Bercomac 700527-2 700528-1 Manuel utilisateur

Taper
Manuel utilisateur

Ce manuel convient également à

1
BERCO
Subframe with Electric Lift & Drive Mechanism
for
CUB CADET LTX, SLTX & GTX
TORO 2010 LX & GT & 2010 MTD 900 SERIES
CAUTION:
READ & FOLLOW ALL SAFETY RULES & INSTRUCTIONS BEFORE
OPERATING YOUR EQUIPMENT
M-10
* ASSEMBLY * REPAIR PARTS
* OPERATION * MAINTENANCE
*106218*
OWNER’S MANUAL
Model Number
700527-2 Subframe with Winch
700528-1 Compact Drive Mechanism
700529-1 Northeast Drive Mechanism
106218_EN
2
LIMITED WARRANTY
Bercomac Limitée
92, Fortin North, Adstock, Quebec, Canada, G0N 1S0
Conditions and Products Covered:
BERCOMAC guarantees any part of the product or accessory
manufactured by BERCOMAC and found in the reasonable
judgment of BERCOMAC to be defective in material and or
workmanship will be repaired or replaced by an authorized
dealer without charge up to our maximum labor rates and pre-
established times. For replacement parts only standard ground
freight services are covered. This warranty extends to the
original retail purchaser only and is not transferable to any
subsequent purchasers. This warranty applies to the products
bought and used in North America.
Warranty Period
(from date of the original retail purchase)
Residential use: 1 year
Semi-commercial, professional or rental use: 90 days
Exceptions Noted Below; the following items are guaranteed
by the original manufacturer and have their own warranty,
conditions and limited time:
Tire Chains: 90 days
Engines: Will vary as per the manufacturer
Please refer to the engine manufacturer’s warranty
statement included with the unit. BERCOMAC is not
authorized to handle warranty adjustments on engines.
Items and Conditions NOT Covered:
This warranty does not cover the following:
Pick-up or delivery charges or in-home services fees.
Any damage or deterioration of the unit, parts and or finish
of these due to normal use, wear and tear, or exposure.
Cost of regular use or maintenance service or parts, such as
gas, oil, lubricants, tune-up parts, and adjustments.
Any part or accessory which has been altered, modified,
misused, neglected, accidentally damaged or not properly
installed, maintained, stored or repaired not in accordance
with the instructions in the owner’s manual.
Repair due to normal wear and or any wear items such as
shear pins, bolts, belts, etc.
Expedited freight fee services for replacement parts.
Shear bolts and shear pins are to be considered as a
preventive measure not as an assured protection, any
damages resulting from the lack of shear bolts breakage are
not covered.
Damages due to product being installed on a vehicle other
than stipulated in owner’s manual.
NOTE: All warranty work must be performed by an authorized
dealer using original (manufacturer) replacement parts.
Owner’s Responsibilities:
BERCOMAC’s defective equipment or part must be returned
to an authorized dealer within the warranty period for repairs.
In the event that defective merchandise must be returned to
manufacturer for repairs, freight fees are prepaid and a written
authorization from BERCOMAC must be obtained by dealer
prior to the shipment. This warranty extends only to
equipment operated under normal conditions. To validate a
warranty claim, it is the user’s responsibility to maintain and
service the unit as specified in the owner’s manual or to have
the unit serviced at their dealer at their expense.
General Conditions:
The sole liability of BERCOMAC with respect to this warranty
shall be strictly and exclusively repair and replacement as
mentioned herein. BERCOMAC shall not have any liability for
any other costs, loss or damage, including but not limited to,
any incidental or consequential loss or damage.
Taking advantage of the warranty does not in any way extend
the length or renewal of the warranty.
In particular, without being limited to, BERCOMAC shall have
no liability or responsibility for:
Travel time, overtime, after hours time or other
extraordinary repair charges or relating to repairs and or
replacements outside of normal business hours.
Rental of like or similar replacement equipment during the
period of any, repair or replacement work.
Any communicating or travel charges.
Loss or damage to person or property other than that
covered by the terms of this warranty.
Any claims for lost revenue, lost profit or any similar costs
as a result of damage or repair.
Attorney’s fees.
BERCOMAC’s responsibility in respect to claims is limited to
making the required repairs or replacement without charge up
to our maximum labor rates and pre-established times and no
claim of breach of warranty shall be cause for cancellation or
rescission of the contract of sale of any product or accessory.
In no event recovery of any kind be greater than the amount of
the purchase price of the product sold.
This warranty gives you specific legal rights. You may also
have other rights, which vary from state to state.
NOTE: Bercomac reserves the right to change or improve the design of any part or accessory without assuming any obligation to modify
any product previously manufactured.
Instructions for Obtaining Warranty Services:
Contact dealer where equipment was purchased or any other BERCO service dealer to arrange service at their dealership. Requests for
warranty claims must be carried out through the same distribution network used to purchase the product.. Don't forget to bring your proof
of purchase (sales receipt) to the BERCOMAC dealer.
1
TABLE OF CONTENTS
INTRODUCTION ...................................................................................................................................................... 2
SAFETY PRECAUTIONS ........................................................................................................................................ 3
SAFETY DECALS .................................................................................................................................................... 5
ASSEMBLY
Tools Required ........................................................................................................................................... 6
Step 1: Subframe Installation ..................................................................................................................... 6
Step 2: Installation the Winch Control Switch ........................................................................................... 10
Step 3: Drive Mechanism Installation ........................................................................................................ 13
OPERATION & MAINTENANCE
Controls ....................................................................................................................................................... 16
Maintenance ............................................................................................................................................... 16
Belt Replacement ....................................................................................................................................... 16
Verify Tire Pressure .................................................................................................................................... 16
DISMOUNTING & STORAGE
Dismounting ................................................................................................................................................ 16
Storage ........................................................................................................................................................ 16
TROUBLE SHOOTING ............................................................................................................................................ 17
PARTS BREAKDOWN AND PARTS LIST
Compact Drive Mechanism 700528-1 ...................................................................................................... 19
Northeast Drive Mechanism 700529-1 ..................................................................................................... 21
Subframe 700527-2 ................................................................................................................................... 23
Winch 106125 ............................................................................................................................................... 26
TORQUE SPECIFICATION TABLE ....................................................................................................................... 27
ATTACHMENTS ....................................................................................................................................................... 28
PAGE
2
INTRODUCTION
SERIAL NUMBER : ___________________________
(IF APPLICABLE)
MODEL NUMBER: ___________________________
PURCHASE DATE : ___________________________
3
SAFETY PRECAUTIONS
Careful operation is your best insurance against an accident. Read this section carefully before operating the vehicle
and accessory. This accessory is capable of amputating hands and feet and throwing objects. Failure to observe the
following safety instructions could result in serious injury. All operators, no matter how experienced they may be,
should read this and other manuals related to the vehicle and accessory before operating. It is the owner's legal
obligation to instruct all operators in safe operation of the accessory.
GLOSSARY:
In this manual, right and left sides are determined by
sitting on the seat of the vehicle facing forward.
In this manual, "accessories" means attachments
(snowblower, rotary broom, blade etc.) that you install
on the vehicle (lawn tractors, A.T.V. s etc).
TRAINING:
This symbol, "Safety Alert Symbol", is used
throughout this manual and on the
accessory’s safety labels to warn of the
possibility of serious injury. Please take
special care in reading and understanding
the safety precautions before operating the
vehicle and accessory.
1. Read this owner's manual carefully. Be thoroughly
familiar with the controls and proper use of the
vehicle and accessory. Know how to stop the unit
and disengage the controls quickly.
2. Never allow children to operate the vehicle nor the
accessory. Never allow adults to operate the vehicle
nor the accessory without proper instructions.
3. No one should operate the vehicle nor the
accessory while intoxicated or while taking
medication that impairs the senses or reactions.
4. Keep the area of operation clear of all people,
particularly small children and pets.
PREPARATION:
1. Thoroughly inspect the area where the accessory
is to be used and remove door mats, all foreign
objects and the like.
2. For motorized accessories, disengage all clutches
and shift into neutral before starting engine.
3. Do not operate the accessory without wearing
adequate winter outer garments. Avoid loose fitting
clothing that can get caught in moving parts. Wear
footwear that will improve footing on slippery
surfaces.
4. Handle fuel with care, it is highly flammable.
a) Use approved fuel container.
b) Never add fuel to a running engine or hot engine.
c) Fill fuel tank outdoors with extreme care. Never fill
fuel tank indoors.
d) Never fill containers inside a vehicle, or on a
truck or a trailer bed with a plastic liner. Always
place containers on the ground, away from your
vehicle, before filling.
e) When practical, remove gas-powered
equipment from the truck or trailer and refuel it
on the ground. If this is not possible, then refuel
such equipment on a trailer with a portable
container, rather than from a gasoline
dispenser nozzle.
f) Keep the nozzle in contact with the rim of the
fuel tank or container opening at all times, until
refueling is complete. Do not use a nozzle lock-
open device.
g) Replace fuel cap securely and wipe up spilled
fuel.
h) If fuel is spilled on clothing, change clothing
immediately.
5. Never attempt to make any adjustments while the
engine (motor) is running (except when specifically
recommended by manufacturer).
6. Let the vehicle and accessory adjust to outdoor
temperatures before using.
7. Never use an accessory without proper guards,
plates, or other safety protective devices in place
8. Always make sure to wear the appropriate safety
equipment required (glasses, muffs, mask…) for
each type of product. See operation section.
9. Always make sure of having safe traction on the
vehicle by using the recommended accessories
(chains, A.T.V. tracks, counterweights…). See
operation section.
10. Always make sure the all components are correctly
installed. (driveline securely attached and locked at
both ends, belts properly installed…)
11. Always handle the winch cable with thick leather
gloves.
12. Never modify the accessory or any part without
the written consent from the manufacturer.
4
OPERATION:
1. Do not put hands or feet near, under or inside rotating
parts.
2. Exercise extreme caution when operating on or
crossing gravel drives, walks or roads. Stay alert for
hidden hazards or traffic. Do not carry passengers.
3. After striking a foreign object, stop the engine (motor),
disconnect the wire from the spark plug(s) and keep
wire away to prevent accidental starting. Thoroughly
inspect the accessory for any damage and repair
damage before restarting and using the accessory.
4. If the unit should start to vibrate abnormally, stop the
engine (motor) and check immediately for the
cause. Vibration is generally a warning of trouble.
5. Take all possible precautions when leaving the
vehicle unattended. Disengage the power take-off,
lower the attachment, place the transmission into
neutral, set the parking brake, stop the engine and
remove the contact key.
6. Do not run the engine indoors, except when starting
the engine and for transporting in or out of the
building. Do not operate or let motor run in a storage
area without ventilation because gas contains
carbon monoxide which is odorless, colorless and
can cause death.
7. Never use the accessories across the face of
slopes, go from top to bottom. Exercise extreme
caution when using equipment on slopes. Do not
attempt to clear a steep slope.
8. Never tolerate bystanders in the working zone.
Never use an accessory in the direction of
bystanders, it might throw gravel or debris that can
hurt people or damage property.
9. Never operate the accessory at high transport
speeds on slippery surfaces. Use care when
backing up.
10. Do not carry passengers.
11. Disengage power to the accessory when it is
transported or not in use.
12. Never operate the accessory without good visibility
or light.
13. Keep the accessory away from heat sources or
flames.
14. Never handle the winch cable or hook while in
tension.
MAINTENANCE AND STORAGE
1. When cleaning, repairing or inspecting the vehicle
and accessory, make certain that all moving parts
have stopped. For gasoline engine, disconnect wire
from the spark plug(s) and keep wire away to
prevent accidental starting.
2. Check all the bolts and components at frequent
intervals to make sure that they are properly
tightened.
3. Never store a motorized accessory with fuel in the
fuel tank inside a building where ignition sources are
present such as hot water and space heaters,
clothes dryers, and the like. Allow the engine to cool
before storing in any enclosure.
4. Always refer to the owner’s manual when you store
the accessory and vehicle for a prolonged or an
unspecified length of time.
5. Maintain or replace safety and instruction labels, as
necessary.
6 For winter accessories, (if applicable), let the engine
run for a few minutes after clean snow in order to
prevent the rotary parts from freezing.
7. Inspect the vehicle’s and accessory’s air filter (if
applicable) every day. Clean it or replace it as
necessary. Change the oil more often when working
in dusty conditions. See the vehicle’s and
accessory's owner’s manual.
THIS SYMBOL MEANS
DANGER !
BECOME ALERT !
YOUR SAFETY IS INVOLVED !
SAFETY PRECAUTIONS
5
SAFETY DECALS
REPLACE IF DECALS ARE DAMAGED
SEE PARTS BREAKDOWN FOR DECAL LOCATION
DECAL #105133
Failure to observe these instructions could lead to
severe injury or death.
To avoid injury to hands or fingers:
-Always keep hands clear of rope hook loop, ,hook and
fairlead opening during installation , operation and
when spooling in or out.
-Always use extreme caution when handling hook and
rope during spooling operations.
-Always wear heavy leather gloves when handling rope.
-Keep hands away from the hot surface.
6
ASSEMBLY
Install the left & right supports (item 2) on each side of
the vehicle.
Item # Description Action
1 Tractor shoulder screw Remove from both
sides of tractor.
2 Left & right support
(qty 2) Install on each side
as shown.
3 Lock washer
(qty 2) Insert on the bolt
(item 5) as shown.
4 Flat washer
(qty 2) Insert on the bolt
(item 5) as shown.
5 Hex bolt 1/2’’ x 1’’
(qty 2 ) Insert as shown.
6 Hex nut 1/2’’ thin,
(qty 2) Do not tighten.
NOTE: Save the tractor shoulder bolts in case you
reinstall the bumper.
IMPORTANT: TORQUE ALL BOLTS ACCORDING TO TORQUE SPECIFICATION TABLE WHEN STATED:
TIGHTEN FIRMLY.
THE WINCH KIT IS TO BE USED ONLY TO LIFT BERCO ACCESSORIES, ANY OTHER USE MAY CAUSE
DAMAGE TO THE VEHICLE.
This subframe may be used to install different attachments (see attachments page). Once installed, it may
remain permanently on your vehicle.
NOTE: It is not necessary to remove mower deck at this step.
STEP 1
SUBFRAME INSTALLATION:
Refer to parts breakdown section for parts
identification.
TOOLS REQUIRED:
Wrenches:1/2, 3/4, 5/16, 7/16, 9/16, 10mm
Ratchet
Sockets: 2/16, 1/2, 9/16, 3/4, 10mm
Cutting pliers
Pliers
Square head screwdriver: #2, #3
Please sort out and identify all the hardware before
starting installation. Lists for the hardware bag and for
the box are supplied in each.
Install the supports
Install the left & right supports (items 1 & 2) on each
side of the vehicle.
Item # Description Action
1 & 2 Left & right support Install as shown.
3 Hex bolt
5/16’’ x 1‘’ Insert in supports as
shown.
4 Hex bolt 5/16’’ x 1/2‘’
(qty 3) Insert in supports as
shown.
5 Hex nut 5/16’’
(qty 4) Install on bolts and
tighten firmly. Install the supports
INSTALLING THE REFLECTORS
IMPORTANT: When operating the tractor with the
front mounted attachment, install the two red-colored
adhesive reflectors on the rear vertical surface of the
tractor’s fender.
7
ASSEMBLY
NOTE: Remove tractor bolt (A) from under the foot rest
pad as shown.
Remove tractor bolt (B) from underneath the foot rest.
Keep the bolts in a safe place for future installation.
Install handle support (item 4).
Item # Description Action
1 Carriage bolt
5/16’’n.c. x 1 1/2’’ Insert as shown.
2 Flat washer Install as shown on
bolt.
3 Sleeve Insert on the bolt as
shown. *
4 Handle support Insert on the bolt as
shown
5 Flange nut
5/16’’ n.c. Do not tighten.
6 Carriage bolt
5/16’’ n.c. x 3/4’’ Insert as shown.
7 Flange nut
5/16’’ n.c Tighten firmly.
8 Plastic grommet Insert as shown.
9 Square head set
screw
5/16’’ n.c. x 1/2’’
Insert as shown.
NOTE: Tighten firmly all the nuts. Put the pad of the
foot rest in place.
* Do not use if there is a rubber bushing. Install handle support
Install the left & right braces (items 1 & 2) on each
side of the vehicle.
Item # Description Action
1 & 2 Left & right brace
(qty 2) Install on the inside
as shown.
3 Hex bolt
3/8’’ n.c. x 1‘’
(qty 4)
Insert the bolts as
shown (one inside
the other outside).
4 Nylon insert lock nut
3/8’’
(qty 4)
Insert on the bolts as
shown.
Tighten firmly.
NOTE: Tighten firmly the hex. bolts (item 5) on both
sides. Install the braces
For the 42’’ mower deck only: Remove the mower
deck stopper and keep in safe place.
8
NOTE 2: If your tractor has the muffler coming out the
front as shown in the drawing, please install the heat
shield as shown below.
If the muffler come out in another position, you do not
need the heat shield.
ASSEMBLY
Install the female hitch (item 1)
# Item Description Action
1 Female hitch Install between the
two supports.
2 Heat shield Install the heat
shield inside the
female hitch.*
3 Hex bolt 3/8 x 1’’
(qty 4) Insert as shown.
4 Flange nut 3/8’’
(qty 4) Tighten all the nuts
firmly.
* See NOTE 2 at top of page
Install the female hitch between the two supports
Install the spring (item 1)
# Item Description Action
1 Spring Install the spring
on the frame as
shown.
NOTE: The latch must move freely.
Install the spring as shown
9
ASSEMBLY
NOTE: Lift the front part of foot rest to remove tractor
bolt (item 1). Install the cab support (item 5).
# Item Description Action
1 Tractor bolt Remove from
tractor.
2 Carriage bolt
5/16’’n.c. x 1 1/2’’ Insert as shown.
3 Flat washer Install as shown on
bolt.
4 Sleeve Insert on the bolt as
shown.*
5 Cab support Insert on the bolt as
shown.
6 Flange nut 5/16’’ n.c. Tighten.
7 Square head set
screw 5/16 x 1/2’’ Insert in the hole of
the cab support.
NOTE: Keep the tractor bolt in a safe place for future
installation.
* Do not use if there is a rubber bushing. Install the cab support
10
ASSEMBLY
Install the winch control switch
STEP 2:
INSTALLATION OF THE WINCH CONTROL
SWITCH
Install the relay (item 1).
#
Item Description Action
1 Relay Install in an appropriate
area.
2 Metal screw
#12 x 3/4’’ (qty 4) Secure relay in place.
*3 Nylon tie wrap 8’’
(qty 4) See *
*If necessary use the nylon tie wraps to secure the
relay in place.
** Install in a sheltered place away from bad weather.
Install the relay
IMPORTANT
To prolong the winch cable’s life, release the winch control switch as soon as the accessory touches the
ground. This will keep the cable from tangling up which causes premature wear.
Before drilling the hole, check behind the dashboard
to make sure there is enough space to install the
switch.
Drill a 1/2’’ hole in the dashboard or an appropriate
place (see reference drawing). Stick the UP/DOWN
decal over the hole for the switch.
Insert the switch in the hole and secure in place with
the rubber boot.
NOTE: It is important to install the switch vertically.
Connect the wires as shown.
When the switch is raised, the winch must lift the
accessory. If you prefer the contrary, invert the green
and black wires.
Connect the wires
Up / Down decal
11
ASSEMBLY
CONNECTING THE WIRES
NOTE: The posts on the relay are identified by
numbers. (1-2-3-4).
Install the wires from the winch on the posts of the
relay.
Red wire (+) on post #3.
Black wire (-) on post #4.
Connect the red wire from the winch (limit switch) with
the green wire from the relay.
Connect the wires
IDENTIFY THE IGNITION WIRE:
Place the clip of the Hi / Low tester on the negative
post (-) on the battery or a metal surface without any
paint.
Turn the ignition key to the position: Accessory.
Insert the tip of the tester in a hole at the back of the
starter (switch) make sure to touch the metal part of
the wire (on most tractors, it is the A1 terminal on the
ignition switch that is used for accessories. Before
connection, verify with HI/LOW tester).
If the tester’s light turns on, turn the ignition key to the
position, Off. The light must turn off.
You have identified the ignition wire, if not repeat the
operation on another wire.
INSTALL THE CONTROL WIRE:
Join the ignition wire and the red wire from the winch
control (item 1) with the instant connector (item 2).
Connect the black wire of the winch control (item 3) to
the black wire on the relay.
Connect the green wire of the winch control (item 3)
with the red wire of the winch (limit switch).
Connect the ignition wire
12
ASSEMBLY
CAUTION
FOR YOUR SECURITY:
Read and follow the safety precautions for the
battery in the vehicle’s manual.
CONNECT THE WIRES ON THE BATTERY:
Connect the wires from the relay to the vehicle’s
battery.
The red wire (+) on the positive post of the battery
(item 1).
The black wire (-) on the negative post of the battery
(item 2).
Make sure to tighten the nuts on the posts.
TIE ALL THE WIRES:
NOTE: Make sure the wires from the control
assembly do not interfere with anything on the tractor
nor come into contact with any heating, electrical or
removable elements of the tractor.
Tie the wires with four nylon tie wraps included in the
kit.
Connect the relay wires to the battery
Install the heat shield (item 1).
# Item Description Action
1 Heat shield Install as shown.
2 Hex bolts
1/4 x 1/2’’
(qty 2)
Tighten firmly.
Install the heat shield
VERY IMPORTANT:
Make sure the cable winds up and unrolls as shown
in the figure (cable under the spool).
Lubricate the winch cable and the drum periodically
with grease.
If the winch cable does not wind up from the
bottom of spool as shown, the limit switch will not
work and may cause damage to the subframe,
winch and accessory.
13
ASSEMBLY
STEP 3:
DRIVE MECHANISM INSTALLATION:
WARNING
TO PREVENT INJURIES:
It is the person who installs the drive mechanism
responsibility to make sure that when the clutch
is disengaged that all moving parts stop.
For more information, do not hesitate to contact
the technical support.
WARNING
TO PREVENT INJURIES:
Stop the motor.
Apply parking brake.
Remove the ignition key.
Disconnect the wire from the spark plug(s) and
keep away from spark plug(s) to prevent accidental
starting.
NOTE: You must remove mower deck to install
the drive mechanism.
Install the drive mechanism (item 1).
# Item Description Action
1 Back of drive
mechanism Hook on the tractor frame,
right side.
2 Front of drive
mechanism Install between the
supports.
4 Pin
(qty 2) Insert as shown.
On the right side, pin and
sleeve (item 3) from the
outside.
On the left side, and pin
from the inside.
5 Hair pin
(qty 2) Secure the pins.
6 Carriage bolt
5/16’’ x 1’’ Insert in the back of the
drive as shown.
7 Bracket Install on the bolt as
shown and on the tractor
frame.
8 Knob Tighten to lock the drive
frame in place. Install drive mechanism
For tractors with Electric Clutch:
Install the belt on the engine pulley of the vehicle.
Check the tension on the spring.
If necessary, adjust the tension by moving the
adjustment rod (item 1) and tighten the set screw
(item 2).
No modifications to be done
14
ASSEMBLY
For tractors with Manual Clutch activated by a
cable:
Install the tractor’s manual clutch cable .
* Remove the spring.
# Item Description Action
1 Spring from the clutch
cable Install as shown in
the hole on the
tension pulley.
2 Clutch cable Insert in the slot on
the adjustment rod.
3 Hair pin 2mm Secure the cable.
4 Adjustment rod Slide towards the
back to apply enough
tension on the spring.
5 Square head set
screw 5/16 x 1/2’’ Secure the
adjustment rod.
Install the belt on the engine pulley of the vehicle.
Check the tension on the spring.
If necessary, adjust the tension by moving the
adjustment rod and tighten the set screw.
Install the manual clutch cable
Secure clutch cable
Install the cable clip (item 2).
# Item Description Action
1 Hex bolt.
1/4 x 1/2’’ Install as shown
(choose a hole)
2 Cable clip Insert the cable in
the clip and insert
on bolt as shown.
3 Flange nut 1/4’’ Tighten firmly.
15
ASSEMBLY
If applicable, you can remove or add a flat washer
(item 1) on the tension pulley (item 2) for a better
adjustment.
Engage and disengage the clutch a few times and
make sure the belt does not touch the belt guide in
any place when the drive mechanism is engaged.
VERIFICATION OF THE BELT AND PULLEY
ALIGNMENT:
WARNING
TO PREVENT INJURIES:
It is the person who installs the drive mechanism
responsibility to make sure that when the clutch
is disengaged that all moving parts stop.
For more information, do not hesitate to contact
the technical support.
WARNING
TO PREVENT INJURIES:
do this verification when the engine of the vehicle
is not running.
Adjust the pulleys
16
OPERATION & MAINTENANCE
CAUTION
Read the vehicle Owner’s Manual carefully. Be
thoroughly familiar with the controls & proper
use of the attachment. Know how to stop the
attachment quickly.
IMPORTANT:
THE WINCH KIT IS TO BE USED ONLY TO LIFT
BERCO ACCESSORIES, ANY OTHER USE MAY
CAUSE DAMAGE TO THE VEHICLE.
MAINTENANCE
a) Check mounting bolts at frequent intervals for
proper tightness to be sure equipment is in safe
working condition.
b) Apply oil at all pivot points.
c) To prolong the life span of the winch, make sure the
snap mount switch works well.
BELT REPLACEMENT
Belt for the accessories:
SEE ATTACHMENT OWNER'S MANUAL
(SNOWBLOWER AND BROOM) FOR REPLACING
INSTRUCTIONS.
Drive Mechanism Belt:
a) Dismount the drive mechanism.
b) Remove the bolt which retains the tension pulley.
c) Replace the belt and re-install the tension pulley.
Before tightening make sure the belt guide does
not touch the belt at any time.
d) Re-install the drive mechanism.
e) Check the alignment of the belt that joins the
drive mechanism to the engine pulley.
VERIFY TIRE PRESSURE:
Tire pressure must be even on both sides of the
tractor according to the vehicle’s owner’s manual.
DISMOUNTING & STORAGE
DISMOUNTING
SEE ATTACHMENT OWNER'S MANUAL
(SNOWBLOWER, BROOM AND BLADE) FOR
DISMOUNTING INSTRUCTIONS.
a) Dismount the attachment.
b) Remove the rear counterweight when you remove
the front attachment (if applicable).
c) Remove the belt from the engine pulley.
d) Dismount the drive mechanism by supporting it in
your hand. Carefully lower to the ground.
Manual clutch activated by cable:
Unhook cable shield by removing the hair pin.
Unhook spring. Pull out drive mechanism from
underneath tractor.
e) You may leave the subframe on tractor all year long
or remove it if preferred.
f) Reinstall mower if needed.
STORAGE
a) Clean and paint all parts from which paint has worn.
b) Apply oil at all pivot points.
c) Inspect and replace all defective parts before using
again.
CONTROLS
IMPORTANT:
In order to avoid draining the battery of the
vehicle, always start the engine before using the
winch.
THE WINCH CONTROL SWITCH
Push up or down the winch control switch to lift or
lower the accessory to the ground.
There is a limit switch stopper that limits the lifting.
Always prestretch cable and respool under load
before installing the hook on the accessory. A tightly
wound cable reduces chances of binding, which can
cause damage to the cable.
To prolong the winch cable’s life, release the winch
control switch as soon as the accessory touches the
ground. This will keep the cable from tangling up,
causing premature wear of the cable.
WINCH CABLE MAINTENANCE
To reduce the risk of cable failure during the season,
we recommend changing the winch cable every year.
Lubricate the winch cable and the drum periodically
with grease.
Install the new winch cable as shown in figure in the
parts breakdown.
17
TROUBLESHOOTING
* Please refer to parts breakdown section for parts identification.
PROBLEM POSSIBLE CAUSES CORRECTIVE ACTION
Winch runs backwards or stays Winch wires reversed. Recheck wiring.
stuck in up position. Switch wires reversed. Recheck wiring.
Switch installed incorrectly. Check switch installation.
Battery wires reversed. Recheck wiring.
Winch cable is not winded up from
the bottom of spool. Wind winch cable from the bottom
of the spool. (see assembly section
in subframe manual)
Winch will not operate or runs in one
direction only. Vehicle’s ignition switch is at OFF
position. Turn vehicle’s ignition switch at ON
position.
Broken wires or bad connection. Check for poor connections.
Control switch is inoperative. Replace control switch.
Relay or breaker is damaged. Replace the relay or breaker.
Limit switch is damaged or wires
disconnected from limit switch. Replace limit switch or verify wire
connections on limit switch.
Winch is damaged. Replace or repair winch.
Winch runs but with insufficient power
or line speed. Weak battery. Recharge or replace battery.
Check charging system
Poor battery connection. Check battery terminals for
corrosion. Clean when required.
Winch is damaged. Replace or repair winch.
Winch cable breaking prematurely. Frequently stopping the winch when
accessory is going down. Doing complete up and down cycles
and avoid stopping midway.
Cable tangling up. Release the control switch as soon
as the accessory touches the
ground.
Winch drum and cable wearing
prematurely. Insufficient lubrication of winch drum
and cable. Lubricate winch drum and cable
periodically with grease.
Winch does not hold the accessory in
up position. Winch is damaged. Replace or repair winch.
18
TROUBLESHOOTING
HOW TO KNOW POINTS TO CHECK
Poor connections. Recheck wiring with the owner's manual
HI/LOW voltage tester does not work. Connect it on battery posts (+ and -) of a functional battery.
If there is no light, the tester is damaged.
The control switch inoperative. Test both connectors with HI/LOW voltage tester.
If light comes ON or the relay is clicking in both positions (UP &
DOWN), the control switch is operative.
Relay is damaged If there is voltage on battery wire posts 1 & 2 on the relay and no
voltage on posts 3 & 4 when control switch is activated and relay is
clicking in both directions, the relay is defective. (see relay assembly
section in owner’s manual for relay post identification). Check
connections with HI/LOW voltage tester.
Winch is damaged The ultimate test is to connect the winch directly to the battery and
reverse the wires to test both directions. If the winch doesn't work, it is
damaged.
The limit switch is damaged. When the limit switch is pushed or stuck inside, the winch can't raise
the accessory, only lower it. If not working properly replace it.
The breaker is damaged. Place clip of the HI / LOW voltage tester on negative (-) post of the
battery. Check the voltage with the tip of the tester on both terminals
of the breaker. If voltage only on 1 terminal replace the breaker.
(sometimes it could take a few minutes for the breaker to
automatically reset itself)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

Bercomac 700527-2 700528-1 Manuel utilisateur

Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues