Bercomac 700527-2 700528-1 Manuel utilisateur

Marque: Bercomac

Modèle: 700527-2 700528-1

Taper: Manuel utilisateur

Ce manuel convient également à

700527-2 700529-1

BERCO

Subframe with Electric Lift & Drive Mechanism

for

CUB CADET LTX, SLTX & GTX

TORO 2010 LX & GT & 2010 MTD 900 SERIES

CAUTION:

READ & FOLLOW ALL SAFETY RULES & INSTRUCTIONS BEFORE

OPERATING YOUR EQUIPMENT

M-10

* ASSEMBLY * REPAIR PARTS

* OPERATION * MAINTENANCE

*106218*

OWNER’S MANUAL

Model Number

700527-2 Subframe with Winch

700528-1 Compact Drive Mechanism

700529-1 Northeast Drive Mechanism

106218_EN

LIMITED WARRANTY

Bercomac Limitée

92, Fortin North, Adstock, Quebec, Canada, G0N 1S0

Conditions and Products Covered:

BERCOMAC guarantees any part of the product or accessory

manufactured by BERCOMAC and found in the reasonable

judgment of BERCOMAC to be defective in material and or

workmanship will be repaired or replaced by an authorized

dealer without charge up to our maximum labor rates and pre-

established times. For replacement parts only standard ground

freight services are covered. This warranty extends to the

original retail purchaser only and is not transferable to any

subsequent purchasers. This warranty applies to the products

bought and used in North America.

Warranty Period

(from date of the original retail purchase)

Residential use: 1 year

Semi-commercial, professional or rental use: 90 days

Exceptions Noted Below; the following items are guaranteed

by the original manufacturer and have their own warranty,

conditions and limited time:

Tire Chains: 90 days

Engines: Will vary as per the manufacturer

Please refer to the engine manufacturer’s warranty

statement included with the unit. BERCOMAC is not

authorized to handle warranty adjustments on engines.

Items and Conditions NOT Covered:

This warranty does not cover the following:

Pick-up or delivery charges or in-home services fees.

Any damage or deterioration of the unit, parts and or finish

of these due to normal use, wear and tear, or exposure.

Cost of regular use or maintenance service or parts, such as

gas, oil, lubricants, tune-up parts, and adjustments.

Any part or accessory which has been altered, modified,

misused, neglected, accidentally damaged or not properly

installed, maintained, stored or repaired not in accordance

with the instructions in the owner’s manual.

Repair due to normal wear and or any wear items such as

shear pins, bolts, belts, etc.

Expedited freight fee services for replacement parts.

Shear bolts and shear pins are to be considered as a

preventive measure not as an assured protection, any

damages resulting from the lack of shear bolts breakage are

not covered.

Damages due to product being installed on a vehicle other

than stipulated in owner’s manual.

NOTE: All warranty work must be performed by an authorized

dealer using original (manufacturer) replacement parts.

Owner’s Responsibilities:

BERCOMAC’s defective equipment or part must be returned

to an authorized dealer within the warranty period for repairs.

In the event that defective merchandise must be returned to

manufacturer for repairs, freight fees are prepaid and a written

authorization from BERCOMAC must be obtained by dealer

prior to the shipment. This warranty extends only to

equipment operated under normal conditions. To validate a

warranty claim, it is the user’s responsibility to maintain and

service the unit as specified in the owner’s manual or to have

the unit serviced at their dealer at their expense.

General Conditions:

The sole liability of BERCOMAC with respect to this warranty

shall be strictly and exclusively repair and replacement as

mentioned herein. BERCOMAC shall not have any liability for

any other costs, loss or damage, including but not limited to,

any incidental or consequential loss or damage.

Taking advantage of the warranty does not in any way extend

the length or renewal of the warranty.

In particular, without being limited to, BERCOMAC shall have

no liability or responsibility for:

Travel time, overtime, after hours time or other

extraordinary repair charges or relating to repairs and or

replacements outside of normal business hours.

Rental of like or similar replacement equipment during the

period of any, repair or replacement work.

Any communicating or travel charges.

Loss or damage to person or property other than that

covered by the terms of this warranty.

Any claims for lost revenue, lost profit or any similar costs

as a result of damage or repair.

Attorney’s fees.

BERCOMAC’s responsibility in respect to claims is limited to

making the required repairs or replacement without charge up

to our maximum labor rates and pre-established times and no

claim of breach of warranty shall be cause for cancellation or

rescission of the contract of sale of any product or accessory.

In no event recovery of any kind be greater than the amount of

the purchase price of the product sold.

This warranty gives you specific legal rights. You may also

have other rights, which vary from state to state.

NOTE: Bercomac reserves the right to change or improve the design of any part or accessory without assuming any obligation to modify

any product previously manufactured.

Instructions for Obtaining Warranty Services:

Contact dealer where equipment was purchased or any other BERCO service dealer to arrange service at their dealership. Requests for

warranty claims must be carried out through the same distribution network used to purchase the product.. Don't forget to bring your proof

of purchase (sales receipt) to the BERCOMAC dealer.

TABLE OF CONTENTS

INTRODUCTION ...................................................................................................................................................... 2

SAFETY PRECAUTIONS ........................................................................................................................................ 3

SAFETY DECALS .................................................................................................................................................... 5

ASSEMBLY

Tools Required ........................................................................................................................................... 6

Step 1: Subframe Installation ..................................................................................................................... 6

Step 2: Installation the Winch Control Switch ........................................................................................... 10

Step 3: Drive Mechanism Installation ........................................................................................................ 13

OPERATION & MAINTENANCE

Controls ....................................................................................................................................................... 16

Maintenance ............................................................................................................................................... 16

Belt Replacement ....................................................................................................................................... 16

Verify Tire Pressure .................................................................................................................................... 16

DISMOUNTING & STORAGE

Dismounting ................................................................................................................................................ 16

Storage ........................................................................................................................................................ 16

TROUBLE SHOOTING ............................................................................................................................................ 17

PARTS BREAKDOWN AND PARTS LIST

Compact Drive Mechanism 700528-1 ...................................................................................................... 19

Northeast Drive Mechanism 700529-1 ..................................................................................................... 21

Subframe 700527-2 ................................................................................................................................... 23

Winch 106125 ............................................................................................................................................... 26

TORQUE SPECIFICATION TABLE ....................................................................................................................... 27

ATTACHMENTS ....................................................................................................................................................... 28

PAGE

INTRODUCTION

TO THE PURCHASER

This new accessory was carefully designed to give years of dependable service. This manual has been provided to

assist in the safe operation and servicing of your attachment.

NOTE: All photographs and illustrations in the manual may not necessarily depict the actual models or attachment, but

are intended for reference only and are based on the latest product information available at the time of publication.

Familiarize yourself fully with the safety recommendations and operating procedures before putting the machine to

use. Carefully read, understand and follow these recommendations and insist that they be followed by those who will

use this attachment.

THIS SAFETY ALERT SYMBOL IDENTIFIES AN IMPORTANT SAFETY MESSAGE IN THIS

MANUAL THAT HELPS YOU AND OTHERS AVOID PERSONAL INJURY OR EVEN DEATH.

DANGER, WARNING, AND CAUTION ARE SIGNAL WORDS USED TO IDENTIFY THE LEVEL OF

HAZARD. HOWEVER, REGARDLESS OF THE HAZARD, BE EXTREMELY CAREFUL.

DANGER: Signals an extreme hazard that will cause serious injury or death if recommended precautions

are not followed.

WARNING: Signals a hazard that may cause serious injury or death if the recommended precautions are

not followed.

CAUTION: Signals a hazard that may cause minor or moderate injury if the recommended precautions are

not followed.

Record your attachment serial number and purchase date in the section reserved below (there is no serial number on

the subframe). Your dealer requires this information to give you prompt, efficient service when ordering replacement

parts. Use only genuine parts when replacements are required.

If warranty repairs are required please present this registration booklet and original sales invoice to your selling dealer

for warranty service.

This manual should be kept for future reference.

Please check if you have received all the parts for your kit with the list of the

bag and the list of the box.

SERIAL NUMBER : ___________________________

(IF APPLICABLE)

MODEL NUMBER: ___________________________

PURCHASE DATE : ___________________________

SAFETY PRECAUTIONS

Careful operation is your best insurance against an accident. Read this section carefully before operating the vehicle

and accessory. This accessory is capable of amputating hands and feet and throwing objects. Failure to observe the

following safety instructions could result in serious injury. All operators, no matter how experienced they may be,

should read this and other manuals related to the vehicle and accessory before operating. It is the owner's legal

obligation to instruct all operators in safe operation of the accessory.

GLOSSARY:

In this manual, right and left sides are determined by

sitting on the seat of the vehicle facing forward.

In this manual, "accessories" means attachments

(snowblower, rotary broom, blade etc.) that you install

on the vehicle (lawn tractors, A.T.V. s etc).

TRAINING:

This symbol, "Safety Alert Symbol", is used

throughout this manual and on the

accessory’s safety labels to warn of the

possibility of serious injury. Please take

special care in reading and understanding

the safety precautions before operating the

vehicle and accessory.

1. Read this owner's manual carefully. Be thoroughly

familiar with the controls and proper use of the

vehicle and accessory. Know how to stop the unit

and disengage the controls quickly.

2. Never allow children to operate the vehicle nor the

accessory. Never allow adults to operate the vehicle

nor the accessory without proper instructions.

3. No one should operate the vehicle nor the

accessory while intoxicated or while taking

medication that impairs the senses or reactions.

4. Keep the area of operation clear of all people,

particularly small children and pets.

PREPARATION:

1. Thoroughly inspect the area where the accessory

is to be used and remove door mats, all foreign

objects and the like.

2. For motorized accessories, disengage all clutches

and shift into neutral before starting engine.

3. Do not operate the accessory without wearing

adequate winter outer garments. Avoid loose fitting

clothing that can get caught in moving parts. Wear

footwear that will improve footing on slippery

surfaces.

4. Handle fuel with care, it is highly flammable.

a) Use approved fuel container.

b) Never add fuel to a running engine or hot engine.

c) Fill fuel tank outdoors with extreme care. Never fill

fuel tank indoors.

d) Never fill containers inside a vehicle, or on a

truck or a trailer bed with a plastic liner. Always

place containers on the ground, away from your

vehicle, before filling.

e) When practical, remove gas-powered

equipment from the truck or trailer and refuel it

on the ground. If this is not possible, then refuel

such equipment on a trailer with a portable

container, rather than from a gasoline

dispenser nozzle.

f) Keep the nozzle in contact with the rim of the

fuel tank or container opening at all times, until

refueling is complete. Do not use a nozzle lock-

open device.

g) Replace fuel cap securely and wipe up spilled

fuel.

h) If fuel is spilled on clothing, change clothing

immediately.

5. Never attempt to make any adjustments while the

engine (motor) is running (except when specifically

recommended by manufacturer).

6. Let the vehicle and accessory adjust to outdoor

temperatures before using.

7. Never use an accessory without proper guards,

plates, or other safety protective devices in place

8. Always make sure to wear the appropriate safety

equipment required (glasses, muffs, mask…) for

each type of product. See operation section.

9. Always make sure of having safe traction on the

vehicle by using the recommended accessories

(chains, A.T.V. tracks, counterweights…). See

operation section.

10. Always make sure the all components are correctly

installed. (driveline securely attached and locked at

both ends, belts properly installed…)

11. Always handle the winch cable with thick leather

gloves.

12. Never modify the accessory or any part without

the written consent from the manufacturer.

OPERATION:

1. Do not put hands or feet near, under or inside rotating

parts.

2. Exercise extreme caution when operating on or

crossing gravel drives, walks or roads. Stay alert for

hidden hazards or traffic. Do not carry passengers.

3. After striking a foreign object, stop the engine (motor),

disconnect the wire from the spark plug(s) and keep

wire away to prevent accidental starting. Thoroughly

inspect the accessory for any damage and repair

damage before restarting and using the accessory.

4. If the unit should start to vibrate abnormally, stop the

engine (motor) and check immediately for the

cause. Vibration is generally a warning of trouble.

5. Take all possible precautions when leaving the

vehicle unattended. Disengage the power take-off,

lower the attachment, place the transmission into

neutral, set the parking brake, stop the engine and

remove the contact key.

6. Do not run the engine indoors, except when starting

the engine and for transporting in or out of the

building. Do not operate or let motor run in a storage

area without ventilation because gas contains

carbon monoxide which is odorless, colorless and

can cause death.

7. Never use the accessories across the face of

slopes, go from top to bottom. Exercise extreme

caution when using equipment on slopes. Do not

attempt to clear a steep slope.

8. Never tolerate bystanders in the working zone.

Never use an accessory in the direction of

bystanders, it might throw gravel or debris that can

hurt people or damage property.

9. Never operate the accessory at high transport

speeds on slippery surfaces. Use care when

backing up.

10. Do not carry passengers.

11. Disengage power to the accessory when it is

transported or not in use.

12. Never operate the accessory without good visibility

or light.

13. Keep the accessory away from heat sources or

flames.

14. Never handle the winch cable or hook while in

tension.

MAINTENANCE AND STORAGE

1. When cleaning, repairing or inspecting the vehicle

and accessory, make certain that all moving parts

have stopped. For gasoline engine, disconnect wire

from the spark plug(s) and keep wire away to

prevent accidental starting.

2. Check all the bolts and components at frequent

intervals to make sure that they are properly

tightened.

3. Never store a motorized accessory with fuel in the

fuel tank inside a building where ignition sources are

present such as hot water and space heaters,

clothes dryers, and the like. Allow the engine to cool

before storing in any enclosure.

4. Always refer to the owner’s manual when you store

the accessory and vehicle for a prolonged or an

unspecified length of time.

5. Maintain or replace safety and instruction labels, as

necessary.

6 For winter accessories, (if applicable), let the engine

run for a few minutes after clean snow in order to

prevent the rotary parts from freezing.

7. Inspect the vehicle’s and accessory’s air filter (if

applicable) every day. Clean it or replace it as

necessary. Change the oil more often when working

in dusty conditions. See the vehicle’s and

accessory's owner’s manual.

THIS SYMBOL MEANS

DANGER !

BECOME ALERT !

YOUR SAFETY IS INVOLVED !

SAFETY PRECAUTIONS

SAFETY DECALS

REPLACE IF DECALS ARE DAMAGED

SEE PARTS BREAKDOWN FOR DECAL LOCATION

DECAL #105133

Failure to observe these instructions could lead to

severe injury or death.

To avoid injury to hands or fingers:

-Always keep hands clear of rope hook loop, ,hook and

fairlead opening during installation , operation and

when spooling in or out.

-Always use extreme caution when handling hook and

rope during spooling operations.

-Always wear heavy leather gloves when handling rope.

-Keep hands away from the hot surface.

ASSEMBLY

Install the left & right supports (item 2) on each side of

the vehicle.

Item # Description Action

1 Tractor shoulder screw Remove from both

sides of tractor.

2 Left & right support

(qty 2) Install on each side

as shown.

3 Lock washer

(qty 2) Insert on the bolt

(item 5) as shown.

4 Flat washer

(qty 2) Insert on the bolt

(item 5) as shown.

5 Hex bolt 1/2’’ x 1’’

(qty 2 ) Insert as shown.

6 Hex nut 1/2’’ thin,

(qty 2) Do not tighten.

NOTE: Save the tractor shoulder bolts in case you

reinstall the bumper.

IMPORTANT: TORQUE ALL BOLTS ACCORDING TO TORQUE SPECIFICATION TABLE WHEN STATED:

TIGHTEN FIRMLY.

THE WINCH KIT IS TO BE USED ONLY TO LIFT BERCO ACCESSORIES, ANY OTHER USE MAY CAUSE

DAMAGE TO THE VEHICLE.

This subframe may be used to install different attachments (see attachments page). Once installed, it may

remain permanently on your vehicle.

NOTE: It is not necessary to remove mower deck at this step.

STEP 1

SUBFRAME INSTALLATION:

Refer to parts breakdown section for parts

identification.

TOOLS REQUIRED:

Wrenches:1/2, 3/4, 5/16, 7/16, 9/16, 10mm

Ratchet

Sockets: 2/16, 1/2, 9/16, 3/4, 10mm

Cutting pliers

Pliers

Square head screwdriver: #2, #3

Please sort out and identify all the hardware before

starting installation. Lists for the hardware bag and for

the box are supplied in each.

Install the supports

Install the left & right supports (items 1 & 2) on each

side of the vehicle.

Item # Description Action

1 & 2 Left & right support Install as shown.

3 Hex bolt

5/16’’ x 1‘’ Insert in supports as

shown.

4 Hex bolt 5/16’’ x 1/2‘’

(qty 3) Insert in supports as

shown.

5 Hex nut 5/16’’

(qty 4) Install on bolts and

tighten firmly. Install the supports

INSTALLING THE REFLECTORS

IMPORTANT: When operating the tractor with the

front mounted attachment, install the two red-colored

adhesive reflectors on the rear vertical surface of the

tractor’s fender.

ASSEMBLY

NOTE: Remove tractor bolt (A) from under the foot rest

pad as shown.

Remove tractor bolt (B) from underneath the foot rest.

Keep the bolts in a safe place for future installation.

Install handle support (item 4).

Item # Description Action

1 Carriage bolt

5/16’’n.c. x 1 1/2’’ Insert as shown.

2 Flat washer Install as shown on

bolt.

3 Sleeve Insert on the bolt as

shown. *

4 Handle support Insert on the bolt as

shown

5 Flange nut

5/16’’ n.c. Do not tighten.

6 Carriage bolt

5/16’’ n.c. x 3/4’’ Insert as shown.

7 Flange nut

5/16’’ n.c Tighten firmly.

8 Plastic grommet Insert as shown.

9 Square head set

screw

5/16’’ n.c. x 1/2’’

Insert as shown.

NOTE: Tighten firmly all the nuts. Put the pad of the

foot rest in place.

* Do not use if there is a rubber bushing. Install handle support

Install the left & right braces (items 1 & 2) on each

side of the vehicle.

Item # Description Action

1 & 2 Left & right brace

(qty 2) Install on the inside

as shown.

3 Hex bolt

3/8’’ n.c. x 1‘’

(qty 4)

Insert the bolts as

shown (one inside

the other outside).

4 Nylon insert lock nut

3/8’’

(qty 4)

Insert on the bolts as

shown.

Tighten firmly.

NOTE: Tighten firmly the hex. bolts (item 5) on both

sides. Install the braces

For the 42’’ mower deck only: Remove the mower

deck stopper and keep in safe place.

NOTE 2: If your tractor has the muffler coming out the

front as shown in the drawing, please install the heat

shield as shown below.

If the muffler come out in another position, you do not

need the heat shield.

ASSEMBLY

Install the female hitch (item 1)

# Item Description Action

1 Female hitch Install between the

two supports.

2 Heat shield Install the heat

shield inside the

female hitch.*

3 Hex bolt 3/8 x 1’’

(qty 4) Insert as shown.

4 Flange nut 3/8’’

(qty 4) Tighten all the nuts

firmly.

* See NOTE 2 at top of page

Install the female hitch between the two supports

Install the spring (item 1)

# Item Description Action

1 Spring Install the spring

on the frame as

shown.

NOTE: The latch must move freely.

Install the spring as shown

ASSEMBLY

NOTE: Lift the front part of foot rest to remove tractor

bolt (item 1). Install the cab support (item 5).

# Item Description Action

1 Tractor bolt Remove from

tractor.

2 Carriage bolt

5/16’’n.c. x 1 1/2’’ Insert as shown.

3 Flat washer Install as shown on

bolt.

4 Sleeve Insert on the bolt as

shown.*

5 Cab support Insert on the bolt as

shown.

6 Flange nut 5/16’’ n.c. Tighten.

7 Square head set

screw 5/16 x 1/2’’ Insert in the hole of

the cab support.

NOTE: Keep the tractor bolt in a safe place for future

installation.

* Do not use if there is a rubber bushing. Install the cab support

ASSEMBLY

Install the winch control switch

STEP 2:

INSTALLATION OF THE WINCH CONTROL

SWITCH

Install the relay (item 1).

Item Description Action

1 Relay Install in an appropriate

area.

2 Metal screw

#12 x 3/4’’ (qty 4) Secure relay in place.

*3 Nylon tie wrap 8’’

(qty 4) See *

*If necessary use the nylon tie wraps to secure the

relay in place.

** Install in a sheltered place away from bad weather.

Install the relay

IMPORTANT

To prolong the winch cable’s life, release the winch control switch as soon as the accessory touches the

ground. This will keep the cable from tangling up which causes premature wear.

Before drilling the hole, check behind the dashboard

to make sure there is enough space to install the

switch.

Drill a 1/2’’ hole in the dashboard or an appropriate

place (see reference drawing). Stick the UP/DOWN

decal over the hole for the switch.

Insert the switch in the hole and secure in place with

the rubber boot.

NOTE: It is important to install the switch vertically.

Connect the wires as shown.

When the switch is raised, the winch must lift the

accessory. If you prefer the contrary, invert the green

and black wires.

Connect the wires

Up / Down decal

ASSEMBLY

CONNECTING THE WIRES

NOTE: The posts on the relay are identified by

numbers. (1-2-3-4).

Install the wires from the winch on the posts of the

relay.

Red wire (+) on post #3.

Black wire (-) on post #4.

Connect the red wire from the winch (limit switch) with

the green wire from the relay.

Connect the wires

IDENTIFY THE IGNITION WIRE:

Place the clip of the Hi / Low tester on the negative

post (-) on the battery or a metal surface without any

paint.

Turn the ignition key to the position: Accessory.

Insert the tip of the tester in a hole at the back of the

starter (switch) make sure to touch the metal part of

the wire (on most tractors, it is the A1 terminal on the

ignition switch that is used for accessories. Before

connection, verify with HI/LOW tester).

If the tester’s light turns on, turn the ignition key to the

position, Off. The light must turn off.

You have identified the ignition wire, if not repeat the

operation on another wire.

INSTALL THE CONTROL WIRE:

Join the ignition wire and the red wire from the winch

control (item 1) with the instant connector (item 2).

Connect the black wire of the winch control (item 3) to

the black wire on the relay.

Connect the green wire of the winch control (item 3)

with the red wire of the winch (limit switch).

Connect the ignition wire

ASSEMBLY

CAUTION

FOR YOUR SECURITY:

Read and follow the safety precautions for the

battery in the vehicle’s manual.

CONNECT THE WIRES ON THE BATTERY:

Connect the wires from the relay to the vehicle’s

battery.

The red wire (+) on the positive post of the battery

(item 1).

The black wire (-) on the negative post of the battery

(item 2).

Make sure to tighten the nuts on the posts.

TIE ALL THE WIRES:

NOTE: Make sure the wires from the control

assembly do not interfere with anything on the tractor

nor come into contact with any heating, electrical or

removable elements of the tractor.

Tie the wires with four nylon tie wraps included in the

kit.

Connect the relay wires to the battery

Install the heat shield (item 1).

# Item Description Action

1 Heat shield Install as shown.

2 Hex bolts

1/4 x 1/2’’

(qty 2)

Tighten firmly.

Install the heat shield

VERY IMPORTANT:

Make sure the cable winds up and unrolls as shown

in the figure (cable under the spool).

Lubricate the winch cable and the drum periodically

with grease.

If the winch cable does not wind up from the

bottom of spool as shown, the limit switch will not

work and may cause damage to the subframe,

winch and accessory.

ASSEMBLY

STEP 3:

DRIVE MECHANISM INSTALLATION:

WARNING

TO PREVENT INJURIES:

It is the person who installs the drive mechanism

responsibility to make sure that when the clutch

is disengaged that all moving parts stop.

For more information, do not hesitate to contact

the technical support.

WARNING

TO PREVENT INJURIES:

Stop the motor.

Apply parking brake.

Remove the ignition key.

Disconnect the wire from the spark plug(s) and

keep away from spark plug(s) to prevent accidental

starting.

NOTE: You must remove mower deck to install

the drive mechanism.

Install the drive mechanism (item 1).

# Item Description Action

1 Back of drive

mechanism Hook on the tractor frame,

right side.

2 Front of drive

mechanism Install between the

supports.

4 Pin

(qty 2) Insert as shown.

On the right side, pin and

sleeve (item 3) from the

outside.

On the left side, and pin

from the inside.

5 Hair pin

(qty 2) Secure the pins.

6 Carriage bolt

5/16’’ x 1’’ Insert in the back of the

drive as shown.

7 Bracket Install on the bolt as

shown and on the tractor

frame.

8 Knob Tighten to lock the drive

frame in place. Install drive mechanism

For tractors with Electric Clutch:

Install the belt on the engine pulley of the vehicle.

Check the tension on the spring.

If necessary, adjust the tension by moving the

adjustment rod (item 1) and tighten the set screw

(item 2).

No modifications to be done

ASSEMBLY

For tractors with Manual Clutch activated by a

cable:

Install the tractor’s manual clutch cable .

* Remove the spring.

# Item Description Action

1 Spring from the clutch

cable Install as shown in

the hole on the

tension pulley.

2 Clutch cable Insert in the slot on

the adjustment rod.

3 Hair pin 2mm Secure the cable.

4 Adjustment rod Slide towards the

back to apply enough

tension on the spring.

5 Square head set

screw 5/16 x 1/2’’ Secure the

adjustment rod.

Install the belt on the engine pulley of the vehicle.

Check the tension on the spring.

If necessary, adjust the tension by moving the

adjustment rod and tighten the set screw.

Install the manual clutch cable

Secure clutch cable

Install the cable clip (item 2).

# Item Description Action

1 Hex bolt.

1/4 x 1/2’’ Install as shown

(choose a hole)

2 Cable clip Insert the cable in

the clip and insert

on bolt as shown.

3 Flange nut 1/4’’ Tighten firmly.

ASSEMBLY

If applicable, you can remove or add a flat washer

(item 1) on the tension pulley (item 2) for a better

adjustment.

Engage and disengage the clutch a few times and

make sure the belt does not touch the belt guide in

any place when the drive mechanism is engaged.

VERIFICATION OF THE BELT AND PULLEY

ALIGNMENT:

WARNING

TO PREVENT INJURIES:

It is the person who installs the drive mechanism

responsibility to make sure that when the clutch

is disengaged that all moving parts stop.

For more information, do not hesitate to contact

the technical support.

WARNING

TO PREVENT INJURIES:

do this verification when the engine of the vehicle

is not running.

Adjust the pulleys

OPERATION & MAINTENANCE

CAUTION

Read the vehicle Owner’s Manual carefully. Be

thoroughly familiar with the controls & proper

use of the attachment. Know how to stop the

attachment quickly.

IMPORTANT:

THE WINCH KIT IS TO BE USED ONLY TO LIFT

BERCO ACCESSORIES, ANY OTHER USE MAY

CAUSE DAMAGE TO THE VEHICLE.

MAINTENANCE

a) Check mounting bolts at frequent intervals for

proper tightness to be sure equipment is in safe

working condition.

b) Apply oil at all pivot points.

c) To prolong the life span of the winch, make sure the

snap mount switch works well.

BELT REPLACEMENT

Belt for the accessories:

SEE ATTACHMENT OWNER'S MANUAL

(SNOWBLOWER AND BROOM) FOR REPLACING

INSTRUCTIONS.

Drive Mechanism Belt:

a) Dismount the drive mechanism.

b) Remove the bolt which retains the tension pulley.

c) Replace the belt and re-install the tension pulley.

Before tightening make sure the belt guide does

not touch the belt at any time.

d) Re-install the drive mechanism.

e) Check the alignment of the belt that joins the

drive mechanism to the engine pulley.

VERIFY TIRE PRESSURE:

Tire pressure must be even on both sides of the

tractor according to the vehicle’s owner’s manual.

DISMOUNTING & STORAGE

DISMOUNTING

SEE ATTACHMENT OWNER'S MANUAL

(SNOWBLOWER, BROOM AND BLADE) FOR

DISMOUNTING INSTRUCTIONS.

a) Dismount the attachment.

b) Remove the rear counterweight when you remove

the front attachment (if applicable).

c) Remove the belt from the engine pulley.

d) Dismount the drive mechanism by supporting it in

your hand. Carefully lower to the ground.

Manual clutch activated by cable:

Unhook cable shield by removing the hair pin.

Unhook spring. Pull out drive mechanism from

underneath tractor.

e) You may leave the subframe on tractor all year long

or remove it if preferred.

f) Reinstall mower if needed.

STORAGE

a) Clean and paint all parts from which paint has worn.

b) Apply oil at all pivot points.

c) Inspect and replace all defective parts before using

again.

CONTROLS

IMPORTANT:

In order to avoid draining the battery of the

vehicle, always start the engine before using the

winch.

THE WINCH CONTROL SWITCH

Push up or down the winch control switch to lift or

lower the accessory to the ground.

There is a limit switch stopper that limits the lifting.

Always prestretch cable and respool under load

before installing the hook on the accessory. A tightly

wound cable reduces chances of binding, which can

cause damage to the cable.

To prolong the winch cable’s life, release the winch

control switch as soon as the accessory touches the

ground. This will keep the cable from tangling up,

causing premature wear of the cable.

WINCH CABLE MAINTENANCE

To reduce the risk of cable failure during the season,

we recommend changing the winch cable every year.

Lubricate the winch cable and the drum periodically

with grease.

Install the new winch cable as shown in figure in the

parts breakdown.

TROUBLESHOOTING

* Please refer to parts breakdown section for parts identification.

PROBLEM POSSIBLE CAUSES CORRECTIVE ACTION

Winch runs backwards or stays Winch wires reversed. Recheck wiring.

stuck in up position. Switch wires reversed. Recheck wiring.

Switch installed incorrectly. Check switch installation.

Battery wires reversed. Recheck wiring.

Winch cable is not winded up from

the bottom of spool. Wind winch cable from the bottom

of the spool. (see assembly section

in subframe manual)

Winch will not operate or runs in one

direction only. Vehicle’s ignition switch is at OFF

position. Turn vehicle’s ignition switch at ON

position.

Broken wires or bad connection. Check for poor connections.

Control switch is inoperative. Replace control switch.

Relay or breaker is damaged. Replace the relay or breaker.

Limit switch is damaged or wires

disconnected from limit switch. Replace limit switch or verify wire

connections on limit switch.

Winch is damaged. Replace or repair winch.

Winch runs but with insufficient power

or line speed. Weak battery. Recharge or replace battery.

Check charging system

Poor battery connection. Check battery terminals for

corrosion. Clean when required.

Winch is damaged. Replace or repair winch.

Winch cable breaking prematurely. Frequently stopping the winch when

accessory is going down. Doing complete up and down cycles

and avoid stopping midway.

Cable tangling up. Release the control switch as soon

as the accessory touches the

ground.

Winch drum and cable wearing

prematurely. Insufficient lubrication of winch drum

and cable. Lubricate winch drum and cable

periodically with grease.

Winch does not hold the accessory in

up position. Winch is damaged. Replace or repair winch.

TROUBLESHOOTING

HOW TO KNOW POINTS TO CHECK

Poor connections. Recheck wiring with the owner's manual

HI/LOW voltage tester does not work. Connect it on battery posts (+ and -) of a functional battery.

If there is no light, the tester is damaged.

The control switch inoperative. Test both connectors with HI/LOW voltage tester.

If light comes ON or the relay is clicking in both positions (UP &

DOWN), the control switch is operative.

Relay is damaged If there is voltage on battery wire posts 1 & 2 on the relay and no

voltage on posts 3 & 4 when control switch is activated and relay is

clicking in both directions, the relay is defective. (see relay assembly

section in owner’s manual for relay post identification). Check

connections with HI/LOW voltage tester.

Winch is damaged The ultimate test is to connect the winch directly to the battery and

reverse the wires to test both directions. If the winch doesn't work, it is

damaged.

The limit switch is damaged. When the limit switch is pushed or stuck inside, the winch can't raise

the accessory, only lower it. If not working properly replace it.

The breaker is damaged. Place clip of the HI / LOW voltage tester on negative (-) post of the

battery. Check the voltage with the tip of the tester on both terminals

of the breaker. If voltage only on 1 terminal replace the breaker.

(sometimes it could take a few minutes for the breaker to

automatically reset itself)

La page charge ...

Bercomac 700527-2 700528-1 Manuel utilisateur

Marque: Bercomac

Modèle: 700527-2 700528-1

Taper: Manuel utilisateur

Ce manuel convient également à

700527-2 700529-1

Télécharger le PDF

rapport

dans d''autres langues

English: Bercomac 700527-2 700528-1 User manual

Documents connexes

Autres documents

Berco 700529-1 Le manuel du propriétaire