Marvel 30ARM-BS-F-R Mode d'emploi

Marque: Marvel

Modèle: 30ARM-BS-F-R

Catégorie: Boissons glacées

Taper: Mode d'emploi

Beverage center

Stockage de boissons

ML24BCG0

EN Installation, Operation and Maintenance Instructions

FR Instructions d’installation, d’utilisation et d’entretien

NOTE

CAUTION

CONTENTS

Contents:

Safety information ...............................................................2

Unpacking your beverage center ........................................3

Warranty registration .....................................................3

Installing your beverage center ..........................................4

Cabinet clearances .........................................................4

Leveling the appliance ....................................................4

Electrical connection ......................................................5

Product Dimensions ...........................................................6

Using your Electronic control .............................................8

Starting your beverage center .......................................8

Turning your beverage center "ON" or "OFF" ................8

Set the temperature .......................................................8

Beverage center operation ............................................8

Alarms ............................................................................8

Door ajar ....................................................................8

Temperature sensor fault ...........................................8

High and Low temperature ........................................8

Alarm mute ....................................................................8

Shelving congurations ......................................................9

Care and cleaning .............................................................10

Energy saving tips ............................................................10

Obtaining service .............................................................11

Troubleshooting ................................................................12

Warranty ...........................................................................13

Important Safety Instructions

Warnings and safety instructions appearing in this guide

are not meant to cover all possible conditions and situa-

tions that may occur. Common sense, caution, and care

must be exercised when installing, maintaining, or operat-

ing this appliance.

Recognize Safety Symbols,

Words, and Labels.

WARNING

WARNING-You can be killed or seriously injured if

you do not follow these instructions.

CAUTION-Hazards or unsafe practices which could re-

sult in personal injury or property / product damage.

NOTE-Important information to help assure a problem

free installation and operation.

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause cancer.

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause birth defects or

other reproductive harm..

NOTE

CAUTION

XXXXXXXXXXXX

UNPACKING YOUR BEVERAGE CENTER

WARNING

WARNING - Help Prevent Tragedies

Child entrapment and suffocation are not problems of

the past. Junked or abandoned refrigerators are still

dangerous - even if they sit out for "just a few hours".

If you are getting rid of your old refrigerator, please

follow the instructions below to help prevent acci-

dents.

Before you throw away your old refrigerator or

freezer:

• Take off the doors or remove the drawers.

• Leave the shelves in place so children may not

easily climb inside.

WARNING

WARNING - Dispose of the plastic bags which can

be a suffocation hazard.

MARVEL

Warranty Registration

It is important you send in your warranty registration card

immediately after taking delivery of your appliance or you

can register online at www.marvelrefrigeration.com.

The following information will

be required when registering

your appliance.

Service Number

Serial Number

Date of Purchase

Dealer’s name and address

The service number and serial number can be found on the

serial plate which is located inside the cabinet on the left

side near the top. (See gure 1).

WARNING

EXCESSIVE WEIGHT HAZARD

Use two or more people to move product.

Failure to do so can result in personal injury.

Remove Interior Packaging

Your appliance has been packed for shipment with all parts

that could be damaged by movement securely fastened.

Remove internal packing materials and any tape holding in-

ternal components in place. The owners manual is shipped

inside the product in a plastic bag along with the warranty

registration card, and other accessory items.

Important

Keep your carton and packaging until your appliance has

been thoroughly inspected and found to be in good condi-

tion. If there is damage, the packaging will be needed as

proof of damage in transit. Afterwards please dispose of all

items responsibly.

Note to Customer

This merchandise was carefully packed and thoroughly

inspected before leaving our plant. Responsibility for its

safe delivery was assumed by the retailer upon acceptance

of the shipment. Claims for loss or damage sustained in

transit must be made to the retailer.

DO NOT RETURN DAMAGED MERCHANDISE TO THE

MANUFACTURER - FILE THE CLAIM WITH THE

RETAILER.

If the appliance was shipped, handled, or stored in other

than an upright position for any period of time, allow the ap-

pliance to sit upright for a period of at least 24 hours before

plugging in. This will assure oil returns to the compressor.

Plugging the appliance in immediately may cause damage

to internal parts.

Figure 1

Online registra-

tion available at

www.marvelrefrig-

eration.com

CAUTION

WARNING

An optional stacking kit is required to stack products.

Failure to use a stacking kit could result in personal

injury. Contact your dealer or Marvel customer service

at 800-223-3900 to order.

Select Location

The proper location will ensure peak performance of your

beverage center. We recommend a location where the unit

will be out of direct sunlight and away from heat sources.

To ensure your product performs to specications, the rec-

ommended installation location temperature range is from

55 to 100°F (13 to 38°C).

Cabinet Clearance

Ventilation is required from the bottom front of the beverage

center. Keep this area open and clear of any obstructions.

Adjacent cabinets and counter top can be installed around

the beverage center as long as the front grille remains

unobstructed.

Front Grille

Do not obstruct the front grille. The openings within the

front grille allow air to ow through the condenser heat ex-

changer. Restrictions to this air ow will result in increased

energy usage and loss of cooling capacity. For this reason

it is important this area not be obstructed and the grille

openings kept clean. Marvel does not recommend the use

of a custom made grille as air ow may be restricted. (See

Figure 2).

Front Leveling

Legs

Figure 2

Rear

Leveling

Legs

Front Grille,

keep this area

open.

INSTALLING YOUR BEVERAGE CENTER

Leveling Legs

Adjustable legs at the front and rear corners of the bever-

age center should be set so the unit is rmly positioned

on the oor and level from side to side and front to back.

The overall height of your Marvel beverage center may be

adjusted between the minimum, 33

⁄4" (85.7 cm), by turning

the leveling leg in (CW ↷) and the maximum, 34

⁄4" (88.3

cm) by turning the leveling leg out (CCW ↶).

To adjust the leveling legs, place the beverage center on a

solid surface and protect the oor beneath the legs to avoid

scratching the oor. With the assistance of another person,

lean the beverage center back to access the front leveling

legs. Raise or lower the legs to the required dimension by

turning the legs. Repeat this process for the rear by tilt-

ing the beverage center forward using caution. On a level

surface check the beverage center for levelness and adjust

accordingly.

The front grille screws may be loosened and the grille ad-

justed to the desired height. When adjustment is complete

tighten the two front grille screws. (See Figure 5).

NOTE

Figure 6

Figure 3

Figure 4

Do not remove

ground prong

Electrical Shock Hazard

• Do not use an extension cord with this appliance.

They can be hazardous and can degrade product

performance.

• This appliance should not, under any circumstanc-

es, be installed to an un-grounded electrical supply.

• Do not remove the grounding prong from the power

cord. (See Figure 3).

• Do not use an adapter. (See Figure 4).

• Do not splash or spray water from a hose on the

appliance. Doing so may cause an electrical shock,

which may result in severe injury or death.

WARNING

Electrical Connection

A grounded 115 volt, 15 amp dedicated circuit is required.

This product is factory equipped with a power supply

cord that has a three-pronged, grounded plug. It must be

plugged into a mating grounding type receptacle in accor-

dance with the National Electrical Code and applicable lo-

cal codes and ordinances (see Figure 6). If the circuit does

not have a grounding type receptacle, it is the responsibility

and obligation of the customer to provide the proper power

supply. The third ground prong should not, under any cir-

cumstances, be cut or removed.

Ground Fault Circuit Interrupters (GFCI) are prone to nui-

sance tripping which will cause the appliance to shut down.

GFCI’s are generally not used on circuits with power equip-

ment that must run unattended for long periods of time, un-

less required to meet local building codes and ordinances.

Front grille screw

Front grille

Figure 5

INSTALLING YOUR BEVERAGE CENTER

MODEL

ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS

"A" "B" "C" "D" "E" "F" "G" "H" "J"

ML24BCG0

24"

(61 cm)

**34" to 35"

(86.4 to 88.9 cm)

⁄8"

(60.7 cm)

⁄4" to 34

⁄4"

(85.7 to 88.3 cm)

⁄32"

(60.2 cm)

⁄32"

(65.2 cm)

⁄32"

(117.9 cm)

⁄16"

(65.2 cm)

"A"

"B"

"C"

"D"

"E"

PRODUCT DIMENSIONS

Figure 7a

If necessary to gain clearance inside the rough-in

opening a hole can be cut through the adjacent cabi-

net and the power cord routed through this hole to a

power outlet. Another way to increase the available

opening depth is to recess the power outlet into the

rear wall to gain the thickness of the power cord plug.

Not all recessed outlet boxes will work for this applica-

tion as they are too narrow, but a recessed outlet box

equivalent to Arlington #DVFR1W is recommended for

this application, (see Figure 8).

Figure 8

Figure 7

"F"

⁄2"

(54.6 cm)

* Depth dimension of rough-in opening may vary depend-

ing on each individual installation. To recess entire door "F"

dimension plus 1" (2.5 cm) for thickness of power cord plug

is required.

** Minimum rough-in opening required is to be larger than

the adjusted height of the cabinet.

# A grounded 15 amp dedicated circuit is required. Follow

all local building codes when installing electrical and appli-

ance.

MODEL

PRODUCT DATA

ELECTRICAL

REQUIREMENTS #

PRODUCT

WEIGHT

ML24BCG0 115V/60Hz/15A

140 lbs

(63.6 kg)

"D"

"E"

"H"

"J"

"G"

PRODUCT DIMENSIONS

Figure 9

USING YOUR ELECTRONIC CONTROL

Starting your beverage center

Plug the beverage center power cord into a wall outlet. Your

beverage center will begin cooling after power is applied.

If your beverage center does not start, check that the bev-

erage center is turned on and the set temperature is cold

enough.

Turning your beverage center ON or OFF

If the beverage center is on, the beverage center tempera-

ture will be shown on the display. To turn the beverage

center off, press and hold the "ON/OFF" button for three (3)

seconds. "OFF" will appear on the display.

If the beverage center is not on, "OFF" will be shown on

the display. To turn the beverage center on, press and hold

the "ON/OFF" button for three (3) seconds. The beverage

center temperature will be shown on the display.

Set temperature

To set the beverage center temperature, press and hold

the "SET" button. When the "SET" button is pressed, the

display will show the set temperature. While holding the

"SET" button, press the "WARMER" or "COLDER" buttons

to adjust set temperature.

Beverage center operation

The available temperature range of the beverage center is

34° to 42°F (1° to 6° C).

It may take up to 24 hours for your beverage center to

reach desired temperature. This will depend on amount of

content loaded and number of door opening and closings.

For best results allow beverage center to "pull down" to

desired set temperature before loading. Once contents are

loaded, allow at least 48 hours for temperature to stabilize

before making any adjustments to the set temperature.

Alarms

Your Marvel Prime Controls™ will monitor beverage center

function and alert you with a series of audible and visual

alarms.

• Temperature Sensor Fault: If the control-

ler detects that the temperature sensor is

not properly functioning, a temperature

sensor alarm will sound in one (1) second intervals. "E1"

will ash on the display panel and the Alarm LED located

at the top left of the display below the word "Alarm" will be

illuminated. Please call Marvel Customer Service or your

dealer if this error code is displayed.

• High and Low Temperature Alarm: If the

storage compartment temperature deviates

excessively from the set-point temperature, the

alarm will sound in (1) second intervals. The

display panel will ash either "Hi" or "Lo" de-

pending upon the condition and the Alarm LED

light at the top left of the display below the word

"Alarm" will be illuminated. The alarm will remain active

until the condition is corrected.

Set

Colder Warmer

ON/OFF

Press and Hold Press and Hold

Alarm

Figure 11

Control

Assembly

Figure 10

close-up of

control

Light Switch

Door Switch

Control

• Door Ajar Alarm: If the door has been left

open for over ve (5) minutes, the alarm

will sound in one (1) second intervals. The

display panel will ash "do" and the Alarm LED located at

the top left of the display below the word "Alarm" will be il-

luminated. This will stop as soon as the door is closed.

NOTE

Alarm Mute

Press any key to mute the audible portion of an alarm.

This action will only mute the alarm. If the condition that

caused the alarm continues, the alarm code will continue to

ash and will sound for 20 seconds every 60 minutes.

NOTE

After a high temperature alarm condition, check all perish-

ables to ensure they are safe for consumption.

The temperature alarm may occur as a result of high usage

or introduction of warm contents to the storage compart-

ment. If the temperature alarm continues to occur, your unit

may require service.

Figure12

SHELVING CONFIGURATIONS

Beverage center:

Loading Tips and Suggestions

Your beverage center is equipped with a cantilever shelf

system which provides maximum adjust ability and custom-

izing of the shelving arrangements listed below.

24" (61 cm) Wide Models:

Shown with a glass door. Figure 12.

(2) perforated metal

cantilever shelves.

(See Figure 13).

Figure 13

Perforated metal shelf

To Add or Remove a Shelf

Remove stored product from the shelf. Do not try to remove

a loaded shelf from the beverage center. Grasp the shelf

front with both hands, rotate the front upward and lift out.

(See Figure 14). To install a shelf insert the shelf in the ap-

pliance and insert the top hooks into the shelf support slots

and drop the shelf down so the hooks drop over the bottom

of the slots.

Make sure your cantilever shelf is secure on the shelf sup-

ports by pressing down on the shelf before loading.

CAUTION

Never try to move a loaded shelf, remove everything from

the shelf before moving. Use both hands when moving the

shelf.

Rear tang

(hook) on

shelf

Shelf support

slot

Installed shelf

tang

Figure 14a

Figure 14

CARE AND CLEANING AND ENERGY SAVING TIPS

CAUTION

The beverage center uses one, 25 watt incandescent

light bulb to illuminate the interior. The light bulb is a very

reliable electrical component, but should it not function

properly, please call the dealer where you purchased your

wine cellar from for a replacement light bulb. Use only an

original equipment light bulb from your dealer or Marvel.

To replace the light bulb, disconnect power to the unit. Un-

screw the old light bulb located behind the display housing

at the top of the unit. Set the old light bulb aside. Screw

the new light bulb into place. Reconnect power to the unit.

Check to see if the light bulb operates properly to complete

the installation.

The light bulb is not covered by your warranty. A replace-

ment bulb can be obtained from your dealer or from Marvel.

WARNING

DISCONNECT THE POWER CORD BEFORE

ATTEMPTING LIGHT BULB REPLACEMENT.

Failure to do so may result in an electrical shock

that could severely injure you.

Do NOT under any circumstance use a light bulb

that exceeds 25 watts!

Front Grille

Be sure that nothing obstructs the required air ow open-

ings in front of the cabinet. At least once or twice a year,

brush or vacuum lint and dirt from the front grille area (see

page 4).

SHOCK HAZARD: Disconnect electrical power from the

appliance before cleaning with soap and water.

Cabinet

The painted cabinet can be washed with either a mild soap

and water and thoroughly rinsed with clear water. NEVER

use abrasive scouring cleaners.

Interior

Wash interior compartment with mild soap and water. Do

NOT use an abrasive cleaner, solvent, polish cleaner or

undiluted detergent.

Care of Appliance

1. Avoid leaning on the door, you may bend the door

hinges or tip the appliance.

2. Exercise caution when sweeping, vacuuming or mop-

ping near the front of the appliance. Damage to the

grille can occur.

3. Periodically clean the interior of the appliance as

needed.

4. Periodically check and/or clean the front grille as

needed.

In the Event of a Power Failure

If a power failure occurs, try to correct it as soon as pos-

sible. Minimize the number of door openings while the

power is off so as not to adversely affect the appliance's

temperature.

Light bulb replacement

The following suggestions will minimize the

cost of operating your refrigeration appliance.

1. Do not install your appliance next to a hot appliance

(cooker, dishwasher, etc.), heating air duct, or other

heat sources.

2. Install product out of direct sunlight.

3. Ensure the front grille vents at front of appliance be-

neath door are not obstructed and kept clean to allow

ventilation for the refrigeration system to expel heat.

4. Plug your appliance into a dedicated power circuit. (Not

shared with other appliances).

5. When initially loading your new product, or whenever

large quantities of warm contents are placed within

refrigerated storage compartment, minimize door

openings for the next 12 hours to allow contents to pull

down to compartment set temperature.

6. Maintaining a relatively full storage compartment will

require less appliance run time than an empty compart-

ment.

7. Ensure door closing is not obstructed by contents

stored in your appliance.

8. Allow hot items to reach room temperature before plac-

ing in product.

9. Minimize door openings and duration of door openings.

10. Use the warmest temperature control set temperature

that meets your personal preference and provides the

proper storage for your stored contents.

11. When on vacation or away from home for extended pe-

riods, set the appliance to warmest acceptable tem-

perature for the stored contents.

12. Set the control to the "off" position if cleaning the

appliance requires the door to be open for an extended

period of time.

OBTAINING SERVICE

If Service is Required:

• If the product is within the rst year warranty period

please contact your dealer or call Marvel Customer

Service at 800.223.3900 for directions on how to obtain

warranty coverage in your area.

• If the product is outside the rst year warranty period,

Marvel Customer Service can provide recommenda-

tions of service centers in your area. A listing of autho-

rized service centers is also available at www.marvelre-

frigeration.com under the service and support section.

• In all correspondence regarding service, be sure to

give the service number, serial number, and proof of

purchase.

• Try to have information or description of nature of the

problem, how long the appliance has been running, the

room temperature, and any additional information that

may be helpful in quickly solving the problem.

• Table "A" is provided for recording pertinent information

regarding your product for future reference.

For Your Records

Date of Purchase

Dealer’s name

Dealer’s Address

Dealer’s City

Dealer’s State

Dealer’s Zip Code

Appliance Serial Number

Appliance Service Number

Date Warranty Card Sent (Must

be within 10 days of purchase).

Table A

• Never attempt to repair or perform maintenance on

the appliance until the main electrical power has been

disconnected. Turning the appliance control "OFF"

does not remove electrical power from the unit's wiring.

• Replace all parts and panels before operating.

WARNING

Electrocution Hazard

Before You Call for Service

If the appliance appears to be malfunctioning, read through

this manual rst. If the problem persists, check the trouble-

shooting guide below. Locate the problem in the guide and

refer to the cause and its remedy before calling for service.

The problem may be something very simple that can be

solved without a service call. However, it may be required

to contact your dealer or a qualied service technician.

TROUBLESHOOTING

Problem Possible Cause Remedy

Appliance not cold enough

(See "Set temperature" on page 8)

• Control set too warm

• Content temperature not stabi-

lized.

• Excessive usage or prolonged

door openings.

• Airow to front grille blocked.

• Door gasket not sealing properly.

• Adjust temperature colder. Al-

low 24 hours for temperature to

stabilize.

• Allow temperature to stabilize for

at least 24 hours.

• Airow must not be obstructed to

front grille. See "clearances" on

page 4.

• Replace door gasket.

Appliance too cold

(See "Set temperature" on page 8)

• Control set too cold

• Door gasket not sealing properly.

• Adjust temperature warmer.

Allow 24 hours for temperature to

stabilize.

• Replace door gasket.

No interior light. • Light bulb is burned out • Replace light bulb, see page 10.

Light will not go out when door is

closed

• Display light is turned on. (Glass

door models only.

• Door not activating light switch.

• Failed light switch

• Turn off display light, shut door.

• Appliance not level, level appli-

ance, (See page 4, "leveling legs")

• Contact a qualied service techni-

cian.

Noise or Vibration • Appliance not level

• Fan hitting tube obstruction.

• Level appliance, see "Leveling

Legs" on page 4.

• Contact a qualied service techni-

cian.

Appliance will not run. • Appliance turned off

• Power cord not plugged in.

• No power at outlet.

• Turn appliance on. See "Starting

your beverage center" on page 8.

• Plug in power cord.

• Check house circuit.

CAUTION

In the unlikely event you lose cooling in your unit, do not

unplug the product from the electric supply, but do call

a qualied service technician immediately. It is possible

that the loss of cooling capacity is a result of excessive

frost build-up on the evaporator cooling coil. In this case,

removing power to the unit will result in the melting of this

excessive quantity of ice, which could generate melt water

that exceeds the capacity of the defrost drain system and

could result in water damage to your home. The end-user

will be ultimately responsible for any water damage caused

by prematurely turning the unit off without appropriately

managing the excess water run-off.

HOUSEHOLD PRODUCT WARRANTY

Marvel Refrigeration (Marvel) Limited Warranty

ONE YEAR LIMITED PARTS & LABOR WARRANTY

For one year from the date of original purchase, this warranty covers all parts and labor to repair or replace any part of the product that proves to

be defecve in materials or workmanship. For products installed and used for normal residenal use, material cosmec defects are included in this

warranty, with coverage limited to 60 days from the date of original purchase. All service provided by Marvel under the above warranty must be

performed by a Marvel factory authorized servicer, unless otherwise specied by Marvel. Service provided during normal business hours.

TWO YEAR LIMITED PARTS & LABOR WARRANTY (MARVEL PROFESSIONAL PRODUCTS)

For two years from the date of original purchase, this warranty covers all parts and labor to repair or replace any part of the product that proves to

be defecve in materials or workmanship. For products installed and used for normal residenal use, material cosmec defects are included in this

warranty, with coverage limited to 60 days from the date of original purchase. All service provided by Marvel under the above warranty must be

performed by a Marvel factory authorized servicer, unless otherwise specied by Marvel. Service provided during normal business hours.

AVAILABLE THIRD YEAR LIMITED WARRANTY (MARVEL PROFESSIONAL PRODUCTS)

For designated Marvel Professional product, Marvel oers a one year extension of the two year warranty coverage from the date of purchase, free

of charge. To take advantage of this third year warranty, you must register your product with Marvel within 60 days from the date of purchase at

marvelrefrigeraon.com and provide proof of purchase.

LIMITED FIVE YEAR SEALED SYSTEM WARRANTY

For ve years from the date of original purchase, Marvel will repair or replace the following parts, labor not included, that prove to be defecve in

materials or workmanship: compressor, condenser, evaporator, drier, and all connecng tubing. All service provided by Marvel under the above war-

ranty must be performed by a Marvel factory authorized servicer, unless otherwise specied by Marvel. Service provided during normal business

hours.

WARRANTY TERMS

These warranes apply only to products installed in any one of the y states of the United States, the District of Columbia, or the ten provinces of

Canada. The warranes do not cover any parts or labor to correct any defect caused by negligence, accident or improper use, maintenance, instal-

laon, service, repair, acts of God, re, ood or other natural disasters. The product must be installed, operated, and maintained in accordance with

the Marvel User Guide.

The remedies described above for each warranty are the only ones that Marvel will provide, either under these warranes or under any warranty

arising by operaon of law. Marvel will not be responsible for any consequenal or incidental damages arising from the breach of these warranes

or any other warranty, whether express, implied, or statutory. Some states do not allow the exclusion or limitaon of incidental or consequenal

damages, so the above limitaon or exclusion may not apply to you. These warranes give you specic legal rights, and you may also have other

rights which vary from state to state.

Any warranty that may be implied in connecon with your purchase or use of the product, including any warranty of merchantability or any war-

ranty t for a parcular purpose is limited to the duraon of these warranes, and only extends to ve years in duraon for the parts described

in the secon related to the ve year limited warranty above. Some states do not allow limitaons on how long an implied warranty lasts, so the

above limitaons may not apply to you.

• The warranes only apply to the original purchaser and are non-transferable.

• These warranes cover products installed and used for normal residenal use only.

• The warranes apply to units operated outside only if designed for outdoor use by model and serial number.

• Replacement water lters, light bulbs, and other consumable parts are not covered by these warranes.

• The start of Marvel’s obligaon is limited to four years aer the shipment date from Marvel.

• In-home instrucon on how to use your product is not covered by these warranes.

• Food, beverage, and medicine loss are not covered by these warranes.

• If the product is located in an area where Marvel factory authorized service is not available, you may be responsible for a trip charge or

you may be required to bring the product to a Marvel factory authorized service locaon at your own cost and expense.

• Units purchased aer use as oor displays, and/or cered recondioned units, are covered by the limited one year warranty only and no

coverage is provided for cosmec defects.

• Signal issues related to Wi-Fi connecvity are not covered by these warranes.

For parts and service assistance, or to nd Marvel factory authorized service near you, contact Marvel Refrigeraon:

MarvelRefrigeraon.com • techsupport@MarvelRefrigeraon.com • +616.754.5601

1260 E. Van Deinse St., Greenville, MI 48838

All specications and product designs subject to change without notice. Such revisions do not entitle

the buyer to corresponding changes, improvements, additions, replacements or compensation for

previously purchased products.

www.marvelrefrigeration.com

1260 E. Van Deinse St.

Greenville MI 48838

800.223.3900

41013836-EN Rev L

1/14/20

Marvel Refrigeration

Beverage center

Stockage de boissons

ML24BCG0

EN Installation, Operation and Maintenance Instructions

FR Instructions d’installation, d’utilisation et d’entretien

CONTENU

Contenu :

Informations de sécurité.......................................................2

Déballage de votre appareil ..................................................3

Enregistrement de la garantie .......................................3

Installation de votre appareil ..............................................4

Dégagements par rapport à l’armoire .............................4

Mise à niveau de l’appareil .............................................4

Raccordement électrique.................................................5

Dimensions du produit.........................................................6

Utilisation de votre commande électronique ......................8

Démarrage de votre appareil .........................................8

Mise en marche et arrêt de votre appareil ......................8

Réglage de la température .............................................8

Alertes............................................................................8

Congurations de étagères ................................................9

Entretien et nettoyage .......................................................10

Conseils pour l’économie d’énergie .................................10

Obtention de service ..........................................................11

Dépannage................................................................12

Garantie...........................................................................13

REMARQUE

ATTENTION

AVERTISSEMENT - Risque possible de décès ou

de blessure grave si vous ne suivez pas les instructions.

AVERTISSEMENT

Importantes instructions de sécurité

Les avertissements et les instructions de sécurité qui ap-

paraissent dans ce guide n’ont pas la prétention de couvrir

toutes les conditions et situations possibles pouvant arriver.

Il faut faire preuve de bon sens, de précautions et de soins,

pour installer, utiliser ou entretenir cet appareil.

Reconnaissance des symboles,

des mots et des étiquettes

concernant la sécurité.

ATTENTION - Risques ou pratiques dangereuses

pouvant entraîner des blessures individuelles, des dégâts

matériels ou des dommages au produit.

REMARQUE - Information importante pour réaliser une

installation et une utilisation sans problèmes.

Avertissements de la proposition 65 de l'État de Californie

: Ce produit contient au moins un produit chimique connu par

l’État de Californie pour être à l’origine de cancers.

AVERTISSEMENT

Avertissements de la proposition 65 de l'État de Californie

: Ce produit contient au moins un produit chimique connu par

l’État de Californie pour être à l’origine de malformations et

autres déciences de naissance.

AVERTISSEMENT

DÉBALLAGE DE VOTRE APPAREIL

XXXXXXXXXXXX

AVERTISSEMENT

ATTENTION

REMARQUE

Enregistrement de la garantie

Il est important que vous postiez votre carte de garantie

immédiatement après avoir pris livraison de votre appareil.

Les informations suivantes

seront nécessaires au mo-

ment de l’enregistrement

de votre appareil :

Numéro de service

Numéro de série

Date d’achat

Nom et adresse du revendeur

Le numéro de service et le numéro de série se trouvent sur la

plaque signalétique qui est située à l’intérieur de l’armoire, du

côté gauche près du haut (Voyez la Figure 1).

AVERTISSEMENT

RISQUE DE POIDS EXCESSIF

Utilisez deux personnes ou plus pour déplacer le produit.

Sinon vous pourriez vous blesser.

Enlèvement de l’emballage intérieur

Votre appareil a été emballé pour l’expédition avec toutes les

pièces pouvant être endommagées par le mouvement solidement

attachées. Enlevez les matériaux d’emballage intérieur et toute

bande maintenant des composants intérieurs en place. Le manuel

de l’utilisateur est envoyé à l’intérieur de l’appareil dans un sac en

plastique, accompagné de la carte d’enregistrement de la garan-

tie, et d’autres articles accessoires.

Important

Conservez votre carton d’emballage jusqu'à ce que votre appareil

ait été complètement inspecté et trouvé en bon état. S’il présentait

des dommages, cet emballage serait nécessaire comme preuve

qu’ils sont survenus durant le transit. Ensuite veuillez mettre tous

ces matériaux d’emballage au rebut d’une façon responsable.

Note pour le client

Cette marchandise a été soigneusement et complètement inspec-

tée avant de quitter notre usine. La responsabilité pour sa livrai-

son sûre a été assumée par le revendeur à l’acceptation de cette

expédition. Les réclamations pour perte ou dommages survenus

durant le transit sont à adresser au revendeur.

NE RENVOYEZ PAS DE MARCHANDISE ENDOMMA-

GÉE AU FABRICANT – DÉPOSEZ UNE RÉCLAMATION

AUPRÈS DU REVENDEUR.

Si l’appareil a été livré, manipulé ou entreposé dans une posi-

tion autre que debout, pendant une durée quelconque, laissez-le

reposer debout pendant au moins 24 heures avant de la brancher

électriquement. Cela assurera le retour de l’huile au compresseur.

Un branchement immédiat de l’appareil pourrait endommager des

parties internes.

Figure 1

Enregistrement

en ligne disponible

sur

www.marvelrefrigeration.

com

AVERTISSEMENT - Jetez bien les sacs en plastique qui

représentent un risque de suffocation.

AVERTISSEMENT

AVERTISSEMENT - Contribuez à éviter des tragédies

L’emprisonnement d’enfants et leur asphyxie ne sont pas

des problèmes du passé. Des épaves de réfrigérateurs

abandonnés continuent de présenter un danger - même

en restant dehors pour «juste quelques heures».

Si vous devez vous débarrasser de votre vieil appareil

de refroidissement, veuillez suivre ces instructions pour

aider à éviter des accidents possibles.

Avant de jeter votre vieux réfrigérateur ou congélateur :

• Démontez ses portes ou enlevez ses tiroirs.

• Laissez les étagères en place de façon à ce que des

enfants ne puissent pas facilement monter dedans.

AVERTISSEMENT

MARVEL

Figure 2

INSTALLATION DE VOTRE APPAREIL

AVERTISSEMENT

ATTENTION

Un kit optionnel d’empilage est nécessaire pour empiler des

produits. Le fait de ne pas utiliser de kit d’empilage peut

entraîner une blessure corporelle. Contactez votre revendeur

ou le service à la clientèle de Marvel au 800-223-3900 pour le

commander.

Choix de l’emplacement

Un bon emplacement assurera une performance de pointe pour

votre appareil. Nous recommandons un endroit où l’appareil ne

sera pas exposé directement au rayonnement solaire et restera

écarté de sources de chauffage. Pour assurer que les perfor-

mances de votre produit soient au niveau de ses spécications, la

plage de températures recommandée au lieu d’installation sera de

55 à 100°F (13 à 38 °C).

Dégagements par rapport à l’armoire

Une ventilation est nécessaire depuis la section frontale du bas de

l’armoire. Gardez cette zone libre et exempte de toutes obstruc-

tions. Des meubles et comptoirs peuvent être installés autour de

l’unité de façon adjacente dans la mesure où sa grille frontale

restera non obstruée.

Grille frontale

N’obstruez pas la grille frontale. Les ouvertures au travers de la

grille frontale permettent l’écoulement de l’air par l’échangeur

thermique du condenseur. Des restrictions de ce ux d’air vont

augmenter la consommation d’énergie et affecter sa capacité de

refroidissement. C’est pourquoi il est important que cette zone ne

soit pas obstruée et soit maintenue propre. Marvel recommande

de ne pas utiliser de grilles personnalisées, car l’écoulement d’air

en serait diminué (Voyez la Figure 2).

Pieds de mise à

niveau avant

Pieds de

mise à niveau

arrière

Grille frontale,

gardez cette

zone dégagée.

Pieds de mise à niveau

Des pieds réglables aux angles avant et arrière de l’armoire doi-

vent être ajustés pour qu’elle soit fermement positionnée au sol et

bien d’aplomb, d’un côté à l’autre et d’avant en arrière. La hauteur

totale de votre appareil Marvel peut être ajustée entre le minimum

⁄4 po (85,7 cm) (en vissant les pieds de mise à niveau CW ↷) et

le maximum 34

⁄4 po (88,3 cm) (en dévissant les pieds de mise à

niveau CCW ↶) des.

Pour régler ces pieds de mise à niveau, placez l’appareil sur une

surface solide, en protégeant le sol en dessous pour ne pas le

rayer. Avec l’aide d’une autre personne, inclinez vers l’arrière de

l’appareil pour accéder aux pieds de mise à niveau de l’avant.

Levez ou abaissez ces pieds à la hauteur requise en les tournant.

Répétez la procédure pour les pieds arrière en inclinant le cave à

vin vers l’avant en faisant attention. Sur une surface plane, véri-

ez le niveau de l’appareil et ajustez les pieds en conséquence.

Les vis de la grille frontale peuvent être desserrées et la grille

ajustée à la hauteur voulue. Quand le réglage est fait resserrez

les vis de la grille frontale (Voyez la Figure 5).

Figure 3

Figure 4

Figure 5

INSTALLATION DE VOTRE APPAREIL

N’enlevez pas la

borne de terre de

la che du cordon

secteur.

Vis de grille

frontale

Grille frontale

Figure 6

REMARQUE

Risque de commotion électrique

• N’utilisez pas de rallonge secteur avec cet appareil. Cela

peut être dangereux et peut affecter la performance du

produit.

• Cet appareil ne doit sous aucun prétexte être installé sur

une alimentation électrique sans liaison de terre.

• N’enlevez pas la borne de terre de la che du cordon

secteur. (Voyez la Figure 3).

• N’utilisez pas d’adaptateur entre che et prise. (Voyez la

Figure 4).

• N’envoyez pas d’eau par éclaboussure ou par jet d’un

tuyau sur l’appareil. Cela pourrait causer une commo-

tion électrique, entraînant potentiellement des blessures

graves voire mortelles.

Raccordement électrique

Un circuit secteur dédié en 115 V supportant 15 A est nécessaire.

Ce produit est équipé en usine d’un cordon secteur comportant

une che avec terre à trois broches. Il faut la brancher dans une

prise secteur correspondante avec terre, en conformité avec la

norme électrique américaine et les normes et réglementations

locales applicables (Voyez la Figure 6). Si le circuit ne comporte

pas une prise avec terre, le client doit en fournir une adéquate;

c’est sa responsabilité et son obligation. La troisième broche de

terre ne doit en aucun cas être coupée ou enlevée.

Un disjoncteur sur détection de courant de fuite (GFCI) a ten-

dance à provoquer des déclenchements intempestifs qui peuvent

arrêter l’appareil. Ce type de protection n’est en général pas

utilisé sur de l’équipement électrique qui doit tourner sans surveil-

lance pendant de longues périodes, sauf si c’est imposé par les

normes de construction et réglementations locales.

AVERTISSEMENT

DIMENSIONS D’OUVERTURE BRUTE DIMENSIONS D’ARMOIRE

MODÈLE «A» «B» «C» «D» «E» «F» «G» «H» «J»

ML24BCG0

24 po

(61 cm)

**34 po à 35 po

(86,4 à 88,9 cm)

⁄8 po

(60,7 cm)

⁄4 po à 34

⁄4 po

(85,7 à 88,3 cm)

⁄32 po

(60,2 cm)

⁄32 po

(65,2 cm)

⁄32 po

(117,9 cm)

⁄16 po

(65,2 cm)

«A»

«B»

«C»

«D»

«E»

Figure 7

Figure 7a

Figure 8

DIMENSIONS DU PRODUIT

S’il est nécessaire de gagner du dégagement à l’intérieur de

l’ouverture brute, un trou peut être percé au travers du meuble

adjacent et le cordon d’alimentation passé par ce trou jusqu’à

une prise secteur. Une autre façon d'augmenter la profondeur

disponible dans l’ouverture est d’encastrer la prise secteur dans

le mur arrière an de gagner l’épaisseur de la che du cordon.

Tous les types de prises secteur encastrées ne fonctionneront

pas pour cette application car elles pourraient être trop étroites,

mais un modèle équivalent à l’Arlington #DVFR1W est recom-

mandé pour cette application (Voyez la Figure 8).

La page charge ...

Marvel 30ARM-BS-F-R Mode d'emploi

Marque: Marvel

Modèle: 30ARM-BS-F-R

Catégorie: Boissons glacées

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Marvel 30ARM-BS-F-R User guide

Marvel 30ARM-BS-F-R Mode d'emploi

Marvel 30ARM-BS-F-R Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents