Antari S-500 Snow Machine Manuel utilisateur

1

S-500 / S-500L

Snow Machine

User Manual

Engli sh Français Deutsch • • • 中文

2

3

User Manual

Safety Information

Please read the following safety information carefully before operating the

machine. This information includes important safeguards about installation,

usage, and maintenance. Pay attention to all warning labels and instructions in

this manual and printed on the machine.

If you have questions about how to operate the machine safely, please contact your local

Antari dealer for help.

․ Keep this device dry.

․ Always connect to a grounded circuit to avoid risk of electrocution.

․ Before connecting the machine to power, always check the voltage indicated on the

machine matches to your local AC voltage. Do not use the machine if the AC power

voltage does not match.

․ Disconnect the machine from AC power before servicing and when not in use.

․ This product is for indoor use only! Do not expose to rain or moisture. If fluid is spilled,

disconnect AC power and clean with a damp cloth. If fluid is spilled onto electronic

parts, immediately unplug the machine and contact your local Antari dealer for advice.

․ No user serviceable and modifiable parts inside. Never try to repair this product, an

unauthorized technician may cause damage or malfunction to the machine.

․ For adult use only. Never leave the machine running unattended.

․ Install the machine in a well-ventilated area. Provide at least 50 cm of space around

the machine.

․ Never add flammable liquid of any kind to the machine.

․ Make sure there are no flammable materials close to the machine while operating.

․ Only use Antari fluid. Other fluid may lead to a heater clog and malfunction.

․ If the machine fails to work, unplug the machine and stop operation immediately.

Contact your local Antari dealer for advice.

4

․ Before transporting the machine, make sure the fluid tank is completely drained.

․ Snow fluid may present health risks if swallowed. Do not drink snow fluid. Store it

securely. In case of eye contact or if fluid is swallowed, immediately look for medical

advice.

5

Unpacking and Inspection

Immediately upon receiving the machine, carefully unpack the carton, check the content to

ensure that all parts are present and have been received in good condition. If any parts

appear damaged or mishandled from shipping, notify the shipper immediately and retain the

packing material for inspection.

What is included: 1 x S-500 Snow Machine

1 x Power Cord

1 x User Manual

1 x Fluid Tank Feed Tube

1 x 20 Liter Fluid Tank

1 x Air Hose 10 Meters for S-500 / 20 Meters for S-500L

1 x Nozzle

6

Product Dimensions

S-500 Model

S-500L Model

551 mm

651 mm

592 mm

603 mm

651 mm

803mm

7

Product Overview

S-500 Control Panel

Nozzle

Tank Capacity: 20 liters

XLR 5-Pin DMX Connector

XLR 3-Pin DMX Connector

Neutrik PowerCon

SC-3 Remote Control (Optional)

Breaker

Main Power Switch

Wireless Antenna

Control Panel

8

Setting Up

Step 1: Place the machine on a flat surface and in a suitably large area with at least 50 cm

open space around the machine.

Step 2: Fill the fluid tank with Antari approved fluid.

Step 3: Connect the machine to a suitably rated power supply. To determine the power

requirement for the machine refer to the label on the back of the machine.

Always connect the machine to a protected circuit and ensure it is properly

grounded to avoid risk of electrocution.

Step 4: Turn on the machine, press the [VOLUME]/[DOWN] button on the control panel to

start making snow.

Step 5: To turn off the machine, press the [STOP] button and put the power switch to the

OFF position.

PM-1 Pan Motor (Optional)

9

Operation

Control Panel Operation

The machine can be operated with onboard digital control interface

Button

Function

[MENU]

Scroll through setting menu

[UP]/[TIMER]

Up/Activate Timer function

[DOWN]/[VOLUME]

Down/Activate Volume function

[STOP]

Deactivate Timer/Volume function, Escape from menu

Control Menu

Set interval time at timer mode from 15 to 360 sec

Set duration time at timer mode from 5 to 120 sec

Set output volume in Timer mode between 1 and 100 %

Set output volume in Volume mode between 1 and 100 %

Set fan speed from 20 to 100%

Timer Interval

XXX Sec

Timer Duration

XXX Sec

Timer Output

XXX %

Volume Output

XXX %

Fan Speed

XXX %

Antari S-500

Ready to Snow

10

Set DMX/W-DMX address from 1 to 511

Turn On/Off W-DMX function

Unlink from a W-DMX transmitter

Turn On/Off wireless remote feature

Pair/unpair wireless remote.

*This menu will not be shown when Wireless is turned off.

Turn On/Off run last setting function

DMX Connector Pin Assignment

The machine provides a 3- or 5-pin XLR connector for DMX connection. The diagram below

indicates pin assignment information.

Function

1

Ground

2

Data-

3

Data+

W-DMXPower

XX

DMX-512

Address: XXX

W-DMX Reset

XX

Wireless Register

Up:Pair Down:Del

Run Last Setting

XX

Wireless

XX

11

DMX Operation

Making the DMX Connection – Connect the machine to a DMX controller or to one of the

machines in the DMX chain. The machine uses a 3-pin XLR connector for DMX connection,

the connector is located on the rear of the machine.

Address Setup – Use control menu to set DMX address. The machine occupies 2 control

channels. The starting address is defined as the first channel from which the machine will

respond to the controller. Always double check to make sure there are no overlapping

channles in order to control the machine correctly.

DMX Channel Function

Channel 1

DMX Value Range

Function

Snow Output Level

0 – 5

Snow off

6 – 255

Snow Output 1 – 100%

Channel 2

DMX Value Range

Function

Fan Output Level

0 – 5

Fan 20%

6 – 255

Fan 21 – 100%

WTR-20 Wireless Remote Kit Operation

Wireless remote control system W-2 consists of a transmitter equipped with two buttons to

activate, deactivate and adjust output level; with an onboard receiver attached to the front

panel of S-500 snow machine.

12

W-2 Wireless Transmitter

Wireless Receiver

Button

Function

[A]

Activate output

[B]

Deactivate output

[C]

Increase output level

[D]

Decrease output level

In a free open space the effective distance is 50 meters, actual usage depends on obstacle

level; the effective distance is 10-25 meters.

Registering a transmitter

Transmitters can be paired or deleted from the receiver. Each receiver can pair up to 10

transmitters. Follow below diagram to pair or delete transmitter.

IMPORTANT NOTE: Wireless register menu will only be shown when Wireless is turn ON

Transmitter battery replacement

13

If the effective distance seems to decrease, it is possible the battery level is low and

requires replacement. In order to replace the battery, undo the three screws on the back of

transmitter to release the cover. Replace with same type and specification of battery which

is 27A 12V.

SC-3 Wire remote Operation (Optional)

Wired remote control module SC-3 enables to control the machine from a remote location.

With three push buttons and two rotary knobs to activate/deactivate, priming and output

level adjustment.

Button/Knob

Function

[TOP LEFT KNOB]

Adjust pump output level

[TOP RIGHT KNOB]

Adjust blower output level

[LEFT BUTTON]

Max output on pump and blower

[CENTER BUTTON]

Turn On/Off SC-3 remote

[RIGHT BUTTON]

Max output on blower

IMPORTANT NOTE:

[LEFT BUTTON] is meant for priming use, with a new tank of fluid or refill the fluid may not

pump properly due to airlock in the pipeline, use this function to activate pump at maximum

output, the [RIGHT BUTTON] is used when needed to clean out residue at the tip of output

14

nozzle. Both of these buttons will overtake output adjustment knobs.

Physical Installation

Important

 Use supplied mounting bracket or rigging clamp to install nozzle.

 Make sure installation location, fastening connecting, and rigging hardware can hold at

least 10 times the weight of the nozzle.

 Make sure no combustible or flammable materials are nearby.

 Secure nozzle with an approved safety cable that can hold at least 10 times the weight

of nozzle.

 Make sure nozzle is installed in a well ventilated area.

 Consider nozzle replacement and routine maintenance access when selecting

installation location.

Adjustable Mouting Bracket

Adjust mounting bracket by loosening screws, set the nozzle to desired angle and tighten

the screw to finish adjustment. Illustration below demostrates how to adjust mounting

bracket.

Mounting

Use screws for surface mounting or clamps for truss mounting.

15

ST-10 Air Hose Extension (Optional)

The maximum air hose length is 20 meters. Illustration below demostrates how to connect

extension air hose.

Fluid

Only use Antari SL-5/SL-5A/SL-5N/SL-5AN liquid for the S-500 Snow Machine. The

machine is tested and calibrated with this liquid to get the best output performance.

Warranty will be void if any other type of liquid is used, improper use of liquid may lead to

machine failure and malfunction.

Service and Maintenance

․ Do not allow the machine to become contaminated.

․ Remove dust from air vents with air compressor, vacuum or a soft brush.

․ Only use a damp cloth to clean the casing.

ST-10 10M Extension hose

16

․ Before storing run distilled water through the system to help avoid condensing the

pump or heater.

․ It is recommended to run the machine on a monthly basis in order to achieve best

performance and output condition.

․ Excessive dust, liquid and dirt built up will degrade performance and cause

overheating.

․ Before storing away after operation, pump pure water through the system for at least 1

to 2 minutes. This will help clean out the remaining snow fluid and prevent pump from

malfunction on next usage.

Breaker Reset

Disconnect AC power before resetting the breaker. Only replace fuse with same

type and rating.

Step 1: Disconnect power cord from supply.

Step 2: Flip breaker to ON position.

Step 3: Turn on machine for testing.

Breaker

120V = 10A 250V

240V = 5A 250V

17

Technical Specifications

S-500

- Input voltage

- Rated power

- Fluid consumption

- Fluid tank capacity

- Compatible fluid

- Operating time

- Ambient temp. range

- Control

- DMX channels

- Connection

- Optional accessories

- Dimension

- Weight

S-500L

- Dimension

- Weight

US model : AC 100-120V, 50 / 60Hz 7.5A

EU model : AC 220-240V, 50 / 60Hz 3.8A

880W

400 ml/min

20l (5.28gal)

Antari SL-20N Snow Foam Fluid

Antari SL-20AN Premium Snow Fluid

50 mins at max. output

5 °C - 40 °C (41 °F-104 °F)

DMX512, Timer, Manual

Wireless (Optional)

Wireless DMX (Optional)

2 channels

Neutrik Powercon (Power)

XLR 3-pin and 5-pin (DMX)

W-DMX-PCBR Wireless DMX 512

WTR-20 Wireless Remote

WTR-70 Wireless DMX 512 and Remote

SC-3 Cable Remote

ST-10 10 Meters Extension Hose

PM-1 Pan Motor

L592 W551 H651 mm

(L23.31 W21.69 H25.63 inch)

37.2 kg (82.01 lbs)

L803 W603 H651 mm

(L31.61 W23.74 H25.63 inch)

46.4 kg (102.29 lbs)

18

Mode d'emploi

Notices de sécurité

En vue d'utiliser correctement votre nouvel appareil, veuillez lire attentivement

ce mode d'emploi. Pour assurer la longévité et le bon fonctionnement de votre

machine à fumée, veuillez lire attentivement les instructions suivantes

concernant le maniement, la sécurité et l'entretien. Veuillez suivre toute

instruction de sécurité appliquée sur le boîtier de votre machine à neige Antari.

Si vous avez des questions sur l'usage de la machine en toute sécurité, contactez votre

revendeur Antari.

․ Protéger de l'humidité.

․ Utilisez uniquement des prises de courant à terre à 3 broches.

․ Avant la première mise en marche, assurez-vous que l'appareil soit branché à

l'alimentation correcte. Ne jamais utiliser la machine quand la voltage n'est pas

correcte.

․ Débranchez l'appareil du secteur avant d'entretien ou quand vous n'utilisez pas la

machine.

․ L'appareil a été conçu pour un emploi dans des locaux clos. Protéger de l'humidité. En

cas de projection de liquide, débranchez l'appareil du secteur et nettoyez avec un

chiffon humide. Si du liquide devait pénétrer à l’intérieur de l’appareil, débranchez le

immédiatement et contactez un technicien ou votre revendeur Antari avant de le

réutiliser.

․ A l'intérieur de l'appareil, il n'y a aucune partie qui ait besoin d'être révisée. Ne jamais

essayer de reparer le produit parce quet détruire la machine.

․ L'usage de cet appareil n'est prévu que pour les adultes. Ne jamais faire marcher sans

surveillance.

․ Installez l'appareil à un endroit bien aéré. Pour garantir une aération suffisante, laissez

un espace libre de 50 cm tout autour de l’appareil.

19

․ Ne jamais mélanger des liquides enflammables gazeuz ou huileux avec le liquide à

fumée.

․ Respectez une distance minimum de 50 cm entre le bec de la machine et les

matériaux enflammables.

․ Employez uniquement des liquides à neige de haute qualité à base d'eau Antari ou

liquides recommandée par votre revendeur. D'autres liquides à fumée pourraient

causer des problèmes d'encrassage ou des crachotements.

․ Si votre machine à fumée Antari ne devait plus fonctionner correctement, éteignez le

immédiatement. S'il vous plaît contactez votre revendeur Antari.

․ Faites attention à ce que le réservoir soit toujours complètement vidé avant d’envoyer

ou transporter l’appareil.

․ Ne jamais avaler le liquide à fumée. Stocker avec prudence. Si c’était tout de même le

cas, consultez un médecin immédiatement.

Déballage & inspection

Ouvrez le carton extérieur et assurez vous que toutes les pièces n'aient subi aucun

dommage durant leur transport. En cas de livraison endommagée ou incomplète, toujours

contactez immédiatement votre revendeur Antari.

Contenu de la livraison : 1 x S-500 Machine à neige

1 x Câble d'alimentation

1 x Mode d'emploi

1 x Flexible de remplissage

1 x Réservoir 20 litres

1 x Tuyau 10 metres (S-500) / 20 metres (S-500L)

1 x Bec

20

Dimensions du produit

S-500 Model

S-500L Model

Descriptif du droduit

551 mm

651 mm

592 mm

Panneau de contrôle

Disjoncteur

Commutateur secteur

Antenne

Panneau de contrôle

603 mm

651 mm

803 mm

La page est en cours de chargement...

Antari S-500 Snow Machine Manuel utilisateur

Antari S-500 Snow Machine Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents