Sharp SCH3043GB Manuel utilisateur

SCH3043GB
Sharp
Marque
Sharp
Modèle
SCH3043GB
Taper
Manuel utilisateur

Ce manuel convient également à

Induction Cooktop: Models SCH2443GB, SCH3043GB
OPERATION MANUAL
INDUCTION COOKTOP
MODELS : SCH2443GB, SCH3043GB
E
E
E
E
E
TINSEB589MRR0 E
APR 28, 2022
US CUSTOMER ASSISTANCE .................................................. 2
CANADA CUSTOMER ASSISTANCE ...........................................3
US CONSUMER LIMITED WARRANTY .......................................4
CANADA CONSUMER LIMITED WARRANTY .................................5
IMPORTANT SAFETY INSTRUCTIONS ........................................ 6
COOKING SAFETY ...............................................................................6
CLEANING SAFETY ..............................................................................6
ENVIRONMENT OF UNIT .................................................................... 6
SERVICE AND REPAIR SAFETY ........................................................... 7
UNPACKING AND EXAMINING YOUR COOKTOP ................................ 7
PRODUCT DISPOSAL .......................................................................... 7
BEFORE USING THE COOKTOP ................................................ 8
INDUCTION COOKTOP CHARACTERISTICS ........................................ 8
COOKWARE .........................................................................................8
COOKTOP NOISE ................................................................................. 9
COOKTOP FEATURES ......................................................... 10
MODELS ............................................................................................10
CONTROL PANEL............................................................................... 10
COOKTOP WORKSTATION SIDE ACCESSORIES
(NOT INCLUDED WITH ALL MODELS)...............................................11
USING THE COOKTOP ........................................................ 12
CONTROL LOCK ................................................................................. 12
OPERATING THE INDUCTION HEATERS ........................................... 12
POWER CONTROL ............................................................................. 12
AUTOMATIC POWER LEVEL CONTROL ............................................. 12
POWER BOOST .................................................................................12
AUTOMATIC SETTINGS .....................................................................13
1. WARM ........................................................................................... 13
2. SIMMER ....................................................................................... 13
3. MELT .............................................................................................13
BRIDGE HEATER ...............................................................................13
PAUSE ...............................................................................................14
AUTO TURN OFF ................................................................................14
TIMER ...............................................................................................14
OBJECT DETECTED OVER KEYPAD INDICATOR ................................ 14
HOT SURFACE INDICATOR ................................................................ 14
COMPATIBLE COOKWARE ................................................... 15
PROPER COOKWARE ........................................................................ 15
IMPROPER COOKWARE ....................................................................15
CLEANING AND CARE ........................................................ 16
DO NOT USE THE FOLLOWING TO CLEAN YOUR UNIT ..................... 16
METAL MARKS AND SCRATCHES ..................................................... 16
SUGARY SPILLS, MILK, TOMATO-BASED PRODUCTS,
MELTED PLASTICS OR HEAVILY BURNED-ON RESIDUE ..................16
SPECIFICATION ................................................................ 17
HEAT SETTING DISPLAY ................................................................... 17
BEFORE YOU CALL ............................................................ 18
2E
E
E
E
E
E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
CUSTOMER ASSISTANCE UNITED STATES ONLY
REGISTER YOUR PRODUCT
Registering your new product is easy and offers benets that help you get the most
out of your Sharp product including:
9Convenience: Ifyoueverneedwarrantysupport,yourproductinformationisalreadyonle.
9Communication:StayuptodatewithimportantnoticationsandspecialoffersfromSHARP.
9Support: Quickly access support content including Owner’s Manuals, FAQ’s,
 How-toVideos,andmuchmore.
3 EASY WAYS TO REGISTER TODAY!
PRODUCT SUPPORT
If you have questions about the setup or operation of your product, please refer to
the corresponding section within this manual.
Additionally, visit www.sharpusa.com/support to access exclusive content about your
product including:
ÆFAQ’s and How-To Videos
ÆFind or Request Service
ÆPurchase an Extended Warranty
ÆDownloads including the Installation Guide, Spec Sheet, and Owner’s Manual
CONTACT US
If at any time you have questions or comments concerning your SHARP product,
please contact the SHARP Customer Assistance Center. We are available to
assist you through multiple contact methods for your convenience:
Scan this QR Code on your mobile device Visit http://www.sharpusa.com/register
ONLINE
Visit our sites to
learn more about
your product at
sharpusa.com and
sbl.sharpusa.com
See the Contact Us section on our sites U.S. | www.sharpusa.com/support Contact a Sharp Advisor on the phone
Contact a Sharp Advisor on the phone
CALL US
US 800-BE-SHARP
800-237-4277
Mon-Fri: 7am-7pm CST
Sat-Sun: 9am-7pm CST
CALL US
US 800-BE-SHARP
800-237-4277
Mon-Fri: 7am-7pm CST
Sat-Sun: 9am-7pm CST
EMAIL
Available 24/7
US: sharpusa.com
CHAT ONLINE
Mon-Fri: 7am-7pm CST
Sat-Sun: 9am-7pm CST
SCAN
Use the camera or
QR code scanning
application on your
mobile device
US CUSTOMER ASSISTANCE
E3
E
E
E
E
E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
CUSTOMER ASSISTANCE CANADA ONLY
To aid in answering questions if you call for service or for reporting loss or theft,
please use the space below to record the model and serial number located on the
back side of the unit.
Model Number:
Serial Number:
Date of Purchase:
Dealer Name:
Address:
City:
Province:
Postal Code:
Telephone:
PRODUCT SUPPORT
If you have questions about the setup or operation of your product, please refer to
the corresponding section within this manual.
Additionally, visit www.sharp.ca to access exclusive content about your product
including:
ÆFind a Dealer
ÆFind Service Locations
ÆDownloads including the Installation Guide, Spec Sheet, and Owner’s Manual
CONTACT US
If at any time you have questions or comments concerning your SHARP product,
please contact the SHARP Customer Assistance Center. We are available to
assist you through multiple contact methods for your convenience:
https://sharp.ca/contact-sharp CA | www.sharp.ca Contact a Sharp Advisor on the phone
CALL US
CA 877-278-6709
Mon-Fri: 8am-5pm EST
(except statutory holidays)
EMAIL
Available 24/7
See the Contact Us
section on our site.
SUPPORT SITE
Product Downloads,
Service Locator, Where
to Buy, Toner Recycling
Program and more.
CANADA CUSTOMER ASSISTANCE
US CONSUMER LIMITED WARRANTY
4E
E
E
E
E
E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
SHARP ELECTRONICS CORPORATION (“Sharp”) warrants to the rst consumer purchaser (“Purchaserˮ) that this SHARP brand
product (“Productˮ), when shipped in its original container and sold or distributed in the United States by Sharp or an authorized
Sharp dealer or reseller, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair
the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the Purchaser for
parts or labor for the period(s) set forth below.
This limited warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below
nor to any Product the exterior of which has been damaged or defaced, which has been subjected to misuse, abnormal service or
handling, or which has been altered or modied in design or construction.
In order to enforce the rights under this limited warranty, the Purchaser should follow the steps set forth below and provide proof of
purchase to the servicer.
The limited warranty described herein is in addition to whatever implied warranties may be granted to Purchasers by law. ALL
IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE
LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not allow limitations
on how long an implied warranty lasts, so the above limitation may not apply to you.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein,
or to extend the duration of any warranties beyond the time period described above on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive
remedy available to the Purchaser. Correction of defects, in the manner and for the period of time described herein, shall constitute
complete fulllment of all liabilities and responsibilities of Sharp to the Purchaser with respect to the Product, and shall constitute
full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event shall Sharp be liable,
or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed
by anyone other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incident or consequential
economic or property damage. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion
may not apply to you.
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND
PUERTO RICO.
Your product model number &
description
Model # SCH2443GB, SCH3043GB or Induction Cooktops.
(Be sure to have this information available when you need service for your Product.)
Warranty period for this product: One (1) year parts and labor including in-home service.
Product must be accessible to provide service.
Additional item(s) excluded from
warranty coverage (if any):
Non-functional accessories, service calls to your home to instruct how to use your induction
cooktop appliance, replace or repair house fuses or to correct house wiring, improper com-
mercial use, installation, or maintenance, damage to the product caused by delivery, accident,
modications, re, oods or acts of God.
Where to obtain service: From a Sharp Authorized Servicer located in the United States. To nd the location of the
nearest Sharp Authorized Servicer, call Sharp toll free at 1-800-237-4277 (1-800-BE-SHARP).
What to do to obtain service: In-home service is provided for one year from date of purchase. In-home service can be arranged
by calling 1-800-BE-SHARP. Be sure to have Proof of Purchase available.
TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP or visit www.sharpusa.com.
SAVE THE PROOF OF PURCHASE AS IT IS NEEDED SHOULD YOUR APPLIANCE EVER REQUIRE WARRANTY SERVICE.
CANADA CONSUMER LIMITED WARRANTY
Congratulations on your purchase!
Sharp Electronics of Canada Ltd. (“Sharp”) warrants to the rst purchaser for this Sharp brand product (“Product”), when shipped
in its original container and sold or distributed in Canada by Sharp or by an authorized Sharp dealer, and Product was not sold “as
is” or “sales nal” that the Product will during the applicable warranty period, be free from defects in material and workmanship,
and will within the applicable warranty period, either repair the defective Product or provide the rst purchaser a replacement of the
defective Product.
This warranty does not apply to any appearance items of the product nor to the additional excluded item(s) set forth below nor to any
product the exterior of which has been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal
service or handling, which has been altered or modied in design or construction, or if the serial number or model number afxed to
Product has been removed, defaced, changed, altered or tampered with.
How to get service: Should this Sharp product fail to operate during the warranty period, warranty service is provided by an Authorized
Sharp Service Centre or an Authorized Sharp Servicing Dealer. In home warranty service will be carried out to locations accessible
by on-road service vehicle and within 50 km of an authorized Sharp service centre. The servicer may if necessary take the unit for
repair at the servicer's facility. No other person (including any Sharp dealer or service centre) is authorized to extend, enlarge or
transfer this warranty on behalf of Sharp.
The express warranties in this limited warranty are, except for consumer purchasers domiciled in Quebec, in lieu of and, except to the
extent prohibited by applicable law, Sharp disclaims all other warranties and conditions, express or implied, whether arising by law,
statute, by course of dealing or usage of trade, including, without limitation, implied warranties or conditions of merchantability and/or
quality, tness for a particular use or purpose, and/or non-infringement. Limitations (not applicable to consumer purchasers domiciled
in Quebec to the extent prohibited under Quebec law): (a) Sharp shall not be liable for any incidental, special, consequential, economic,
exemplary or indirect damages of any kind or nature (including lost prots or damages for loss of time or loss of use or loss of data)
arising from or in any connection with the use or performance of a Product or a failure of a Product, even if Sharp is aware of or has
been advised of the possibility of such damages; (b) the remedies described in this limited warranty constitute complete fulllment
of all obligations and responsibilities of Sharp to the purchaser with respect to the Product and shall constitute full satisfaction of all
claims, whether based on contract, negligence, strict liability or otherwise. Some provinces may not allow the exclusion or limitation
of certain damages, or limits on the duration or voiding of implied warranties or conditions; in such provinces, the exclusions and
limits herein may not apply. This limited warranty is, except for consumer purchasers domiciled in Quebec, governed by the laws of
the Province in Canada in which the purchaser has purchased the Product. For consumer purchasers domiciled in Quebec this limited
warranty is governed by the laws of Quebec.
Your product model number &
description
Model # SCH2443GB, SCH3043GB or Induction Cooktops.
(Be sure to have this information available when you need service for your Product.)
Warranty period for this product: One (1) year parts and labor including in-home service.
Product must be accessible to provide service.
Additional item(s) excluded from
warranty coverage (if any):
Non-functional accessories, service calls to your home to instruct how to use your induction
cooktop appliance, replace or repair house fuses or to correct house wiring, improper com-
mercial use, installation, or maintenance, damage to the product caused by delivery, accident,
modications, re, oods or acts of God.
To obtain the name and address of the nearest Authorized Sharp Service Centre or Dealer, please contact:
SHARP ELECTRONICS OF CANADA LTD 335 Britannia Road East
Mississauga, Ontario
L4Z 1W9
(905) 568-7140
Website: www.sharp.ca
SAVE THE PROOF OF PURCHASE AS IT IS NEEDED SHOULD YOUR APPLIANCE EVER REQUIRE
WARRANTY SERVICE.
THIS LIMITED WARRANTY IS VALID ONLY IN CANADA
E5
E
E
E
E
E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
6E
E
E
E
E
E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
IMPORTANT SAFETY INSTRUCTIONS
Read all instructions carefully before installation and operation.
Keep manuals for future reference. The appliance is manufac-
tured in compliance with the relevant safety standard.
WARNING Failure to follow these warnings could result in
a re or explosion causing property damage, personal injury or
death. To reduce the risk of re, electric shock or injury, use
only as intended and take the following precautions.
INTENDED USE
• This appliance is designed for built-in household use only.
• Do not use outdoors.
• Do not use the appliance to heat a room.
SAFETY INSTRUCTIONS
1 Proper Installation - Be sure your appliance is properly
installed and grounded by a qualied technician.
2 Never Use Your Appliance for Warming or Heating the
Room.
3 Do Not Leave Children Alone - Children should not be left
alone or unattended in an area where the appliance is in use.
They should never be allowed to sit or stand on any part of
the appliance.
4 Wear Proper Apparel - Loose tting or hanging garments
should never be worn while using the appliance.
5 User Servicing - Do not repair or replace any part of the appli-
ance unless specically recommended in the manual. All
other servicing should be referred to a qualied technician.
6 Storage in or on Appliance - Flammable materials should
not be stored in an oven or near surface units.
7 Do Not Use Water on Grease Fires - Smother re or ame
or use dry chemical or foam type extinguisher.
8 Use Only Dry Potholders - Moist or damp potholders on
hot surfaces may result in burns from steam. Do not let
potholders touch hot heating elements. Do not use towel or
other bulky cloth.
SURFACE COOKING UNITS
1 Remove all packaging labels and protective lm before
operating the cooktop.
2 Use Proper Pan Size - This appliance is equipped with surface
units of different sizes. Select utensils having at bottoms
large enough to cover the surface unit heating element. The
use of undersize utensils will expose a portion of the heat-
ing element to direct contact and may result in ignition of
clothing. Proper relationship of utensil to burner will also
improve efciency.
3 Never Leave Surface Units Unattended at High Heat Set-
tings - Boil over causes smoking and greasy spillovers that
may ignite.
4 Glazed Cooking Utensils - Only certain types of glass, glass/
ceramic, ceramic earthenware, or other glazed utensils are
suitable for range top service without breaking due to sudden
change in temperature.
5 Utensil Handles Should Be Turned Inward and Not Extended
Over Adjacent Surface Units - To minimize burns, ignition
of ammable materials, and spillage due to unintentional
contact with the utensil, the handle of a utensil should be
positioned so that it is turned inward and does not extend
over adjacent surface units.
6 CAUTION Do not store items of interest to children in
cabinets above cooktop - children climbing on the range to
reach items could be seriously injured.
7 DO NOT TOUCH SURFACE UNITS OR AREAS NEAR
UNITS - Surface units may be hot even though they are dark
in color. Areas near surface units may become hot enough
to cause burns. During and after use, do not touch, or let
clothing of other ammable materials contact surface units
or areas near units until they have had sufcient time to cool.
Among these areas are (identication of area - for example,
the cooktop, surfaces facing the cooktop, etc.).
8 Do Not Cook on Broken Cooktop - If cooktop should break,
cleaning solutions and spillovers may penetrate the broken
cooktop and create a risk of electric shock. Contact a quali-
ed technician immediately.
9 Clean Cooktop with Caution - If a wet sponge or cloth is
used to wipe spills on a hot cooking area, be careful to avoid
steam burn. Some cleaners can produce noxious fumes if
applied to a hot surface.
10 Do not allow aluminum foil, paper or cloth to come in contact
with an Induction Heater.
11 Do not prepare food in aluminum foil or plastic containers
over hot cooking zones.
12 Do not use aluminum foil to line cooking heater, drip trays or
oven bottoms, except as suggested in the manual. Improper
use of liners may result in a risk of electric shock or re.
13 Do not allow pans to boil dry or empty. Never leave the
cooktop unattended when in use.
14 Always remove the covers on sealed or canned goods before
heating to avoid eruption.
15 Do not touch hot surfaces. Use dry pot holders to hold the
handles of pots and pans.
16 Use only dry potholders. Damp potholders on hot surfaces
may cause steam that results in burns. Do not let potholders
touch the hot Induction Heater. Do not use towels or bulky
cloth.
17 When the unit is on, only touch the control panel, as the
cooktop surface may be hot. The cooktop surface will
remain hot for a short period of time after use. Do not touch
hot surfaces.
INDUCTION COOKTOP SURFACE
UNITS
Do not place metallic objects such as knives, forks, spoons and
lids on the cooktop surface since they can get hot.
E7
E
E
E
E
E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
GLASS/CERAMIC COOKING SURFACES
1 Do Not Cook on Broken Cook-Top - If cook-top should
break, cleaning solutions an spillovers may penetrate the
broken cook-top and create a risk of electric shock. Contact
a qualied technician immediately.
2 Clean Cook-Top With Caution – If a wet sponge or cloth is
used to wipe spills on a hot cooking area, be careful to avoid
steam burn. Some cleaners can produce noxious fumes if
applied to a hot surface.
CLEANING SAFETY
CAUTION Clean cooktop with caution. If a wet sponge or
cloth is used to wipe spills on a hot cooking area, be careful to
avoid steam burns. Some cleaners can produce steam or noxious
fumes if applied to a hot surface.
Do not use steam cleaners or high-pressure cleaners to clean the
cooktop, as this may result in electric shock.
ENVIRONMENT OF UNIT
IMPORTANT
1 To reduce the risk of re, do not let any objects obstruct the
inlet and outlet of the unit.
2 To reduce the risk of electric shock, do not mount unit over a sink.
3 To reduce the risk of re, do not store anything directly on top
of the appliance surface when the appliance is in operation.
4 Always have a working smoke detector in or near the kitchen.
5 Do not leave lids other metal objects such as knives, forks
or spoons on the cooktop. If the cooktop is turned on, these
objects can heat up quickly and may cause burns.
6 Do not place rough or uneven objects that may damage the
surface on the unit. If the cooktop is near a window, ensure
curtains do not blow over or near the unit.
7 Do not use the cooktop as a work surface. Certain substances
such as salt, sugar or sand can scratch the ceramic glass
surface.
8 Do not store hard, pointed or heavy objects that may fall
over the cooktop.
9 Do not put detergents or ammable materials in the equip-
ment installed under the cooktop.
10 Use extreme caution when moving a utensil containing hot
oil or other hot liquids.
11 Any spilled fat or oil on the cooktop may ignite when the
cooktop is hot.
12 Do not use accessories not recommended by the manufac-
turer. Items with magnetic elds (such as radios, televisions,
credit cards, cassette tapes, etc.) may affect the unit. The
marked electrical rating should be at least as great as the
electrical rating on the appliance.
13 To prevent accidents and achieve optimal ventilation, allow
for sufcient space around the cooking area.
14 Use proper cookware size. This appliance is equipped with
four cooking zones of different sizes. Choose cookware with
a at bottom large enough to cover the unit heating surface.
The use of undersized cookware will expose a portion of the
hot heater and may cause burning.
15 To reduce risk of burns, ignition of ammable materials
and spillage due to unintentional contact with cookware,
cookware handles should be turned inward and not extend
over adjacent heating surface.
16 Wear proper apparel. Loose tting or hanging garments
should never be worn while using the appliance.
SERVICE AND REPAIR SAFETY
WARNING Do not repair or replace any part of the appliance
unless specically recommended in the manual. There are no
user serviceable parts on this appliance. All services should be
referred to a qualied technician.
Only an authorized service representative should attempt to
service your cooktop.
UNPACKING AND EXAMINING YOUR
COOKTOP
CONDITION OF UNIT
WARNING Do not operate any appliance with a damaged
cord or after the appliance malfunctions or has been damaged in
any manner. Return appliance to the nearest authorized service
facility for examination, repair or adjustment.
IMPORTANT Do not cook on a broken cooktop. If the cooktop
breaks, cleaning solutions and spillovers may penetrate the
broken cooktop and create a risk of electric shock.
PRODUCT DISPOSAL
This product may not be disposed of as household waste. It must
be delivered to the applicable collection point for the recycling
of electrical and electronic equipment. Inappropriate waste
handling of this product may have negative consequences for the
environment and human health. For more detailed information
about recycling of this product, please contact your local city
ofce, your household waste disposal service or the shop where
you purchased the product.
8E
E
E
E
E
E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
BEFORE USING THE COOKTOP
INDUCTION COOKTOP
CHARACTERISTICS
Induction cooking is a safe, advanced, efcient and economical
cooking technology. It works by electromagnetic eld generat-
ing instant heat directly to the cookware bottom, rather than
indirectly through heating the ceramic glass surface.
CAUTION The Cooking Zones may appear to be cool while
turned ON and after they have been turned OFF. The ceramic
glass surface may be HOT from residual heat transferred from
the cookware that can cause burns.
PAN DETECTION
The induction system automatically detects each heating area in
a safe condition for use and detects suitable cookware placed in
each Cooking Zone to eliminate accidental operation.
COOKWARE SIZE DETECTION
The cookware recognition system automatically detects and
adapts the Cooking Zones power level to the cookware sizes
in use.
EFFICIENT
Induction cooking heats faster while using less energy. Water
boils quickly with induction power levels.
COOKWARE
USING COMPATIBLE COOKWARE
The cookware recognition system used in each Cooking Zone
requires the use of cookware made with magnetic material to
start the heating process on any of the Cooking Zones.
When purchasing utensils, look for cookware with the Induction
Compatible Symbol on the retail box. Check that the bases of
your cookware are attracted by a magnet to nd out if they are
suitable.
Heavy, high-quality stainless steel cookware is always recom-
mended to use on your Induction Cooktop surface.
If the base of the cookware is only partially magnetic, only the
magnetic area will heat. Heat may not be distributed evenly. The
non-magnetic area may not heat up to a sufcient temperature
for cooking.
SELECTING SURFACE COOKING COOKWARE
The cookware used with the Induction Cooktop should have at
bottoms that make good contact with the entire surface of the
Induction Heater. Check for atness by rotating a ruler across
the bottom of the cookware. Be sure to follow all the recom-
mendations for using cookware. Use cookware made with the
correct material for Induction Cooking.
PROPER COOKWARE MATERIAL
Proper cookware for your cooktop is at-bottomed pots or pans
with or made from the following:
• Magnetic stainless steel
• Cast iron
• Enameled iron
• Nickel
NOTE: Some cookware can produce noises when used on
induction cooking zones. This is not a fault in the cooktop, and
its function will not be impaired in any way as a result.
IMPROPER COOKWARE MATERIAL
Do not use cookware on your cooktop with or made from the
following:
• Non-magnetic stainless steel
• Bottom measuring less than 4.7" (120 mm) on left heaters
and right front heater
• Bottom measuring less than 5.7" (145 mm) on right rear
heater
• Pot with stands
• Heat resistant glass
• Ceramic
• Copper
• Aluminum
ATTENTION:
• Use quality cookware with heavy bottoms for better heat
distribution allowing for more even cooking results.
• Use appropriate pan size for the food being cooked.
• Do not let pans boil dry. This may cause permanent damage
in the form of breakage, fusion or marring that can affect
the ceramic glass cooktop. (This type of damage is not
covered by your warranty.)
• Do not use dirty pans with grease buildup.
Even quality cookware can scratch the cooktop surface,
especially if cookware is slid over the ceramic glass cooktop
surface without being lifted. Over time, sliding ANY type of
cookware over the ceramic cooktop will likely alter the overall
appearance of the cooktop. Eventually the buildup of scratches
will make cleaning the surface difcult and degrade the overall
appearance of the cooktop.
DO NOT SLIDE COOKWARE across the cooktop surface.
Doing so may permanently damage the appearance of the
ceramic cooktop.
CAUTION DO NOT TOUCH HOT COOKWARE directly
with hands. Always use oven mitts or pot holders to protect
hands from burns.
E9
E
E
E
E
E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
BEFORE USING THE COOKTOP
COOKWARE RECOMMENDATIONS
Follow these recommendations for using cookware:
CORRECT
• Cookware centered correctly on Induction Heater surface.
• Flat pan bottom and straight sides.
• Pan size meets or exceeds the recommended minimum size
for the Induction Heater.
• Pan rests completely on the cooktop surface.
• Pan is properly balanced.
WRONG
• Cookware not centered on Induction Heater surface.
• Curved or warped pan bottoms or sides.
• Pan does not meet the minimum size required for the Cooking
Zone used.
• Pan bottom rests on cooktop trim or does not rest completely
on the cooktop surface.
• Heavy handle tilts pan.
NOTE: ANY one of the incorrect conditions listed may be
detected by the cookware recognition system used in each
cooking zone. If the cookware does not meet correct conditions,
one or more of the Induction Heaters may not heat. (Failure to
heat is indicated by a ashing power level in the digital display
for the affected heater.)
USE THE CORRECT COOKWARE SIZE
The Induction Heaters available on the Induction Cooktop
require a MINIMUM pan size to be used at each location.
COOKWARE SIZE
GUIDE min
max
±1/2” (1.6 cm)
Induction Heater outer line
The thick outer line at each Induction Heater is helpful to
determine the MINIMUM cookware size and the MAXIMUM
cookware size. After centering the cookware on the cooktop,
make sure the cookware covers 1/2" inside of the thick outer line
and does not extend more than 1/2" beyond the thicker line on
the Induction Heater. The pan must make FULL contact on the
ceramic glass surface without the bottom of the pan touching
the metal cooktop trims.
NOTE: Pan bottom should not exceed 1/2" (13 mm) from outer
Induction Heater.
If a pan made of the correct material is centered properly on any
of the active Induction Heaters but is TOO SMALL, the power
level will ash in the digital display and the pan will not heat.
COOKTOP NOISE
The induction elds are generated by electronic equipment,
which produces heat at a high power level. A soft-sounding cool-
ing fan runs when the unit is running multiple cooking zones.
Sounds may be produced by different types of cookware, such as:
• Clicking noise may be heard at low power settings. This is
due to the magnetic elds in use and is considered normal
operation.
• The operational noises may be different with various cook-
ware used on the cooktop.
• Light-weight stainless steel pans may make noise or vibrate.
Heavy-weight quality cookware is recommended.
• Cookware with irregular or warped bottoms can vibrate
audibly on the ceramic glass surface at high power settings.
• Cracking noise may be heard if the cookware base is made
of layer of different material.
• Low humming noise is normal at high power settings.
• If multiple cooking zones are used simultaneously at high
power settings with cookware made with a layer of different
material, whistling can occur.
• Loose-tting handles on cookware can vibrate slightly.
• High-quality cast iron and enamel cookware is less likely to
vibrate or produce noise.
10E
E
E
E
E
E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
COOKTOP FEATURES
MODELS
This manual covers different models. The cooktop you have purchased may have some or all of the features listed.
SCH2443GB
(24" Model)
SCH3043GB
(30" Model)
1 32 4
6
1 3 52 4
6
1 Left Rear heater
2 Left Front heater
3 Right Rear heater
4 Right Front heater
5 Cooling Zone
6 Serial/Model number label
(underneath the cooktop)
CONTROL PANEL
SCH2443GB & SCH3043GB
12
12 1313 1312 1313 13
14 12 13 14 1314 14 1412 12 12
Numbers next to the Control Panel illustration indicate pages on
which there are feature descriptions and usage information.
E11
E
E
E
E
E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
COOKTOP FEATURES
COOKTOP WORKSTATION SIDE ACCESSORIES
(MODEL SKR00A7FS)
Your cooktop is also a workstation with the inclusion of our
kitchen grade stainless-steel Cooling Zone (8" x 21") and Spoon
Rest (6" x 21") with two drip trays. The side accessories can
attach magnetically on either edge of the cooktop to secure in
place, attach magnetically to each other on a single side of the
cooktop or stand on the adjacent counter (rubber feet protect
countertop surfaces).
The Cooling Zone provides a location to set hot cookware after
removing from the Cooking Zone or the oven.
The Spoon Rest lets you rest cooking utensils while protecting
your countertop from stains and drips. The Spoon Rest includes
two removable drip trays for easy cleaning after food preparation.
All items are dishwasher-safe (upper or lower rack).
EASY ATTACHMENT
ARRANGE SOLO
ARRANGE AS YOU LIKE
SPOON REST
COOLING ZONE
12E
E
E
E
E
E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
USING THE COOKTOP
CONTROL LOCK
Control Lock may be activated when the cooktop heaters are
in use or when they are inactive. If Control Lock is active when
a heater is in use, only the Heater ON/OFF keypad will be
operational.
TO LOCK
Touch and hold the LOCK keypad until a tone sounds. The
letter L will blink for 3 seconds in each Heater display, then the
displays will clear. Only the Heater ON/OFF keypads will be
operational. If any other keypads are touched, the display will
blink and alternate between L and the power level to indicate
the keypad controls are locked.
TO UNLOCK
Touch and hold LOCK keypad again until a tone sounds. The
letter L will blink in each Heater display for 3 seconds then
disappear.
OPERATING THE INDUCTION HEATERS
TURN ON AN INDUCTION HEATER
Select a heater and use the corresponding keypad to operate.
1 Place a compatible pot or pan on the desired Induction Heater.
2 Touch the ON/OFF keypad to turn the heater ON. A tone will
sound and the number 0 will display, indicating no power
level has been set.
3 Use the + and – keypads to select desired power level. Set
a power level between 1–9 or Power Boost (P) within 10
seconds, or the heater will automatically turn OFF.
NOTE:
If compatible cookware is not detected on the Induction Heater
when the heater is turned ON, the display will blink and
the heater will automatically turn OFF after 15 seconds of
inactivity.
TURN OFF AN INDUCTION HEATER
Select the desired heater to turn OFF and touch the ON/OFF
keypad until a tone sounds and the displayed power level is
cleared.
STANDARD SETTINGS
SETTING LEVELS TYPE OF COOKING
High 9-P Bring liquid to a boil. Always reduce
setting to a lower heat when liquids begin
to boil or foods begin to cook.
Medium
High
7-8 Brown meat, heat oil for deep fat frying
or continue a rapid boil.
Medium 5-6 Maintain a simmer or slow boil, thicken
sauces and gravies.
Medium
Low
3-4 Continue cooking covered foods, steam
foods or maintain foods at a warm
temperature before serving.
SETTING LEVELS TYPE OF COOKING
Low 1-2 Melt butter or chocolate.
NOTE: Standard heat settings can be used to melt, warm and
simmer. Each heater has presets for more temperature control
for each of these cooking functions.
POWER CONTROL
Power level may be increased or decreased during cooking by
using the + and – keypads.
If power level is 9, pressing + again will turn on Power Boost
and the letter P will display.
If power level is 0, pressing – again will turn power level to 9.
There are ten power levels: power levels 1–9 and Power Boost.
Power Boost uses maximum power for 10 minutes, indicated
on the display as P.
A tone will sound each time a power level is increased or
decreased using the + and – keypads.
Holding the + keypad will quicken the speed at which power
levels increase until level 9 is reached. Touch the + keypad once
more to select P for Power Boost. Once P is set, touching the +
keypad will not increase the power level further.
Holding the – keypad will quicken the speed at which power
levels decrease until level 0 is reached. If the – keypad is touched
again, power level 9 will display. If a power level greater than
0 is not set within 10 seconds, the heater will automatically
tur n OFF.
NOTE: The unit is equipped with safeguards against parching
during cooking. When unit is used for high temperature cook-
ing, such as frying, stir-frying and grilling, heating will appear
intermittent.
AUTOMATIC POWER SHARING
CONTROL
The power of the complete induction hob is limited to 7500W.
The power of each pair of heaters is limited to 3500W. The unit
will automatically limit the power of each pair of heaters. When
a high power level is selected on one heater, the power level
on the other heater is reduced so the total power of the pair of
heaters does not exceed the limit.
POWER
LEVEL
MAXIMUM ALLOWABLE POWER
LEVEL FOR OTHER HEATER
5P
P5
98
89
8 8
E13
E
E
E
E
E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
USING THE COOKTOP
POWER BOOST
Use Power Boost to cook at maximum power for a short period
of time. Power Boost is only recommended for bringing water
to a boil.
Touch the – keypad to reduce power level to level 9. After 10
minutes of Power Boost, the power level automatically reduces
to level 9. When Power Boost expires and the level reduces to 9,
a tone will sound and the digital display will switch from P to 9.
WARNING Do not leave unit unattended while Power Boost
or other high power settings are in use.
AUTOMATIC SETTINGS
The Induction Cooktop has 3 preset cooking functions: Warm,
Simmer and Melt.
1. WARM
Warm will maintain temperature of 150ºF for up to 5 hours
before automatically turning OFF.
TURN WARM ON
1 Place a compatible pot or pan on the desired heater and
touch the ON/OFF keypad to turn heater ON. A tone will
sound and the number 0 will display, indicating no power
level has been set.
2 Touch the SIMMER/WARM keypad once. A tone will sound
and the letter A and the word WARM will display.
TURN WARM OFF
• Touch the ON/OFF keypad to turn the heater OFF.
OR
• Touch the + or – keypads to increase or decrease power level
to deactivate the Warm function. A tone will sound and the
letter A and the word WARM will clear from the display.
NOTE: If SIMMER/WARM is pressed when Warm is in use,
the heater function will automatically switch to Simmer.
2. SIMMER
Simmer will maintain temperature of 195ºF for up to 5 hours
before automatically turning OFF.
TURN SIMMER ON
1 Place a compatible pot or pan on the desired heater and
touch the ON/OFF keypad to turn heater ON. A tone will
sound and the number 0 will display, indicating no power
level has been set.
2 Touch the SIMMER/WARM keypad twice. A tone will
sound and the letter A and the word SIMMER will display.
TURN SIMMER OFF
• Touch the ON/OFF keypad to turn the heater OFF.
OR
• Touch the + or – keypads to increase or decrease power level
to deactivate the SIMMER function. A tone will sound and the
letter A and the word SIMMER will clear from the display.
NOTE: If SIMMER/WARM is pressed when Simmer is in use,
heater function will automatically switch to Warm.
3. MELT
Melt will maintain temperature of 105ºF for up to 5 hours before
automatically turning OFF.
TURN MELT ON
1 Place a compatible pot or pan on the right rear (24" model)
or middle rear (30" model) heater and turn the heater ON.
A tone will sound and power level 0 will display, indicating
no power level has been set.
2 Touch the MELT keypad. A tone will sound and the letter A
and the word MELT will display.
TURN MELT OFF
• Touch the ON/OFF keypad to turn the heater OFF.
OR
• Touch the + or – keypads to increase or decrease power level to
deactivate the Melt function. A tone will sound and the letter
A and the word MELT will clear from the display.
BRIDGE HEATER
The left front and left rear heaters can be synced to accommodate
larger cookware, such as a 9" x 18" griddle specically designed
for use with ceramic glass cooktops.
TO TURN BRIDGE ON
1 Place compatible cookware, such as a griddle, on the left
front and left rear Induction heaters.
2 Touch the ON/OFF keypad to turn either of the heaters ON.
A tone will sound and 0 will display on the selected heater.
3 Touch the BRIDGE keypad to sync the two heaters. A tone
will sound and the number 0 and the word BRIDGE will
display for both heaters.
4 Use + and – keypads to select desired power level. Either
heater’s keypad may be used to control the settings. If a power
level is not set within 10 seconds, the BRIDGE function will
automatically turn OFF, and the heaters will no longer be
synced. The heaters will remain ON however, and power
levels may be set or turned OFF individually.
TO TURN BRIDGE OFF
Touch the BRIDGE keypad to deactivate the BRIDGE function.
After 10 seconds a tone will sound and both heaters will show
power level 0 and the word BRIDGE will clear from the displays.
NOTE: Each heater must be turned OFF separately after the
BRIDGE function has been deactivated. Touch the ON/OFF
keypad to turn each heater OFF.
PAUSE
Pause may be used to temporarily stop all cooking functions
and timers for up to 10 minutes without erasing settings. To use
the Pause function, at least one heater or timer must be in use.
When the cooktop operation is paused, all controls are locked
automatically except the heaters’ ON/OFF keypad.
14E
E
E
E
E
E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
PAUSE COOKING/TIMER
Touch the PAUSE ALL keypad for 1 second. A tone will sound
and the displayed settings for each heater/timer in use will blink.
RESUME COOKING TIMER
Touch the PAUSE ALL keypad for 1 second. A tone will sound,
indicating cooking or timer operations have resumed, and
displayed settings for each heater/timer in use will remain on.
NOTE: If the PAUSE ALL keypad is not touched again within
10 minutes to resume cooking/timer operation, the heaters/
timers will automatically turn OFF.
AUTO TURN OFF
If a power level is not changed during operation, each heater
will power down a level once the time on the chart has elapsed.
POWER LEVEL POWER DOWN TIME
110 hours
25 hours
34 hours
44 hours
53 hours
62 hours
72 hours
82 hours
91 hour
P10 minutes
MELT 2 hours
WA R M 5 hours
SIMMER 5 hours
OBJECT DETECTED OVER KEYPAD
INDICATOR
If any objects are detected over the keypads for longer than 10
seconds, all heaters will automatically turn OFF and the displays
will blink . The will remain blinking in the displays until
objects are removed from the keypads.
TIMER
The automatic timer settings range from 1 minute to 99 minutes.
The nal minute will count down in seconds on the display.
POWER
LEVEL TIMER
IMPORTANT: The timers DO NOT control heaters or turn
them off at the end of the countdown.
TO SET THE TIMER
1 Select desired heater for timer to be set (compatible cookware
must be placed and power level must already be set) and touch
TIMER keypad. A tone will sound and the numbers 00 and
the word TIMER will blink on the display.
2 Touch the + and – keypads to set the desired countdown
time. A tone will sound each time a power level is increased
or decreased.
Holding the + key will increase the speed at which numbers
display until 99 is reached. The maximum number of minutes
that may be set is 99 minutes. If the + keypad is touched after
99 is displayed, timer input will not be changed.
To decrease a time input, touch the – keypad. Holding the –
keypad will increase the speed at which numbers display and
decrease until 00 is reached. If the – keypad is touched again,
99 minutes will be set.
Countdown time is accepted 5 seconds after the last + and –
keypad is touched. A tone will sound and the digits and word
TIMER will stop blinking and remain illuminated. If a time
greater than 00 is not set within 5 seconds of touching the
TIMER keypad, the Timer function will automatically turn OFF.
TO ADJUST THE TIMER DURING USE
Touch the TIMER keypad and use the + and – keypads to set
the new time.
TO CANCEL THE TIMER
1 Select designated timer to be canceled.
2 Touch and hold the TIMER keypad for 3 seconds. A tone
will sound and the digits and word TIMER will clear from
the display.
IMPORTANT: Canceling a timer DOES NOT TURN OFF
the heater in use.
HOT SURFACE INDICATOR
Heaters can remain hot after cooking has completed and the
cookware has been removed.
If the power level is set to 0 and the heater is still ON, the display
will blink and alternate between 0 and H to indicate residual
heat until the heater has cooled.
If the heater has been turned OFF, the display will blink H to
indicate residual heat until the heater has cooled.
WARNING In the event of a power failure to the home or to
the cooktop, be aware that SURFACES OF HEATERS WILL
REMAIN HOT even though the Hot Surface Indicator is not
displayed. The Hot Surface Indicator will not automatically
illuminate once power is restored.
USING THE COOKTOP
E15
E
E
E
E
E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
COMPATIBLE COOKWARE
PROPER COOKWARE
Proper cookware for your cooktop is at-bottomed pots or pans
with or made from the following:
• Magnetic stainless steel
• Cast iron
• Enameled iron
• Nickel
IMPROPER COOKWARE
Do not use pots and pans on your cooktop with or made from
the following:
• Non-magnetic stainless steel
• Bottom measuring less than 4.7" (12 cm)
• Pot with stands
• Heat resistant glass
• Ceramic
• Copper
• Aluminum
Look for cookware with this induction compat-
ibility symbol on the retail box.
To check if cookware is suitable for induc-
tion cooking, test if the base is attracted by
a magnet.
16E
E
E
E
E
E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
CLEANING AND CARE
After each use, ensure the controls are set to OFF and let your
cooktop cool down completely before cleaning your cooktop.
When it is cool to the touch, apply approximately 1 teaspoon
(5 ml) of non-abrasive cleaner with a lightly damp cloth to the
ceramic glass surface. Use a second cloth to remove any remain-
ing cleaner residue. Wipe dry with a dry cloth.
DO NOT USE THE FOLLOWING TO
CLEAN YOUR UNIT
• Glass cleaners containing ammonia or chlorine bleach, as
these materials may stain the cooktop
• Caustic cleaners that may etch the surface
• Abrasive cleaners
• Metal scouring pads and scrub sponges
• Powdery cleaners containing chlorine bleach
• Flammable cleaners, such as lighter uid or WD-40
NOTE: Sugary products can damage the ceramic glass surface.
If dry sugar, sugar syrup, tomato products or milk spills on
the surface during heating, clean the ceramic glass surface
immediately.
METAL MARKS AND SCRATCHES
1 Do not slide pots and pans across your cooktop. Sliding
cookware will leave metal markings on the cooktop surface.
These marks are removable using a ceramic glass cleaner
with cleaning pad for ceramic glass.
2 If pots with a thin overlay of aluminum or copper are allowed
to boil dry, the overlay may leave black discoloration on the
cooktop. Discoloration should be removed immediately before
heating again or the discoloration may be permanent.
WARNING DO NOT USE OR CLEAN DAMAGED
COOKTOP. If the cooktop should crack or break, do not use
or attempt to clean it. Turn off the appliance at the circuit breaker
or fuse box and call an authorized servicer.
SUGARY SPILLS, MILK, TOMATO-
BASED PRODUCTS, MELTED PLASTICS
OR HEAVILY BURNED-ON RESIDUE
Sugary spills (jellies, fudge, candy, syrups, etc.), milk, tomato-
based products, melted plastics or heavily burned-on residue
can cause pitting of the surface of your cooktop unless the spill
is removed while still hot. (Damage from pitting is not covered
by warranty.)
WARNING USE SPECIAL CARE WHEN REMOVING
SPILLS WHILE COOKTOP SURFACE IS HOT.
Remove these spills while the cooktop is still hot.
1 Turn off all heaters and remove all pans immediately.
2 Wearing an oven mitt, use a razor blade scraper at a 30˚ angle
against the ceramic glass surface and scrape from hot surface
to a cooler area.
3 Remove the spills with paper towels.
NOTE:
• Do not use a dull or nicked blade. Be sure to use a new, sharp
razor scraper.
• Do not use the razor blade for daily cleaning, as it may wear
the pattern on the glass.
If the ceramic glass surface of your cooktop is damaged by
pitting, it should be replaced.
E17
E
E
E
E
E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
SPECIFICATION
SCH2443GB (24") SCH3043GB (30")
Product dimension (w x d x h) inch 24" x 21" x 21/2" 30" x 21" x 21/2"
Cut-out dimension (w x d) inch 227/16" x 195/8"293/16" x 195/8"
Voltage (Volts/Amps) 208/240V/30A 208/240V/30A
Frequency 60 Hz 60 Hz
Tot al p ower 7,500W 7, 500W
Cooking Zones 4 4
Left Front/Boost 2,100W/3,500W 8.26" x 7.08" 2,100W/3,500W 8.26" x 7.08"
Left Rear/Boost 2,100W/3,500W 8.26" x 7.08" 2,100W/3,500W 8.26" x 7.08"
Bridge Left Front + Left Rear 3,300W Max 3,300W Max
Right Front/Boost 2,100W/3,500W 8.26" dia. 2,100W/3,500W 8.26" dia.
Right Rear/Boost 1,200W/1,800W 5.7" dia. 1,200W/1,800W 5.7" dia.
Simmer Enhancer Enabled All Heaters All Heaters
HEAT SETTING DISPLAY
DISPLAY DESCRIPTION
0No power level for the zone
1-9 Power Level
PPower Boost
H
Residual heat: a heater is still hot to the touch
H appears on the display when a cooking zone temperature is at or above 149ºF and clears
from the display when the cooking zone temperature has fallen to 131ºF.
0 H A heater is ON and set to power level 0.
F
(followed by a Number or Letter)
Error Code
(see Before You Call)
Blinking Display Heater and timer functions are PAUSED.
Blinking Display
Object detected over keypad.
Blinking Display
No cookware detected on heater.
A WARM Warm function
A SIMMER Simmer function
A MELT Melt function
18E
E
E
E
E
E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
BEFORE YOU CALL
If you encounter errors with the cooktop, check the guide below for common problems, causes and solutions to see if you can correct
the problem yourself before calling 1-800-BE-SHARP for assistance or service.
PROBLEM POSSIBLE CAUSE SOLUTIONS
The fans keep running for one minute
after the cooking zone has been switched
off
The electronics are cooling down This is a normal occurrence
Cooktop powers down Inactivity for 15 seconds with no
compatible cookware detected
See page 8 for Pan Detection
Noise like humming, crackling, clicking
or buzzing
This is a normal occurrence See page 9 for Cooktop Noise
Control keys not working Control lock may be activated See page 12 for Control Lock
Power Boost does not work No cookware found, improper place-
ment of cookware on the cooking zone
or improper cookware is being used
See page 8 for Proper Cookware and
Improper Cookware
F appears in the Power display Electronics fault error message of
particular cooking zone
See F0, F1, F2, F3, F4, F5, F6, F7, F8, F9,
Fc, FC, FE, FH, FJ, Ft
F0 appears in the Power display Microcontroller fault Refer to a qualied technician for service
F1 appears in the Power display Heater NTC short-circuit Refer to a qualied technician for service
F2 appears in the Power display Heater NTC open-circuit Refer to a qualied technician for service
F3 appears in the Power display Heat-sink NTC short-circuit Refer to a qualied technician for service
F4 appears in the Power display Heat-sink NTC open-circuit Refer to a qualied technician for service
F5 appears in the Power display Communication fault Refer to a qualied technician for service
F6 appears in the Power display Mains voltage zero crossing loss Refer to a qualied technician for service
F7 appears in the Power display Heater NTC unchanging Refer to a qualied technician for service
F8 appears in the Power display Heater NTC ADC fault Refer to a qualied technician for service
F9 appears in the Power display Fan error Refer to a qualied technician for service
Fc appears in the Power display User interface over-temperature 96°C Refer to a qualied technician for service
FC appears in the Power display Cap keys system fault Refer to a qualied technician for service
FE appears in the Power display User interface temperature sensor
short-circuit
Refer to a qualied technician for service
FH appears in the Power display EEPROM fault Refer to a qualied technician for service
Ft appears in the Power display User interface temperature sensor
open-circuit
Refer to a qualied technician for service
FJ appears in the Power display Mains over-voltage error Refer to a qualied technician for service
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
Surface de cuisson à induction: Modèles SCH2443GB, SCH3043GB
MANUEL D’UTILISATION
SURFACE DE CUISSON À INDUCTION
MODÈLES : SCH2443GB, SCH3043GB F
F
F
F
F
F
ASSISTANCE À LA CLIENTÈLE ................................................2
GARANTIE LIMITÉE DU CONSOMMATEUR AU CANADA ...................3
CONSIGNES DE SÉCURITÉ IMPORTANTES .................................. 4
SÉCURITÉ DE CUISSON ...................................................................... 4
SÉCURITÉ DE NETTOYAGE .................................................................. 4
ENVIRONNEMENT DE L’UNITÉ ...........................................................4
SÉCURITÉ DE RÉPARATION ET D’ENTRETIEN ....................................5
DÉBALLAGE ET VÉRIFICATION DE VOTRE SURFACE DE CUISSON .... 5
MISE AU REBUT DU PRODUIT ............................................................ 5
AVANT D’UTILISER LA SURFACE DE CUISSON .............................6
CARACTÉRISTIQUES DE LA SURFACE DE CUISSON À INDUCTION .... 6
USTENSILES DE CUISSON ..................................................................6
BRUIT PROVENANT DE LA SURFACE DE CUISSON ............................8
FONCTIONS DE LA SURFACE DE CUISSON ..................................9
MODÈLES ............................................................................................9
PANNEAU DE COMMANDE .................................................................. 9
PLAN DE TRAVAIL LATÉRAL POUR SURFACE DE CUISSON ............. 10
UTILISATION DE LA SURFACE DE CUISSON .............................. 11
VERROUILLAGE DES COMMANDES ..................................................11
FONCTIONNEMENT DES ÉLÉMENTS CHAUFFANTS À INDUCTION ..11
COMMANDES DE PUISSANCE ..........................................................11
COMMANDE DE NIVEAU DE PUISSANCE AUTOMATIQUE .................12
AMPLIFICATION DE LA PUISSANCE..................................................12
RÉGLAGES AUTOMATIQUES ............................................................. 12
1. RÉCHAUD (WARM) ....................................................................... 12
2. MIJOTER (SIMMER) .....................................................................12
3. FONDRE (MELT) ............................................................................ 12
CHAUFFAGE EN MODE PONT ...........................................................13
PAUSE ...............................................................................................13
ARRÊT AUTOMATIQUE ...................................................................... 13
TIMER (MINUTERIE) ......................................................................... 13
INDICATEUR D’OBJET SUR LE PAVÉ NUMÉRIQUE ...........................13
INDICATEUR DE SURFACE CHAUDE .................................................. 14
USTENSILES DE CUISSON COMPATIBLES ................................ 14
USTENSILES DE CUISSON APPROPRIÉS ......................................... 14
USTENSILES DE CUISSON NON APPROPRIÉS ................................. 14
NETTOYAGE ET ENTRETIEN ................................................. 15
NE PAS UTILISER LES PRODUITS SUIVANTS
POUR NETTOYER L’UNITÉ ................................................................. 15
MARQUES MÉTALLIQUES ET ÉGRATIGNURES .................................15
DÉVERSEMENTS DE SUCRE, DE LAIT, DE PRODUITS À BASE DE
TOMATE, DE PLASTIQUES FONDUS OU
DE RÉSIDUS TRÈS BRÛLÉS ..............................................................15
SPÉCIFICATION ................................................................ 16
AFFICHAGE DU RÉGLAGE DE CHALEUR ...........................................16
AVANT D’APPELER ............................................................ 17
F F F F F F F F F F
F F F F F F F F F F
2F
F
F
F
F
F
F F F F F F F F F F F F F F F F F F F F F F
F F F F F F F F F F F F F F F F F F F F F F
ASSISTANCE À LA CLIENTÈLE CANADA SEULEMENT
Pour nous aider à répondre aux questions lorsque vous appelez pour obtenir du
service ou signaler une perte ou un vol, utilisez l’espace ci-dessous pour consigner
le modèle et le numéro de série situés derrière l’appareil.
Numéro de modèle :
Numéro de série :
Date d’achat :
Nom du détaillant :
Adresse :
Ville :
Province :
Code postal :
Téléphone :
SOUTIEN TECHNIQUE
Si vous avez des questions au sujet de la conguration ou du fonctionnement de
votre produit, veuillez consulter la section pertinente dans ce manuel.
Vous pouvez également visiter le www.sharp.ca pour accéder à du contenu exclusif
sur votre produit, notamment pour :
ÆTrouver un détaillant
ÆTrouver des points de service
ÆTélécharger notamment le Guide d’installation, la Fiche technique et le Manuel
de l’utilisateur
CONTACTEZ-NOUS
Si, à tout moment, vous avez des questions ou commentaires concernant votre
produit SHARP, veuillez contacter le Centre d’assistance à la clientèle SHARP.
Nous pouvons vous fournir de l’assistance par divers moyens de communication,
pour mieux vous servir :
https://sharp.ca/contact-sharp CA | www.sharp.ca
Contactez un conseiller Sharp par
téléphone
APPELEZ-NOUS
CA 877-278-6709
De lundi au vendredi :
de 8 h à 17 h est
(sauf les jours fériés)
COURRIEL
Tous les jours, 24
heures sur 24
Consultez la section
Contactez-nous sur
notre site.
SITE DE SOUTIEN
Téléchargements de
produits, Localisateur
de service, Où acheter,
Programme de recyclage
de toner et plus encore.
CANADA CUSTOMER ASSISTANCE
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Sharp SCH3043GB Manuel utilisateur

SCH3043GB
Sharp
Marque
Sharp
Modèle
SCH3043GB
Taper
Manuel utilisateur
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents