Dell fi-412PR Manuel utilisateur

fi-412PR Imprinter

O

p

e

r

a

t

o

r

’

s

G

u

i

d

e

P3PC-E947-01XA

Operator’s Guide

Guide de l’utilisateur

Bedienungshandbuch

Guida dell’operatore

Guía del Usuario

オペレーターガイド

fi-412PR Imprinter

O

p

e

r

a

t

o

r

’

s

G

u

i

d

e

P3PC-E947-01EN

Contents

Introduction................................................................................................................................................. 1

1. Preparations............................................................................................................................................ 4

1.1. Inspect the Package Contents..............................................................................................................................................4

1.2. Names of Component Parts ................................................................................................................................................4

2. Installation............................................................................................................................................... 5

2.1. Installing the Imprinter .........................................................................................................................................................5

2.2. Loading the Print Ink Cartridge...........................................................................................................................................7

2.3. Operation Test.......................................................................................................................................................................8

3. Basic Operation ...................................................................................................................................... 9

3.1. Setting The Print Position....................................................................................................................................................9

3.2. How to Use the Paper Guides .............................................................................................................................................9

3.3. Print Setup...........................................................................................................................................................................10

3.4. Replacing the Print Cartridge............................................................................................................................................11

3.5. Removing Jammed Documents........................................................................................................................................13

4. Daily Care .............................................................................................................................................. 14

4.1. Cleaning the Print Cartridge..............................................................................................................................................14

4.2. Cleaning the Imprinter .......................................................................................................................................................14

4.3. Cleaning the Rollers...........................................................................................................................................................15

4.4. Cleaning Material ................................................................................................................................................................15

5. Error Messages..................................................................................................................................... 16

6. Specifications ....................................................................................................................................... 17

The contents of this manual are subject to change without notice.

This manual may not be reproduced, adapted or translated without prior written permission.

READ ALL OF THIS MANUAL CAREFULLY BEFORE USING THIS PRODUCT. IF THIS PRODUCT IS NOT USED

CORRECTLY, UNEXPECTED INJURY MAY BE CAUSED TO USERS OR BYSTANDERS.

While all efforts have been made to ensure the accuracy of all information in this manual, PFU LIMITED assumes no

liability to any party for any damage caused by errors or omissions or by statements of any kind in this manual, its

updates or supplements, whether such errors are omissions or statements resulting from negligence, accidents, or any

other cause.

PFU LIMITED further assumes no liability arising from the application or use of any product or system described herein;

nor any liability for incidental or consequential damages arising from the use of this manual.

PFU LIMITED disclaims all warranties regarding the information contained herein, whether expressed, implied, or

statutory.

PFU LIMITED assumes no liability for incidental or consequential damages arising from the use of this product, and any

claims by a third party.

fi-412PR Imprinter Operator’s Guide | 1

Introduction

Thank you for purchasing the fi-412PR Imprinter

option for fi-4120C2 Color Image Scanner.

This guide explains how to install and use the imprinter.

(For further details about the functions and operations of

fi-4120C2 Image Scanner, refer to the “fi-4120C2 Image

Scanner Operator’s Guide” included in fi-4120C2 Setup

CD-ROM.)

This guide also contains other important information, such

as procedures for replacement of consumables. Keep this

guide in a convenient and safe place so that you can refer

to it whenever necessary.

We hope this manual will be helpful in your future use of

the fi-412PR Imprinter

Manufacturer

PFU LIMITED

Image Products Sales Dept.

Imaging Products Division, Products Group

Solid Square East Tower

580 Horikawa-cho

Saiwai-ku, Kawasaki-shi

Kanagawa 212-8563

Japan

Phone: +81 (44) 540-4538

Trademarks

Microsoft, Windows, and Windows NT are registered

trademarks of Microsoft Corporation in the United States

and/or other countries.

Other product names are the trademarks or registered

trademarks of the respective companies.

How Trademarks Are Indicated In This Manual

References to operating systems (OS) are indicated as

follows:

Windows 95: Microsoft

®

Windows

®

95 operating system.

Windows NT 4.0:

Microsoft

®

Windows NT

®

Server operating

system version 4.0

Microsoft

®

Windows NT

®

Workstation operating

system version 4.0.

Windows 98: Microsoft

®

Windows

®

98 operating system.

Windows Me: Microsoft

®

Windows

®

Millennium Edition

operating system.

Windows 2000: Microsoft

®

Windows

®

2000 Professional

operating system.

Windows XP: Microsoft

®

Windows

®

XP Professional

operating system,

Microsoft

®

Windows

®

XP Home Edition

operating system.

Where there is no distinction between the different

versions of the above operating system, the general term

"Windows" is used.

Regulatory Information

FCC declaration

This equipment has been tested and found to comply

within the limits of a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may

cause harmful interference to radio communications.

However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference

by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase separation between equipment and receiver.

- Connect equipment to an outlet on a circuit different

from that to which the receiver is located.

- Consult your dealer or an experienced radio/TV

technician.

FCC Warning: Changes or modifications not expressly

approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

Canadian DOC Regulations

This digital apparatus does not exceed the Class B limit for

radio noise emissions from digital apparatus set out in the

Radio interference Regulations of the Canadian

Department of Communications.

This Class B digital apparatus complies with Canadian

ICES-003.

Le pésent appareil numérique n’ément pas de bruits

radioélectriques dépassant les limites applicables aux

appareils numériques de la classe B prescridtes dans le

Réglesment sur le brouillage radioélectrique dicté par le

ministere des Communications du Canada.

Cet appareil numérique de la classe B est conformme à la

norme NMB-003 du Canada.

Bescheinigung des Herstellers / Importeurs

Hiermit wird bescheinigt, daß der/die/das

fi-412PR

• In Übereinsstimmung mit den Bestimmungen der

EN45014(CE) funkentstört ist.

• Laut Maschinenlärminformationsverordnung 3. GS

GV, 18.01.1991:Der höchste Schalldruckpegel beträgt

70 dB (A) order weniger gemäß ISO/7779.

2 |

Use in High-safety Applications

This product has been designed and manufactured on the

assumption that it will be used in office, personal, domestic,

regular industrial, and general-purpose applications. It has

not been designed and manufactured for use in applications

(simply called "high-safety applications" from here on)

that directly involve danger to life and health when a high

degree of safety is required, for example, in the control of

nuclear reactions at nuclear power facilities, automatic

flight control of aircraft, air traffic control, operation

control in mass-transport systems, medical equipment for

sustaining life, and missile firing control in weapons

systems, and when provisionally the safety in question is

not ensured. The user should use this product with

adopting measures for ensuring safety in such high-safety

applications. PFU LIMITED assumes no liability

whatsoever for damages arising from use of this product by

the user in high-safety applications, and for any claims or

compensation for damages by the user or a third party.

Conventions

Warning Indications Used In This Manual

WARNING

This indication alerts operators to an operation

that, if not strictly observed, may result in

severe injury or death.

CAUTION

This indication alerts operators to an

operation that, if not strictly observed, may

result in safety hazards to personnel or

damage to equipment.

Symbols Used In This Manual

This manual, in addition to the above warning indications,

uses the following symbols in its explanations.

ATTENTION

This symbol alerts operators to particularly

important information. Be sure to read this

information.

HINT

This symbol alerts operators to helpful advice

regarding a procedure.

A TRIANGLE symbol indicates that special care

and attention are required.

The drawing inside the triangle shows the specific

caution.

A CIRCLE with a diagonal line inside indicates an

action that users may not perform.

The drawing inside or under the circle shows the

specific action that is not allowed.

R

Outline characters on a colored background show

instructions users should follow.

It may also include the drawing that shows the

specific instruction.

Screen Examples in This Manual

The screen examples in this manual are subject to change

without notice in the interest of product improvement.

If the actual displayed screen differs from the screen

examples in this manual, operate by following the actual

displayed screen while referring to the User's Manual of

the scanner application you are using.

The screenshots used in this manual are for Windows,

FUJITSU TWAIN 32 Scanner Driver.

About Maintenance

The user must not perform repairs on this product.

Contact the store where you purchased the scanner or an

authorized FUJITSU Image Scanner service provider to

have repairs made on this product.

fi-412PR Imprinter Operator’s Guide | 3

Safety Precautions

FOLLOW THESE INSTRUCTIONS AND BE SURE TO

HEED ALL WARNINGS AND CAUTIONS DESCRIBED

BELOW.

WARNING

Do not touch the power plug with wet hands, since

doing so can cause electric shocks.

A damaged AC cable can cause fire or electric shock.

Do not place heavy objects on AC cables, or pull,

bend, twist, heat, damage or modify AC cables.

Do not use damaged AC cables or power plugs. Do

not install AC cables or power plugs in loose wall

sockets.

Do not use cables other than the ones supplied with

this product. Use only specified AC and connector

cables. Failure to use the correct cables can cause

electric shock and/or equipment failure.

Use this scanner only at the indicated power voltage

and current. Improper power voltage and current might

cause fire, electric shock and/or equipment failure.

Do not connect to multiple-power strips.

Wipe off any dust from metal parts on the power plug

or metal fittings with a soft, dry cloth. Accumulated

dust can cause fire or electric shock.

Do not install the scanner in locations subject to oil,

smoke, steam, humidity, and dust. Doing so might

cause a fire or electric shock or equipment failure.

If you detect heat coming from the device or detect

other problems such as smoke, strange smells or

noises, immediately turn off the scanner and then

disconnect its power plug.

Make sure that the smoke has stopped and, then

contact the store where you bought the scanner or an

authorized FUJITSU scanner service provider.

If the scanner is damaged for any reason, turn off the

scanner and unplug the power cable before contacting

the store where you purchased the scanner.

Do not insert or drop metal objects into the scanner.

Do not scan wet documents or documents with paper

clips or staples.

Do not splash liquids on or allow the scanner to get

wet.

If foreign objects (dirt, small objects, metal, liquids,

etc.) get inside the scanner, immediately turn off the

scanner and disconnect the power plug from the

power outlet, then contact the store where you bought

the scanner or the Maintenance Service Center. Pay

particular attention to this warning in households

where there are small children.

Do not take apart or modify the scanner. The inside of

the scanner contains high-voltage components.

Touching these components might cause electric

shock or fire.

CAUTION

The following describes important cautions.

Make sure that the scanner is installed on a flat, level

surface and that none of its parts extend beyond the

surface top, such as a desk or table.

Do not install the scanner on unstable surfaces.

Install the scanner on a level surface that is free of

vibration to prevent it from falling.

Install the scanner on a strong surface that will

support the weight of the scanner and other devices.

Firmly insert the power plug as far it can go into the

power outlet.

Install the scanner away from strong magnetic fields

and other sources of electronic noise. Also, protect

the scanner from static electricity as this might cause

the scanner to malfunction.

Do not use aerosol sprays to clean the scanner.

Aerosol sprays cause dirt and dust to enter the

scanner resulting in scanner failure and malfunction.

When the scanner will not be used for a long period,

for safety precautions, be sure to disconnect the

power plug from the power outlet.

Do not place the scanner in direct sunlight or near a

heating apparatus, as excessive heat can build up

inside the scanner and cause fire or scanner-related

troubles. Install the scanner in a well-ventilated

location.

Do not block the ventilation ports. Blocking the

ventilation ports generates heat inside of scanner,

which may result in fire or scanning failure.

Do not place heavy objects on the scanner or use the

scanner's surface top to perform other work.

Improper installation might cause injuries and

equipment failure.

Do not move the scanner with the power and

interface cables connected as this can damage the

cables, which can later cause fire, electric shock as

well as injury.

Before moving the scanner, be sure to disconnect

the power plug from the power outlet, and all other

data cables.

Make sure that the floor is free of any obstructions.

Avoid touching any scanner mechanism when the

scanner is turned on or during scanning since this

may cause injuries.

Do not use the device immediately after moving it

from a cold place to a warm room. This may cause

condensation, which might lead to scanning errors.

Let the device dry about one or two hours before you

use it.

4 |

1. Preparations

1.1. Inspect the Package Contents

When you open the imprinter package, please handle the

main unit and its attachments carefully.

Make sure it contains all the parts listed in the package

contents list that is included in the imprinter package box.

If any of the components are missing, please contact the

store where you purchased the imprinter.

1.2. Names of Component Parts

Front Side

Rear Side

Front Side

Rear Side

Open Print Cartridge Cover

Stacker

ADF (Automatic Document Feeder)

ADF Paper Chute

Operator Panel

・

Function No. display

・

[Function] button

・

[Send to] button

・

[Scan] button

・

Power button

・

LED

Paper Guide

Print Cartridge Cover Print Cartridge Holder

Print section

Print Cartridge Cover

EXT Cable

(Imprinter Cable)

Fix Tab

fi-412PR Imprinter Operator’s Guide | 5

2. Installation

2.1. Installing the Imprinter

Install the imprinter as follows:

1. Press the button to switch off the Scanner and

disconnect the electrical power cable.

2. Remove the Stacker from the scanner as shown

below.

1) Hold the left side of the stacker with left hand.

2) While pressing on the scanner with your thumb, pull the

stacker gently away from the scanner.

3) When the left side of the stacker has been released from

the scanner, remove the right side of the stacker.

ATTENTION

You must remove the stacker before installing

the scanner to the imprinter.

3. Remove the two screws located at the back of the

scanner.

4. Install the Scanner on to the Imprinter.

Hold the Scanner above the rear side of the Imprinter and

gently place the Scanner on to the base of the Imprinter

while lowering it forward until it makes contact with the

Imprinter.

ATTENTION

● Be careful not to place the Scanner on to

the Fix Tabs or hit hard against them as

you might damage the Fix Tabs.

● Take care not to pinch your fingers.

2

Carefully pull the stacker

out.

1 Press your thumb on the scanner.

About 80 degrees

Stacker

After installation

Fix Tab

6 |

5. Insert the screws attached to the Fix Tabs into the

two positions in the rear of the Imprinter; and

tighten them to secure the imprinter to the

Scanner.

6. Join the Imprinter cable (EXT Cable) to the

connector in the rear of the Scanner.

ATTENTION

The Imprinter will not work if the EXT cable is

not connected to the Scanner. Scanning

when the EXT cable is not connected can

cause documents to jam inside the Imprinter.

7. Replace the Stacker (removed in procedure 2) to

the Imprinter.

8. Connect the power cable to the scanner.

d Reconnect the other arm by

sliding it in gently.

c Insert one arm.

fi-412PR Imprinter Operator’s Guide | 7

2.2. Loading the Print Ink Cartridge

Load the print ink cartridge as follows:

ATTENTION

When installing or replacing the print cartridge, be

careful not to insert it out of place.

1. Confirm that the scanner is turned off.

2. To open the cover, grasp and pull open the center

of the Print Cartridge Cover turning it open

towards you.

3. Remove by pulling the tape seal that is affixed to

the Print Cartridge Holder and the Paper Guides.

4. Pinch slightly together the handles with your

fingers, as shown below, to release it from its

cartridge tray holder and turn it upwards to open

the tray holder.

5. Remove the new print cartridge from its pouch.

6. Remove the protection tape from the print

cartridge.

ATTENTION

Do not touch the metal part of the cartridge nor put

the tape back on again.

7. Place the Print Cartridge into the holder as shown

below.

ATTENTION

Be careful not to let the Print Cartridge touch

or catch onto the print circuit film.

8. Lower the handle until it locks in and fixes the

cartridge in place.

9. Position the Print Cartridge Holder along where

the document will pass through.

Ö The print will be located on the page properly for

your application.

10. Close the print cartridge cover.

Print Cartrid

g

e Holde

r

8 |

2.3. Operation Test

After installing the Imprinter, check if the printing

operation can be done in the Offline Print Test mode of the

scanner.

1. While pressing the [Function] button on the

operator panel, press the button.

Continue pressing the [Function] button.

2. Release the [Function] button when the Function

Number Display changes from [P] to [b].

3. Place a blank document into the ADF paper

chute.

ATTENTION

 Use A4 or Letter size paper. If the size is

smaller than A4 or Letter, printing may not

complete successfully.

 Confirm that the Print Cartridge is

positioned within the document width.

4. Press [Scan] button to test.

Ö The paper will feed into the ADF, and the Imprinter

will print out the Print Test Characters starting at

5mm from the paper’s edge

HINT

Print Test Patterns

Test Pattern 1 (Horizontal):

ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`00000000

Test Pattern 2 (Horizontal）:

abcdefghijklmnopqrstuvwxyz{|}~ 00000000

Test Pattern 3 (Horizontal):

!”#$%&()*+,-./0123456789:;<=>?@00000000

Test Pattern 4(Vertical):

ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`00000000

Test Pattern 5 (Vertical):

abcdefghijklmnopqrstuvwxyz{|}~ 00000000

Test Pattern 6 (Vertical):

!”#$%&()*+,-./0123456789:;<=>?@00000000

When multiple sheets of documents are placed in the

ADF, the Test Print repeats patterns from 1 through 6.

The numbering data portion ”00000000” changes from

0 (Zero) with increment of 1(one).

(One test pattern is printed at a time. Press the [Scan]

button to continue printing the next test pattern.)

5. To stop Offline Print test mode, press the

button. The scanner will switch off.

5mm

c d e f g h

Feeding direction

Print Test Sample

Function

Send to

Scan

Function Number Display

fi-412PR Imprinter Operator’s Guide | 9

3. Basic Operation

3.1. Setting The Print Position

To position the print cartridge for printing:

1. Open the Print Cartridge Cover.

2. Hold the print cartridge holder, as below, and

slide it to the left or right within the document

width to set it at a suitable print starting position.

HINT

● The small “▲” protruding from the upper right

hand side of the print cartridge tray handle

indicates the current print position on the

page.

● Above the print cartridge tray are document

size markings; please use them to adjust for

paper size and printing position.

● Put the actual document in the ADF and

confirm that the print cartridge is positioned

within the document’s width.

3.2. How to Use the Paper Guides

Use the Paper Guides to prevent against paper jams due to

curling of the edges, as shown below.

Place the Paper Guides at the ends where the paper edges

will pass through.

1. Insert the document in the scanner.

2. Open the Print Cartridge Cover.

3. Slide the Paper Guides to the left and right of the

page edges.

HINT

When you wish to print on the near the edges of

a wide width paper, remove the Paper Guide in

order to open space for the Print Cartridge, and

attach it at the center.

For Right Side Edge Printing

For Left Side Edge Printing

ATTENTION

Be careful not to let the Paper Guide touch or

catch onto the print circuit film.

Paper Guide

Feed direction

10 |

To Remove the Paper Guides

Pressing and holding together with your fingers, as below,

lift up and pull away the guide.

To Attach the Paper Guides

1. The Paper Guides should be in place as in the

picture on the left.

2. The top portion of the guide should be pushed in

to fit tightly.

3.3. Print Setup

You can configure settings for the imprinter by using the

scanner driver dialog box.

FUJITSU TWAIN driver (Example)

Click [Option] button.

In [Option] dialog box, choose [Imprinter (Endorser)] tab and

specify the Imprinter settings.

HINT

Available items are:

• Y offset (Printing)

• Font orientation

• Strings definition （Max. 40 characters）

• Counter Setup （column, add/subtract, step）

For the details, please refer to “FUJITSU TWAIN 32

Scanner Driver User’s Guide” or “TWAIN Driver Help”

Paper Guide

fi-412PR Imprinter Operator’s Guide | 11

3.4. Replacing the Print Cartridge

Replace the Print Cartridge as follows:

ATTENTION

• When the following message appears, replace

the Print Cartridge as soon as possible.

• When installing or replacing the print cartridge,

be careful not to insert it out of place, If you

continue to print without replacing the cartridge,

your print output will continue to appear lighter

and lighter.

• When installing or replacing the print cartridge,

be careful not to insert it out of place.

1. Press the button to turn off the Scanner.

2. Open the cover by grasping the center of the Print

Cartridge Cover and pull it open while turning the

cover downward towards you, as exhibited below.

3. Pinch slightly the handles of the closing lever to

release it from its cartridge tray holder and turn it

upwards to open the tray holder.

4. Remove the old Print Cartridge from the Print

Cartridge Holder.

5. Take the new Print Cartridge out of its pouch and

detach the protection tape from the Print

Cartridge.

ATTENTION

Do not touch the metal part of the cartridge nor

put the tape back on again.

6. Insert the Print Cartridge in the holder with its tab

pointing to the right.

7. Lower the closing lever gently until it locks in and

fixes the cartridge in place.

8. Position the Print Cartridge Holder along where

the document will pass through and position the

print on the scanned page properly for your

application.

Print Cartridge Holder

12 |

ATTENTION

Printing too close to a document’s edge can

leave little or no room for further printing, be

sure to position the print cartridge to have

enough space.

9. Close the Print Cartridge Cover.

10. Turn on the scanner.

11. Reset the Ink Remaining Counter.

ATTENTION

You must reset the Ink Remain Counter

whenever you replace the print cartridge.

For Windows 98, Windows Me, Windows 2000, Windows XP

c On the [Start] menu, select [Control panel].

d Select [Scanners and Cameras].

e On the fi-4120C2 Scanner icon,

right click and select [Properties] (for Windows Me,

Windows XP),

or double click (for Windows 98, Windows 2000).

f Select [Device Set] tab.

g Click [Clear] button on [Remaining Ink].

Ö The Remaining Ink Counter is reset to 100%.

h Click [OK] button.

i The confirmation window will be displayed. Click [OK]

button.

For Windows 95, Windows NT 4.0

c Right-click the icon in taskbar and select [Option].

d Select [Device Setting］ tab.

e Click [Clear] button on [Remaining Ink].

Ö The Remaining Ink Counter is reset to 100%.

f Click [OK] button.

g The confirmation window will be displayed. Click [OK]

button.

fi-412PR Imprinter Operator’s Guide | 13

3.5. Removing Jammed Documents

Remove jammed documents sheets as follows:

ATTENTION

Do not forcefully pull out the documents pages.

1. Remove the documents that are not jammed in

the imprinter or scanner feed from the ADF Paper

chute.

2. Holding the right side of the Imprinter Cover, pull

open the cover turning it towards you.

ATTENTION

To open the ADF Cover, first open the

Imprinter Cover before proceeding.

3. Open the ADF by pulling it back gently.

4. Carefully remove all jammed documents.

5. Close the ADF cover.

6. Close the Imprinter Cover.

ATTENTION

To close the Imprinter Cover, be sure that the

ADF cover is closed first before closing the

Imprinter Cover

ATTENTION

● Be careful not to pinch your fingers.

● Do not move the imprinter or scanner while

printing.

● When not using the imprinter for a long

period, please remove the print cartridge

from the imprinter and store it.

● Each time the imprinter is turned on some ink

is initially consumed.

● Do not move the scanner with the imprinter

already installed. The imprinter may become

damaged.

ADF Cove

r

Imprinter Cover

ADF Cove

r

Imprinter Cover

14 |

4. Daily Care

4.1. Cleaning the Print Cartridge

Poor quality prints may occur due to blocked ink emission

holes in the nozzle. Leaving the imprinter unused for long

periods can also cause emission holes to become blocked.

When the emission holes are blocked, clean the nozzle

surface of the print cartridge.

ATTENTION

For cleaning, use a dry lint-free cloth (DO NOT use

tissue), and gently wipe any dirt and stains off the

nozzle’s surface.

1. Press the button to turn off the Scanner.

2. Remove the Print Cartridge.

(Refer to “3.4. Replacing the Print Cartridge”)

ATTENTION

When cleaning, be careful not to touch directly

by hand the Nozzle plate or any of the contact

parts on the cartridge.

3. Gently wipe any dirt and stains off the nozzle

surface.

4. Make sure that all dirt and stains are removed,

before installing the print cartridge.

(Refer to “3.4. Replacing the Print Cartridge”)

ATTENTION

When installing or replacing the print

cartridge, be careful not to insert it out of

place.

4.2. Cleaning the Imprinter

After frequent use, ink will begin to accumulate or stick to

the base of the imprinter, which can soil printouts. Always

maintain the imprinter base clean.

To assure high quality print outs and long use of the

imprinter, adopt a daily maintenance procedure as given

below.

ATTENTION

● When cleaning, wipe off gently all dust and

ink on the imprinter base..

● If the ink has dried, wipe it lightly with a

water-moistened cloth.

1. Press the button to turn off the Scanner.

2. Open the Print Cartridge Cover and remove the

print cartridge.

(Refer to “3.4. Replacing the Print Cartridge”)

3. Open the Imprinter Cover.

4. Clean the print cartridge holder base by wiping off

any dirt and dust with a lint-free cloth.

When cleaning, be careful not to touch the

metal wheels located behind the upper rollers

on the print cartridge cover.

5. Check that the dirt is wiped off, and then close the

imprinter cover.

6. Reinstall the print cartridge and close the print

cartridge cover.

(Refer to “3.4. Replacing the Print Cartridge”)

Nozzle plate

fi-412PR Imprinter Operator’s Guide | 15

4.3. Cleaning the Rollers

When ink or dust from paper is stuck on the imprinter feed

roller surfaces, documents may not feed smoothly. To

prevent feed problems, clean the rollers’ surfaces regularly.

HINT

Recommended cleaning cycle is every 1,000 sheets.

Actual cleaning cycle may be shorter depending on

usage and documents.

1. Open the imprinter cover.

2. Clean the roller surfaces with a lint-free cloth

moistened with Cleaner F1 by wiping off all dirt

and dust.

Clean the lower rubber rollers (total of six) by holding

down both the [Scan] and [Send to] buttons on the

front panel of the scanner and rotating the rollers.

ATTENTION

When cleaning, be careful not to touch the

metal wheels located behind the upper rollers

on the print cartridge holder cover.

3. Cleaning the Plastic Rollers.

Also, clean the two black plastic rollers on the inner

side of the Imprinter cover.

Rotate the rollers with your fingers gently and wipe

off any dirt or dust from the roller surface with a

lint-free cloth moistened with Cleaner F1.

4. Confirm that all dirt and dust have been removed

from the rollers. Close the Imprinter Cover.

4.4. Cleaning Material

Cleaning Materials

Parts No. Remarks

Cleaner F1

CA99501-0013

1 bottle (100ml)

* To purchase the cleaning material, contact the FUJITSU scanner

dealer where you purchased the scanner.

Imprinter Cover

16 |

5. Error Messages

The following numbers or letters on the Function

Number Display indicates a malfunction in the

imprinter.

Description: The print cartridge is not installed.

How to solve: Open the print cartridge cover and confirm that

the print cartridge is installed correctly.

Description: The imprinter fuse has blown out.

How to solve: Turn off the scanner and then turn it on again.

(If the problem occurs again, contact the store

where you purchased the imprinter or contact

an authorized FUJISTU scanner service

provider.)

Description: A problem occurred to the Imprinter.

How to solve: cOpen the print cartridge cover and confirm

that the print cartridge has been installed

correctly.

dTurn off the scanner and then turn it on

again.

eTurn off the scanner and replace the print

cartridge and then turn it on again.

(If the problem occurs again, contact the store

where you purchased the imprinter or contact

an authorized FUJISTU scanner service

provider.)

ATTENTION

For other errors, refer to “fi-4120C2 Image Scanner

Operator’s Guide” included in fi-4120C2 Setup

CD-ROM.

Function

La page charge ...

Dell fi-412PR Manuel utilisateur

Ce manuel convient également à

Dell fi-412PR Manuel utilisateur

dans d''autres langues

Autres documents