Dell fi-412PR Manuel utilisateur

Taper
Manuel utilisateur

Ce manuel convient également à

fi-412PR Imprinter
O
O
p
p
e
e
r
r
a
a
t
t
o
o
r
r
s
s
G
G
u
u
i
i
d
d
e
e
P3PC-E947-01XA
Operators Guide
Guide de lutilisateur
Bedienungshandbuch
Guida dell’operatore
Guía del Usuario
オペレーターガイド
fi-412PR Imprinter
O
O
p
p
e
e
r
r
a
a
t
t
o
o
r
r
s
s
G
G
u
u
i
i
d
d
e
e
P3PC-E947-01EN
Contents
Introduction................................................................................................................................................. 1
1. Preparations............................................................................................................................................ 4
1.1. Inspect the Package Contents..............................................................................................................................................4
1.2. Names of Component Parts ................................................................................................................................................4
2. Installation............................................................................................................................................... 5
2.1. Installing the Imprinter .........................................................................................................................................................5
2.2. Loading the Print Ink Cartridge...........................................................................................................................................7
2.3. Operation Test.......................................................................................................................................................................8
3. Basic Operation ...................................................................................................................................... 9
3.1. Setting The Print Position....................................................................................................................................................9
3.2. How to Use the Paper Guides .............................................................................................................................................9
3.3. Print Setup...........................................................................................................................................................................10
3.4. Replacing the Print Cartridge............................................................................................................................................11
3.5. Removing Jammed Documents........................................................................................................................................13
4. Daily Care .............................................................................................................................................. 14
4.1. Cleaning the Print Cartridge..............................................................................................................................................14
4.2. Cleaning the Imprinter .......................................................................................................................................................14
4.3. Cleaning the Rollers...........................................................................................................................................................15
4.4. Cleaning Material ................................................................................................................................................................15
5. Error Messages..................................................................................................................................... 16
6. Specifications ....................................................................................................................................... 17
All Rights Reserved, Copyright © PFU LIMITED 2004.
The contents of this manual are subject to change without notice.
This manual may not be reproduced, adapted or translated without prior written permission.
READ ALL OF THIS MANUAL CAREFULLY BEFORE USING THIS PRODUCT. IF THIS PRODUCT IS NOT USED
CORRECTLY, UNEXPECTED INJURY MAY BE CAUSED TO USERS OR BYSTANDERS.
While all efforts have been made to ensure the accuracy of all information in this manual, PFU LIMITED assumes no
liability to any party for any damage caused by errors or omissions or by statements of any kind in this manual, its
updates or supplements, whether such errors are omissions or statements resulting from negligence, accidents, or any
other cause.
PFU LIMITED further assumes no liability arising from the application or use of any product or system described herein;
nor any liability for incidental or consequential damages arising from the use of this manual.
PFU LIMITED disclaims all warranties regarding the information contained herein, whether expressed, implied, or
statutory.
PFU LIMITED assumes no liability for incidental or consequential damages arising from the use of this product, and any
claims by a third party.
fi-412PR Imprinter Operator’s Guide | 1
Introduction
Thank you for purchasing the fi-412PR Imprinter
option for fi-4120C2 Color Image Scanner.
This guide explains how to install and use the imprinter.
(For further details about the functions and operations of
fi-4120C2 Image Scanner, refer to the “fi-4120C2 Image
Scanner Operators Guide” included in fi-4120C2 Setup
CD-ROM.)
This guide also contains other important information, such
as procedures for replacement of consumables. Keep this
guide in a convenient and safe place so that you can refer
to it whenever necessary.
We hope this manual will be helpful in your future use of
the fi-412PR Imprinter
Manufacturer
PFU LIMITED
Image Products Sales Dept.
Imaging Products Division, Products Group
Solid Square East Tower
580 Horikawa-cho
Saiwai-ku, Kawasaki-shi
Kanagawa 212-8563
Japan
Phone: +81 (44) 540-4538
Trademarks
Microsoft, Windows, and Windows NT are registered
trademarks of Microsoft Corporation in the United States
and/or other countries.
Other product names are the trademarks or registered
trademarks of the respective companies.
How Trademarks Are Indicated In This Manual
References to operating systems (OS) are indicated as
follows:
Windows 95: Microsoft
®
Windows
®
95 operating system.
Windows NT 4.0:
Microsoft
®
Windows NT
®
Server operating
system version 4.0
Microsoft
®
Windows NT
®
Workstation operating
system version 4.0.
Windows 98: Microsoft
®
Windows
®
98 operating system.
Windows Me: Microsoft
®
Windows
®
Millennium Edition
operating system.
Windows 2000: Microsoft
®
Windows
®
2000 Professional
operating system.
Windows XP: Microsoft
®
Windows
®
XP Professional
operating system,
Microsoft
®
Windows
®
XP Home Edition
operating system.
Where there is no distinction between the different
versions of the above operating system, the general term
"Windows" is used.
Regulatory Information
FCC declaration
This equipment has been tested and found to comply
within the limits of a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference
by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase separation between equipment and receiver.
- Connect equipment to an outlet on a circuit different
from that to which the receiver is located.
- Consult your dealer or an experienced radio/TV
technician.
FCC Warning: Changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Canadian DOC Regulations
This digital apparatus does not exceed the Class B limit for
radio noise emissions from digital apparatus set out in the
Radio interference Regulations of the Canadian
Department of Communications.
This Class B digital apparatus complies with Canadian
ICES-003.
Le pésent appareil numérique n’ément pas de bruits
radioélectriques dépassant les limites applicables aux
appareils numériques de la classe B prescridtes dans le
Réglesment sur le brouillage radioélectrique dicté par le
ministere des Communications du Canada.
Cet appareil numérique de la classe B est conformme à la
norme NMB-003 du Canada.
Bescheinigung des Herstellers / Importeurs
Hiermit wird bescheinigt, daß der/die/das
fi-412PR
In Übereinsstimmung mit den Bestimmungen der
EN45014(CE) funkentstört ist.
Laut Maschinenlärminformationsverordnung 3. GS
GV, 18.01.1991:Der höchste Schalldruckpegel beträgt
70 dB (A) order weniger gemäß ISO/7779.
2 |
Use in High-safety Applications
This product has been designed and manufactured on the
assumption that it will be used in office, personal, domestic,
regular industrial, and general-purpose applications. It has
not been designed and manufactured for use in applications
(simply called "high-safety applications" from here on)
that directly involve danger to life and health when a high
degree of safety is required, for example, in the control of
nuclear reactions at nuclear power facilities, automatic
flight control of aircraft, air traffic control, operation
control in mass-transport systems, medical equipment for
sustaining life, and missile firing control in weapons
systems, and when provisionally the safety in question is
not ensured. The user should use this product with
adopting measures for ensuring safety in such high-safety
applications. PFU LIMITED assumes no liability
whatsoever for damages arising from use of this product by
the user in high-safety applications, and for any claims or
compensation for damages by the user or a third party.
Conventions
Warning Indications Used In This Manual
WARNING
This indication alerts operators to an operation
that, if not strictly observed, may result in
severe injury or death.
CAUTION
This indication alerts operators to an
operation that, if not strictly observed, may
result in safety hazards to personnel or
damage to equipment.
Symbols Used In This Manual
This manual, in addition to the above warning indications,
uses the following symbols in its explanations.
ATTENTION
This symbol alerts operators to particularly
important information. Be sure to read this
information.
HINT
This symbol alerts operators to helpful advice
regarding a procedure.
A TRIANGLE symbol indicates that special care
and attention are required.
The drawing inside the triangle shows the specific
caution.
A CIRCLE with a diagonal line inside indicates an
action that users may not perform.
The drawing inside or under the circle shows the
specific action that is not allowed.
R
Outline characters on a colored background show
instructions users should follow.
It may also include the drawing that shows the
specific instruction.
Screen Examples in This Manual
The screen examples in this manual are subject to change
without notice in the interest of product improvement.
If the actual displayed screen differs from the screen
examples in this manual, operate by following the actual
displayed screen while referring to the User's Manual of
the scanner application you are using.
The screenshots used in this manual are for Windows,
FUJITSU TWAIN 32 Scanner Driver.
About Maintenance
The user must not perform repairs on this product.
Contact the store where you purchased the scanner or an
authorized FUJITSU Image Scanner service provider to
have repairs made on this product.
fi-412PR Imprinter Operator’s Guide | 3
Safety Precautions
FOLLOW THESE INSTRUCTIONS AND BE SURE TO
HEED ALL WARNINGS AND CAUTIONS DESCRIBED
BELOW.
WARNING
Do not touch the power plug with wet hands, since
doing so can cause electric shocks.
A damaged AC cable can cause fire or electric shock.
Do not place heavy objects on AC cables, or pull,
bend, twist, heat, damage or modify AC cables.
Do not use damaged AC cables or power plugs. Do
not install AC cables or power plugs in loose wall
sockets.
Do not use cables other than the ones supplied with
this product. Use only specified AC and connector
cables. Failure to use the correct cables can cause
electric shock and/or equipment failure.
Use this scanner only at the indicated power voltage
and current. Improper power voltage and current might
cause fire, electric shock and/or equipment failure.
Do not connect to multiple-power strips.
Wipe off any dust from metal parts on the power plug
or metal fittings with a soft, dry cloth. Accumulated
dust can cause fire or electric shock.
Do not install the scanner in locations subject to oil,
smoke, steam, humidity, and dust. Doing so might
cause a fire or electric shock or equipment failure.
If you detect heat coming from the device or detect
other problems such as smoke, strange smells or
noises, immediately turn off the scanner and then
disconnect its power plug.
Make sure that the smoke has stopped and, then
contact the store where you bought the scanner or an
authorized FUJITSU scanner service provider.
If the scanner is damaged for any reason, turn off the
scanner and unplug the power cable before contacting
the store where you purchased the scanner.
Do not insert or drop metal objects into the scanner.
Do not scan wet documents or documents with paper
clips or staples.
Do not splash liquids on or allow the scanner to get
wet.
If foreign objects (dirt, small objects, metal, liquids,
etc.) get inside the scanner, immediately turn off the
scanner and disconnect the power plug from the
power outlet, then contact the store where you bought
the scanner or the Maintenance Service Center. Pay
particular attention to this warning in households
where there are small children.
Do not take apart or modify the scanner. The inside of
the scanner contains high-voltage components.
Touching these components might cause electric
shock or fire.
CAUTION
The following describes important cautions.
Make sure that the scanner is installed on a flat, level
surface and that none of its parts extend beyond the
surface top, such as a desk or table.
Do not install the scanner on unstable surfaces.
Install the scanner on a level surface that is free of
vibration to prevent it from falling.
Install the scanner on a strong surface that will
support the weight of the scanner and other devices.
Firmly insert the power plug as far it can go into the
power outlet.
Install the scanner away from strong magnetic fields
and other sources of electronic noise. Also, protect
the scanner from static electricity as this might cause
the scanner to malfunction.
Do not use aerosol sprays to clean the scanner.
Aerosol sprays cause dirt and dust to enter the
scanner resulting in scanner failure and malfunction.
When the scanner will not be used for a long period,
for safety precautions, be sure to disconnect the
power plug from the power outlet.
Do not place the scanner in direct sunlight or near a
heating apparatus, as excessive heat can build up
inside the scanner and cause fire or scanner-related
troubles. Install the scanner in a well-ventilated
location.
Do not block the ventilation ports. Blocking the
ventilation ports generates heat inside of scanner,
which may result in fire or scanning failure.
Do not place heavy objects on the scanner or use the
scanner's surface top to perform other work.
Improper installation might cause injuries and
equipment failure.
Do not move the scanner with the power and
interface cables connected as this can damage the
cables, which can later cause fire, electric shock as
well as injury.
Before moving the scanner, be sure to disconnect
the power plug from the power outlet, and all other
data cables.
Make sure that the floor is free of any obstructions.
Avoid touching any scanner mechanism when the
scanner is turned on or during scanning since this
may cause injuries.
Do not use the device immediately after moving it
from a cold place to a warm room. This may cause
condensation, which might lead to scanning errors.
Let the device dry about one or two hours before you
use it.
4 |
1. Preparations
1.1. Inspect the Package Contents
When you open the imprinter package, please handle the
main unit and its attachments carefully.
Make sure it contains all the parts listed in the package
contents list that is included in the imprinter package box.
If any of the components are missing, please contact the
store where you purchased the imprinter.
1.2. Names of Component Parts
<Imprinter Unit>
Front Side
Rear Side
<Imprinter with Scanner Installed>
Front Side
Rear Side
Open Print Cartridge Cover
Stacker
ADF (Automatic Document Feeder)
ADF Paper Chute
Operator Panel
Function No. display
[Function] button
[Send to] button
[Scan] button
Power button
LED
Paper Guide
Print Cartridge Cover Print Cartridge Holder
Print section
Print Cartridge Cover
EXT Cable
(Imprinter Cable)
Fix Tab
fi-412PR Imprinter Operator’s Guide | 5
2. Installation
2.1. Installing the Imprinter
Install the imprinter as follows:
1. Press the button to switch off the Scanner and
disconnect the electrical power cable.
2. Remove the Stacker from the scanner as shown
below.
1) Hold the left side of the stacker with left hand.
2) While pressing on the scanner with your thumb, pull the
stacker gently away from the scanner.
3) When the left side of the stacker has been released from
the scanner, remove the right side of the stacker.
ATTENTION
You must remove the stacker before installing
the scanner to the imprinter.
3. Remove the two screws located at the back of the
scanner.
4. Install the Scanner on to the Imprinter.
Hold the Scanner above the rear side of the Imprinter and
gently place the Scanner on to the base of the Imprinter
while lowering it forward until it makes contact with the
Imprinter.
ATTENTION
Be careful not to place the Scanner on to
the Fix Tabs or hit hard against them as
you might damage the Fix Tabs.
Take care not to pinch your fingers.
2
Carefully pull the stacker
out.
1 Press your thumb on the scanner.
About 80 degrees
Stacker
After installation
Fix Tab
6 |
5. Insert the screws attached to the Fix Tabs into the
two positions in the rear of the Imprinter; and
tighten them to secure the imprinter to the
Scanner.
6. Join the Imprinter cable (EXT Cable) to the
connector in the rear of the Scanner.
ATTENTION
The Imprinter will not work if the EXT cable is
not connected to the Scanner. Scanning
when the EXT cable is not connected can
cause documents to jam inside the Imprinter.
7. Replace the Stacker (removed in procedure 2) to
the Imprinter.
8. Connect the power cable to the scanner.
d Reconnect the other arm by
sliding it in gently.
c Insert one arm.
fi-412PR Imprinter Operator’s Guide | 7
2.2. Loading the Print Ink Cartridge
Load the print ink cartridge as follows:
ATTENTION
When installing or replacing the print cartridge, be
careful not to insert it out of place.
1. Confirm that the scanner is turned off.
2. To open the cover, grasp and pull open the center
of the Print Cartridge Cover turning it open
towards you.
3. Remove by pulling the tape seal that is affixed to
the Print Cartridge Holder and the Paper Guides.
4. Pinch slightly together the handles with your
fingers, as shown below, to release it from its
cartridge tray holder and turn it upwards to open
the tray holder.
5. Remove the new print cartridge from its pouch.
6. Remove the protection tape from the print
cartridge.
ATTENTION
Do not touch the metal part of the cartridge nor put
the tape back on again.
7. Place the Print Cartridge into the holder as shown
below.
ATTENTION
Be careful not to let the Print Cartridge touch
or catch onto the print circuit film.
8. Lower the handle until it locks in and fixes the
cartridge in place.
9. Position the Print Cartridge Holder along where
the document will pass through.
Ö The print will be located on the page properly for
your application.
10. Close the print cartridge cover.
Print Cartrid
g
e Holde
r
8 |
2.3. Operation Test
After installing the Imprinter, check if the printing
operation can be done in the Offline Print Test mode of the
scanner.
1. While pressing the [Function] button on the
operator panel, press the button.
Continue pressing the [Function] button.
2. Release the [Function] button when the Function
Number Display changes from [P] to [b].
3. Place a blank document into the ADF paper
chute.
ATTENTION
Use A4 or Letter size paper. If the size is
smaller than A4 or Letter, printing may not
complete successfully.
Confirm that the Print Cartridge is
positioned within the document width.
4. Press [Scan] button to test.
Ö The paper will feed into the ADF, and the Imprinter
will print out the Print Test Characters starting at
5mm from the papers edge
HINT
Print Test Patterns
Test Pattern 1 (Horizontal):
ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`00000000
Test Pattern 2 (Horizontal:
abcdefghijklmnopqrstuvwxyz{|}~ 00000000
Test Pattern 3 (Horizontal):
!”#$%&()*+,-./0123456789:;<=>?@00000000
Test Pattern 4(Vertical):
ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`00000000
Test Pattern 5 (Vertical):
abcdefghijklmnopqrstuvwxyz{|}~ 00000000
Test Pattern 6 (Vertical):
!”#$%&()*+,-./0123456789:;<=>?@00000000
When multiple sheets of documents are placed in the
ADF, the Test Print repeats patterns from 1 through 6.
The numbering data portion ”00000000” changes from
0 (Zero) with increment of 1(one).
(One test pattern is printed at a time. Press the [Scan]
button to continue printing the next test pattern.)
5. To stop Offline Print test mode, press the
button. The scanner will switch off.
5mm
c d e f g h
Feeding direction
Print Test Sample
Function
Function
Function
Send to
Scan
Function Number Display
fi-412PR Imprinter Operator’s Guide | 9
3. Basic Operation
3.1. Setting The Print Position
To position the print cartridge for printing:
1. Open the Print Cartridge Cover.
2. Hold the print cartridge holder, as below, and
slide it to the left or right within the document
width to set it at a suitable print starting position.
HINT
The small “” protruding from the upper right
hand side of the print cartridge tray handle
indicates the current print position on the
page.
Above the print cartridge tray are document
size markings; please use them to adjust for
paper size and printing position.
Put the actual document in the ADF and
confirm that the print cartridge is positioned
within the document’s width.
3.2. How to Use the Paper Guides
Use the Paper Guides to prevent against paper jams due to
curling of the edges, as shown below.
Place the Paper Guides at the ends where the paper edges
will pass through.
1. Insert the document in the scanner.
2. Open the Print Cartridge Cover.
3. Slide the Paper Guides to the left and right of the
page edges.
HINT
When you wish to print on the near the edges of
a wide width paper, remove the Paper Guide in
order to open space for the Print Cartridge, and
attach it at the center.
For Right Side Edge Printing
For Left Side Edge Printing
ATTENTION
Be careful not to let the Paper Guide touch or
catch onto the print circuit film.
Paper Guide
Feed direction
10 |
To Remove the Paper Guides
Pressing and holding together with your fingers, as below,
lift up and pull away the guide.
To Attach the Paper Guides
1. The Paper Guides should be in place as in the
picture on the left.
2. The top portion of the guide should be pushed in
to fit tightly.
3.3. Print Setup
You can configure settings for the imprinter by using the
scanner driver dialog box.
FUJITSU TWAIN driver (Example)
Click [Option] button.
In [Option] dialog box, choose [Imprinter (Endorser)] tab and
specify the Imprinter settings.
HINT
Available items are:
Y offset (Printing)
• Font orientation
• Strings definition Max. 40 characters
• Counter Setup column, add/subtract, step
For the details, please refer to “FUJITSU TWAIN 32
Scanner Driver User’s Guide” or “TWAIN Driver Help”
Paper Guide
Paper Guide
Paper Guide
fi-412PR Imprinter Operator’s Guide | 11
3.4. Replacing the Print Cartridge
Replace the Print Cartridge as follows:
ATTENTION
When the following message appears, replace
the Print Cartridge as soon as possible.
When installing or replacing the print cartridge,
be careful not to insert it out of place, If you
continue to print without replacing the cartridge,
your print output will continue to appear lighter
and lighter.
When installing or replacing the print cartridge,
be careful not to insert it out of place.
1. Press the button to turn off the Scanner.
2. Open the cover by grasping the center of the Print
Cartridge Cover and pull it open while turning the
cover downward towards you, as exhibited below.
3. Pinch slightly the handles of the closing lever to
release it from its cartridge tray holder and turn it
upwards to open the tray holder.
4. Remove the old Print Cartridge from the Print
Cartridge Holder.
5. Take the new Print Cartridge out of its pouch and
detach the protection tape from the Print
Cartridge.
ATTENTION
Do not touch the metal part of the cartridge nor
put the tape back on again.
6. Insert the Print Cartridge in the holder with its tab
pointing to the right.
7. Lower the closing lever gently until it locks in and
fixes the cartridge in place.
8. Position the Print Cartridge Holder along where
the document will pass through and position the
print on the scanned page properly for your
application.
Print Cartridge Holder
12 |
ATTENTION
Printing too close to a document’s edge can
leave little or no room for further printing, be
sure to position the print cartridge to have
enough space.
9. Close the Print Cartridge Cover.
10. Turn on the scanner.
11. Reset the Ink Remaining Counter.
ATTENTION
You must reset the Ink Remain Counter
whenever you replace the print cartridge.
For Windows 98, Windows Me, Windows 2000, Windows XP
c On the [Start] menu, select [Control panel].
d Select [Scanners and Cameras].
e On the fi-4120C2 Scanner icon,
right click and select [Properties] (for Windows Me,
Windows XP),
or double click (for Windows 98, Windows 2000).
f Select [Device Set] tab.
g Click [Clear] button on [Remaining Ink].
Ö The Remaining Ink Counter is reset to 100%.
h Click [OK] button.
i The confirmation window will be displayed. Click [OK]
button.
For Windows 95, Windows NT 4.0
c Right-click the icon in taskbar and select [Option].
d Select [Device Setting tab.
e Click [Clear] button on [Remaining Ink].
Ö The Remaining Ink Counter is reset to 100%.
f Click [OK] button.
g The confirmation window will be displayed. Click [OK]
button.
fi-412PR Imprinter Operator’s Guide | 13
3.5. Removing Jammed Documents
Remove jammed documents sheets as follows:
ATTENTION
Do not forcefully pull out the documents pages.
1. Remove the documents that are not jammed in
the imprinter or scanner feed from the ADF Paper
chute.
2. Holding the right side of the Imprinter Cover, pull
open the cover turning it towards you.
ATTENTION
To open the ADF Cover, first open the
Imprinter Cover before proceeding.
3. Open the ADF by pulling it back gently.
4. Carefully remove all jammed documents.
5. Close the ADF cover.
6. Close the Imprinter Cover.
ATTENTION
To close the Imprinter Cover, be sure that the
ADF cover is closed first before closing the
Imprinter Cover
ATTENTION
Be careful not to pinch your fingers.
Do not move the imprinter or scanner while
printing.
When not using the imprinter for a long
period, please remove the print cartridge
from the imprinter and store it.
Each time the imprinter is turned on some ink
is initially consumed.
Do not move the scanner with the imprinter
already installed. The imprinter may become
damaged.
ADF Cove
r
Imprinter Cover
ADF Cove
r
Imprinter Cover
14 |
4. Daily Care
4.1. Cleaning the Print Cartridge
Poor quality prints may occur due to blocked ink emission
holes in the nozzle. Leaving the imprinter unused for long
periods can also cause emission holes to become blocked.
When the emission holes are blocked, clean the nozzle
surface of the print cartridge.
ATTENTION
For cleaning, use a dry lint-free cloth (DO NOT use
tissue), and gently wipe any dirt and stains off the
nozzle’s surface.
1. Press the button to turn off the Scanner.
2. Remove the Print Cartridge.
(Refer to “3.4. Replacing the Print Cartridge”)
ATTENTION
When cleaning, be careful not to touch directly
by hand the Nozzle plate or any of the contact
parts on the cartridge.
3. Gently wipe any dirt and stains off the nozzle
surface.
4. Make sure that all dirt and stains are removed,
before installing the print cartridge.
(Refer to “3.4. Replacing the Print Cartridge”)
ATTENTION
When installing or replacing the print
cartridge, be careful not to insert it out of
place.
4.2. Cleaning the Imprinter
After frequent use, ink will begin to accumulate or stick to
the base of the imprinter, which can soil printouts. Always
maintain the imprinter base clean.
To assure high quality print outs and long use of the
imprinter, adopt a daily maintenance procedure as given
below.
ATTENTION
When cleaning, wipe off gently all dust and
ink on the imprinter base..
If the ink has dried, wipe it lightly with a
water-moistened cloth.
1. Press the button to turn off the Scanner.
2. Open the Print Cartridge Cover and remove the
print cartridge.
(Refer to “3.4. Replacing the Print Cartridge”)
3. Open the Imprinter Cover.
4. Clean the print cartridge holder base by wiping off
any dirt and dust with a lint-free cloth.
When cleaning, be careful not to touch the
metal wheels located behind the upper rollers
on the print cartridge cover.
5. Check that the dirt is wiped off, and then close the
imprinter cover.
6. Reinstall the print cartridge and close the print
cartridge cover.
(Refer to “3.4. Replacing the Print Cartridge”)
Nozzle plate
fi-412PR Imprinter Operator’s Guide | 15
4.3. Cleaning the Rollers
When ink or dust from paper is stuck on the imprinter feed
roller surfaces, documents may not feed smoothly. To
prevent feed problems, clean the rollers’ surfaces regularly.
HINT
Recommended cleaning cycle is every 1,000 sheets.
Actual cleaning cycle may be shorter depending on
usage and documents.
1. Open the imprinter cover.
2. Clean the roller surfaces with a lint-free cloth
moistened with Cleaner F1 by wiping off all dirt
and dust.
Clean the lower rubber rollers (total of six) by holding
down both the [Scan] and [Send to] buttons on the
front panel of the scanner and rotating the rollers.
ATTENTION
When cleaning, be careful not to touch the
metal wheels located behind the upper rollers
on the print cartridge holder cover.
3. Cleaning the Plastic Rollers.
Also, clean the two black plastic rollers on the inner
side of the Imprinter cover.
Rotate the rollers with your fingers gently and wipe
off any dirt or dust from the roller surface with a
lint-free cloth moistened with Cleaner F1.
4. Confirm that all dirt and dust have been removed
from the rollers. Close the Imprinter Cover.
4.4. Cleaning Material
Cleaning Materials
Parts No. Remarks
Cleaner F1
CA99501-0013
1 bottle (100ml)
* To purchase the cleaning material, contact the FUJITSU scanner
dealer where you purchased the scanner.
Imprinter Cover
Imprinter Cover
16 |
5. Error Messages
The following numbers or letters on the Function
Number Display indicates a malfunction in the
imprinter.
Description: The print cartridge is not installed.
How to solve: Open the print cartridge cover and confirm that
the print cartridge is installed correctly.
Description: The imprinter fuse has blown out.
How to solve: Turn off the scanner and then turn it on again.
(If the problem occurs again, contact the store
where you purchased the imprinter or contact
an authorized FUJISTU scanner service
provider.)
Description: A problem occurred to the Imprinter.
How to solve: cOpen the print cartridge cover and confirm
that the print cartridge has been installed
correctly.
dTurn off the scanner and then turn it on
again.
eTurn off the scanner and replace the print
cartridge and then turn it on again.
(If the problem occurs again, contact the store
where you purchased the imprinter or contact
an authorized FUJISTU scanner service
provider.)
ATTENTION
For other errors, refer to “fi-4120C2 Image Scanner
Operator’s Guide” included in fi-4120C2 Setup
CD-ROM.
Function
Function
Function
Function
Function
Function
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128

Dell fi-412PR Manuel utilisateur

Taper
Manuel utilisateur
Ce manuel convient également à