VTech VM928HD Guide de démarrage rapide

Catégorie
Moniteurs vidéo bébé
Taper
Guide de démarrage rapide
For operations and guides to help you using your video monitor,
and for latest information and supports, go and check the online
help topics and online FAQs.
Use your smartphone or mobile device to access our online help.
Go to https://help.vtechphones.com/vm928hd or
https://help.vtechphones.com/vm928-2hd; OR
Scan the QR code on the right. Launch the camera app or QR code scanner app
on your smartphone or tablet. Hold the device’s camera up to the QR code and
frame it. Tap the notification to trigger the redirection of the online help.
- If the QR code is not clearly displayed, adjust your camera’s focus by moving
your device closer or further away until it is clear.
You can also call our Customer Support at 1 (800) 595-9511 [in US] or
1 (800) 267-7377 [in Canada] for help.
NOTESNOTE
The rechargeable battery in the parent unit is built-in.
Use only the power adapters supplied with this product.
Make sure the parent unit and the baby unit are not connected to
the switch controlled electric outlets.
Connect the power adapters in a vertical or floor mount position
only. The adapters’ prongs are not designed to hold the weight of
the parent unit and the baby unit, so do not connect them to any
ceiling, under-the-table, or cabinet outlets. Otherwise, the adapters
may not properly connect to the outlets.
Make sure the parent unit, the baby unit and the power adapter
cords are out of reach of children.
To maintain compliance with the FCC’s RF exposure guidelines,
place the baby unit at least 20cm from nearby persons.
Specifications are subject to change without notice.
© 2022 VTech Communications, Inc. All rights reserved.
05/22. VM928-XHD_QSG_V2.
VM928HD
VM928-2HD
Full Color Pan and Tilt
HD Video Monitor
Go to www.vtechphones.com
to register your product for enhanced
warranty support and the latest VTech
product news.
1 Connect the baby monitor
2
Power on or off the baby monitor
What’s in the box
4
Status check
Once you power on both your
baby unit and parent unit, your
parent unit displays image from
the baby unit, and the LINK LED
light turns on.
The green LED light of the
baby unit turns on.
3 Positioning the baby monitor
Caution
The default volume of your parent unit is level
3, and the maximum volume is level 5. If you
experience high-pitched screeching noise from
your baby monitor while positioning:
- Make sure your baby unit and parent unit are
more than 3 feet (1 meter) apart, OR
- Lower the volume of your parent unit.
NOTESNOTE
Note
To avoid interference from other electronic
devices, place your baby monitor at least 3 feet
(1 meter) away from devices such as wireless
routers, microwaves, cell phones and computers.
Use the menu
Press MENU to enter the menu, choose a
menu item, or save a setting. You can use
the parent unit for advanced settings or
operations, such as to play or stop the baby
unit lullaby, or to adjust the baby unit sound
sensitivity.
While in the menu:
Press , , or to scroll among the
menu options.
Press SELECT to select an item, or to save
a setting.
Press TALK to return to the live video.
Press to go to the Help & info page.
Basic operation - Parent unit
Overview - Parent unit
Overview - Baby unit
Frequency control Crystal controlled PLL synthesizer
Transmit frequency Baby unit: 2.405-2.475GHz
Channels 32
LCD 5’’ Color LCD
(IPS 1280x720 pixels)
Nominal effective range Maximum power allowed by FCC and IC. Actual operating range may vary
according to environmental conditions at the time of use.
Power requirements Parent unit: 3.7V 5000mAh, 18.5Wh Lithium-ion battery
Baby unit power adapter: Output: 5V DC @ 1A
Parent unit power adapter: Output: 5V DC @ 2A
Technical specications
Important safety instructions
1LINK LED light
2 LED light
33- level sound indicator
light
4
Press to zoom in/out.
When in the main menu,
press to go to the
Help & Info page.
5TALK
Press and hold to talk to
the baby unit.
While in a submenu,
press to exit.
6Arrow keys
7MENU/SELECT
Press to enter the main
menu.
While in a menu, press to
choose an item, or save a
setting.
8- VOL/ VOL +
Increase or decrease
parent unit’s volume.
9Microphone
10 Antenna
11 Speaker
12 POWER key
13 Power jack
14 RESET
Force reboot the parent
unit.
15 Stand
1Microphone
2Camera lens
3Light sensor
4LED indicator
5Infrared LEDs
6 ON/OFF switch
7Antenna
8Speaker
9Temperature sensor
Position the sensor horizontally for
its optimal usage.
10 Power jack
11 Threaded socket for wall mounting
12 Pair button
1 set for VM928HD
2 sets for VM928-2HD
Need help?
S
m
Parent unit icons
Main menu
Monitoring mode (For VM928-2HD only)
Baby unit 1 in Single mode
Baby unit 2 in Single mode
Patrol mode
Split mode
Melodies and soothing sounds
Melodies and Soothing Sounds
Select play all melodies, or play one of the
five melodies and four soothing sounds.
Timer
You can also set the timer to stop playing
after 15, 30 or 60 minutes, or playing non-
stop.
Alerts - Sound, motion and temperature
Sound
Select sound Sensitivity level.
Turn on/off Sound Detection Alert.
Turn on/off Auto Wake Up function.
(See Sound Detection and Auto Wake Up
section)
Motion
Turn on/off Motion Alert.
Select motion Sensitivity level.
(See Motion Detection section)
Main menu
Temperature
Turn on/off Temperature Alert.
Set the parent unit to beep whenever the
room temperature detected by the baby
unit falls outside of the set temperature
range.
Select Minimum temperature for alert
range.
Select Maximum temperature for alert
range.
Select temperature Format.
Set temperature display in Fahrenheit (oF)
or Celsius (oC ).
Parent unit settings
Adjust parent unit screen Brightness.
Turn on/off Dim Mode.
Baby unit settings
Turn on/off baby unit’s Status LED.
Select Field of View.
Choose Wide angle or Standard .
Adjust baby unit’s speaker Volume.
General settings
Turn on/off Low Battery Alert Tone.
Set the parent unit to beep when the
battery is low.
Turn on/off No Link Alert Tone.
Set the parent unit to beep when the link
between the parent unit and the baby unit
is lost.
Main menu icons
VM928HD
VM928-2HD
Quick start guide VM928HD VM928-2HD
For more support information
S
m
x 2
x 2
Quick start guide
Strangulation
Hazard
Keep this cord out of reach of children.
The cord needs to be at least three feet
away from the child at all times. Do not
use with an extension cord. Do not
remove this tag.
Éloignez ce cordon des enfants. Le
cordon doit se trouver à au moins trois
pieds d’un enfant et ce, en tout temps.
N’utilisez pas de rallonge. Ne retirez pas
cette étiquette.
Mantenga este cable fuera de la alcance
de los niños. Este cable debe estar por
lo menos tres pies fuera de la alcance
del niño en todo momento. No lo use
con una extensión inalámbrica. No quite
esta etiqueta.
Risque
d’étranglement
Riesgo de
estrangulación
Charge the parent unit battery before use
When you have connected and
turned on the parent unit, the battery
will be charged automatically.
NOTESNOTE
Notes
Before using the baby monitor for the
first time, charge the parent unit battery
for 12 hours. When the parent unit
battery is fully charged, the battery icon
becomes solid .
It takes longer to charge the battery
when the parent unit is turned on. To
shorten the charging time, turn the
parent unit off while charging.
The standby time varies depending on
the sensitivity level you set, your actual
use and the age of the battery.
The battery icon indicates the battery status (see the following table).
Battery indicators Battery status Action
The screen displays .
The light flashes.
The battery has very little
charge and may be used for
only a short time.
Charge
without interruption
(about
30 minutes).
The battery icon becomes
solid .
The battery is fully charged. To keep the battery charged, connect
it to AC power when not in use.
Slide the switch to ON to power on
your baby unit. After the parent unit is fully charged,
press POWER until the welcoming
screen appears.
Raise the parent unit antenna
for better reception
1
Connect the baby monitor (Cont’d)
> 3ft (1m)
< 3m
> 3m
< 3ft (1m)
3ft (1m)
Adjust speaker volume
Press - VOL/ VOL + to adjust your parent unit
speaker volume. It determines the volume of
sound transmitted from your baby unit.
Zoom
Press to zoom in or out.
Talk to your baby via the baby unit
1. Press and hold the TALK key.
2. When the icon displays on screen,
speak to your parent unit. Your voice is
transmitted to the baby unit.
3. When finish talking, release
the TALK key and hear your baby again.
Press and hold
Turn on/off the parent unit screen
You can turn on or off the parent unit
screen without powering off the parent
unit. You can still hear sound from the
baby unit.
Press POWER on the parent unit to
turn off the screen.
Press any keys on the parent unit to
turn on the screen again.
2
1
3
4
5
6
7
8
15
12
11
10
13
14
1
6
12
11
10
2
3
5
7
8
9
4
1
6
12
11
10
2
3
5
7
8
9
4
1
6
12
11
10
2
3
5
7
8
9
4
or
Current view status
The baby unit number that is being viewed
when in:
-Single CAM mode.
-Patrol mode (* For VM928-2HD only).
-Split mode (* For VM928-2HD only).
Split mode
(* For VM928-2HD only)
Patrol mode
(* For VM928-2HD only)
Night vision feature is activated automatically.
Motion alert is turned on.
Sound detection alert is turned on.
Melodies or soothing sound are turned on.
Parent unit speaker is muted.
Temperature alert is turned on.
Status icons
Alert icons
Displays when parent unit’s battery is low
and needs charging.
Displays when motion is detected at a baby
unit.
Displays when sound is detected at a baby
unit.
Baby unit detects temperature exceeds the
set maximum.
Baby unit detects temperature is lower than
the set minimum.
The applied nameplate is located at the bottom of the baby unit’s
base.
When using your equipment, basic safety precautions should
always be followed to reduce the risk of fire, electric shock and
injury, including the following:
1. Follow all warnings and instructions marked on the product.
2. Adult setup is required.
3. CAUTION: Do not install the baby unit at a height above 2
meters.
4. This product is intended as an aid. It is not a substitute for
responsible and proper adult supervision and should not be
used as such.
5. This product is not intended for use as a medical monitor.
6. Do not use this product near water. For example, do not use
it next to a bath tub, wash bowl, kitchen sink, laundry tub or
swimming pool, or in a wet basement or shower.
7. CAUTION: Use only the battery provided. There may be a risk
of explosion if a wrong type of battery is used for the parent
unit. The battery cannot be subjected to high or low extreme
temperature and low air pressure at high altitude during use,
storage or transportation. Disposal of battery into fire or a hot
oven, or mechanically crushing or cutting or the battery can
result in an explosion. Leaving the battery in an extremely
high temperature surrounding environment can result in an
explosion or the leakage of flammable liquid of gas. Battery
subjected to extremely low air pressure may result in an ex-
plosion or the leakage of flammable liquid or gas. Dispose of
used battery according to the information in The RBRC seal.
8. Use only the adapters included with this product. Incorrect
adapter polarity or voltage can seriously damage the product.
Power adapter information:
Baby Unit Output: 5V DC 1A
VTech Telecommunications Ltd.
Model: VT05EUS05100
Parent Unit Output: 5V DC 2A
VTech Telecommunications Ltd.
Model: VT07EUS05200
Rechargeable battery information:
3.7V 5000mAh, 18.5Wh Lithium-ion Battery
Zhuhai Great Power Energy Co., Ltd.
Model: GSP806090-5Ah-3.7V-1S1P
9. The power adapter is intended to be correctly oriented in a
vertical or floor mount position. The prongs are not designed
to hold the plug in place if it is plugged into a ceiling, un-
der-the-table or cabinet outlet.
10. For pluggable equipment, the socket-outlet (power adapter)
shall be installed near the equipment and shall be easily
accessible.
11. Unplug this product from the wall outlet before cleaning.
Do not use liquid or aerosol cleaners. Use a damp cloth for
cleaning.
12. Do not cut off the power adapters to replace them with other
plugs, as this causes a hazardous situation.
13. Do not allow anything to rest on the power cords. Do not
install this product where the cords may be walked on or
crimped.
14. This product should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supply in your home, consult your dealer or
local power company.
15. The equipment is to be supplied from an identified USB port
complying with the requirements of Limited Power Source.
16. Do not overload wall outlets or use an extension cord.
17. Do not place this product on an unstable table, shelf, stand or
other unstable surfaces.
18. This product should not be placed in any area where proper
ventilation is not provided. Slots and openings in the back or
bottom of this product are provided for ventilation. To protect
them from overheating, these openings must not be blocked
by placing the product on a soft surface such as a bed, sofa
or rug. This product should never be placed near or over a
radiator or heat register.
19. Never push objects of any kind into this product through
the slots because they may touch dangerous voltage points
or create a short circuit. Never spill liquid of any kind on the
product.
20. To reduce the risk of electric shock, do not disassemble this
product, but take it to an authorized service facility. Opening
or removing parts of the product other than specified access
doors may expose you to dangerous voltages or other risks.
Incorrect reassembling can cause electric shock when the
product is subsequently used.
21. You should test the sound reception every time you turn on
the units or move one of the components.
22. Periodically examine all components
for damage.
23. There is a very low risk of privacy loss when using certain elec-
tronic devices, such as baby monitors, cordless telephones,
etc. To protect your privacy, make sure the product has never
been used before purchase, reset the baby monitor period-
ically by powering off and then powering on the units, and
power off the baby monitor if you will not use it for some time.
24. Children should be supervised to ensure that they do not play
with the product.
25. The small parts of this monitor can be swallowed by babies or
small children. Keep these parts out of reach of children.
26. The product is not intended for use by persons (including
children) with reduced physical, sensory or mental capabili-
ties, or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
SAVE THESE INSTRUCTIONS
Cautions
Use and store the product at a temperature between 32oF and
104oF.
Burn hazard, fire hazard, explosion hazard associated with
mishandling of the battery.
Do not expose the product to extreme cold, heat or direct
sunlight. Do not put the product close to a heating source.
Warning—Strangulation Hazard—
Children have STRANGLED in cords. Keep this
cord out of the reach of children (more than 3 ft
(0.9m) away). Do not remove this tag.
Never place the camera unit(s) inside the baby’s
crib or playpen. Never cover the camera unit(s)
or parent unit with anything such as a towel or a blanket.
Other electronic products may cause interference with your
camera unit. Try installing your camera unit as far away from
these electronic devices as possible: wireless routers, radios,
cellular telephones, intercoms, room monitors, televisions,
personal computers, kitchen appliances and cordless tele-
phones.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless devices):
Wireless Technology Research, LLC (WTR), an independent
research entity, led a multidisciplinary evaluation of the
interference between portable wireless devices and implanted
cardiac pacemakers. Supported by the U.S. Food and Drug
Administration, WTR recommends to physicians that:
Pacemaker patients
Should keep wireless devices at least six inches from the
pacemaker.
Should NOT place wireless devices directly over the pacemak-
er, such as in a breast pocket, when it is turned ON.
WTR’s evaluation did not identify any risk to bystanders with
pacemakers from other persons using wireless devices.
Electromagnetic elds (EMF)
This VTech product complies with all standards regarding
electromagnetic fields (EMF). If handled properly and according
to the instructions in this user’s manual, the product is safe to be
used based on scientific evidence available today.
Strangulation
Hazard
Keep this cord out of reach of children.
The cord needs to be at least three feet
away from the child at all times. Do not
use with an extension cord. Do not
remove this tag.
Éloignez ce cordon des enfants. Le
cordon doit se trouver à au moins trois
pieds d’un enfant et ce, en tout temps.
N’utilisez pas de rallonge. Ne retirez pas
cette étiquette.
Mantenga este cable fuera de la alcance
de los niños. Este cable debe estar por
lo menos tres pies fuera de la alcance
del niño en todo momento. No lo use
con una extensión inalámbrica. No quite
esta etiqueta.
Risque
d’étranglement
Riesgo de
estrangulación
Night vision
The baby unit has infrared LEDs that allow
you to see your baby clearly at night or in
a dark room. When the baby unit being
viewed detects low light levels, the infrared
LEDs are switched on automatically. The
images from the baby unit are in black and
white, and appears on the screen.
Notes
It is normal if you see a short white glare on
your parent unit screen as the baby unit is
adapting to the dark environment.
When the infrared LEDs are on, the images are
in black and white. This is normal.
Tip
Depending on the surroundings and other
interfering factors, like lightings, objects, colors
and backgrounds, the video quality may vary.
Adjust the baby unit’s angle or place the baby
unit at a higher level to prevent glare and
blurry display.
Mount the baby unit on dry wall (optional)
For VM928-2HD only
Select Patrol mode as your monitoring
mode to alternately view the image
from baby units and every
10 seconds.
Change different views - Patrol
Select Split mode as your monitoring mode to view the images
from both baby units at once.
Note
While in Split mode, you can press or to highlight the view of the baby unit 1 or
baby unit 2 , and hear the sounds transmitted from the baby unit.
Change different views - Split
Sound Detection and Auto Wake UP
Sound activated screen and audio - Auto Wake Up
Adjust sound detection sensitivity
When Auto Wake Up is turned on,
the parent unit screen stays off to
save power when the baby unit
detects no sound.
Once the baby unit detects sounds
that are louder than the chosen
sound sensitivity level, the parent
unit screen and speaker turn on
automatically. The parent unit will
then turn off again after 50 seconds
of no sound detection.
NOTESNOTE
Notes
If you have muted the parent unit
speaker, only the parent unit screen
will turn on when a sound is detected.
If you have turned on Auto Wake
Up but turned off Sound Detection
Alert, the parent unit will wake up
when the baby unit detects sounds
that are louder than the chosen sound
sensitivity level.
You can turn on Sound Detection Alert and adjust the Sound Sensitivity to detect sounds
and turn on the parent unit while its screen is switched off or dimmed.
When the baby unit detects sounds that exceed certain levels, the parent unit screen will
turn on and the baby unit starts transmitting the sounds to the parent unit, and you can
see and hear your baby.
If you have turned on Sound Detection Alert, the parent unit beeps when the baby unit
detect sounds.
The RBRC seal on the lithium-ion battery indicates that VTech Communications, Inc. is voluntarily
participating in an industry program to collect and recycle these batteries at the end of their useful lives,
when taken out of service within the United States and Canada.
The program provides a convenient alternative to placing used lithium-ion batteries into the trash or
municipal waste, which may be illegal in your area.
VTech’s participation makes it easy for you to drop off the spent battery at local retailers participating in the program or
at authorized VTech product service centers. Please call 1 (800) 8 BATTERY® for information on Li-ion battery recycling and
disposal bans/restrictions in your area. VTech’s involvement in this program is part of its commitment to protecting our
environment and conserving natural resources.
The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks of Call2recycle, Inc.
What does this limited warranty cover?
The manufacturer of this VTech product, VTech
Communications, Inc. (VTech”), warrants to the holder
of a valid proof of purchase (“Consumer” or “you”) that
the Product and all accessories provided by VTech in
sales package (“Product) are free from material defects
in material and workmanship, pursuant to the following
terms and conditions, when installed and used normally
and in accordance with operating instructions. This limited
warranty extends only to the Consumer for Products
purchased and used in the United States of America and
Canada.
What will VTech do if the Product is not free from defects
in materials and workmanship during the limited warranty
period (“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized
service representative will replace at VTech’s option,
without charge, a Materially Defective Product. If we choose
to replace the Product, we may replace it with a new or
refurbished Product of the same or similar design. VTech will
return replacement products to you in working condition.
VTech will retain defective parts, modules, or equipment.
Replacement of the Product, at VTech’s option, is your
exclusive remedy. You should expect the replacement to
take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the product extends for
ONE (1) YEAR from date of purchase (90 days on products
purchased as Refurbished*). This limited warranty also
applies to replacement Products for a period of either (a)
90 days from the date the replacement Product is shipped
to you or (b) the time remaining on the original one-year
limited warranty (90-day limited warranty on products that
are purchased as Refurbished*). Whichever is longer.
*Refurbished products purchased from our online store
carry a 90-day replacement warranty.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident,
shipping or other physical damage, improper installation,
abnormal operation or handling, neglect, inundation,
fire, water or other liquid intrusion; or
2. Product that has been damaged due to repair, alteration
or modification by anyone other than an authorized
service representative of VTech; or
3. Product to the extent that the problem experienced is
caused by signal conditions, network reliability, or cable or
antenna systems; or
4. Product to the extent that the problem is caused by use
with non-VTech accessories; or
5. Product whose warranty/quality stickers, product serial
number plates or electronic serial numbers have been
removed, altered or rendered illegible; or
6. Product purchased, used, serviced, or shipped for repair
from outside the United States of America or Canada, or
used for commercial or institutional purposes (including
but not limited to Products used for rental purposes); or
7. Product returned without a valid proof of purchase (see
item 2 below); or
8. Charges for installation or set up, adjustment of customer
controls, and installation or repair of systems outside the
unit.
How do you get warranty service?
To obtain warranty service in the United States of America,
please visit our website at www.vtechphones.com or call
1 (800) 595-9511 for instructions regarding where to return
the Product.In Canada, go to phones.vtechcanada.com or
dial 1 (800) 267-7377.
NOTE: Before calling for service, please review the user’s
manual - a check of the Product’s controls and features
may save you a service call.
Except as provided by applicable law, you assume the risk
of loss or damage during transit and transportation and
are responsible for delivery or handling charges incurred
in the transport of Product(s) to the service location. VTech
will return replaced product under this limited warranty to
you, transportation, delivery or handling charges prepaid.
VTech assumes no risk for damage or loss of the Product
in transit.
What must you return with the Product to get warranty
service?
1. Return the entire original package and contents including
the Product to the VTech service location along with a
description of the malfunction or difficulty; and
2. Include a “valid proof of purchase” (sales receipt)
identifying the Product purchased (Product model) and
the date of purchase or receipt; and
3. Provide your name, complete and correct mailing
address, and telephone number.
Other limitations
This warranty is the complete and exclusive agreement
between you and VTech. It supersedes all other written
or oral communications related to this product. VTech
provides no other warranties for this product. The warranty
exclusively describes all of VTech’s responsibilities
regarding the product.
There are no other expressed warranties. No one is
authorized to make modifications to this warranty and you
should not rely on any such modification.
State Law Rights: This warranty gives you specific legal
rights, and you also have other rights which vary from state
to state.
Limitations: Implied warranties, including those of fitness for
a particular purpose and merchantantability (an unwritten
warranty that the product is fit for ordinary use) are limited
to one year from date of purchase. Some states do not allow
limitations on how long an implied warranty lasts, so the
above limitation may not apply to you.
In no event shall VTech be liable for any indirect, special,
incidental, consequential, or similar damages (including,
but not limited to lost profits or revenue, inability to use
the product, or other associated equipment, the cost of
substitute equipment, and claims by third parties) resulting
from the use of this product. Some states do not allow
the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not
apply to you.
Please retain your original sales receipt as proof
of purchase.
This baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby monitor
is set up to comply with the energy-conserving standards right out of the box. Follow the instructions to install and charge
the battery. The CEC battery charging testing mode is activated while charging. Even if the parent unit is paired to baby
units, the CEC battery charging testing mode is activated while it is powered off and charging.
FCC Part 15
This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the
Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to this equipment not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed
by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with
the FCC criteria. The baby unit shall be installed and used such that parts of all persons’ body are maintained at a distance of
approximately 8 in (20 cm) or more. The transmitter and antenna of the parent unit shall be held at least 1 in (2.5 cm) from your
face.
This Class B digital apparatus complies with Canadian requirement:
CAN ICES-3 (B)/NMB-3(B)
Industry Canada
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development
Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause
interference. (2) This device must accept any interference, including interference that may cause undesired operation of the
device.
The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry Canada technical specifications were
met.
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.
RF radiation exposure statement
The baby unit complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The baby unit should
be installed and operated with a minimum distance of 8 in (20 cm) between the baby unit and all persons’ body. Use of other
accessories may not ensure compliance with FCC RF exposure guidelines. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter. This equipment complies also with Industry Canada RSS-102 with respect
to Canada’s Health Code 6 for Exposure of Humans to RF Fields.
The RBRC seal For cETL compliance only Limited warranty
California Energy Commission battery
charging testing mode
FCC and IC regulations
10s
The parent unit display will dim to conserve energy after 5 minutes of inactivity, in
which there is neither key pressed nor alert received from the baby unit.
Dim mode
5 minute inactivity
Press any buttons
Sound
Sensitivity
level
Level 3
(Highest)
Level 2
(Medium)
Level 1
(Lowest)
Description The parent unit screen and
speaker turn on for very
small sounds, including
background noises from
your baby’s room.
The parent unit screen and
speaker turns on for loud
babbling and louder sounds
from your baby. The parent
unit remains quiet when your
baby makes soft sounds.
The parent unit screen
and speaker turn on for
loud crying or screeching
sounds from your baby.
The parent unit remains
quiet when your baby
makes soft sounds.
1. Place the wall mount bracket on a wall and then use
a pencil to mark the top and the bottom holes as
shown. Remove the wall mount bracket and drill
two holes in the wall (7/32 inch drill bit).
NOTESNOTE
Notes
Check for reception strength and baby unit’s angle before drilling the holes.
The types of screws and anchors you need depend on the composition of the wall. You may need to purchase the screws and anchors separately to mount your baby units.
2. If you drill the holes into a stud, go to step 3.
If you drill the holes into an object other than a stud, insert the wall
anchors into the holes. Tap gently on the ends with a hammer until the
wall anchors are flush with the wall.
3. Align the wall mount bracket and screws with the
holes in the wall as shown. Tighten the screw in the
middle hole first, so that the wall mount bracket
position is fixed. You can tighten the other screw in
the top hole.
3. Insert the screws into the holes and tighten the screws until only 1/4 inch
of the screws are exposed.
4. Place the baby unit on the wall mount bracket.
Tighten the screw into the threaded socket
at the bottom to secure the baby unit. Align
the holes on the wall mount bracket with the
screws on the wall, and slide the wall mount
bracket down until it locks into place.
5. You can maximize your baby unit’s viewing angles by tilting the wall mount bracket.
Hold the baby unit, and then rotate the knob in anticlockwise direction. This will loosen the joint of the wall mount bracket.
Tilt your baby unit up or down to adjust to your preferred angle. Then, rotate the knob in clockwise direction to tighten the joint and
secure the angle.
OR
4. Place the baby unit on the wall mount bracket.
Tighten the screw into the threaded socket at the
bottom to secure the baby unit.
1
2
Motion Detection
Adjust motion detection sensitivity
You can turn on Motion Alert and adjust the Motion Sensitivity to detect motions and
turn on the parent unit while its screen is switched off or dimmed.
When the baby unit’s camera detects motions that exceed certain levels, the parent unit
screen will turn on and the baby unit starts transmitting the sounds to the parent unit, and
you can see and hear your baby.
If you have turned on Motion Alert, the parent unit beeps when the baby unit detects
motions.
Motion
Sensitivity
level
Level 3
(Highest)
Level 2
(Medium)
Level 1
(Lowest)
Description The parent unit screen and
speaker turn on for small
motions, such as yawning or
stretching.
The parent unit screen and
speaker turns on for normal
daily motions, such as
people walking around the
house.
The parent unit screen and
speaker turn on for large
motions, such as children
are chasing or jumping
around.
Monitoring mode
Change different views - Single CAM
Select baby unit 1 or baby unit 2 to
view the image from the baby unit.
Below are the questions most frequently asked about the baby monitor.
Why does the baby
monitor not respond
normally?
Try the following (in the order listed) for common cure:
1. Disconnect the power to the baby units and the parent unit.
2. Wait a few seconds before connecting power back to the baby units and the parent unit.
3. Turn on the baby units and the parent unit.
4. Wait for the parent unit to synchronize with the baby units. Allow up to one minute for
this to take place.
Why don’t the lights of
the baby unit and parent
unit go on when I switch
on the units?
Perhaps the parent unit’s battery is depleted. Insert the appliance plug into the parent
unit and put the adapter in a wall socket. The parent unit will establish connection with
the baby unit.
Perhaps the baby unit is not connected to the power. Insert the appliance plug into the
baby unit and put the adapter in a wall socket. Then, slide the ON/OFF to switch on the
baby unit and to establish connection with the parent unit.
Why doesn’t my parent
unit charge while
connected to AC power?
Make sure the power is not controlled by a wall switch.
Why is my screen in black
and white?
The screen is in black and white during night-time or in a dark room when the night
vision feature is activated. This is normal.
Why do I get glare or
blurry display on my
screen when viewing my
baby at night?
During night-time or in a dark room, the surroundings and other interfering factors,
like lightings, objects, colors and backgrounds may affect the image quality on your
parent unit screen. Adjust the baby unit’s angle or place the baby unit at a higher level to
prevent glare and blurry display.
Why does the baby
monitor produce a
high-pitched noise?
The parent unit and baby units may be too close to each other.
Move the parent unit away from the baby units until the noise stops; OR
Turn down the volume of your parent unit.
Why does the parent unit
beep?
The baby units may be out of range. Move the parent unit closer to the baby units (but
not less than 3 feet).
The parent unit may not have enough charge for the parent unit to perform normally.
Charge the battery in the parent unit until the battery icon becomes solid .
The temperature of your baby’s room may be too high or too low.
Why don’t I hear a sound/
Why can’t I hear my baby
cry?
The parent unit speaker volume may be too low. Press VOL+ to increase the volume, or
use the parent unit menu to change sound sensitivity level to the highest level.
Why can’t I establish a
connection? Why is the
connection lost every now
and then? Why are there
sound interruptions?
The baby units may be out of range. Move the parent unit closer to the baby units (but
not less than 3 feet).
Other electronic and wireless products may cause interference with your baby monitor.
Try installing your baby monitor as far away from these devices as possible.
If you power on only one baby unit, your parent unit may display Make sure baby unit X
is on or move closer to baby unit X, and the LINK LED light flashes. Switch to the baby unit
you have powered on via menu.
Frequently asked questions
Mesures de sécurité importantes
La plaque signalétique appliquée est située au bas du socle de l’unité
du bébé.
Lorsque vous utilisez votre appareil, vous devriez toujours suivre
certaines mesures de précaution de base afin de réduire les risques
d’incendie, d’électrocution et de blessures corporelles, dont ceux qui
suivent:
1. Observez toutes les instructions et mises en garde inscrites sur
l’appareil.
2. L’installation par un adulte est requise.
3. MISE EN GARDE: N’installez pas l’unité du bébé à une hauteur
supérieure à 2 mètres.
4. Ce produit a été conçu pour être un dispositif d’appoint seulement.
Il n’est pas le remplacement d’une supervision responsable et
adéquate par un adulte et ne devrait pas être utilisé comme telle.
5. Ce produit n’est pas conçu pour être utilisé en tant que moniteur
médical.
6. N’utilisez pas cet appareil près de l’eau ni de toute autre source
d’humidité, par exemple, près d’une baignoire, cuve à lessive,
évier de cuisine, dans un sous-sol humide ni près d’une piscine,
dans un soussol humide ou une douche.
7. MISE EN GARDE: Utilisez uniquement la pile fournie. Un risque
d’explosion pourrait survenir si un mauvais type de pile est utilisé
pour l’unité du parent. La pile ne peut pas être soumise à des
températures extrêmes élevées ou basses et à une faible pression
d’air à haute altitude pendant l’utilisation, l’entreposage ou le
transport. L’élimination de la pile dans le feu ou dans un four chaud,
ou l’écrasement ou le découpage mécanique de la pile peuvent
entraîner une explosion. Laisser la pile dans un environnement à
température extrêmement élevée peut entraîner une explosion
ou la fuite d’un liquide ou d’un gaz inflammable. Une pile soumise
à une pression d’air extrêmement basse peut provoquer une
explosion ou une fuite de liquide ou de gaz inflammable. Éliminer
la pile usagée conformément aux informations du Sceau RBRC.
8. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation
d’un adaptateur dont la polarité ou la tension serait inadéquate
risque d’endommager sérieusement le produit et mettre votre
sécurité en péril.
Informations sur les adaptateurs électriques :
Adaptateur de l’unité du bébé: Sortie : 5 V CC 1A.
VTech Telecommunications Ltd.
Modèle : VT05EUS05100
Adaptateur de l’unité du parent: Sortie : 5 V CC 2A.
VTech Telecommunications Ltd.
Modèle : VT07EUS05200
Informations sur les piles rechargeables :
3.7V 5000mAh, 18.5Wh Lithium-ion Battery
Zhuhai Great Power Energy Co., Ltd.
Modèle : GSP806090-5Ah-3.7V-1S1P
9. Lorsqu’ils sont branchés dans une prise de courant, les adaptateurs
secteur ont été conçus pour être orientés correctement, soit à la
verticale ou au plancher. Les broches n’ont pas été conçues pour
supporter le poids du bloc d’alimentation et le maintenir en place
si celuici est branché dans une prise au plafond, sous une table ou
dans un meuble.
10. Pour les appareils raccordés, la prise de courant (de l’adaptateur
secteur) doit être installée près de l’équipement et doit être
facilement accessible.
11. Débranchez ce produit de la prise de courant avant de procéder
au nettoyage. N’utilisez pas de nettoyants en aérosols. Utilisez un
chiffon humide pour le nettoyer.
12. Ne coupez pas les cordons d’alimentation pour remplacer les
fiches, car ceci peut présenter un danger potentiel.
13. Ne laissez aucun objet reposer ni appuyer sur le cordon
d’alimentation. N’installez pas cet appareil dans un endroit où
l’on risque d’écraser le cordon d’alimentation ou de le piétiner.
14. Ne faites fonctionner cet appareil qu’avec le type d’alimentation
indiqué sur l’étiquette. Si vous ne connaissez pas le type
d’alimentation que vous possédez à votre domicile, consultez votre
marchand ou votre compagnie locale d’électricité.
15. L’équipement doit être fourni à partir d’un acquiescement gauche
identifié d’USB aux conditions de la source d’énergie limitée.
16. Ne surchargez pas les prises de courant murales ni les rallonges
électriques.
17. Ne placez pas cet appareil sur un chariot, meuble, trépied, support
de montage ni table chancelants.
18. Les trous et ouvertures du boîtier, situés à l’arrière de l’appareil
ou sous celui-ci, servent à aérer l’appareil. Pour l’empêcher de
surchauffer, ne bloquez sous aucun prétexte ces ouvertures
et n’empêchez pas l’aération adéquate de l’appareil en le
plaçant sur un lit, divan, tapis ou toute autre surface similaire.
De même, ne le positionnez pas à proximité ni au-dessus d’une
source de chaleur ou d’un calorifère. De plus, ne placez pas
l’appareil dans un endroit avant de vous assurer qu’il y ait une
bonne circulation d’air.
19. N’enfoncez jamais d’objets à travers les ouvertures de cet appareil,
car ils pourraient entrer en contact avec des points de tension
dangereux ou causer des courts-circuits qui peuvent dégénérer
en incendies ou en risques d’électrocution. Ne renversez jamais
de liquide dans ce produit.
20. Afin de réduire les risques d’électrocution, ne démontez pas cet
appareil, mais apportez-le dans un centre de service autorisé.
L’ouverture du boîtier ou le retrait de toutes pièces que contient
cet appareil, à l’exception de l’accès autorisé à certaines portes
ou ouvertures, risque de vous exposer à des points de tension
dangereux ou d’autres dangers. Un remontage incorrect peut par
la suite présenter des risques d’électrocution.
21. Vous devriez tester la réception chaque fois que vous mettez
l’appareil en fonction.
22. Examinez les composantes afin de vérifier si celles-ci ne sont pas
endommagées.
23. Il existe un très faible risque de perte de confidentialité avec
certains appareils électroniques (autres écoute-bébés, téléphones
sans fils etc.). Pour l’éviter, s’assurer que le produit n’a jamais été
utilisé avant l’achat, réinitialiser l’unité de façon périodique, éteindre
l’écoute-bébé quand il n’est pas en cours d’utilisation.
24. Les enfants devraient être supervisés afin de vous assurer qu’ils ne
jouent pas avec l’appareil.
25. Les petites pièces de ce moniteur peuvent être avalées par les
bébés ou les petits enfants. Veuillez tenir ces pièces hors de
portée des enfants.
26. Le produit n’est pas conçu pour être utilisé par des personnes
(incluant des enfants) aux capacités physiques, sensorielles
ou mentales réduites ou qui manquent d’expérience et de
connaissances, à moins qu’on leur ait donné suffisamment de
supervision ou d’instructions relativement à l’utilisation de l’appareil
par une personne responsable de leur sécurité.
CONSERVEZ CES INSTRUCTIONS
Mises en garde
Utilisez et entreposez le produit à une température entre 0˚ C
(32˚F) et 40˚C (104˚ F).
Risque de brûlure, risque d’incendie, risque d’explosion associé à
une mauvaise manipulation de la batterie.
N’exposez pas cet appareil à des froids ou des chaleurs extrêmes,
ainsi qu’à la lumière directe du soleil. Ne l’installez pas près d’une
source de chauffage.
Avertissement - Risque de strangulation
- Les enfants se sont ÉTRANGLÉS dans des cordons.
Gardez ce cordon hors de portée des enfants (à
plus de 0,9 m). N’enlevez pas cette étiquette.
Ne jamais placer le moniteur à l’intérieur du berceau ou du parc
de bébé. Ne jamais couvrir le moniteur ou l’unité (s) portative avec
un article tel une serviette ou une couverture.
D’autres produits électroniques peuvent causer des interférences
auprès de votre caméra IP. Essayez d’installer votre caméra IP le
plus loin possible de ces dispositifs électroniques : routeurs sans fil,
radios, téléphones cellulaires, interphones, moniteurs de pièces,
téléviseurs, ordinateurs personnels, appareils électriques de cuisine
et téléphones sans fil.
Stimulateurs cardiaques implantés dans l’organisme
Les simulateurs cardiaques (ne s’applique qu’aux dispositifs
numériques sans fil):
L’organisme ‘Wireless Technology Research, LLC (WTR)’, une firme
de recherche indépendante, a mené une évaluation pluridisciplinaire
des interférences entre les téléphones sans fil portatifs et les
stimulateurs cardiaques implantés dans l’organisme. Appuyée par
l’Administration des aliments et drogues (FDA) des États-Unis, la firme
WTR recommande aux médecins:
Avis aux détenteurs de stimulateurs cardiaques
Vous devriez maintenir les dispositifs sans fil à au moins six pouces
du simulateur cardiaque.
Ils ne doivent PAS placer le téléphone sans fil directement sur le
stimulateur cardiaque, tel que dans une poche de chemise, lor-
sque celui-ci est en marche.
L’étude effectuée par l’organisme WRS n’a pas identifié de risque
pour les détenteurs de simulateurs cardiaques causés par les gens qui
utilisent dispositifs sans fil à proximité de ceux-ci.
Champs électromagnétiques (EMF)
Ce produit de VTech est conforme à toutes les normes se rapportant
aux champs électromagnétiques (EMF) standard. Si vous le manipulez
correctement en suivant les instructions de ce guide, son utilisation
sera sécuritaire pendant de nombreuses années, selon les meilleures
évidences scientifiques dont nous disposons aujourd’hui.
CABLE MANAGEMENT
1 2 3
  • Page 1 1
  • Page 2 2

VTech VM928HD Guide de démarrage rapide

Catégorie
Moniteurs vidéo bébé
Taper
Guide de démarrage rapide

dans d''autres langues