MooreCo Visionary Curve Assembly Instructions

Taper
Assembly Instructions
Visionary Curve
UPDATED AS OF: 03/05/2021
Part Numbers: 74955, 74957-XXXX
1 of 6
INSTRUCCIONES DE ENSEMBLAJE
NO LA TIRE
INSTRUCTIONS DE MONTAGE
NE PAS JETER
ASSEMBLY INSTRUCTIONS
DO NOT THROW AWAY!
P1 - Glass Board
P2A - Leg
P2B - Leg
P3 - Leg Connector
-Outer
P4 - Leg Connector
-Inner
P5 - Cap Channel
P6 - Tray
P7 - Tray Hanger
P8 - C-Frame
P9 - C-Frame Insert
P10 - Threaded Block
x2
x2
x2
x2
x2
x2
x1
x2
x2
x2
x2
A - CS Srew M6 x 10mm
B - Screw M6 x 15mm
C - Screw M8 x 65mm
D - Lock Washer
E - Locking Caster
F - Non-Locking Caster
G - M6 x 38mm All-Thread
H - Caster Wrench
I - Allen Wrench 4mm
J - Allen Wrench 5mm
x8
x8
x2
x4
x2
x2
x2
x1
x1
x1
Parts List
UPDATED AS OF: 03/05/2021 2 of 6
Hardware
For full product warranty details, please visit:
Para obtener información sobre la garantía del producto, consulte este sitio (ingles):
Pour plus d’informations sur la garantie du produit, consultez ce site (anglais):
For questions on assembly or missing/damaged parts, please contact us using the
following information.
Para preguntas sobre el ensamblaje o piezas faltantes o dañadas, por favor
contáctenos usando la siguiente información.
Pour toute question sur le montage l-assamblage manquantes ou endommagées,
veuillez nous contacter en utilisant les l’information ci-dessous.
To register your product for warranty, please visit:
Para registrar la garantía del producto, vea este sitio (en ingles):
Pour enregistrer la garantie de votre produit, consultez ce site (en anglais):
Review full assembly instructions and
check that all parts are present before
beginning assembly. Heavy or large
furniture may require multiple persons in
order to properly assemble. If you have
questions regarding assembly, contact
the manufacturer before continuing.
Damage due to incorrect assembly may
not be covered by warranty. Do not use
product unless all screws are tight. Check
all screws for tightness at least every
six months. If parts are broken, missing,
damaged, or worn, stop use of the product
until repairs are made by your dealer using
factory authorized parts.
WARNINGS AND DISCLAIMERS
WARRANTY
CARE & MAINTENANCE
PRODUCT REGISTRATION
UPDATED AS OF: 03/05/2021 3 of 6
Phone:
1.800.749. 2258
(Monday – Friday, 8AM – 5PM
Central Time)
http://moorecoinc.com/warranty
https://moorecoinc.com/register
Email:
support@moorecoinc.com
Previo a comenzar el proceso de
ensamblaje favor de revisar las
instrucciones y asegurarse que cuenta con
todas las partes y materiales necesarios.
Es posible que los muebles grandes o
pesados, requieran mas de una persona
para ensamblarlos correctamente. Por
favor contacte al fabricante directamente
si tiene alguna duda o pregunta antes de
continuar con el proceso de armado del
producto. La garantía no cubrirá daños
que ocurrieron por errores cometidos
durante el proceso de ensamblaje. Todos
los tornillos deben estar ajustados previo
el uso del producto. Debe revisar los
tornillos periódicamente, por lo menos
cada seis meses y asegurarse de que
estén bien ajustados. Por favor detenga
el uso del producto si partes del producto
se pierden, rompen, se deterioran por uso
o se rompen. Favor de contactar a su
distribuidor para que le envíen las partes
necesarias o realice las reparaciones
necesarias con partes autorizadas por el
fabricante.
Avant de commencer l’ assamblage
veuillez consulter les instructions
complètes et vérier si vous avez toutes
les pièces nécessaires. Ill est possible que
plusieurs personnes soient nécessaires
pour assemble des meubles grand ou
lourds. En cas de doute sur l assamblage
contactez le fabricant avant de continuer.
Les dommages encourus pendant
l’assamblage ne seront pas couvert par
la garantie. Ne pas utiliser le produit sans
vérier que tous les vis soient serrées.
Vériez que les vis sont serrées au moins
tous le 6 mois. Si aucune pièce se casse,
manque, est endommagée ou usée,
arrêtez d’ utiliser de produit jusqu’à ce
que le vendeur le repaire a l’aide de pièces
autorisées par la fabricant.
ADVERTENCIAS Y RENUNCIAS AVERTISSEMENTS
STEP 1
UPDATED AS OF: 03/05/2021 4 of 6
STEP 2
Screw in Caster with Lock Washer to Leg and tighten with Caster Wrench. Use Locking Casters on
same two leg parts (P2A or P2B) and Non-Locking Casters on the others. Repeat step for each leg.
Attach Leg Connector-Outer to Leg (P2B)
and Leg Connector-Inner to Leg (P2A) with
two screws each. Slide Leg with Inner into
Leg with Outer to join together. Repeat for
other leg set.
E/F
P2
D
P4
P3
A
P2B
P2A
STEP 3
UPDATED AS OF: 03/05/2021 5 of 6
STEP 4
Connect C-Frame pieces using C-Frame Inserts as shown. Ensure side holes in C-Frame line up
to each other. Use side hole to identify top of frame from bottom.
Screw in All-Threads into threaded holes in bottom of C-Frames. Place Cap
Channel over All-Threads and bottom of frame then screw Tray Hangers onto All-
Threads to secure Cap Channel. Connect Tray to Tray Hangers with two screws.
P4
P9
G
P7 P5
P6
B
Top
Bottom
Shorter
Longer
Bottom
STEP 5
UPDATED AS OF: 03/05/2021 6 of 6
STEP 6
Insert Glass Boards into Gap Channel on bottom of frame and hold both boards flush
with top of frame. Place second Gap Channel over top edge of boards and secure in
place with two screws.
THIS COMPLETES ASSEMBLY INSTRUCTION
Attach tray assembly to leg set by first sliding tray onto pins then
securing with two screws. Insert Threaded Block inside Leg
Connectors and insert screw into C-Frame side hole to tighten into
Threaded Block. Repeat step for second leg set.
B
P10 C
P1
B
P5
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

MooreCo Visionary Curve Assembly Instructions

Taper
Assembly Instructions

dans d''autres langues