MooreCo Trend Podium Desk Assembly Instructions

Taper
Assembly Instructions
Trend Podium Desk
UPDATED AS OF: 09/21/2021 1 of 7
INSTRUCCIONES DE ENSEMBLAJE
NO LA TIRE
INSTRUCTIONS DE MONTAGE
NE PAS JETER
ASSEMBLY INSTRUCTIONS
DO NOT THROW AWAY!
Parts List
UPDATED AS OF: 09/21/2021 2 of 7
Hardware
P1 - Table Top
P2 - Leg
P3 - Modesty Panel
P4 - Long Angle Support
P5 - Short Angle Bracket
x1
x1
x1
x1
x1
A - M6 x 15mm Screw
B - M6 x 42mm Screw
C - Locking Caster
D - Non-Locking Caster
E - Lock Washer
F - Allen Wrench
G - Caster Wrench
x13
x4
x1
x1
x2
x1
x1
For full product warranty details, please visit:
Para obtener información sobre la garantía del producto, consulte este sitio (ingles):
Pour plus d’informations sur la garantie du produit, consultez ce site (anglais):
For questions on assembly or missing/damaged parts, please contact us using the
following information.
Para preguntas sobre el ensamblaje o piezas faltantes o dañadas, por favor
contáctenos usando la siguiente información.
Pour toute question sur le montage l-assamblage manquantes ou endommagées,
veuillez nous contacter en utilisant les l’information ci-dessous.
To register your product for warranty, please visit:
Para registrar la garantía del producto, vea este sitio (en ingles):
Pour enregistrer la garantie de votre produit, consultez ce site (en anglais):
Review full assembly instructions and
check that all parts are present before
beginning assembly. Heavy or large
furniture may require multiple persons in
order to properly assemble. If you have
questions regarding assembly, contact
the manufacturer before continuing.
Damage due to incorrect assembly may
not be covered by warranty. Do not use
product unless all screws are tight. Check
all screws for tightness at least every
six months. If parts are broken, missing,
damaged, or worn, stop use of the product
until repairs are made by your dealer using
factory authorized parts.
WARNINGS AND DISCLAIMERS
WARRANTY
CARE & MAINTENANCE
PRODUCT REGISTRATION
UPDATED AS OF: 09/21/2021 3 of 7
Phone:
1.800.749.2258
(Monday – Friday, 8AM – 5PM
Central Time)
http://moorecoinc.com/warranty
https://moorecoinc.com/register
Email:
support@moorecoinc.com
Previo a comenzar el proceso de
ensamblaje favor de revisar las
instrucciones y asegurarse que cuenta con
todas las partes y materiales necesarios.
Es posible que los muebles grandes o
pesados, requieran mas de una persona
para ensamblarlos correctamente. Por
favor contacte al fabricante directamente
si tiene alguna duda o pregunta antes de
continuar con el proceso de armado del
producto. La garantía no cubrirá daños
que ocurrieron por errores cometidos
durante el proceso de ensamblaje. Todos
los tornillos deben estar ajustados previo
el uso del producto. Debe revisar los
tornillos periódicamente, por lo menos
cada seis meses y asegurarse de que
estén bien ajustados. Por favor detenga
el uso del producto si partes del producto
se pierden, rompen, se deterioran por uso
o se rompen. Favor de contactar a su
distribuidor para que le envíen las partes
necesarias o realice las reparaciones
necesarias con partes autorizadas por el
fabricante.
Avant de commencer l’ assamblage
veuillez consulter les instructions
complètes et vérier si vous avez toutes
les pièces nécessaires. Ill est possible que
plusieurs personnes soient nécessaires
pour assemble des meubles grand ou
lourds. En cas de doute sur l assamblage
contactez le fabricant avant de continuer.
Les dommages encourus pendant
l’assamblage ne seront pas couvert par
la garantie. Ne pas utiliser le produit sans
vérier que tous les vis soient serrées.
Vériez que les vis sont serrées au moins
tous le 6 mois. Si aucune pièce se casse,
manque, est endommagée ou usée,
arrêtez d’ utiliser de produit jusqu’à ce
que le vendeur le repaire a laide de pièces
autorisées par la fabricant.
ADVERTENCIAS Y RENUNCIAS AVERTISSEMENTS
STEP 1
UPDATED AS OF: 09/21/2021 4 of 7
Place a Lock Washer (E) on the threaded stem of the Locking Caster (C) and screw it
into the front Leg(P-2). Tighten with Caster Wrench (G). Place a Lock Washer (E) on
the threaded stem of the Non-Locking Caster (D) and screw it into the rear Leg (P-2)
and tighten with Caster Wrench (G) as shown in illustration #1.
STEP 2
Place the Desk Top (P-1) face down on a padded surface. Line the holes in the Leg (P-2)
attachment plate with the four threaded holes in the bottom of the Desk Top. Attach using
four Screws (A). Tighten with Allen Wrench (F).
P2
C
E
D
P1
P2
A
UPDATED AS OF: 09/21/2021 5 of 7
STEP 3
Attach the Modesty Panel (P-3) to the Leg (P-2) using three Screws (A) as shown in
illustration #3. Tighten with Allen Wrench (F).
STEP 4
Attach the Long Angle Supports (P-4) to the threaded insert under the cut-out of the
Desk Top (P-1) using three Screws (A). See illustration #4.
P2
P3
A
A
A
P1
P4
STEP 5
UPDATED AS OF: 09/21/2021 6 of 7
Attach the Trend Desk #58229 assembly from Step #5 to the Trend Podium #58230
assembly using the extra hardware from the Trend Desk #58229. Attach the Modesty
Panel (P-3) to the Podium’s Back Panel using two Screws (B) through the bottom two
holes in the Modesty Panel and into the the bottom threaded inserts in the Podium’s
Back Panel as shown in illustration #5.
STEP 6
Attach the top of the Modesty Panel (P-3) to the Podium’s Back Panel using two Screws (B)
inserted through the Short Angle Support (P-5) and into the threaded inserts in the top of
the Podium’s back. Use two Screws (A) to attach the Angle Support to the Table Top (P-1).
B
P3
P1
B
A
P5
58230
58229
STEP 7
UPDATED AS OF: 09/21/2021 7 of 7
Use three Screws (A) through the Long Angle Support (P-4) that is attached to the
bottom of the Table Top (P-1) and into the threaded inserts that are attached to the
Left Side Panel of the Podium.
A
P4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

MooreCo Trend Podium Desk Assembly Instructions

Taper
Assembly Instructions

dans d''autres langues