Whirlpool PRO 25 IX MIKROBØLGEOVN FOR PROFESJONELT BRUK Manuel utilisateur

Instrukcje użytkowania

Инструкци

Я

за употреба

Návod k použití

Návod na použitie

Instruc∑iuni de utilizare

Инструкции по эксплуатации

ENGLISH

Instructions for use

Page 4

FRANÇAIS

Mode d'emploi

Page 22

ITALIANA

Page

ESPAÑOL

DEUTSCH

Page 78

SVENSKA

Page 97

FINNISH

Page 116

3

4

MODEL:PRO 25 IX

Read these instructions carefully before using your

microwave oven, and keep it carefully.

If you follow the instructions, your oven will provide you with

many years of good service.

SAVE THESE INSTRUCTIONS CAREFULLY

5

PRECA UTIONS TO AVOID POSSIBL E EXPOSURE

TO EXCESSIVE MICROWAVE ENERGY

(a) Do not attempt to operate this oven with the door open since this can

result in harmful exposure to microwave energy. It is important not to

break or tamper with the safety interlocks.

(b) Do not place any object between the oven front face and the door or allow

soil or cleaner residue to accumulate on sealing surfaces.

(c) WARNING: If the door or door seals are damaged, the oven must not

be operated until it has been repaired by a competent person.

ADDENDUM

If the apparatus is not maintained in a good state of cleanliness, its surface could

be degraded and affect the lifespan of the apparatus and lead to a dangerous

situation.

Specifications

Model:

PRO 25 IX

Rated Voltage:

230V~50Hz

Rated Input Power(Microwave):

1550W

Rated Output Power(Microwave):

1000W

Oven Capacity:

25L

Cavity Size:

328x206x368 mm

External

Dimensions:

511 432 311mm

Dimensions With Open Door

511x724x311 mm

Net Weight:

Approx. 14.7 kg

6

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of fire, electric shock, injury to persons

or exposure to excessive microwave oven energy when

using your appliance, follow basic precautions, including

the following:

1.

Warning: Liquids and other foods must

not be heated in sealed containers since

they are liable to explode.

2.

Warning: It is hazardous for anyone other

than a competent person to remove a

cover which gives protection against

exposure to microwave energy.

3.

Warning: Only allow children to use the

oven without supervision when adequate

instructions have been given so that the

child is able to use the oven in a safe way

and understand the hazards of improper

use.

4.

Warning: When the appliance is operated

in the combination mode, children should

only use the oven under adult supervision

due to the temperatures generated.

(only for grill series)

5.

Only use utensils suitable for use in

microwave ovens.

6.

The oven should be cleaned regularly and

any food deposits should be removed.

7.

Read and follow the specific: "PRECAU-

TIONS TO AVOID POSSIBLE EXPOSURE

TO EXCESSIVE MICROWAVE ENERGY".

8.

When heating food in plastic or paper

containers, keep an eye on the oven due

to the possibility of ignition.

9.

If smoke is observed, switch off or unplug

the appliance and keep the door closed

in order to stifle any flames.

10.

Do not overcook food.

11.

Do not use the oven cavity for storage

purposes. Do not store items, such as

bread, cookies, etc. inside the oven.

12.

Remove wire twist-ties and metal handles

from paper or plastic containers/bags

before placing them in the oven.

13.

Install or locate this oven only in

accordance with the installation

instructions provided.

14.

Eggs in the shell and whole hard-boiled

eggs should not be heated in microwave

ovens since they may explode, even

after microwave heating has ended.

15.

Use this appliance only for its intended

uses as described in manual. Do not

use corrosive chemicals or vapors

in this appliance. This oven is especially

designed to heat. It is not designed for

industrial or laboratory use.

16.

If the supply cord is damaged, it must

be replaced by the manufacturer, its

service agent or similarly qualified

persons in order to avoid a hazard.

17.

Do not store or use this appliance

outdoors.

18.

Do not use this oven near water, in a

wet basement or near a swimming

pool.

19.

The temperature of accessible surfaces

may be high when the appliance is

operating. The surfaces are liable to

get hot during use. Keep cord away

from heated surface, and do not cover

any vents on the oven.

20.

Do not let cord hang over edge of table

or counter.

21.

Failure to maintain the oven in a clean

condition could lead to deterioration

of the surface that could adversely

affect the life of the appliance and

possibly result in a hazardous situation.

22.

The contents of feeding bottles and

baby food jars shall be stirred or shaken

and the temperature checked before

consumption, in order to avoid burns.

23.

Microwave heating of beverages can

result in delayed eruptive boiling,

therefore take care when handling the

container.

24.

The appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities,

or lack of experience and knowledge,

unless they have been given supervision

or instruction concerning use of the

appliance by a person responsible for their

safety.

25.

Children should be supervised to ensure

that they do not play with the appliance.

WARNING

7

26.

The microwave oven shall not be placed in a cabinet unless it has been tested in

a cabinet.

27.

Appliances are not intended to be operated by means of an external timer or separate

remote-control system.

To Reduce the Risk of Injury to Persons

Grounding Installation

DANGER

Electric Shock Hazard

Touching some of the internal

components can cause serious

personal injury or death. Do not

disassemble this appliance.

WARNING

Electric Shock Hazard

Improper use of the grounding

can result in electric shock. Do

not plug into an outlet until

appliance is properly installed

and grounded.

CLEANING

Be sure to unplug the

appliance from the power supply.

1. Clean the inside of the oven after using

with a slightly damp cloth.

2. Clean the accessories in the usual way

in soapy water.

3. The door frame and seal and

neighbouring parts must be cleaned

carefully with a damp cloth when they

are dirty.

This appliance must be grounded. In the event of

an electrical short circuit, grounding reduces the

risk of electric shock by providing an escape wire

for the electric current. This appliance is equipped

with a cord having a grounding wire with a

grounding plug. The plug must be plugged into an

outlet that is properly installed and grounded.

Consult a qualified electrician or serviceman if the

grounding instructions are not completely

understood or if doubt exists as to whether the

appliance is properly grounded. If it is necessary

to use an extension cord use only a 3-wire

extension cord.

1. A short power-supply cord is provided to

reduce the risks resulting from becoming

entangled in or tripping over a longer cord.

2. If a long cord set or extension cord is used:

1)The marked electrical rating of the cord set

or extension cord should be at least as great

as the electrical rating of the appliance.

2) The extension cord must be a grounding-

type 3-wire cord.

3) The long cord should be arranged so that it

will not drape over the counter top or tabletop

where it can be pulled on by children or tripped

over unintentionally.

8

UTENSILS See the instructions on "Materials you can use in

microwave oven or to be avoided in microwave oven."

There may be certain non-metallic utensils that are not

CAUTION

Personal Injury Hazard

It is hazardous for anyone

other than a competent person

to carry out any service or repair

operation that involves the removal

of a cover which gives protection

against exposure to microwave

energy.

safe to use for microwaving. If in doubt, you can test the

utensil in question following the procedure below.

Utensil Test:

1. Fill a microwave-safe container with 1 cup of cold

water (250ml) along with the utensil in question.

2. Cook on maximum power for 1 minute.

3. Carefully feel the utensil. If the empty utensil is

warm, do not use it for microwave cooking.

4. Do not exceed 1 minute cooking time.

Materials you can use in microwave oven

Utensils Remarks

Browning dish

Dinnerware

Glass jars

Glassware

Oven cooking

bags

Paper plates

and cups

Paper towels

Parchment

paper

Plastic

Plastic wrap

Follow manufacturer’s instructions. The bottom of browning dish must be

placed smoothly on the ceramic board. Incorrect usage may cause

the ceramic board to break.

Microwave-safe only. Follow manufacturer's instructions. Do not use

cracked or chipped dishes.

Always remove lid. Use only to heat food until just warm. Most glass jars

are not heat resistant and may break.

Heat-resistant oven glassware only. Make sure there is no metallic trim.

Do not use cracked or chipped dishes.

Follow manufacturer’s instructions. Do not close with metal tie. Make

slits to allow steam to escape.

Use for short–term cooking/warming only. Do not leave oven unattended

while cooking.

Use to cover food for reheating and absorbing fat. Use with supervision

for a short-term cooking only.

Use as a cover to prevent splattering or a wrap for steaming.

Microwave-safe only. Follow the manufacturer’s instructions. Should be

labeled "Microwave Safe". Some plastic containers soften, as the food

inside gets hot. "Boiling bags" and tightly closed plastic bags should be

slit, pierced or vented as directed by package.

Microwave-safe only. Use to cover food during cooking to retain

moisture. Do not allow plastic wrap to touch food.

Thermometers Microwave-safe only (meat and candy thermometers).

Wax paper Use as a cover to prevent splattering and retain moisture.

9

Materials to be avoided in microwave oven

Utensils Remarks

Aluminum tray

Food carton with

metal handle

Metal or metal-

trimmed utensils

Metal twist ties

Paper bags

Plastic foam

Wood

May cause arcing. Transfer food into microwave-safe dish.

Metal shields the food from microwave energy. Metal trim may

cause arcing.

May cause arcing and could cause a fire in the oven.

May cause a fire in the oven.

Plastic foam may melt or contaminate the liquid inside when exposed

to high temperature.

Wood will dry out when used in the microwave oven and may split

or crack.

SETTING UP YOUR OVEN

Names of Oven Parts and Accessories

Remove the oven and all materials from the carton and oven cavity.

Your oven comes with the following accessories:

Instruction Manual 1 A

C

B

E

D A) Control panel

B) Observation window

C) Door assembly

D) Safety interlock system

E) Ceramic board

Note: 1) Don't press the ceramic board forcibly.

2) Take and put the utensils gently during the operation in order to avoid damage to the

ceramic board.

3) After using, don't touch the ceramic board by hand in order to avoid high temperature

scald.

10

30 cm

7,5 cm

Open

7,5 cm

Countertop Installation

Remove all packing material and accessories.

Examine the oven for any damage such as

dents or broken door. Do not install if oven is

damaged.

Cabinet: Remove any protective film found

on the microwave oven cabinet surface.

Do not remove the light brown Mica cover

that is attached to the oven cavity to

protect the magnetron.

Installation

1. Select a level surface that provide

enough open space for the intake

and/or outlet vents.

A minimum clearance of 3.0 inches

(7.5cm) is required between the oven and

any adjacent walls. One side must be open.

(1) Leave a minimum clearance of 12

inches (30cm) above the oven.

(2) Do not remove the legs from the

bottom of the oven.

(3) Blocking the intake and/or outlet openings

can damage the oven.

(4) Place the oven as far away from

radios and TV as possible.

Operation of microwave oven may

cause interference to your radio or TV

reception.

2. Plug your oven into a standard household

outlet. Be sure the voltage and the

frequency is the same as the voltage

and the frequency on the rating label.

WARNING: Do not install oven over a

range cooktop or other heat-producing

appliance. If installed near or over a heat

source, the oven could be damaged and

the warranty would be void.

11

Cleaning Instructions

Always keep the oven clean

1. Cleaning the glass viewing window, the inner door panel and oven front face.

For best performance and to maintain the high degree of safety, the inner door panel and

oven front face should be free of food or grease build-up. Wipe these parts with a mild

detergent, rinse and wipe dry. Never use abrasive powders or pads.

2. Cleaning the control panel and plastic parts.

Do not apply a detergent or an alkaline liquid spray to the control panel and plastic parts,

as this may cause damage to these parts.

Use a dry cloth (not a soaked cloth) to clean these parts.

3. Cleaning the oven interior

After use be sure to clean up spilled liquids, spattered oil and food debris as quickly as

possible. If the oven is used when dirty, efficiency drops and the dirt gets stuck on the oven

surface and may cause bad odours. Clean the interior with a cloth soaked in luke-warm

water with a mild detergent dissolved in it, then rinse the soap off with a damp cloth.

CAUTION: Do Not wipe plastic and painted sections of the oven with bleach, thinners or

other cleaning agents, as this may cause these parts to dissolve or change sharp.

12

OPERATION

Control Panel and Features

(

(1)

Power Buttons

(2)

Time entry Button

(3)

X2 Button

(4)

Stop/Reset Button

(5)

Start Button

(6)

Number Buttons

(1)

(2)

(6)

(3)

4)

(5)

13

OPERATION INSTRUCTION

Five power levels are available.

Level

High

M. High

Med.

Defrost

Hold

Power

100%

70%

50%

20%

0%

Display

PL10

PL7

PL5

PL2

PL0

Appendix. A User Options

Items bolded below are the default values.

Option

Setting

Discription

1

EOC Tone

OP:10

3 seconds beep

OP:11

Continuous beep

OP:12

5 quick beeps,Repeating

2

Beeper

Volume

OP:20

Beeper Off

OP:21

Low

OP:22

Medium

OP:23

High

3

Beeper

On/Off

OP:30

Keybeep Off

OP:31

Keybeep On

4

Keyboard

Window

OP:40

15 seconds

OP:41

30 seconds

OP:42

60 seconds

OP:43

120 seconds

5

On the Fly

OP:50

On-the-Fly Disable

OP:51

On-the-Fly Enable

6 Door Reset

OP:60

Door reset Disable

OP:61

Door Reset Enable

7 Max time

OP:70

60 Minute Maximum Cook Time

OP:71

10 Minute Maximum Cook Time

8 Manual

Programming

OP:80

Manual Programming Disable

OP:81

Manual Programming Enable

9

Double Digit

OP:90

Single Digit Mode-10 programs

OP:91

Doule Digit Mode-100 programs

14

Appendix. B Default Cook Times

The oven shall ship with the following Preset Cook Times unless otherwise noted in the

product Specification.

Button

Display (Time)

Power

Cook Factors

1

0:10

100%

80%

2

0:20

100%

80%

3

0:30

100%

80%

4

0:45

100%

80%

5

1:00

100%

80%

6

1:30

100%

80%

7

2:00

100%

80%

8

3:00

100%

80%

9

4:00

100%

80%

0

5:00

100%

80%

15

1. Power Up

" _ _ _ _ " displays when the oven is electrified for the first time. If " " button

pressed, the oven will change to idle mode.

Note: Under idle mode, no button can be pressed.

2. Idle Mode

1) Entry.The oven shall enter idle mode after a set of seconds have expired in Ready Mode

without a keyboard press or a door open and close. The number of seconds is determined

by the keyboard Timeout Window, set by User Option 4.

2) During idle mode, LED is blank.And there shall be no oven activity.

3) Opening and then closing the oven door, the oven will exit the idle mode and into

ready mode.

3. Ready Mode

1) In this mode, the oven is ready to either begin a manual or preset cook cycle.

2) Opening and closing the door while the oven is in Idle Mode will put the oven

into Ready Mode.

2) During Ready Mode, "0:00" displays.

3) From the Ready Mode, the oven can go to almost all of the other modes.

4. Door Open Mode

1) While the door of the oven is open, the oven shall be in Door Open Mode.

This shall also allow for entry into Programming Mode. Whenever the door is open,

the oven shal enter this mode.

2) During this mode, LED is blank. And the fan and oven lamp work.

3) When the door is closed, if User Option OP:60 is selected and the oven was

running a manual or preset cook cycle, the oven shall enter Pause Mode.

In all other cases, the oven shall return to Ready Mode with User Option OP:61

set,opening and closing the door will clear out any information about a Manual or

Preset Program which was running.

16

5. Pause Mode

1) This mode allow the users to temporarily stop the cooking cycle to inspect or

stir the food item.

2) While in Manual Cook Mode, or Preset Program Cook Mode, if the door is open

or closed, or if the " " pad is pressed, the oven will enter Pause Mode.

3) While paused, LED will display the remaining cooking time.

4) Pause Mode will expire back to Idle Mode in the exact fashion as Ready Mode,

dependent on User Option 4. Additionally,if the " " button is pressed, the

oven shall immediately enter Ready Mode.OR if press " " button,

the oven will go into working mode.

6. Manual Cook Entry Mode

1) The user may manuallly enter a cook time and power level while in this mode.

2) While the oven is in the Ready Mode,pressing the pad on the keyboard will

put the oven into Manual Cook Entry Mode.

3) During this mode, "00:00" displays

4) If you press " "," "," " or " " button to select power level,

LED will display the related power. If the same button pressed twice, the power

will change to PL10. If no power chosen, "PL0" is default.

5) During setting process, press " " to enter Manual Cook Mode.

Press " " to enter Ready Mode.

7. Manual Cook Mode

1) This mode allows cooking of the food items.While in Manual Cook Entry Mode, pressing

the " " pad will cause to the oven to begin Manual Cook Mode.

2) During this mode, remaning cooking time displays. The fan and oven lamp will light.

3) When cooking program finish, the oven will enter End of Cook Cycle Mode.

If you press " " button under this mode,the oven will enter Pause Mode.

17

"

8. End of Cook Cycle Mode

1) After the time has expired in a Manual Cook Mode, or a Preset Program Cook

Mode, the oven shall go into The End of Cook Cycle Mode.

2) During this mode, "End" displays.

3) If either User Option OP:11 or "OP:12" is selected, the oven shall continue to sound until

the user acknowledges this by either opening and closing the door or pressing the " "

pad. If User Option OP:12 is selected, after the 3 seconds beep, the oven shall go into

Ready Mode.

9. Preset Program Cook Mode

1) This mode allows cooking of food items through a one pad touch operation.

While in Ready Mode,pressing one of ten digit keys on the keyboard will cause

the oven to run the Preset Program associated with that key.

2) LED displays the remaining cooking time. If it is multi-stage cooking, the total remaning

cooking time displays not a particular stage cooking time.

3) If the program chosen exceeds the maximum time allowed by User Option 7, then the

oven shall beep three times rapidly and display 00:00 to indicate that the program

is unacceptable.

4) When cooking program finish, the oven will enter End of Cook Cycle Mode.

If you press " button under this mode,the oven will enter Pause Mode.

10. On the Fly Cooking

1) The use may start another cook cycle while the oven is cooking or paused.

2) While the oven is cooking or under Pause Mode, if User Option OP:51 is selected

press number buttons, the preset cooking program will start automatically.

3) LED displays the remaining cooking time.

4) When cooking program finish, the oven will enter End of Cook Cycle Mode.

If you press " button under this mode,the oven will enter Pause Mode.

18

11. Programming Mode

This mode allows the user to assign cook times and power levels to the once touche button.

1) Open the door and press "1" for 5 seconds,the buzzer will sound once and enter to

Programming Mode.

2) "ProG" displays.

3) Press " " button, LED will display the saved time, then you can input the time

you need.

4) Press " "," "," " or " " to input the power level.

LED will display the related power. If the same button pressed twice, the power

will change to PL10. If no power chosen, "PL0" is default.

5) To change the cooking fators: If press "X2",LED will display "CF:XX". The default factor is

80%. "CF:80" displays. If you need to change the cooking power, just press one of

the number buttons to set.

6)After setting the time and power, press " ", the cooking program will be saved.

When the program saved, "ProG" displays.

7) If all the cooking time exceeds the MAX.time User Option 7, when press

" " to save the program, the buzzer will sound three times briefly and LED will diaply

"00:00" to tell you the time is no use. And then LED turn back to show "ProG". The time

set before will be no change.

8) Close the door, the oven will turn back to Ready Mode.

If press " " button during setting process, the oven turn to Door Open Mode.

The program that not saved will be lost. If there is program saved as memory procedure,

press the related number button, the saved program will start. If no saved program,

the buzzer will alarm when pressing number button and it will not work.

For example: set the program as memory cooking.

Program; Power level PL7 and cooking time is 1 minute and 25 seconds.

Step1: In waiting state, press number button "1" for 5 seconds,"ProG" displays.

Step 2: Press number button "3", the program will be saved in "3".

Step 3: Press " ", "0:00" displays.

Step 4: Press number buttons "1", "2" and "5" to input the cooking time.

Step 5: Press " " button," PL7" displays. Setting finished.

Step 6: Press " " to save. When use the program next time, just press "3",

Note: the related program will start.

1. If the electricity is cut off, the saved program will not lost.

2. If the program need to reset , just repeat the aboved steps.

3. If press " " at the last step, it will turn back to Ready Mode. The setting will be no use.

19

12. Double Quantity cooking

1) Through the use of the X2 pad, the user can easily set the time two of a particalar

food item.

2) Under waiting state, press "X2" button and then press number buttons 0-9 in 5 seconds,

the oven will start cooking with the quantity preset cooking time.

3) Press "X2", "doub" displays. When press number buttons, LED will display the quantity

preset time.

For example, number button "5" and its preset time is 1 minute. Then press "X2", then time

will change to 1:00*(1+0.8)=1:48

4) When cooking program finish, the oven will enter End of Cook Cycle Mode.

Note: This function cannot be used under memory mode.

13. Stage Cooking Programming

This allows the user to cook food items at combination of various Power Levels.

1) Three stages can be set at most under cooking mode or memory mode.

Aftet setting the power and time for the first stage, press " " to set the second stage.

And the same step to set the third stage.

2) When setting the second or the third stage, press " ", "S-2" or "S-3" displays.

3) Press " " button to start cooking.

Example: To set three stages as memory mode. The first stageis PL7 and time is 1 minute

25 seconds. The second stage is PL5 and 5 minutes and 40 seconds. The steps are follow.

a. Waiting state, press "1" for 5 seconds, LED displays "ProG".

b. Press number buttons "3" to save the program in "3".

c. Press " ","00:00" displays.

d. Press "1","2","5" to input the cooking time. "1:25" displays.

e. Press " ", "PL7" displays.

The first stage is finished.

f. Press " ", LED displays "2".

g. Press "5", "4","0" button, "5:40" displays.

h. Press " ", "PL5" displays.

The second stage is finished.

La page est en cours de chargement...

Whirlpool PRO 25 IX MIKROBØLGEOVN FOR PROFESJONELT BRUK Manuel utilisateur

Whirlpool PRO 25 IX MIKROBØLGEOVN FOR PROFESJONELT BRUK Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents