pin 3 negative, pin one ground. See page 5 for more details on

input configuration.

REAR PANEL

UNiKA

MS550 / MS750 / MS1050 / MS2050 / MS3050

INPUT

CH 2

STEREO BRIDGE

RESET

~120VAC 60Hz

1000 WATTS

PROFESSIONAL POWER AMPLIFIER

CAUTION

4 OHMS MINIMUM IMPEDANCE PRE CHANNEL

8 OHMS MINIMUM IMPEDANCE IN MONO BRIDGE MODE

P2 P3 P1

SERIAL NO.

INPUT

CH 1

MODE

BRIDGE

MONO

CH 1CH 2

OUTPUT

XS 550

XS 750

XS10 50

XS20 50

XS30 50

12 13

16 1914 15 17 18

Introduction Front Panel Set Up Operating Modes Protection SpecificationsRear Panel

SET UP

INPUTS - The MS series amplifiers allows you to use two types of input connectors per channel, a XLR female jack for balanced connections and

1/4” TRS female jack that will accept balanced and unbalanced connections. Use these connections to connect the output signal from a mixer,

cross-over or EQ to your MS series amplifiers. A balanced connection is recommended for cable runs longer than 20ft. When constructing your own

XLR cables follow the pin configuration described below for proper connections. For cable runs shorter than 20ft., you may choose the 1/4” TS

unbalanced input option. The 1/4” TS unbalanced input option may be more convenient for most users due to the abundant supply of prefabricated

cables available at your local audio dealer. You may use the two XLR “Input Thru” jacks to jump a parallel connection to another amplifier or other

device. For Example: Connect a XLR cable to the input of channel one. You may now connect a XLR cable from the channel one “Input Thru” jack to

the input jack of another amplifier’s channel one input. This will reduce the use of “Y” cables.

OUTPUTS -

BINDING POST/BANANA PLUG: Connect your speakers to the binding post outputs on the rear of the amplifier. The speaker wire may be

connected by bare wire (directly connected, usually for permanent connections), banana plug, or spade connector. Connections are made to

Channels 1 and 2 outputs for Stereo Mode or across the red terminals of Channels 1 and 2 for Mono Bridge Mode.

IMPORTANT NOTICE: Although a speaker will operate with the positive and negative leads plugged into either terminal on the amplifier binding

post, be sure to plug the negative lead into the black terminal and positive lead into the red terminal. Ensuring proper polarity will avoid speakers

being out of phase that can cause a loss of bass response.

Male XLR Pin Configuration

Figure 3

2 Hot (+data)

1 Ground / Return / 0v

3 Cold (-data)

Balanced TRS 1/4” Plug

Hot (+)

Cold (-)

Ground/Shield

Figure 4

Unbalanced TS 1/4” Plug

Hot (+)

Cold (-)

Figure 5

page 5

UNiKA

MS550 / MS750 / MS1050 / MS2050 / MS3050

Introduction Front Panel Rear Panel Operating Modes Protection SpecificationsSet Up

Typical speaker output using spade connectors.

Insert bare wire into the binding post and tighten.

Figure 8

BANANA PLUGS: (Figure 6)

When connecting your speakers to the amplifier using banana plugs, be sure that the red and black caps on the

binding post are completely screwed in. Insert the banana plugs into the caps of the binding post, be sure that

the banana plugs are inserted securely to avoid the risk of popping out.

BARE WIRE CONNECTIONS: (Figure 7)

When connecting your speakers to the amplifier using bare wire, unscrew the red and black caps on the binding

post, be sure not to completely remove or unscrew the red and black caps. Strip back the wire insulation ½”

(13mm). Insert the bare wire into the hole that was reveled by unscrewing the binding post cap. After inserting

the wire into the binding post hole, screw the binding post cap down on the wire. To reduce the risk of shock or

damage to your amplifier, be sure that the wire connected to one binding post does not come in contact with that

of another.

SPADE CONNECTOR: (Figure 8)

When connecting your speakers to the amplifier using spade connector, unscrew the red and black caps on the

binding post, be sure not to completely remove or unscrew the red and black caps. Insert the spade connector in

to the binding post and tighten the caps down on the spade connector. To reduce the risk of shock or damage to

your amplifier, be sure that the wire connected to one binding post does not come in contact with that of another.

MONO BRIDGE CONNECTIONS: (Figure 9)

Mono bridge operation connections will follow the above descriptions, however, when operating in mono bridge

operation the speaker connections will run between the two positive (red) leads. Use channel two positive

output terminal for the negative connection and the channel one positive output terminal for the positive

connection.

Figure 7

Typical speaker output using bare wire.

Insert bare wire into the binding post and tighten.

page 6

4 Ohm Minimum Speaker Load

Uses Channel 1 Inputs Only

Figure 9

UNiKA

1/5"

13mm

MS550 / MS750 / MS1050 / MS2050 / MS3050

INPUT

CH 2

STEREO BRIDGE

RESET

~120VAC 60Hz

1000 WATTS

PROFESSIONAL POWER AMPLIFIER

CAUTION

4 OHMS MINIMUM IMPEDANCE PRE CHANNEL

8 OHMS MINIMUM IMPEDANCE IN MONO BRIDGE MODE

P2 P3 P1

SERIAL NO.

INPUT

CH 1

MODE

BRIDGE

MONO

CH 1CH 2

OUTPUT

XS 55 0

XS 75 0

XS1 050

XS2 050

XS3 050

Figure 6

Introduction Front Panel Rear Panel Operating Modes Protection SpecificationsSet Up

OPERATING MODES

STEREO OPERATION : Page 7 / Figure 10 details an example of a typical stereo set-up. Connect your inputs into channels one and two of the amplifier.

Connect your speakers to the outputs on the rear of the amplifier. Be sure that your front gain controls are turned down to their lowest level (fully counter-clockwise).

Turn your amplifier on. Turn your input source level up. Use your front gain controls to regulate the output volume. Be sure not to raise the volume to the clip level,

however an intermittent clip signal is acceptable.

MONO BRIDGE OPERATION : 8 Page / Figure 12 details a mono bridge set-up. Be sure your amplifier and all other audio equipment are powered down.

Flip the Stereo/Mono Bridge switch to the Mono Bridge position. Connect an input signal to channel one. Connect your speaker across the red output binding post

on the rear of your amplifier. Turn your equipment on (your amplifier should always be the last item you turn on). Apply an input source signal to your amplifier. Use

the channel one gain control to regulate your amplifier output.

page 7

UNiKA

MS550 / MS750 / MS1050 / MS2050 / MS3050

Typical Speaker

Connect to Channel 2

Output

Typical Speaker

Connect to Channel 1

Output

Typical Stereo Set-Up

Figure 10

Typical Mixer

INPUT

CH 2

STEREO BRIDGE

RESET

~120VAC 60Hz

1000 WATTS

PROFESSIONAL POWER AMPLIFIER

CAUTION

4 OHMS MINIMUM IMPEDANCE PRE CHANNEL

8 OHMS MINIMUM IMPEDANCE IN MONO BRIDGE MODE

P2 P3 P1

SERIAL NO.

INPUT

CH 1

MODE

BRIDGE

MONO

CH 1CH 2

OUTPUT

XS 550

XS 750

XS105 0

XS205 0

XS305 0

Introduction Front Panel Rear Panel Set Up Protection SpecificationsOperating Modes

page 8

SPEAKERS

2 OHM MINIMUM

SPEAKERS

2 OHM MINIMUM

TYPICAL STEREO OUTPUT CONNECTIONS

Figure 11

SPEAKERS

4 OHM MINIMUM

Use Channel 1 Inputs Only

TYPICAL MONO BRIDGE SET-UP

Figure 12

UNiKA

MS550 / MS750 / MS1050 / MS2050 / MS3050

INPUT

CH 2

STEREO BRIDGE

RESET

~120VAC 60Hz

1000 WATTS

PROFESSIONAL POWER AMPLIFIER

CAUTION

4 OHMS MINIMUM IMPEDANCE PRE CHANNEL

8 OHMS MINIMUM IMPEDANCE IN MONO BRIDGE MODE

P2 P3 P1

SERIAL NO.

INPUT

CH 1

MODE

BRIDGE

MONO

CH 1CH 2

OUTPUT

XS 5 50

XS 7 50

XS105 0

XS205 0

XS305 0

INPUT

CH 2

STEREO BRIDGE

RESET

~120VAC 60Hz

1000 WATTS

PROFESSIONAL POWER AMPLIFIER

CAUTION

4 OHMS MINIMUM IMPEDANCE PRE CHANNEL

8 OHMS MINIMUM IMPEDANCE IN MONO BRIDGE MODE

P2 P3 P1

SERIAL NO.

INPUT

CH 1

MODE

BRIDGE

MONO

CH 1CH 2

OUTPUT

XS 5 50

XS 7 50

XS105 0

XS205 0

XS305 0

Introduction Front Panel Rear Panel Set Up Protection SpecificationsOperating Modes

page 9

UNiKA

MS550 / MS750 / MS1050 / MS2050 / MS3050

PROTECTION

SAFE POWER LEVELS AT DIFFERENT OUTPUT LOADS:

8-Ohm Loads : The amplifier can operate at its rated power level without risk of overheating. However, it may caused excessive temperature if it

is pushed hard enough to continually light the “CLIP ” indicator, the amplifier’s average output can reach it's maximum peak.

4-Ohm Loads : If the “CLIP ” indicator flashes occasionally, the amplifier is approaching its Maximum long-term power capacity. If it is lit about

half the time, the amplifier channel will probably go into thermal protection within a few minutes.

2-Ohm Loads : Except for an occasional flash, keep the “CLIP ” indicator dark to avoid overheating the amplifier channel. Clipping should be kept

to a reasonable minimum. An amplifier’s peak current draw at full output power into 2 ohms is several times what the “normal ” draw is, but its

various protection circuits will prevent this condition lasting more than a minute or two.

SHORT CIRCUIT PROTECTION - The MS series amplifiers comes with built-in Output Short Circuit Protects. The Output Short

Circuit Protection protects the output devices of the amplifier from short circuits and stressful loads. If your speaker lines shorted, the

amplifier automatically detects this problem and discontinued operation for that channel. If one side of your amplifier becomes shorted

and goes into protect mode, the other side will continue to operate normally. Channel output during the “Short Circuit Protection" will

be interrupted (i.e. no sound output). Short Circuit Protection can usually be traced back to the signal output line (i.e. speaker line).

Check the line from the output terminal of the amplifier to the speaker. If this line is good, check the internal speaker connections and

components. A short circuit will usually be traced to a bad cable or a bad speaker component and is rarely traced to the amplifier itself.

INPUT/OUTPUT PROTECTION - The input circuits are isolated by resistors. An ultrasonic network uncouples RF from the output and helps to keep the

amplifier stable with reactive loads.

OPERATING VOLTAGE (AC MAINS) - On the rear panel will indicate the correct AC mains voltage. Connecting to the wrong voltage is dangerous and

may damage the amplifier. Always be sure the source voltage for your areas matches the required voltage for your amplifier.

GAIN CONTROLS - The gain controls are located on the front panel and are calibrated in 2dB of attenuation from full gain. It is best to a d j ust the amplifier