VTech VM928HD Guide de démarrage rapide

Marque: VTech

Modèle: VM928HD

Catégorie: Moniteurs vidéo bébé

Taper: Guide de démarrage rapide

For operations and guides to help you using your video monitor,

and for latest information and supports, go and check the online

help topics and online FAQs.

Use your smartphone or mobile device to access our online help.

• Go to https://help.vtechphones.com/vm928hd or

https://help.vtechphones.com/vm928-2hd; OR

• Scan the QR code on the right. Launch the camera app or QR code scanner app

on your smartphone or tablet. Hold the device’s camera up to the QR code and

frame it. Tap the notiﬁcation to trigger the redirection of the online help.

- If the QR code is not clearly displayed, adjust your camera’s focus by moving

your device closer or further away until it is clear.

You can also call our Customer Support at 1 (800) 595-9511 [in US] or

1 (800) 267-7377 [in Canada] for help.

NOTESNOTE

• The rechargeable battery in the parent unit is built-in.

• Use only the power adapters supplied with this product.

• Make sure the parent unit and the baby unit are not connected to

the switch controlled electric outlets.

• Connect the power adapters in a vertical or ﬂoor mount position

only. The adapters’ prongs are not designed to hold the weight of

the parent unit and the baby unit, so do not connect them to any

ceiling, under-the-table, or cabinet outlets. Otherwise, the adapters

may not properly connect to the outlets.

• Make sure the parent unit, the baby unit and the power adapter

cords are out of reach of children.

• To maintain compliance with the FCC’s RF exposure guidelines,

place the baby unit at least 20cm from nearby persons.

Speciﬁcations are subject to change without notice.

05/22. VM928-XHD_QSG_V2.

VM928HD

VM928-2HD

Full Color Pan and Tilt

HD Video Monitor

Go to www.vtechphones.com

to register your product for enhanced

warranty support and the latest VTech

product news.

1 Connect the baby monitor

Power on or off the baby monitor

What’s in the box

Status check

Once you power on both your

baby unit and parent unit, your

parent unit displays image from

the baby unit, and the LINK LED

light turns on.

The green LED light of the

baby unit turns on.

3 Positioning the baby monitor

Caution

• The default volume of your parent unit is level

3, and the maximum volume is level 5. If you

experience high-pitched screeching noise from

your baby monitor while positioning:

- Make sure your baby unit and parent unit are

more than 3 feet (1 meter) apart, OR

- Lower the volume of your parent unit.

NOTESNOTE

Note

• To avoid interference from other electronic

devices, place your baby monitor at least 3 feet

(1 meter) away from devices such as wireless

routers, microwaves, cell phones and computers.

Use the menu

Press MENU to enter the menu, choose a

menu item, or save a setting. You can use

the parent unit for advanced settings or

operations, such as to play or stop the baby

unit lullaby, or to adjust the baby unit sound

sensitivity.

While in the menu:

• Press , , or to scroll among the

menu options.

• Press SELECT to select an item, or to save

a setting.

• Press TALK to return to the live video.

• Press to go to the Help & info page.

Basic operation - Parent unit

Overview - Parent unit

Overview - Baby unit

Frequency control Crystal controlled PLL synthesizer

Transmit frequency Baby unit: 2.405-2.475GHz

Channels 32

LCD 5’’ Color LCD

(IPS 1280x720 pixels)

Nominal effective range Maximum power allowed by FCC and IC. Actual operating range may vary

according to environmental conditions at the time of use.

Power requirements Parent unit: 3.7V 5000mAh, 18.5Wh Lithium-ion battery

Baby unit power adapter: Output: 5V DC @ 1A

Parent unit power adapter: Output: 5V DC @ 2A

Technical specications

Important safety instructions

1LINK LED light

2 LED light

33- level sound indicator

light

• Press to zoom in/out.

• When in the main menu,

press to go to the

Help & Info page.

5TALK

• Press and hold to talk to

the baby unit.

• While in a submenu,

press to exit.

6Arrow keys

7MENU/SELECT

• Press to enter the main

menu.

• While in a menu, press to

choose an item, or save a

setting.

8- VOL/ VOL +

• Increase or decrease

parent unit’s volume.

9Microphone

10 Antenna

11 Speaker

12 POWER key

13 Power jack

14 RESET

• Force reboot the parent

unit.

15 Stand

1Microphone

2Camera lens

3Light sensor

4LED indicator

5Infrared LEDs

6 ON/OFF switch

7Antenna

8Speaker

9Temperature sensor

• Position the sensor horizontally for

its optimal usage.

10 Power jack

11 Threaded socket for wall mounting

12 Pair button

1 set for VM928HD

2 sets for VM928-2HD

Need help?

Parent unit icons

Main menu

Monitoring mode (For VM928-2HD only)

• Baby unit 1 in Single mode

• Baby unit 2 in Single mode

• Patrol mode

• Split mode

Melodies and soothing sounds

Melodies and Soothing Sounds

• Select play all melodies, or play one of the

ﬁve melodies and four soothing sounds.

Timer

• You can also set the timer to stop playing

after 15, 30 or 60 minutes, or playing non-

stop.

Alerts - Sound, motion and temperature

Sound

• Select sound Sensitivity level.

• Turn on/off Sound Detection Alert.

• Turn on/off Auto Wake Up function.

(See Sound Detection and Auto Wake Up

section)

Motion

• Turn on/off Motion Alert.

• Select motion Sensitivity level.

(See Motion Detection section)

Main menu

Temperature

• Turn on/off Temperature Alert.

Set the parent unit to beep whenever the

room temperature detected by the baby

unit falls outside of the set temperature

range.

• Select Minimum temperature for alert

range.

• Select Maximum temperature for alert

range.

• Select temperature Format.

Set temperature display in Fahrenheit (oF)

or Celsius (oC ).

Parent unit settings

• Adjust parent unit screen Brightness.

• Turn on/off Dim Mode.

Baby unit settings

• Turn on/off baby unit’s Status LED.

• Select Field of View.

Choose Wide angle or Standard .

• Adjust baby unit’s speaker Volume.

General settings

• Turn on/off Low Battery Alert Tone.

Set the parent unit to beep when the

battery is low.

• Turn on/off No Link Alert Tone.

Set the parent unit to beep when the link

between the parent unit and the baby unit

is lost.

Main menu icons

VM928HD

VM928-2HD

Quick start guide VM928HD VM928-2HD

For more support information

x 2

Quick start guide

Strangulation

Hazard

Keep this cord out of reach of children.

The cord needs to be at least three feet

away from the child at all times. Do not

use with an extension cord. Do not

remove this tag.

Éloignez ce cordon des enfants. Le

cordon doit se trouver à au moins trois

pieds d’un enfant et ce, en tout temps.

N’utilisez pas de rallonge. Ne retirez pas

cette étiquette.

Mantenga este cable fuera de la alcance

de los niños. Este cable debe estar por

lo menos tres pies fuera de la alcance

del niño en todo momento. No lo use

con una extensión inalámbrica. No quite

esta etiqueta.

Risque

d’étranglement

Riesgo de

estrangulación

Charge the parent unit battery before use

When you have connected and

turned on the parent unit, the battery

will be charged automatically.

NOTESNOTE

Notes

• Before using the baby monitor for the

ﬁrst time, charge the parent unit battery

for 12 hours. When the parent unit

battery is fully charged, the battery icon

becomes solid .

• It takes longer to charge the battery

when the parent unit is turned on. To

shorten the charging time, turn the

parent unit off while charging.

• The standby time varies depending on

the sensitivity level you set, your actual

use and the age of the battery.

The battery icon indicates the battery status (see the following table).

Battery indicators Battery status Action

The screen displays .

The light ﬂashes.

The battery has very little

charge and may be used for

only a short time.

Charge

without interruption

(about

30 minutes).

The battery icon becomes

solid .

The battery is fully charged. To keep the battery charged, connect

it to AC power when not in use.

Slide the switch to ON to power on

your baby unit. After the parent unit is fully charged,

press POWER until the welcoming

screen appears.

Raise the parent unit antenna

for better reception

Connect the baby monitor (Cont’d)

> 3ft (1m)

< 3m

> 3m

≥

< 3ft (1m)

3ft (1m)

Adjust speaker volume

Press - VOL/ VOL + to adjust your parent unit

speaker volume. It determines the volume of

sound transmitted from your baby unit.

Zoom

Press to zoom in or out.

Talk to your baby via the baby unit

1. Press and hold the TALK key.

2. When the icon displays on screen,

speak to your parent unit. Your voice is

transmitted to the baby unit.

3. When ﬁnish talking, release

the TALK key and hear your baby again.

Press and hold

Turn on/off the parent unit screen

You can turn on or off the parent unit

screen without powering off the parent

unit. You can still hear sound from the

baby unit.

• Press POWER on the parent unit to

turn off the screen.

• Press any keys on the parent unit to

turn on the screen again.

Current view status

• The baby unit number that is being viewed

when in:

-Single CAM mode.

-Patrol mode (* For VM928-2HD only).

-Split mode (* For VM928-2HD only).

Split mode

(* For VM928-2HD only)

Patrol mode

(* For VM928-2HD only)

Night vision feature is activated automatically.

Motion alert is turned on.

Sound detection alert is turned on.

Melodies or soothing sound are turned on.

Parent unit speaker is muted.

Temperature alert is turned on.

Status icons

Alert icons

• Displays when parent unit’s battery is low

and needs charging.

• Displays when motion is detected at a baby

unit.

• Displays when sound is detected at a baby

unit.

• Baby unit detects temperature exceeds the

set maximum.

• Baby unit detects temperature is lower than

the set minimum.

The applied nameplate is located at the bottom of the baby unit’s

base.

When using your equipment, basic safety precautions should

always be followed to reduce the risk of ﬁre, electric shock and

injury, including the following:

1. Follow all warnings and instructions marked on the product.

2. Adult setup is required.

3. CAUTION: Do not install the baby unit at a height above 2

meters.

4. This product is intended as an aid. It is not a substitute for

responsible and proper adult supervision and should not be

used as such.

5. This product is not intended for use as a medical monitor.

6. Do not use this product near water. For example, do not use

it next to a bath tub, wash bowl, kitchen sink, laundry tub or

swimming pool, or in a wet basement or shower.

7. CAUTION: Use only the battery provided. There may be a risk

of explosion if a wrong type of battery is used for the parent

unit. The battery cannot be subjected to high or low extreme

temperature and low air pressure at high altitude during use,

storage or transportation. Disposal of battery into ﬁre or a hot

oven, or mechanically crushing or cutting or the battery can

result in an explosion. Leaving the battery in an extremely

high temperature surrounding environment can result in an

explosion or the leakage of ﬂammable liquid of gas. Battery

subjected to extremely low air pressure may result in an ex-

plosion or the leakage of ﬂammable liquid or gas. Dispose of

used battery according to the information in The RBRC seal.

8. Use only the adapters included with this product. Incorrect

adapter polarity or voltage can seriously damage the product.

Power adapter information:

Baby Unit Output: 5V DC 1A

VTech Telecommunications Ltd.

Model: VT05EUS05100

Parent Unit Output: 5V DC 2A

VTech Telecommunications Ltd.

Model: VT07EUS05200

Rechargeable battery information:

3.7V 5000mAh, 18.5Wh Lithium-ion Battery

Zhuhai Great Power Energy Co., Ltd.

Model: GSP806090-5Ah-3.7V-1S1P

9. The power adapter is intended to be correctly oriented in a

vertical or ﬂoor mount position. The prongs are not designed

to hold the plug in place if it is plugged into a ceiling, un-

der-the-table or cabinet outlet.

10. For pluggable equipment, the socket-outlet (power adapter)

shall be installed near the equipment and shall be easily

accessible.

11. Unplug this product from the wall outlet before cleaning.

Do not use liquid or aerosol cleaners. Use a damp cloth for

cleaning.

12. Do not cut off the power adapters to replace them with other

plugs, as this causes a hazardous situation.

13. Do not allow anything to rest on the power cords. Do not

install this product where the cords may be walked on or

crimped.

14. This product should be operated only from the type of power

source indicated on the marking label. If you are not sure of

the type of power supply in your home, consult your dealer or

local power company.

15. The equipment is to be supplied from an identiﬁed USB port

complying with the requirements of Limited Power Source.

16. Do not overload wall outlets or use an extension cord.

17. Do not place this product on an unstable table, shelf, stand or

other unstable surfaces.

18. This product should not be placed in any area where proper

ventilation is not provided. Slots and openings in the back or

bottom of this product are provided for ventilation. To protect

them from overheating, these openings must not be blocked

by placing the product on a soft surface such as a bed, sofa

or rug. This product should never be placed near or over a

radiator or heat register.

19. Never push objects of any kind into this product through

the slots because they may touch dangerous voltage points

or create a short circuit. Never spill liquid of any kind on the

product.

20. To reduce the risk of electric shock, do not disassemble this

product, but take it to an authorized service facility. Opening

or removing parts of the product other than speciﬁed access

doors may expose you to dangerous voltages or other risks.

Incorrect reassembling can cause electric shock when the

product is subsequently used.

21. You should test the sound reception every time you turn on

the units or move one of the components.

22. Periodically examine all components

for damage.

23. There is a very low risk of privacy loss when using certain elec-

tronic devices, such as baby monitors, cordless telephones,

etc. To protect your privacy, make sure the product has never

been used before purchase, reset the baby monitor period-

ically by powering off and then powering on the units, and

power off the baby monitor if you will not use it for some time.

24. Children should be supervised to ensure that they do not play

with the product.

25. The small parts of this monitor can be swallowed by babies or

small children. Keep these parts out of reach of children.

26. The product is not intended for use by persons (including

children) with reduced physical, sensory or mental capabili-

ties, or lack of experience and knowledge, unless they have

been given supervision or instruction concerning use of the

appliance by a person responsible for their safety.

SAVE THESE INSTRUCTIONS

Cautions

• Use and store the product at a temperature between 32oF and

104oF.

• Burn hazard, ﬁre hazard, explosion hazard associated with

mishandling of the battery.

• Do not expose the product to extreme cold, heat or direct

sunlight. Do not put the product close to a heating source.

• Warning—Strangulation Hazard—

Children have STRANGLED in cords. Keep this

cord out of the reach of children (more than 3 ft

(0.9m) away). Do not remove this tag.

• Never place the camera unit(s) inside the baby’s

crib or playpen. Never cover the camera unit(s)

or parent unit with anything such as a towel or a blanket.

• Other electronic products may cause interference with your

camera unit. Try installing your camera unit as far away from

these electronic devices as possible: wireless routers, radios,

cellular telephones, intercoms, room monitors, televisions,

personal computers, kitchen appliances and cordless tele-

phones.

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless devices):

Wireless Technology Research, LLC (WTR), an independent

research entity, led a multidisciplinary evaluation of the

interference between portable wireless devices and implanted

cardiac pacemakers. Supported by the U.S. Food and Drug

Administration, WTR recommends to physicians that:

Pacemaker patients

• Should keep wireless devices at least six inches from the

pacemaker.

• Should NOT place wireless devices directly over the pacemak-

er, such as in a breast pocket, when it is turned ON.

WTR’s evaluation did not identify any risk to bystanders with

pacemakers from other persons using wireless devices.

Electromagnetic elds (EMF)

This VTech product complies with all standards regarding

electromagnetic ﬁelds (EMF). If handled properly and according

to the instructions in this user’s manual, the product is safe to be

used based on scientiﬁc evidence available today.

Strangulation

Hazard

Keep this cord out of reach of children.

The cord needs to be at least three feet

away from the child at all times. Do not

use with an extension cord. Do not

remove this tag.

Éloignez ce cordon des enfants. Le

cordon doit se trouver à au moins trois

pieds d’un enfant et ce, en tout temps.

N’utilisez pas de rallonge. Ne retirez pas

cette étiquette.

Mantenga este cable fuera de la alcance

de los niños. Este cable debe estar por

lo menos tres pies fuera de la alcance

del niño en todo momento. No lo use

con una extensión inalámbrica. No quite

esta etiqueta.

Risque

d’étranglement

Riesgo de

estrangulación

Night vision

The baby unit has infrared LEDs that allow

you to see your baby clearly at night or in

a dark room. When the baby unit being

viewed detects low light levels, the infrared

LEDs are switched on automatically. The

images from the baby unit are in black and

white, and appears on the screen.

Notes

• It is normal if you see a short white glare on

your parent unit screen as the baby unit is

adapting to the dark environment.

• When the infrared LEDs are on, the images are

in black and white. This is normal.

Tip

• Depending on the surroundings and other

interfering factors, like lightings, objects, colors

and backgrounds, the video quality may vary.

Adjust the baby unit’s angle or place the baby

unit at a higher level to prevent glare and

blurry display.

Mount the baby unit on dry wall (optional)

For VM928-2HD only

Select Patrol mode as your monitoring

mode to alternately view the image

from baby units and every

10 seconds.

Change different views - Patrol

Select Split mode as your monitoring mode to view the images

from both baby units at once.

Note

• While in Split mode, you can press or to highlight the view of the baby unit 1 or

baby unit 2 , and hear the sounds transmitted from the baby unit.

Change different views - Split

Sound Detection and Auto Wake UP

Sound activated screen and audio - Auto Wake Up

Adjust sound detection sensitivity

When Auto Wake Up is turned on,

the parent unit screen stays off to

save power when the baby unit

detects no sound.

Once the baby unit detects sounds

that are louder than the chosen

sound sensitivity level, the parent

unit screen and speaker turn on

automatically. The parent unit will

then turn off again after 50 seconds

of no sound detection.

NOTESNOTE

Notes

• If you have muted the parent unit

speaker, only the parent unit screen

will turn on when a sound is detected.

• If you have turned on Auto Wake

Up but turned off Sound Detection

Alert, the parent unit will wake up

when the baby unit detects sounds

that are louder than the chosen sound

sensitivity level.

You can turn on Sound Detection Alert and adjust the Sound Sensitivity to detect sounds

and turn on the parent unit while its screen is switched off or dimmed.

When the baby unit detects sounds that exceed certain levels, the parent unit screen will

turn on and the baby unit starts transmitting the sounds to the parent unit, and you can

see and hear your baby.

If you have turned on Sound Detection Alert, the parent unit beeps when the baby unit

detect sounds.

The RBRC seal on the lithium-ion battery indicates that VTech Communications, Inc. is voluntarily

participating in an industry program to collect and recycle these batteries at the end of their useful lives,

when taken out of service within the United States and Canada.

The program provides a convenient alternative to placing used lithium-ion batteries into the trash or

municipal waste, which may be illegal in your area.

VTech’s participation makes it easy for you to drop off the spent battery at local retailers participating in the program or

at authorized VTech product service centers. Please call 1 (800) 8 BATTERY® for information on Li-ion battery recycling and

disposal bans/restrictions in your area. VTech’s involvement in this program is part of its commitment to protecting our

environment and conserving natural resources.

The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks of Call2recycle, Inc.

What does this limited warranty cover?

The manufacturer of this VTech product, VTech

Communications, Inc. (“VTech”), warrants to the holder

of a valid proof of purchase (“Consumer” or “you”) that

the Product and all accessories provided by VTech in

sales package (“Product”) are free from material defects

in material and workmanship, pursuant to the following

terms and conditions, when installed and used normally

and in accordance with operating instructions. This limited

warranty extends only to the Consumer for Products

purchased and used in the United States of America and

Canada.

What will VTech do if the Product is not free from defects

in materials and workmanship during the limited warranty

period (“Materially Defective Product”)?

During the limited warranty period, VTech’s authorized

service representative will replace at VTech’s option,

without charge, a Materially Defective Product. If we choose

to replace the Product, we may replace it with a new or

refurbished Product of the same or similar design. VTech will

return replacement products to you in working condition.

VTech will retain defective parts, modules, or equipment.

Replacement of the Product, at VTech’s option, is your

exclusive remedy. You should expect the replacement to

take approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the product extends for

ONE (1) YEAR from date of purchase (90 days on products

purchased as Refurbished*). This limited warranty also

applies to replacement Products for a period of either (a)

90 days from the date the replacement Product is shipped

to you or (b) the time remaining on the original one-year

limited warranty (90-day limited warranty on products that

are purchased as Refurbished*). Whichever is longer.

*Refurbished products purchased from our online store

carry a 90-day replacement warranty.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident,

shipping or other physical damage, improper installation,

abnormal operation or handling, neglect, inundation,

ﬁre, water or other liquid intrusion; or

2. Product that has been damaged due to repair, alteration

or modiﬁcation by anyone other than an authorized

service representative of VTech; or

3. Product to the extent that the problem experienced is

caused by signal conditions, network reliability, or cable or

antenna systems; or

4. Product to the extent that the problem is caused by use

with non-VTech accessories; or

5. Product whose warranty/quality stickers, product serial

number plates or electronic serial numbers have been

removed, altered or rendered illegible; or

6. Product purchased, used, serviced, or shipped for repair

from outside the United States of America or Canada, or

used for commercial or institutional purposes (including

but not limited to Products used for rental purposes); or

7. Product returned without a valid proof of purchase (see

item 2 below); or

8. Charges for installation or set up, adjustment of customer

controls, and installation or repair of systems outside the

unit.

How do you get warranty service?

To obtain warranty service in the United States of America,

please visit our website at www.vtechphones.com or call

1 (800) 595-9511 for instructions regarding where to return

the Product.In Canada, go to phones.vtechcanada.com or

dial 1 (800) 267-7377.

NOTE: Before calling for service, please review the user’s

manual - a check of the Product’s controls and features

may save you a service call.

Except as provided by applicable law, you assume the risk

of loss or damage during transit and transportation and

are responsible for delivery or handling charges incurred

in the transport of Product(s) to the service location. VTech

will return replaced product under this limited warranty to

you, transportation, delivery or handling charges prepaid.

VTech assumes no risk for damage or loss of the Product

in transit.

What must you return with the Product to get warranty

service?

1. Return the entire original package and contents including

the Product to the VTech service location along with a

description of the malfunction or difﬁculty; and

2. Include a “valid proof of purchase” (sales receipt)

identifying the Product purchased (Product model) and

the date of purchase or receipt; and

3. Provide your name, complete and correct mailing

address, and telephone number.

Other limitations

This warranty is the complete and exclusive agreement

between you and VTech. It supersedes all other written

or oral communications related to this product. VTech

provides no other warranties for this product. The warranty

exclusively describes all of VTech’s responsibilities

regarding the product.

There are no other expressed warranties. No one is

authorized to make modiﬁcations to this warranty and you

should not rely on any such modiﬁcation.

State Law Rights: This warranty gives you speciﬁc legal

rights, and you also have other rights which vary from state

to state.

Limitations: Implied warranties, including those of ﬁtness for

a particular purpose and merchantantability (an unwritten

warranty that the product is ﬁt for ordinary use) are limited

to one year from date of purchase. Some states do not allow

limitations on how long an implied warranty lasts, so the

above limitation may not apply to you.

In no event shall VTech be liable for any indirect, special,

incidental, consequential, or similar damages (including,

but not limited to lost proﬁts or revenue, inability to use

the product, or other associated equipment, the cost of

substitute equipment, and claims by third parties) resulting

from the use of this product. Some states do not allow

the exclusion or limitation of incidental or consequential

damages, so the above limitation or exclusion may not

apply to you.

Please retain your original sales receipt as proof

of purchase.

This baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby monitor

is set up to comply with the energy-conserving standards right out of the box. Follow the instructions to install and charge

the battery. The CEC battery charging testing mode is activated while charging. Even if the parent unit is paired to baby

units, the CEC battery charging testing mode is activated while it is powered off and charging.

FCC Part 15

This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the

Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modiﬁcations to this equipment not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may

not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation.

To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed

by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with

the FCC criteria. The baby unit shall be installed and used such that parts of all persons’ body are maintained at a distance of

approximately 8 in (20 cm) or more. The transmitter and antenna of the parent unit shall be held at least 1 in (2.5 cm) from your

face.

This Class B digital apparatus complies with Canadian requirement:

CAN ICES-3 (B)/NMB-3(B)

Industry Canada

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development

Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause

interference. (2) This device must accept any interference, including interference that may cause undesired operation of the

device.

The term ‘’IC:‘’ before the certiﬁcation/registration number only signiﬁes that the Industry Canada technical speciﬁcations were

met.

This product meets the applicable Innovation, Science and Economic Development Canada technical speciﬁcations.

RF radiation exposure statement

The baby unit complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The baby unit should

be installed and operated with a minimum distance of 8 in (20 cm) between the baby unit and all persons’ body. Use of other

accessories may not ensure compliance with FCC RF exposure guidelines. This transmitter must not be co-located or operating

in conjunction with any other antenna or transmitter. This equipment complies also with Industry Canada RSS-102 with respect

to Canada’s Health Code 6 for Exposure of Humans to RF Fields.

The RBRC seal For cETL compliance only Limited warranty

California Energy Commission battery

charging testing mode

FCC and IC regulations

10s

The parent unit display will dim to conserve energy after 5 minutes of inactivity, in

which there is neither key pressed nor alert received from the baby unit.

Dim mode

5 minute inactivity

Press any buttons

Sound

Sensitivity

level

Level 3

(Highest)

Level 2

(Medium)

Level 1

(Lowest)

Description The parent unit screen and

speaker turn on for very

small sounds, including

background noises from

your baby’s room.

The parent unit screen and

speaker turns on for loud

babbling and louder sounds

from your baby. The parent

unit remains quiet when your

baby makes soft sounds.

The parent unit screen

and speaker turn on for

loud crying or screeching

sounds from your baby.

The parent unit remains

quiet when your baby

makes soft sounds.

1. Place the wall mount bracket on a wall and then use

a pencil to mark the top and the bottom holes as

shown. Remove the wall mount bracket and drill

two holes in the wall (7/32 inch drill bit).

NOTESNOTE

Notes

• Check for reception strength and baby unit’s angle before drilling the holes.

• The types of screws and anchors you need depend on the composition of the wall. You may need to purchase the screws and anchors separately to mount your baby units.

2. If you drill the holes into a stud, go to step 3.

• If you drill the holes into an object other than a stud, insert the wall

anchors into the holes. Tap gently on the ends with a hammer until the

wall anchors are ﬂush with the wall.

3. Align the wall mount bracket and screws with the

holes in the wall as shown. Tighten the screw in the

middle hole ﬁrst, so that the wall mount bracket

position is ﬁxed. You can tighten the other screw in

the top hole.

3. Insert the screws into the holes and tighten the screws until only 1/4 inch

of the screws are exposed.

4. Place the baby unit on the wall mount bracket.

Tighten the screw into the threaded socket

at the bottom to secure the baby unit. Align

the holes on the wall mount bracket with the

screws on the wall, and slide the wall mount

bracket down until it locks into place.

5. You can maximize your baby unit’s viewing angles by tilting the wall mount bracket.

Hold the baby unit, and then rotate the knob in anticlockwise direction. This will loosen the joint of the wall mount bracket.

Tilt your baby unit up or down to adjust to your preferred angle. Then, rotate the knob in clockwise direction to tighten the joint and

secure the angle.

4. Place the baby unit on the wall mount bracket.

Tighten the screw into the threaded socket at the

bottom to secure the baby unit.

Motion Detection

Adjust motion detection sensitivity

You can turn on Motion Alert and adjust the Motion Sensitivity to detect motions and

turn on the parent unit while its screen is switched off or dimmed.

When the baby unit’s camera detects motions that exceed certain levels, the parent unit

screen will turn on and the baby unit starts transmitting the sounds to the parent unit, and

you can see and hear your baby.

If you have turned on Motion Alert, the parent unit beeps when the baby unit detects

motions.

Motion

Sensitivity

level

Level 3

(Highest)

Level 2

(Medium)

Level 1

(Lowest)

Description The parent unit screen and

speaker turn on for small

motions, such as yawning or

stretching.

The parent unit screen and

speaker turns on for normal

daily motions, such as

people walking around the

house.

The parent unit screen and

speaker turn on for large

motions, such as children

are chasing or jumping

around.

Monitoring mode

Change different views - Single CAM

Select baby unit 1 or baby unit 2 to

view the image from the baby unit.

Below are the questions most frequently asked about the baby monitor.

Why does the baby

monitor not respond

normally?

Try the following (in the order listed) for common cure:

1. Disconnect the power to the baby units and the parent unit.

2. Wait a few seconds before connecting power back to the baby units and the parent unit.

3. Turn on the baby units and the parent unit.

4. Wait for the parent unit to synchronize with the baby units. Allow up to one minute for

this to take place.

Why don’t the lights of

the baby unit and parent

unit go on when I switch

on the units?

Perhaps the parent unit’s battery is depleted. Insert the appliance plug into the parent

unit and put the adapter in a wall socket. The parent unit will establish connection with

the baby unit.

Perhaps the baby unit is not connected to the power. Insert the appliance plug into the

baby unit and put the adapter in a wall socket. Then, slide the ON/OFF to switch on the

baby unit and to establish connection with the parent unit.

Why doesn’t my parent

unit charge while

connected to AC power?

Make sure the power is not controlled by a wall switch.

Why is my screen in black

and white?

The screen is in black and white during night-time or in a dark room when the night

vision feature is activated. This is normal.

Why do I get glare or

blurry display on my

screen when viewing my

baby at night?

During night-time or in a dark room, the surroundings and other interfering factors,

like lightings, objects, colors and backgrounds may affect the image quality on your

parent unit screen. Adjust the baby unit’s angle or place the baby unit at a higher level to

prevent glare and blurry display.

Why does the baby

monitor produce a

high-pitched noise?

The parent unit and baby units may be too close to each other.

• Move the parent unit away from the baby units until the noise stops; OR

• Turn down the volume of your parent unit.

Why does the parent unit

beep?

The baby units may be out of range. Move the parent unit closer to the baby units (but

not less than 3 feet).

The parent unit may not have enough charge for the parent unit to perform normally.

Charge the battery in the parent unit until the battery icon becomes solid .

The temperature of your baby’s room may be too high or too low.

Why don’t I hear a sound/

Why can’t I hear my baby

cry?

The parent unit speaker volume may be too low. Press VOL+ to increase the volume, or

use the parent unit menu to change sound sensitivity level to the highest level.

Why can’t I establish a

connection? Why is the

connection lost every now

and then? Why are there

sound interruptions?

The baby units may be out of range. Move the parent unit closer to the baby units (but

not less than 3 feet).

Other electronic and wireless products may cause interference with your baby monitor.

Try installing your baby monitor as far away from these devices as possible.

If you power on only one baby unit, your parent unit may display Make sure baby unit X

is on or move closer to baby unit X, and the LINK LED light ﬂashes. Switch to the baby unit

you have powered on via menu.

Frequently asked questions

Mesures de sécurité importantes

La plaque signalétique appliquée est située au bas du socle de l’unité

du bébé.

Lorsque vous utilisez votre appareil, vous devriez toujours suivre

certaines mesures de précaution de base aﬁn de réduire les risques

d’incendie, d’électrocution et de blessures corporelles, dont ceux qui

suivent:

1. Observez toutes les instructions et mises en garde inscrites sur

l’appareil.

2. L’installation par un adulte est requise.

3. MISE EN GARDE: N’installez pas l’unité du bébé à une hauteur

supérieure à 2 mètres.

4. Ce produit a été conçu pour être un dispositif d’appoint seulement.

Il n’est pas le remplacement d’une supervision responsable et

adéquate par un adulte et ne devrait pas être utilisé comme telle.

5. Ce produit n’est pas conçu pour être utilisé en tant que moniteur

médical.

6. N’utilisez pas cet appareil près de l’eau ni de toute autre source

d’humidité, par exemple, près d’une baignoire, cuve à lessive,

évier de cuisine, dans un sous-sol humide ni près d’une piscine,

dans un soussol humide ou une douche.

7. MISE EN GARDE: Utilisez uniquement la pile fournie. Un risque

d’explosion pourrait survenir si un mauvais type de pile est utilisé

pour l’unité du parent. La pile ne peut pas être soumise à des

températures extrêmes élevées ou basses et à une faible pression

d’air à haute altitude pendant l’utilisation, l’entreposage ou le

transport. L’élimination de la pile dans le feu ou dans un four chaud,

ou l’écrasement ou le découpage mécanique de la pile peuvent

entraîner une explosion. Laisser la pile dans un environnement à

température extrêmement élevée peut entraîner une explosion

ou la fuite d’un liquide ou d’un gaz inﬂammable. Une pile soumise

à une pression d’air extrêmement basse peut provoquer une

explosion ou une fuite de liquide ou de gaz inﬂammable. Éliminer

la pile usagée conformément aux informations du Sceau RBRC.

8. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation

d’un adaptateur dont la polarité ou la tension serait inadéquate

risque d’endommager sérieusement le produit et mettre votre

sécurité en péril.

Informations sur les adaptateurs électriques :

Adaptateur de l’unité du bébé: Sortie : 5 V CC 1A.

VTech Telecommunications Ltd.

Modèle : VT05EUS05100

Adaptateur de l’unité du parent: Sortie : 5 V CC 2A.

VTech Telecommunications Ltd.

Modèle : VT07EUS05200

Informations sur les piles rechargeables :

3.7V 5000mAh, 18.5Wh Lithium-ion Battery

Zhuhai Great Power Energy Co., Ltd.

Modèle : GSP806090-5Ah-3.7V-1S1P

9. Lorsqu’ils sont branchés dans une prise de courant, les adaptateurs

secteur ont été conçus pour être orientés correctement, soit à la

verticale ou au plancher. Les broches n’ont pas été conçues pour

supporter le poids du bloc d’alimentation et le maintenir en place

si celuici est branché dans une prise au plafond, sous une table ou

dans un meuble.

10. Pour les appareils raccordés, la prise de courant (de l’adaptateur

secteur) doit être installée près de l’équipement et doit être

facilement accessible.

11. Débranchez ce produit de la prise de courant avant de procéder

au nettoyage. N’utilisez pas de nettoyants en aérosols. Utilisez un

chiffon humide pour le nettoyer.

12. Ne coupez pas les cordons d’alimentation pour remplacer les

ﬁches, car ceci peut présenter un danger potentiel.

13. Ne laissez aucun objet reposer ni appuyer sur le cordon

d’alimentation. N’installez pas cet appareil dans un endroit où

l’on risque d’écraser le cordon d’alimentation ou de le piétiner.

14. Ne faites fonctionner cet appareil qu’avec le type d’alimentation

indiqué sur l’étiquette. Si vous ne connaissez pas le type

d’alimentation que vous possédez à votre domicile, consultez votre

marchand ou votre compagnie locale d’électricité.

15. L’équipement doit être fourni à partir d’un acquiescement gauche

identiﬁé d’USB aux conditions de la source d’énergie limitée.

16. Ne surchargez pas les prises de courant murales ni les rallonges

électriques.

17. Ne placez pas cet appareil sur un chariot, meuble, trépied, support

de montage ni table chancelants.

18. Les trous et ouvertures du boîtier, situés à l’arrière de l’appareil

ou sous celui-ci, servent à aérer l’appareil. Pour l’empêcher de

surchauffer, ne bloquez sous aucun prétexte ces ouvertures

et n’empêchez pas l’aération adéquate de l’appareil en le

plaçant sur un lit, divan, tapis ou toute autre surface similaire.

De même, ne le positionnez pas à proximité ni au-dessus d’une

source de chaleur ou d’un calorifère. De plus, ne placez pas

l’appareil dans un endroit avant de vous assurer qu’il y ait une

bonne circulation d’air.

19. N’enfoncez jamais d’objets à travers les ouvertures de cet appareil,

car ils pourraient entrer en contact avec des points de tension

dangereux ou causer des courts-circuits qui peuvent dégénérer

en incendies ou en risques d’électrocution. Ne renversez jamais

de liquide dans ce produit.

20. Aﬁn de réduire les risques d’électrocution, ne démontez pas cet

appareil, mais apportez-le dans un centre de service autorisé.

L’ouverture du boîtier ou le retrait de toutes pièces que contient

cet appareil, à l’exception de l’accès autorisé à certaines portes

ou ouvertures, risque de vous exposer à des points de tension

dangereux ou d’autres dangers. Un remontage incorrect peut par

la suite présenter des risques d’électrocution.

21. Vous devriez tester la réception chaque fois que vous mettez

l’appareil en fonction.

22. Examinez les composantes aﬁn de vériﬁer si celles-ci ne sont pas

endommagées.

23. Il existe un très faible risque de perte de conﬁdentialité avec

certains appareils électroniques (autres écoute-bébés, téléphones

sans ﬁls etc.). Pour l’éviter, s’assurer que le produit n’a jamais été

utilisé avant l’achat, réinitialiser l’unité de façon périodique, éteindre

l’écoute-bébé quand il n’est pas en cours d’utilisation.

24. Les enfants devraient être supervisés aﬁn de vous assurer qu’ils ne

jouent pas avec l’appareil.

25. Les petites pièces de ce moniteur peuvent être avalées par les

bébés ou les petits enfants. Veuillez tenir ces pièces hors de

portée des enfants.

26. Le produit n’est pas conçu pour être utilisé par des personnes

(incluant des enfants) aux capacités physiques, sensorielles

ou mentales réduites ou qui manquent d’expérience et de

connaissances, à moins qu’on leur ait donné sufﬁsamment de

supervision ou d’instructions relativement à l’utilisation de l’appareil

par une personne responsable de leur sécurité.

CONSERVEZ CES INSTRUCTIONS

Mises en garde

• Utilisez et entreposez le produit à une température entre 0˚ C

(32˚F) et 40˚C (104˚ F).

• Risque de brûlure, risque d’incendie, risque d’explosion associé à

une mauvaise manipulation de la batterie.

• N’exposez pas cet appareil à des froids ou des chaleurs extrêmes,

ainsi qu’à la lumière directe du soleil. Ne l’installez pas près d’une

source de chauffage.

• Avertissement - Risque de strangulation

- Les enfants se sont ÉTRANGLÉS dans des cordons.

Gardez ce cordon hors de portée des enfants (à

plus de 0,9 m). N’enlevez pas cette étiquette.

• Ne jamais placer le moniteur à l’intérieur du berceau ou du parc

de bébé. Ne jamais couvrir le moniteur ou l’unité (s) portative avec

un article tel une serviette ou une couverture.

• D’autres produits électroniques peuvent causer des interférences

auprès de votre caméra IP. Essayez d’installer votre caméra IP le

plus loin possible de ces dispositifs électroniques : routeurs sans ﬁl,

radios, téléphones cellulaires, interphones, moniteurs de pièces,

téléviseurs, ordinateurs personnels, appareils électriques de cuisine

et téléphones sans ﬁl.

Stimulateurs cardiaques implantés dans l’organisme

Les simulateurs cardiaques (ne s’applique qu’aux dispositifs

numériques sans ﬁl):

L’organisme ‘Wireless Technology Research, LLC (WTR)’, une ﬁrme

de recherche indépendante, a mené une évaluation pluridisciplinaire

des interférences entre les téléphones sans ﬁl portatifs et les

stimulateurs cardiaques implantés dans l’organisme. Appuyée par

l’Administration des aliments et drogues (FDA) des États-Unis, la ﬁrme

WTR recommande aux médecins:

Avis aux détenteurs de stimulateurs cardiaques

• Vous devriez maintenir les dispositifs sans ﬁl à au moins six pouces

du simulateur cardiaque.

• Ils ne doivent PAS placer le téléphone sans ﬁl directement sur le

stimulateur cardiaque, tel que dans une poche de chemise, lor-

sque celui-ci est en marche.

L’étude effectuée par l’organisme WRS n’a pas identiﬁé de risque

pour les détenteurs de simulateurs cardiaques causés par les gens qui

utilisent dispositifs sans ﬁl à proximité de ceux-ci.

Champs électromagnétiques (EMF)

Ce produit de VTech est conforme à toutes les normes se rapportant

aux champs électromagnétiques (EMF) standard. Si vous le manipulez

correctement en suivant les instructions de ce guide, son utilisation

sera sécuritaire pendant de nombreuses années, selon les meilleures

évidences scientiﬁques dont nous disposons aujourd’hui.

CABLE MANAGEMENT

1 2 3

VTech VM928HD Guide de démarrage rapide

Marque: VTech

Modèle: VM928HD

Catégorie: Moniteurs vidéo bébé

Taper: Guide de démarrage rapide

Télécharger le PDF

rapport

dans d''autres langues

English: VTech VM928HD Quick start guide

VTech VM928HD Guide de démarrage rapide

VTech VM928HD Guide de démarrage rapide

dans d''autres langues

Documents connexes