GE GFW850SSNWW Le manuel du propriétaire

WASHERS

OWNER’S MANUAL &

INSTALLATION

INSTRUCTIONS

Write the model number, serial

number and MAC ID for WiFi

enabled models here:

Model # _________________

Serial # _________________

MAC ID _________________

You can find them on a label

inside the washer door.

GE is a trademark of the General Electric Company. Manufactured under trademark license.

49-3000368 Rev 0 11-23 GEA

SAFETY INFORMATION ...........3

USING THE WASHER

Getting Started ...................... 5

Appliance Communication .............14

Dryer Control ........................15

Dispensers ...........................16

Consumer Help Indicator ..............18

Loading .............................19

CARE AND CLEANING ...........20

INSTALLATION

INSTRUCTIONS ....................22

Reversing The Door Swing (optional on

some models only) .....................27

TROUBLESHOOTING TIPS ......31

LIMITED WARRANTY ............35

CONSUMER SUPPORT .......... 36

QUICK REFERENCE GUIDE ..... 37

QUICK INSTALLATION GUIDE .. 38

PFW950

PFW870

GFW850

GFW655

GFW650

GFW550

GFW510

ENGLISH/FRANÇAIS/

ESPAÑOL

249-3000368 Rev 0

THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.

Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.

We take pride in the craftsmanship, innovation and design that goes into every GE Appliances

product, and we think you will too. Among other things, registration of your appliance ensures that we

can deliver important product information and warranty details when you need them.

Register your GE appliance now online. Helpful websites and phone numbers are available in the

Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration

card included in the packing material.

49-3000368 Rev 0 3

READ AND SAVE THESE INSTRUCTIONS

To reduce the risk of death, fire, explosion, electric shock, or injury to persons when using

your appliance, follow basic precautions, including the following:

Ŷ Read all instructions before using the appliance.

Ŷ Follow all fabric care instructions and warnings to prevent melting of garments or damage to the appliance.

Ŷ DO NOT wash or dry articles that have been previously cleaned in, washed in, soaked in or spotted with

gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could

ignite or explode.

Ŷ DO NOT add gasoline, dry-cleaning solvents, or other flammable or explosive substances to the wash water.

These substances give off vapors that could ignite or explode.

Ŷ Under certain conditions, hydrogen gas may be produced in a hot-water system that has not been used for

2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a

period, before using a washing machine, turn on all hot-water faucets and let the water flow from each for

several minutes. This will release any accumulated hydrogen gas. As the gas is flammable, DO NOT smoke

or use an open flame during this time.

Ŷ DO NOT allow children to play on or in this appliance. Close supervision of children is necessary when this

appliance is used near children. Before the washer is removed from service or discarded, remove the door or

lid. Failure to follow these instructions may result in death or injury to persons.

Ŷ DO NOT reach into the appliance if the tub or agitator is moving to prevent accidental entanglement.

Ŷ DO NOT install or store this appliance where it will be exposed to the weather.

Ŷ DO NOT tamper with controls, repair or replace any part of this appliance or attempt any servicing unless

specifically recommended in the user maintenance instructions or in published user repair instructions that you

understand and have the skills to carry out.

Ŷ DO NOT climb or stand on this unit.

Ŷ DO NOT operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or

broken parts including a damaged cord or plug.

Ŷ Unplug the appliance or turn off the circuit breaker before servicing. Pressing the Power pad DOES NOT

disconnect power.

Ŷ See “ELECTRICAL REQUIREMENTS” located in the Installation Instructions for grounding instructions.

Ŷ DO NOT use replacement parts that have not been recommended by the manufacturer. (e.g. parts made at

home using a 3D printer).

WARNING

Proper Disposal of your Appliance

Ŷ

Dispose of or recycle your appliance in accordance with Federal and Local Regulations. Contact your local

authorities for the environmentally safe disposal or recycling of your appliance.

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

SAFETY INFORMATION

449-3000368 Rev 0

SAFETY INFORMATION

READ AND SAVE THESE INSTRUCTIONS

PROPER INSTALLATION

This washer must be properly installed and located in accordance with the Installation Instructions before it is used.

Ŷ Ensure that the hot water hose is connected to the “H” valve and the cold water hose is connected to the “C”

valve.

Ŷ Install or store where it will not be exposed to temperatures below freezing or exposed to the weather, which

could cause permanent damage and invalidate the warranty.

Ŷ Properly ground washer to conform with all governing codes and ordinances. Follow details in the Installation

Instructions.

Ŷ Ensure washer is properly leveled and washer legs are adjusted such that unit is stable.

Ŷ

Optional drain hose extension recommended for discharging heights from 60” - 96”.

Ŷ GE Appliances strongly recommends the use of factory specified parts. A list of factory hoses available for

purchase are listed. These hoses are manufactured and tested to meet GE Appliances specifications.

Ŷ GE Appliances strongly recommends the use of new water supply hoses. Hoses degrade over time and need

to be replaced every 5 years to reduce the risk of hose failures and water damage.

Ŷ Consider recycling options for your appliance packaging material.

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

PARTS AND ACCESSORIES

Order on-line at GEApplianceparts.com today,

24 hours a day or by phone at 877.959.8688 during

normal business hours. In Canada, visit your local

GE Appliances parts distributor or call 800.661.1616

or

GEAppliances.ca/en/products/parts-filters-accessories.

Part Number Accessory

WX14X10011 6 ft stainless steel washer hoses with

90° elbows; 2-pack

WH49X316 Washer drain hose extension kit -

Approximately 44”

WX10X10011 Tide® Washing Machine Cleaner*

PM7X2 Universal low profile washer floor tray

GFA28KITN Stack Bracket Kit (to stack dryer on top)

GFP1528S 28” width Pedestal with drawer – White

GFP1528P 28” width Pedestal with drawer – Colors

GFR0728S 28” width Riser without drawer – White

GFR0728P 28” width Riser without drawer – Colors

*Tide® is a registered trademark of Procter & Gamble

WHEN NOT IN USE

Ŷ Turn off water faucets to minimize leakage if a break or rupture should occur. Check the condition of the fill

hoses; GE Appliances recommends changing the hoses every 5 years.

AUTOMATIC DRAIN SEQUENCE

Ŷ Machine will automatically drain any time the door is left open for more than 15 minutes and water is present.

Ŷ Machine will automatically drain if left in a paused state with the door closed for more than 24 hours and water

is present.

49-3000368 Rev 0 5

USING THE WASHER

Throughout this manual, features and appearance may vary from your model.

Step 4 Step 5Step 1

To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY

INFORMATION before operating this appliance.

WARNING

(cycle options

vary by model)

Load clothes into your

washer and close the

door.

If the screen is dark,

press the Power pad or

turn the knob to “wake

up” the display.

Turn the knob to

select the desired

cycle.

Open the dispenser and add

detergent, bleach and fabric

softener, as desired. Models

with SmartDispense™ only

require that you select the

SmartDispense pad once the

tank has been filled.

Press Start to begin the

wash cycle. The machine

will weigh your clothes and

add the proper amount of

water. When the wash cycle

is finished, the door will

unlock.

Step 2

Step 3

Quick Start:

Display and Status Lights

(Features and appearance will vary)

On some models, the display shows the approximate time remaining until the end of the cycle and the washer cycle

status (Prewash, Fill, Wash, Rinse and Spin).

NOTE: The cycle time is affected by how long it takes the washer to fill. This depends on the water pressure in your

home. The “smart” timer “learns” the amount of time it takes to fill your washer and adjusts the total time accordingly.

On some models, if an out-of-balance condition is detected by the washer, the Spin status light or Spin option selection

light will blink during the remaining portion of the cycle and will stay illuminated for a short time after cycle completion.

When this occurs, the washer is taking actions to correct the out-of-balance condition and complete the cycle normally.

In some cases, the washer may not be able to balance the load and spin up to full speed. If you notice the load is more

wet than usual at the end of the cycle, redistribute the load evenly in the wash tub and run a Rinse & Spin cycle.

In addition, the display will show:

(WiFi)

(on some models)

Will allow your appliance to communicate with your smartphone for remote appliance monitoring,

control and notifications. It stays lit whenever the washer is on and is connected. It will blink during the

commissioning process or if it loses connection to the network.

Venting

(on some models) Venting will blink to indicate that you can select the ULTRAFRESH VENT feature at the end of the cycle.

It then stays illuminated once selected until venting is complete.

Control The controls on the washer are locked when this icon is illuminated. You must press and hold the Control

Lock pad to unlock the controls.

Door This icon will illuminate while the door is locked and will blink while the washer is in the process of pausing

and then unlocking.

Smart This icon will illuminate when the Smart AI features of your washer are active.

Auto, More, Less

(on some models) The SmartDispense will automatically dose detergent according to the weight and soil level of the clothes. You

can adjust this feature to dose MORE or LESS detergent or turn it OFF to manually dose detergent.

Tank Low

(on some models) At start up the unit displays when the SmartDispense tank needs to be re-filled. Typically, this first lights up when

there are approximately 8 - 10 loads of detergent remaining.

Loads Left

(on some models) Displays the estimated number of wash loads left for the amount of detergent in the SmartDispense tank.

Delay

(on some models) When you select a delay start to your wash, this will be indicated by either a light next to the pad or with the word

“Delay” in the center of the options window. The display will also countdown the hours until the cycle begins.

Using the washer

Step 6 (on some models)

After the wash cycle

is completed and the

clothes unloaded, select

ULTRAFRESH VENT™ to

help eliminate the excess

moisture in your washer so

you can close the door.

649-3000368 Rev 0

Getting started

USING THE WASHER

Features and appearance will vary.

CA

B E ED

Model:

PFW870

CA

B E ED

Model:

PFW950

CA

B E ED

Model:

GFW850

CA

B E ED

Model:

GFW655

CA

B E ED

Model:

GFW650

49-3000368 Rev 0 7

USING THE WASHER

Getting started

Features and appearance will vary.

CA

B E ED

Model:

GFW550

CA

B E ED

Model:

GFW510SC

CA

B E ED

Model:

GFW510SS

849-3000368 Rev 0

Using the washer

USING THE WASHER

A

B

C

Power

Press to “wake up” the display. If the display is active, press to put the washer into standby “OFF” mode.

NOTE: Pressing Power does not disconnect the appliance from the power supply.

Start and Pause (Add Garment)

Press to start a wash cycle. If the washer is running, pressing it once will pause the washer and unlock the door,

allowing Add Garment (should be done early in the wash cycle) or removal of a garment. It will take a few

seconds for the door to unlock after pressing Start/Pause. After adding or removing garments, press again to

restart the wash cycle.

NOTE: If washer is paused and cycle is not restarted within 15 minutes, the current wash cycle will be cancelled.

NOTE: The washer performs automatic system checks after pressing the Start pad. Water will flow in 45

seconds or less. You may hear the door lock and unlock and the pump activate before water flows.

Wash Cycles

The cycles are optimized for specific types of loads. The chart below will help you match the items to be

laundered with the best cycle settings. For optimal performance, select the cycle that most closely matches the

items in your load. Delay Start/Remote Start is available on all cycles.

Cycle Recommended Items

Normal Cycle for normal, regular, or typical use for washing up to a full load of normally soiled cotton clothing.

Delicates Lingerie and special care fabrics with light soil.

Towels Towels, sheets, pillowcases and dish rags.

Bulky Bedding Comforters, large coats, bed spreads, mattress covers, sleeping bags, and similar large bulky

items.

Sanitize+

Allergen*

Heavily soiled colorfast items with the need for sanitization.

Sanitize With

Oxi*

Heavily soiled colorfast items with the need for sanitization.

Active Wear Medium to lightly soiled athletic wear items of technical or synthetic fabrics.

Quick Wash Small loads of lightly soiled items that are needed in a hurry.

Whites Whites and household linens.

Rinse and Spin For items that need only to be rinsed and not washed. Rinse & Spin, or Drain & Spin (Extra

Rinse deselected). A spin is always performed unless you select No Spin.

Cold Wash Cycle for normal, regular, or typical use for washing up to a full load of normally soiled cotton

clothing using only cold water while delivering equivalent performance to Normal Warm wash.

Downloaded Use the SmartHQ App to download a specialty cycle for your washer.

Power Clean For heavily soiled items which require extra cleaning power.

Heavy Duty* For washing heavily soiled, sturdy colorfast items using extended wash motions and rinses to

deliver extra cleaning.

Jeans Jeans with medium to light soil.

Swim Wear Swim wear with medium to light soil.

Self Clean Cleaning the basket of residue and odor. No clothes are to be washed using this cycle.

*Some cycles and options may not be available on some models.

NOTES:

The SANITIZE + Allergen cycle’s water temperatures CANNOT be changed. This cycle utilizes elevated water

temperature and a longer wash cycle to kill dust mites and reduce 99% of common bacteria from fabrics. A pump

purge and extended rinse is incorporated for the purpose of removing contaminants and allergens, such as pet dander.

The SANITIZE With Oxi cycle’s water temperatures CANNOT be changed. This cycle, when using an Oxi additive

along with your detergent, is designed to remove 99% of bacteria found in home laundry. Measure the detergent and

the Oxi products carefully. Using the amounts appropriate for a large heavily soiled load in a front load washer, follow

the detergent and the Oxi product label instructions. The washer hot water supply connection must provide a minimum

of 120°F to ensure the effectiveness of this cycle.

Only the SANITIZE + Allergen and SANITIZE With Oxi cycles have been designed to meet the requirements of

sanitizing effectiveness.

49-3000368 Rev 0 9

USING THE WASHER

Using the washer

Wash Cycles - Continued

The cycles are optimized for specific types of loads. The chart below will help you match the items to be

laundered with the best cycle settings. For optimal performance, select the cycle that most closely matches the

items in your load. Delay Start/Remote Start is available on all cycles.

C

Wash Cycles

Normal

Delicates

Towels

Bulky Items

Active Wear

Quick Wash

Whites

Rinse and Spin

Cold Wash

Heavy Duty*

Jeans*

Swim Wear*

Sanitize with

Oxi*

Sanitize+

Allergen*

Power Clean

Self Clean

Wash Settings

Soil Level

This cycle is for periodic cleaning of the washer only.

See the Self Clean section for more information.

Extra Heavy • ••• • • ••• • • •

Heavy • • • • • • • • • • • •

Normal ••••••• • ••• •

Light • •••••• • •••

Extra Light ••••••• • ••

Wash Temperature

Extra Hot •• •••

Hot • • • • • • • •

Warm ••••••• ••• •

Cold • •••••• • ••• •

Tap Cold ••••••• • ••• •

Spin Selection

Max • •• •••••• • • •

High • • • • • • • • • • • •

Medium • •••••• • • ••• • • •

Low •••••• • • •• • • •

No Spin •• • •

Wash Options

Power Steam* ••• • •• ••

Prewash* or Auto Soak* ••••• • • ••• • • •

Time Saver ••••• •

More Water • • • • • • • • • •

Extra Rinse • •••••• • • ••• • • •

Tumble Care* • •••••• • • • • • •

Soak Rinse for Sanitizer ••••••• • • ••• • •

• Available setting Factory default setting

* Available from Downloaded cycles.

10 49-3000368 Rev 0

Using the washer

USING THE WASHER

DSettings

Individual settings for soil level (Level), water temperature (Temp) and spin speed (Spin) can be set from the

minimum to maximum. In general, the higher up the column, the more energy will be used.

Soil

Changing the Soil level increases or decreases the wash time to remove different amounts of soil.

To change the Soil level, press the Soil level pad until you have reached the desired setting. You can choose

between Extra Light, Light, Normal, Heavy or Extra Heavy soil levels on most cycles.

Temp

Adjust to select the proper water temperature for the wash cycle. The AutoSoak and PreWash rinse water is

always cold to help reduce energy usage and reduce setting of stains and wrinkles.

Follow the fabric manufacturer’s care label when selecting the wash temperature.

To change the wash temperature, press the Temp pad until you have reached the desired setting. You can

choose between Tap Cold, Cold, Warm, Hot or Extra Hot on most cycles. By design, to protect fabrics, not all

wash temperatures are available for certain wash cycles. Extra Hot temperatures are enabled by the internal

heater on models equipped with Steam capabilities.

NOTE: The first 10 seconds of the wash fill is always cold. This feature assists in conditioning the fabric and

preventing stains from setting on garments.

Spin

Adjusting the Spin speed changes the final spin speed of the cycles. Always follow the garment manufacturer’s

care label when changing the Spin speed.

To change the Spin speed, press the Spin speed pad until you have reached the desired setting. You can

choose between No Spin, Low, Medium, High or Max. Higher spin speeds are not available on certain cycles,

such as DELICATES and ACTIVE WEAR.

Higher spin speeds remove more water from the clothes and will help reduce dry time, but may also increase

the possibility of setting wrinkles on some fabrics.

NOTE: This washer features a dBT™ (Dynamic Balancing Technology) system. This patented onboard

sensing technology enables real-time balancing of the spin cycle for each load, saving time and providing a

quiet wash. This should lead to more consistent wash times and an overall reduction in noise and vibration.

If the washer should experience any excessive noise, vibration or shaking, simply Pause the washer, open the

door, and manually redistribute the load before restarting the cycle.

EOptions

SMARTDISPENSE™ (on some models)

When selected, this feature will automatically add detergent to the wash, eliminating the need to add detergent

for each load. See the SmartDispense section for details.

My Settings (on some models)

To save your favorite settings for a given cycle, set the desired options for Soil, Spin and Temp levels, extra

rinse and other settings. Hold down the My Settings pad for 3 seconds. A beep will sound to indicate the

selections for this cycle have been saved. You can choose to create My Settings for other cycles.

STEAM/POWER STEAM (on some models)

The steam feature adds steam into the washer before the wash cycle begins to assist with loosening stains on

the NORMAL, WHITES, TOWELS, BULKY Bedding, SANITIZE+Allergen and POWER CLEAN cycles.

To use:

1. Press the Power pad to “wake up” the washer and select a wash cycle.

2. Use the SmartHQ App or press the POWER STEAM pad (on some models) to activate steam.

3. Press the Start/Pause pad.

WiFi (may be a shared pad with other options)

Press and hold the WiFi* pad for 3 seconds to activate. See the WiFi Connect section for details on how to

get stated with WiFi connection.

49-3000368 Rev 0 11

USING THE WASHER

Using the washer

EOptions

Delay Wash/Remote Start

You can delay the start of a wash cycle for up to 24 hours or remote start the washer by using the Delay Wash/

Remote Start feature. Press to step by hours or hold to scroll the Delay Wash pad to set the amount of time

you want to delay the start of the wash cycle. If you have connected your washer to WiFi, the first selection,

“AP”, can be selected to enable remote starting of your washer from the GE Appliance Smartphone app. Or,

if you select a delay time in hours, the machine will count down and start automatically following this period.

Press the Start pad once you have configured the Delay Wash to the proper setting to enable this feature. To

cancel this option, simply power off and power on the controls.

NOTE: If you forget to fully close the door, a reminder signal will beep reminding you to do so.

NOTE: If you open the door when the delay is counting down, the machine will enter the pause state. You must

close the door and press Start again in order to restart the countdown.

Time Saver (on some models)

This option reduces the overall washer cycle time by optimizing the wash, rinse and spin actions and/or

gently raising the wash temperature to get clothes cleaned faster. Option is available on NORMAL, WHITES,

TOWELS, DELICATES, BULKY Bedding and ACTIVE WEAR cycles. Total wash time will vary based on

cycle chosen and options selected.

To use:

1. Turn power on and select a wash cycle which has Time Saver as an option.

2. Press the Time Saver pad to reduce the overall wash time.

3. Press the Start/Pause pad.

More Water (on some models)

This option adds approximately 3 gallons to the wash and rinse portions of the cycle. If the option is selected

before the cycle starts, the water will be added from the beginning of the wash cycle and later to the rinse. If

the option is selected during the wash portion, more water will be added at this point and later to the rinse.

Likewise, if the More Water option is selected after the wash portion has completed, the washer will add more

water to the rinse only. If wash and rinse have completed, the More Water pad will no longer be active.

ULTRAFRESH VENT System with ODORBLOCK™ (on GE Appliances and Profile models only)

The ULTRAFRESH VENT System with OdorBlock was designed to eliminate excess moisture in the washer

following a wash cycle to help prevent odors from developing. This washer was designed to drain water at the

end of the cycle more effectively. Following the wash cycle, the user can then choose to leave the door open

or select the ULTRAFRESH VENT feature to assist with drying out the gasket and other areas of the washer.

The OdorBlock system features multiple components which are manufactured with Microban® antimicrobial

technology.* Microban is a safe and effective antimicrobial technology that will last the life of your washer. For

more information, please visit www.microban.com/geappliances.

ULTRAFRESH VENT is available after the wash cycle is complete and you have removed your cleaned

laundry. Once the door is closed, a notification tune will play and the ULTRAFRESH VENT pad LED will blink.

Upon pressing the pad, ULTRAFRESH VENT will begin.

To select ULTRAFRESH VENT at any other point, power on the washer, ensure a cycle is

not actively running, and remove any garments from the basket, then press and release the

ULTRAFRESH VENT pad so that the notification tune plays and the ULTRAFRESH VENT pad

LED begins to blink. Then press the ULTRAFRESH VENT pad again to start the feature.

During the operation of ULTRAFRESH VENT the door will remain locked and the washer will intermittently spin

at low speeds for up to 8 hours. Profile models utilize a sensor to determine end time.

If garments are detected in the basket during ULTRAFRESH VENT, the washer will instead run TUMBLE

CARE or 1 STEP WASH + DRY, based on option availability for your model.

The ULTRAFRESH VENT feature may be cancelled at any time by pressing the POWER pad, turning the cycle

knob, or pressing the ULTRAFRESH VENT pad.

12 49-3000368 Rev 0

Using the washer

USING THE WASHER

EOptions

SmartHQ App Enabled

There are several options that support your WiFi connected washer available through the SmartHQ

App. Not only does this App enable you to receive over the air upgrades and updates to your

washers software, but it unlocks special features for your washer. Among those features are

Adaptive SmartDispense, Adaptive My Settings and Stain Removal Guide.

*Microban® is a registered trademark of Microban International, Ltd.

1 STEP WASH + DRY (on some models)

This option is available on all cycles except Self Clean.

The 1 STEP WASH + DRY is intended for small loads only. Use when clothes need to be washed, dried and

ready to wear or finished the next morning. This feature will tumble clothes and introduce a constant stream of

air into the washer compartment upon completion of select wash cycles. Although the drying portion is set to 8

hours, the clothes can be removed at any time by pressing Pause or Power to cancel the cycle.

Tumble Care (on some models)

Freshly tumbles your garments periodically for up to 8 hours after the wash cycle is complete to lessen the

setting of wrinkles and creases when you are not able to move clothing to the dryer right away.

At the end of the cycle, the display will scroll “END” and after ten minutes the Tumble Care will begin. It can be

stopped at any time by pressing the Power pad.

PreWash (on some models)

Prewash is an extra wash before the main wash. Use it for heavily soiled clothes or for clothes with a care label

that recommends prewashing before washing. Be sure to add liquid or powder high-efficiency detergent, or the

proper wash additive to the prewash dispenser. Washers equipped with SmartDispense will automatically add

the proper amount of detergent for prewash based on the load size.

PreWash must be selected prior to pressing Start.

The PreWash feature will fill the washer (adding the prewash detergent), tumble the clothes, drain and spin.

Then the washer will run the selected wash cycle.

NOTE: In some special cycles, the prewash is selected automatically as the default. You can turn off this

selection at any time. The main wash will use new detergent from the manual detergent compartment and from

the SmartDispense tank (on some models).

AutoSoak (on some models)

For soaking your garments prior to the wash cycle. This option begins with a brief tumble and then proceeds to

soak the clothes with water and detergent for a specified period of time. Once complete, the cycle will continue

automatically. AutoSoak must be selected prior to pressing the start pad. The AutoSoak time will add an

additional 15 minutes, 30 minutes, 1 hour or 2 hours to the overall wash time. High-efficiency detergent from the

main wash compartment in the dispenser is used for the AutoSoak period and main wash cycle.

Soak Rinse (on some models)

Select this feature when laundry sanitizer is used. This feature is recommended for special case loads only, not

for typical use. Press Soak Rinse for Sanitizer button to enable. An additional chime will occur and the cycle

time will increase due to additional soaking time to activate the laundry sanitizer. To cancel the option, press the

Soak Rinse for Sanitizer button again. NOTE: Fill the fabric softener compartment in the dispenser drawer with

the recommended amount of laundry sanitizer.

Extra Rinse

This option allows for an extra rinse during a cycle to remove excess dirt and detergent from soiled loads.

Press the Extra Rinse pad to select.

NOTE: On RINSE & SPIN cycle, a drain and spin cycle can be achieved by pressing the Extra Rinse pad until

the LED is no longer illuminated.

49-3000368 Rev 0 13

USING THE WASHER

Using the washer

EOptions

Light (on some models)

The basket light will turn on and remain on for 5 minutes when the door opens, Start/Pause pad is pressed, or

by pressing the Light pad. The basket light can be turned off by pressing the Light pad.

Sound

To change the loudness of the end of cycle signal and the press pad volume, press the Sound pad as many

times as needed to reach the desired volume. On some models there are four sound levels including off, other

models have Off/On with press and hold function.

Control Lock (Light-Control Lock pad) (depending on model)

You can lock the controls to prevent any selections from being made. Or you can lock or unlock the controls

after you have started a cycle.

Children cannot accidentally start the washer by touching pads with this option selected.

To lock/unlock the washer, press and hold the Control Lock/Light-Control Lock pad for 3 seconds. A sound

is made to indicate the lock/unlock status. The control lock icon on the display will light up when it is on.

NOTE: The Power pad can still be used when the machine is locked.

14 49-3000368 Rev 0

APPLIANCE COMMUNICATION

Appliance Communication

WiFi Connect (For customers in the United States only - GE Appliances and Profile

models only)

Your washer is GE Appliances WiFi Connect enabled.

It is highly recommended that you connect your washer to WiFi to

download the latest software, receive periodic updates and benefit

from many of the extended features available through the SmartHQ

App. Many of the AI features for your washer require connection to

the SmartHQ App.

Visit geappliances.com/connect and enter your model number to

show you the proper steps to connect your appliance.

Take special note of your washer’s serial number and MAC ID address

on the front of this manual.

Please visit GEAppliances.com/connect to learn more about

connected appliance features, to learn what connected appliance

App’s will work with your smartphone.

WiFi Connectivity: For assistance with the appliance or the

ConnectPlus network connectivity, please call GE Appliances at

800.220.6899.

Scan here to get started.

WiFi Label Location

49-3000368 Rev 0 15

USING THE WASHER

Using the washer

Dryer Control – Bluetooth® Pairing

(on some models)

1. Power on both the washer and the dryer but do not start any

cycles.

2. Press and hold the Tumble Care button on the

washer for 5 seconds until the Bluetooth® LED ( )

starts to flash and you hear an audible tone.

3. Open and close the dryer door 3 times within 10 seconds to

make it discoverable to the washer.

4. The washer will attempt to discover the dryer, the Bluetooth®

icon will flash and both displays will blink “ - - - ”.

5. The Bluetooth® icon on the washer should illuminate solid

signifying that the machines are now paired. The display on

the washer will display “bt” once pairing is complete.

6. If the Bluetooth® units fail to pair, repeat above steps 1-5.

7. To unpair the machines, press and hold the Tumble

Care button for 10 seconds or open and close the

dryer door 3 times within 10 seconds.

Open and close

dryer door

3 times within

10 seconds

1. Power on the washer.

2. Press and hold the Dryer Control button on the

washer for 3 seconds to power on the dryer.

3. The dryer’s cycle selection will flash to display the

recommended sensor cycle that pairs to the last completed

washer cycle as the washer display reads “drY”.

4. To use this cycle, press the Dryer Control button to

start the dryer. The dryer can be paused by opening

its door or pressing the Dryer Control button. To restart

the dryer with its door closed, press the Dryer Control

button again.

5. To select Timed Dry instead of the sensor dry cycle, press the

Timed Dry button on the washer while the display says “drY”.

Repeated presses of this button will step through preset Timed

Dry times (default is 10 minutes).

6. Once you’ve selected the Timed Dry cycle’s duration,

press the Dryer Control button within 10 seconds to

start the dryer.

Washer

Dryer

NOTE: Your dryer’s control panel is fully

functional even when you are using Dryer

Control through the washer.

Powering off the washer will not power off

the dryer when a dry cycle is in progress.

Scan for

instruction

How to use the Dryer Control Feature (on some models)

Scan for

instruction

16 49-3000368 Rev 0

Dispenser Drawer

Slowly open the dispenser drawer by pulling it out until

it stops. After adding laundry products, slowly close the

dispenser drawer. Closing the drawer too quickly could

result in early dispensing of the bleach, fabric softener or

detergent.

You may see water in the detergent, bleach and fabric

softener compartments at the end of the cycle. This is a

result of the flushing/siphoning action and is part of the

normal operation of the washer.

Do NOT put detergent packets in the dispenser drawer.

NOTE: Use only liquid or powder HE detergents and

additives in the dispenser drawer. Laundry detergent

packets should only be added directly to the wash

basket following the manufacturer’s directions.

Using the washer

USING THE WASHER

Use only HE

High-Efficiency

detergent

SmartDispense™ (on some models)

When selected, this feature will automatically add

detergent to the wash, eliminating the need to add

detergent for each load.

The detergent amount selection on the control

panel will default to AUTO when first powering up

the washing machine. When AUTO is selected, the

amount of detergent needed for each laundry load will

automatically be determined based on the size of the

load the machine senses.

For AUTO, the washer will dispense approximately 1.5 oz

of detergent for an 8 lb normal load. For other loads,

it will adjust proportionally based on the size of load

and garment type. If you select LESS, the amount of

detergent will be reduced by 40%. This may be desired

for higher concentrate detergents or if you have very soft

water. For heavily soiled loads, you may want to select

MORE to add 40% more detergent than the AUTO level.

You can set the brand/type of detergent in the SmartHQ

App so that the washer can make adjustments based on

detergent manufacturers recommendations.

NOTE: Not all cycles will allow the use of the

SmartDispense feature. If the light is not illuminated and

pressing the SMART DISPENSE pad results in a beeping

tone, then SmartDispense is not allowed for the cycle

that has been selected. Detergent will need to be added

directly to the detergent compartment for these cycles.

If it is desired to manually add detergent for a

particular load:

1. Press the SMART DISPENSE pad on the control

panel until its light turns off which indicates the

SmartDispense feature has been turned off.

2. Set the flap in the detergent compartment to the

type of detergent to be used - Powder or Liquid.

See the Detergent Compartment section.

3. Add the desired amount of detergent into the

detergent compartment.

If the display indicates that the SmartDispense tank is

estimating there is insufficient detergent to wash a load,

the SmartDispense light will flash. The washer can still

run a cycle, but it suggested that you add detergent

in the manual detergent compartment or refill the

SmartDispense tank.

Use only HE

High-Efficiency

liquid detergent

Softener

Detergent

Flap Selector

Bleach

SmartDispense

Prewash Compartment (on some models)

Only use the prewash compartment if you are selecting

the PreWash cycle for heavily soiled clothes. Add measured

detergent or prewash additive to the back left prewash

compartment of the dispenser drawer.

• Detergent or prewash additive is flushed from the

dispenser in the PreWash (if selected).

• Detergent usage may need to be adjusted for water

temperature, water hardness, size and soil level of the

load. Avoid using too much detergent in your washer

as it can lead to over sudsing and detergent residue

being left on the clothes.

Softener

Detergent

Flap Selector

Bleach

Add PreWash to

this compartment

49-3000368 Rev 0 17

USING THE WASHER

Using the washer

Detergent Compartment

Only use high-efficiency detergent in this washer.

Do NOT fill high-efficiency detergent over the MAX

line. Use detergent manufacturer’s recommended

amount.

• Powder Detergent – Lift the flap up for powder

detergent. This must be done to dissolve and flush

detergent properly. Follow the detergent manufacturer’s

instructions when measuring the amount of powder

detergent to use.

• Liquid Detergent – Keep the flap down for liquid

detergent. This retains the liquid detergent until it

automatically flushes at the start of the wash cycle.

Follow the detergent manufacturer’s instructions when

measuring the amount of liquid detergent to use.

Detergent usage may need to be adjusted for water

temperature, water hardness, size and soil level of the

load. Avoid using too much detergent in your washer as

it can lead to oversudsing, detergent residue being left

on the clothes, and could extend wash times.

Do not put clumped detergent in the dispenser. Clumped

detergent can cause a leak.

Do NOT put detergent

packets in the dispenser

drawer.

Softener

Detergent

Flap Selector

Bleach

SmartDispense

Softener

Detergent

Flap Selector

Bleach

Add PreWash to

this compartment

On models with SmartDispense: On models without SmartDispense:

Liquid Bleach Compartment

If desired, measure out the recommended amount of

liquid bleach, not to exceed 1/3 cup (80 ml) and pour into

the compartment labeled “LIQUID BLEACH” marked

with this symbol .

It is recommended to use High-Efficiency (HE) bleach in

this front-load washer.

Do not exceed the maximum fill line. Overfilling can

cause early dispensing of the bleach which could result

in damaged clothes.

NOTE: Do not use powdered bleach or laundry

detergent/additive packets in the dispenser.

Fabric Softener Compartment

If desired, pour the recommended amount of liquid

fabric softener into the compartment labeled “FABRIC

SOFTENER”.

Use only liquid fabric softener in the dispenser.

Do not exceed the maximum fill line. Overfilling can

cause early dispensing of the fabric softener, which

could stain clothes.

NOTE: Do not pour fabric softener directly on the wash

load.

NOTE: The fabric softener compartment will be siphoned

in the final rinse of the wash cycle. This compartment

can also be used to accommodate other liquid rinse

aids such as sanitizers and fabric enhancing liquids.

The use of these other products must be certified by the

liquid manufacturer for safety in the use of a residential

washing machine and combination washer/dryer. Please

check carefully, as certain liquids may invalidate the

warranty on your Washer.

18 49-3000368 Rev 0

USING THE WASHER

Your washer is equipped with Consumer Help Indicator (CHI). CHI is our way to communicate a simple remedy

for some situations that you can perform without the need to call for service. The chart below describes the helpful

messages you may notice scrolling on your display when you return to start another load. These messages will

provide simple remedies you can quickly perform.

Spin light

blinking If an out-of-balance condition is detected by the washer, the Spin light will blink during the

remaining portion of the cycle and will stay illuminated for a short time after cycle completion.

When this occurs, the washer is taking actions to correct the out-of-balance condition and

complete the cycle normally. In some cases, the washer may not be able to balance the load

and spin up to full speed. If you notice the load is more wet than normal at the end of the cycle,

redistribute the load evenly in the wash basket and run a Drain & Spin cycle. (See Extra Rinse

in the Using the washer - Options section for details.)

“H2O SUPPLY”

(Water not

entering washer)

Check your house water supply. Did you forget to turn on one or both supply valves after

installation or coming back from vacation? As soon as the message starts to scroll, the washer

will initiate a 4 minute lock-out period. The washer controls won’t respond/change during this time.

After the 4 minutes, you can begin your cycle again. If you try to bypass the lock-out period by

unplugging the washer, the 4 minute timer will start over again.

“CAnCELEd”“CAnCELEd” may scroll on the display if the machine was paused for longer than 24 hours or if

the machine has stopped itself before the cycle completed due to certain errors. As soon as the

message starts to scroll, the washer will initiate a 4 minute lock-out period. The washer controls

won’t respond/change during this time. After the 4 minute period, you can begin your cycle again.

If you try to bypass the lock-out period by unplugging the washer, the 4 minute timer will start over

again. If the problem persists, call GE Appliances at 800.GE.CARES (800.432.2737) for service.

“door”“door” will be shown on the display if you try to start a cycle when the door is not fully closed.

“door” will also be shown on display if 3 cycles have been started without opening the door.

The washer will not start another cycle until the door is opened. In either circumstance, try opening

and closing the door, and then starting a new cycle. If the problem persists, call GE Appliances

at 800.GE.CARES (800.432.2737) for service.

Consumer Help Indicator

49-3000368 Rev 0 19

USING THE WASHER

Loading

Always follow fabric manufacturer’s care label when laundering.

Sorting Wash Loads

Sort by color (whites, lights, colors), soil level, fabric type (sturdy cottons, easy care, delicates) and whether the

fabric produces lint (terry cloth, chenille) or collects lint (velveteen, corduroy). Wash lint producers such as cotton

towels and socks separate from lint collectors including synthetic garments and dress pants.

Loading the Washer

The wash drum may be fully loaded with loosely added items.

To add items after the washer has started, press Start/Pause and wait until the door is unlatched. The washer may

take up to 30 seconds to unlock the door after pressing Start/Pause, depending on the machine conditions. Do not

try to force open the door when it is locked. After the door unlocks, open gently. Add items, close the door and press

Start/Pause to restart.

DO NOT wash fabrics soiled with flammable liquids or cleaning solvents.

No washer can completely remove oil.

DO NOT dry anything that has been soaked in or spotted with any type of oil.

DO NOT reach into the washer until all moving parts have stopped.

Doing so can result in death, explosion, fire or amputation.

WARNING - Fire Hazard

Loading Examples

Load Type Mixed Load Towels &

Sheets Delicates* Work Wear Small Load

(2-5 items)

Suggested

Cycle NORMAL TOWELS DELICATES JEANS Quick Wash

Load

Contents

6 Dress Shirts

3 Dress Pants

3 Poly T-Shirts

3 T-shirts

4 Pairs of Shorts

6 Boxers

OR

6 T-shirts

4 Sweatpants

4 Sweatshirts

2 Hoodies

7 Pairs of Socks

4 Pillowcases

2 Hand Towels

2 Flat Sheets/

2 Fitted Sheets

2 Bath Towels/

4 Washcloths

OR

2 Flat Queen-

Sized Sheets

2 Fitted Queen-

Sized Sheets

4 Pillowcases

7 Bras

7 Panties

3 Slips

2 Camisoles

4 Nightgowns

*Using a nylon

mesh bag for

small items is

recommended.

4 Jeans

5 Work Shirts

3 Work Pants

1 Pair Casual Pants

2 Casual Shirts

OR

3 Soccer Uniforms

20 49-3000368 Rev 0

Care and cleaning

CARE AND CLEANING

Self Clean

To clean the interior of the washer,

select the SELF CLEAN feature on the

control panel. This Self Clean cycle

should be performed, at a minimum,

once per month or about every 40 wash

cycles. This cycle will use more water,

in addition to bleach, to control the

rate at which soils and detergents may

accumulate in your washer.

NOTE: Read the instructions below

completely before starting Self Clean cycle.

1. Remove any garments or objects from the washer and

ensure the washer basket is empty.

2. Open the washer door and pour

one cup or 250 ml of liquid bleach

or other washing machine cleaner

into the basket.

3. Close the door and select the SELF CLEAN cycle.

Push the Start pad.

4. When the Self Clean cycle is working, the display will

show the estimated cycle time remaining. The cycle will

complete in about 90 minutes. Do not interrupt the cycle.

5. After the cycle is complete (on some models), the

washer will automatically start an ULTRAFRESH VENT

operation so that the door can remain closed until the

next time you use the washer.

If for any reason the cycle needs to be interrupted, the

door will not open immediately. Forcing open the door at

this stage may cause water to flood. The door will open

after the water is drained to a level where it would not

flood the floor.

Self Clean may be interrupted by pressing the Start pad

in between cycles. A power outage in the house might

also interrupt the cycle. When the power supply is back,

the Self Clean cycle resumes where it had stopped.

When interrupted, be sure to run a complete Self Clean

cycle before using the washer. If the Power pad is

pressed during Self Clean, the cycle will be lost.

IMPORTANT:

• Run Self Clean with one Cup (250 ml) of bleach once

a month.

• After the completion of a Self Clean cycle, the interior

of your washer may have a bleach smell.

• It is recommended to run a RINSE & SPIN or a light

color load after the Self Clean cycle.

Exterior

Immediately wipe off any spills. Wipe or dust spills or washing compounds with a damp cloth. Washer control panel

and finishes may be damaged by some laundry pretreatment and stain remover products. Apply these products

away from the washer. The fabric may then be washed and dried normally. Damage to your washer caused by these

products is not covered by your warranty. Do not hit surface with sharp objects.

Interior

Dry around the washer door opening, flexible gasket (including attached hoses) and door glass. These areas should

always be clean to ensure a watertight seal. You will notice if you regularly use the ULTRAFRESH VENT System that

this will not be required as often. It is recommended to rinse the washer at least once per month with 1 cup of bleach

(or other commercially available product manufactured for this purpose, such as Tide® Washing Machine Cleaner)

poured directly into the basket without clothes and using the Self Clean Cycle.

Water Supply Hoses

Periodically inspect all water inlet hoses for water leaks, wear, cuts, corrosion, and bulges. Replace all hoses immediately

if any sign of these failures appear. All hoses should be replaced every 5 years of use to reduce risk of hose failures

and possible water damage. When replacing hoses, refer to the Installation Instructions for proper installation. DO NOT

overtighten or cross thread fittings. DO NOT allow the hose to rub against sharp objects, become kinked, or become

over stretched. Always ensure hose rubber gaskets are installed and free from leaks when pressurized.

Door Gasket

Open the washer door. Using

both hands, press down the

door gasket.

While holding down the door

gasket, inspect the interior

fold. Remove any foreign

objects if found trapped

inside this gasket.

Make sure there is nothing blocking the

holes behind the gasket.

When you are finished cleaning the

door gasket, release it and the gasket

will return to the operating position.

Video

Scan this code

to watch a video

on this topic.

Video

Scan this code

to watch a video

on this topic.

La page charge ...

GE GFW850SSNWW Le manuel du propriétaire

GE GFW850SSNWW Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents