Shure AD1 Mode d'emploi

Catégorie
Radios bidirectionnelles
Taper
Mode d'emploi
AD1
Bodypack Transmitter
AD1 Axient Digital Bodypack Transmitter User Guide
Version: 8 (2020-A)
Shure Incorporated
2/24
Table of Contents
AD1Bodypack Transmitter 3
WARNING 3
AD1 Axient Digital Bodypack Transmitter 3
Features 3
Included Components 4
Optional Accessories 4
AD1 Transmitter Overview 4
Transmitter Controls 6
Locking the Interface 6
Home Screen Display 7
Battery Installation 7
Setting the AA Battery Type 8
AA Battery Installation 8
Shure SB900A Rechargeable Battery 9
Battery Life 9
Checking Battery Info 9
Important Tips for Care and Storage of Shure Recharge
able Batteries 10
AA Batteries and Transmitter Runtime 10
Menu Parameters 11
Tips for Editing Menu Parameters 11
Menu Map 12
Menu Parameter Descriptions 12
Radio Menu 12
Audio Menu 12
Utilities Menu 13
IR Sync 14
Setting the Frequency Manually 14
Updating Firmware 15
Firmware Versioning 15
Updating the Transmitter 15
Wearing the Bodypack Transmitter 15
RF Mute 16
Safe Start 16
Input Overload 17
Matching Audio Levels with Offset 17
Tone Generator 17
Specifications 18
Input Connector Diagrams 20
Frequency Bands and Transmitter RF Power 20
LICENSING INFORMATION 22
Australia Warning for Wireless 23
Certifications 23
Information to the user 23
Shure Incorporated
3/24
AD1
Bodypack Transmitter
WARNING
Battery packs may explode or release toxic materials. Risk of fire or burns. Do not open, crush, modify, disassemble, heat
above 140°F (60°C), or incinerate.
Follow instructions from manufacturer
Only use Shure charger to recharge Shure rechargeable batteries
WARNING: Danger of explosion if battery incorrectly replaced. Replace only with same or equivalent type.
Never put batteries in mouth. If swallowed, contact your physician or local poison control center
Do not short circuit; may cause burns or catch fire
Do not charge or use battery packs other than Shure rechargeable batteries
Dispose of battery packs properly. Check with local vendor for proper disposal of used battery packs.
Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like
WARNING: Danger of explosion if incorrect battery replaced. Operate only with AA batteries.
Note: Use only with the included power supply or a Shure-approved equivalent.
AD1 Axient Digital Bodypack Transmitter
AD series bodypack transmitters deliver impeccable audio quality and RF performance with wide-tuning, High Density (HD)
mode, and encryption. The transmitter features durable metal construction, AA or SB900A rechargeable power (with dockable
charging), and TA4 or LEMO3 connector options.
Features
Performance
20 Hz to 20 kHz range with flat frequency response
Automatic input staging optimizes gain setting
AES 256-bit encryption-enabled for secure transmission
>120 dB dynamic range
100 meter (300 feet) line-of-sight operating range
Selectable modulation modes optimize performance for spectral efficiency
Standard – optimal coverage, low latency
High density – dramatic increase in max system channel count
Built-in tone generator and RF markers to facilitate walk-testing
Switchable Power Levels = 2/10/35 mW (region dependent)
Frequency Diversity selection using two bodypacks
Design
TA4 or LEMO3 audio connector option
Shure Incorporated
4/24
Backlit LCD with easy to navigate menu and controls
Rugged metal construction
Flexible ¼ wave antenna
Menu and power lockout
Power
Over 8 hours continuous use with 2 x AA alkaline batteries
Shure SB900A lithium-ion rechargeable battery provides extended battery life, precision metering, and zero memory effect
External charging contacts for docked charging
Included Components
AA alkaline batteries (2) 80B8201
¼ wave antenna Varies by Region
Threaded TAF4 adapter WA340
Zipper bag 26A13
Belt clip 44A12547
Optional Accessories
Bodypack rechargeable lithium-ion battery SB900A
Y-Cable for bodypack transmitters AXT652
LEMO Y-cable for bodypack transmitters AXT652LEMO3
Instrument cable WA302
Replacement belt clip 44A12547
Instrument cable with right angle 1/4" connector WA304
Mute Switch for Bodypack WA661
Mute Switch for 2 Bodypacks WA662
AD1 Transmitter Overview
RF Antenna
For RF signal transmission.
Display
Shure Incorporated
5/24
View menu screens and settings. Press any control button to activate the backlight.
Infrared (IR) Port
Align with the receiver IR port during an IR Sync for automated transmitter tuning and setup.
Control Buttons
Use to navigate through parameter menus and to change settings.
Battery Compartment
Requires two AA batteries or Shure SB900A rechargeable battery.
AA Battery Adapter
Use to secure AA batteries. Remove when using a Shure SB900A battery.
SMA Connector
Connection point for RF antenna.
Power Switch
Powers the unit on or off.
Power LED
Green = unit is powered on
Red = low battery, Mute Mode enabled, input overload, or battery error (see Troubleshooting)
Input Jack
Connects to a 4-Pin Mini Connector (TA4F) microphone or instrument cable.
Note: A LEMO connector model variation of this transmitter is available.
Shure Incorporated
6/24
Transmitter Controls
Use the controls to navigate through parameter menus and change values.
exit Acts as a 'back' button to return to previous menus or parameters without confirming a value change
enter Enters menu screens and confirms parameter changes
∨∧ Use to scroll through menu screens and to change parameter values
Tip: Use the following shortcuts for quick setup:
Hold the
button while powering on to lock or unlock the transmitter controls.
Hold the exit button while powering on to enter the Safe Start menu.
Shure Incorporated
7/24
1.
2.
Locking the Interface
Lock transmitter interface controls to prevent accidental or unauthorized changes to parameters. The lock icon appears on the
home screen when a lock is enabled.
From the Utilities menu, navigate to Locks and select one of the following lock options:
None: The controls are unlocked
Power: The power switch is locked
Menu: The menu parameters are locked
All: The power switch and menu parameters are locked
Press enter to save.
Tip: To quickly unlock a transmitter: Press enter twice, select None, and press enter.
Home Screen Display
The home screen shows transmitter information and status.
There are four pieces of information that you can choose to see on the home screen. Use the arrow buttons to select one of
the following choices:
Name
Frequency Setting
Group (G) and Channel (C)
Device ID
The following icons indicate transmitter settings:
Battery runtime in hours and minutes or bar display
Key: Displayed when encryption is enabled
Lock: Displayed when controls are locked. Icon will flash if
access is attempted to a locked control (power or menu).
STD: Standard Transmission Mode
HD: High Density Transmission Mode
RF Mute Engaged: Displayed when RF output is muted
Shure Incorporated
8/24
1.
2.
3.
Battery Installation
Accessing the Battery
Compartment
Press the side tabs on the bodypack and open the battery door as shown to access the bat
tery compartment.
Installing Batteries
AA Batteries: Place batteries (note polarity markings) and AA Adaptor as shown and
close the door
Shure SB900A Battery: Place battery as shown (note polarity markings). Remove the
AA adapter and set it aside. Close the door to secure the battery.
Note: If using AA batteries, set the battery type using the transmitter menu.
Setting the AA Battery Type
To ensure accurate display of transmitter runtime, set the battery type in the transmitter menu to match the installed AA battery
type.
Note: If a Shure SB900A rechargeable battery is installed, selecting a battery type is not necessary and the battery type will display Shure.
Navigate to the Utilities and select Battery.
Use the ▼▲ buttons to select the installed battery type:
Alkaline = Alkaline
NiMH = Nickel Metal Hydride
Lithium = Lithium Primary
Press enter to save.
AA Battery Installation
Fully insert the batteries as shown to ensure proper battery contact and to allow the door to latch securely.
Shure Incorporated
9/24
Shure SB900A Rechargeable Battery
Shure SB900A lithium-ion batteries offer a rechargeable option for powering the transmitters. Batteries quickly charge to 50%
capacity in one hour and reach full charge within three hours.
Single chargers and multiple bay chargers are available to recharge the Shure batteries.
Caution: Only charge Shure rechargeable batteries with a Shure battery charger.
Battery Life
UHF 1.x
2mW/10mW 35 mW 2 mW/10mW 30mW
SB900A 9 hours 4:30 hours 6 hours 5 hours
alkaline 8 hours 3:30 hours 5:30 hours 3:45 hours
The values in this table are typical of fresh, high quality batteries. Battery runtime varies depending on the manufacturer and
age of the battery.
Checking Battery Info
When using a Shure rechargeable battery, the receiver and transmitter home screens display the number of hours and minutes
remaining.
Detailed information for the battery is displayed Battery menu of the transmitter: Utilities > Battery
Battery: The chemistry type of for the installed battery (Shure, Alkaline, Lithium, NiMH)
Bars: Indicates the number of bars displayed
Time: Battery runtime
Charge: Percentage of charge capacity
Health: Percentage of current battery health
Cycle Count: Total of the number of charging cycles for the installed battery
Temperature: Battery temperature reported in Celsius and Fahrenheit
Shure Incorporated
10/24
Important Tips for Care and Storage of Shure Rechargeable Batteries
Proper care and storage of Shure batteries results in reliable performance and ensures a long lifetime.
Always store batteries and transmitters at room temperature
Ideally, batteries should be charged to approximately 40% of capacity for long-term storage
Periodically clean the battery contacts with alcohol to maintain ideal contact
During storage, check batteries every 6 months and recharge to 40% of capacity as needed
For additional rechargeable battery information, visit www.shure.com.
AA Batteries and Transmitter Runtime
Transmitters are compatible with the following AA battery types:
Alkaline
Nickel Metal Hydride (NiMH)
Lithium Primary
A 5segment battery indicator representing the charge level of the transmitter battery is displayed on the screens of the trans
mitter and receiver. The following table contains the approximate remaining transmitter runtime in hours:minutes.
Alkaline Batteries
Battery Indicator
Battery Runtime (hours:minutes)
UHF 1.x
2 mW/10
mW
35
mW
2 mW
/10
mW
30
mW
8:00 to 6:00
3:30
to
3:00
5:30 to
4:15
3:45
to
3:00
6:00 to 4:00
3:00
to
2:00
4:15 to
3:00
3:00
to
2:15
4:00 to 1:45
2:00
to
1:30
3:00 to
1:45
2:15
to
2:00
<1:45 <1:30 <1:45 <2:00
Shure Incorporated
11/24
Battery Indicator
Battery Runtime (hours:minutes)
UHF 1.x
2 mW/10
mW
35
mW
2 mW
/10
mW
30
mW
<0:45 <0:45 <0:45 <0:45
<0:15 <0:15 <0:15 <0:15
Menu Parameters
The Main menu organizes the available transmitter parameters into three sub-menus:
Radio
Audio
Utilities
Tip: Use the arrow buttons to scroll between the sub-menus.
Tips for Editing Menu Parameters
To access the menu options from the home screen, press the enter button. Use the arrow buttons to access additional
menus and parameters.
A menu parameter will blink when editing is enabled
To increase, decrease or change a parameter, use the arrow buttons
To save a menu change, press enter
To exit a menu without saving a change, press exit
Shure Incorporated
12/24
Menu Map
Menu Parameter Descriptions
Radio Menu
Freq
Press the enter button to enable editing of a group (G:) channel (C:) or frequency (MHz). Use the arrow buttons to adjust
the values. To edit the frequency, press the enter button once to edit the first 3 digits, or twice to edit the second 3 digits.
Power
Higher RF power settings can extend the range of the transmitter.
Note: Higher RF power settings decrease battery runtime.
Output
Sets the RF output to On or Mute.
On: RF signal is active
Mute: RF signal is inactive
Audio Menu
Pad
Adjust the pad to avoid overloading the audio input. Select -12 dB or Off.
Offset
Adjust Offset level to balance mic levels when using two transmitters or when assigning multiple transmitters to receiver
slots. Adjustment range: -12 dB to +21 dB.
Polarity
Shure Incorporated
13/24
Selectable polarity assignment for the audio input connector:
Pos: Positive pressure on microphone diaphragm produces positive voltage on pin 2 (with respect to pin 3 of XLR output)
and the tip of the TRS output.
Neg: Positive pressure on microphone diaphragm produces negative voltage on pin 2 (with respect to pin 3 of XLR output)
and the tip of the TRS output.
Mute
When enabled, the power switch is configured as a mute switch for the audio:
Power switch on: Audio signal on
Power switch off: Audio signal muted
Exit mute mode to return the power switch to its normal functionality.
Tone Gen
Transmitter will generate a continuous test tone:
Freq: The tone can be set to 400 Hz or 1000 Hz.
Level: Adjusts the output level of the test tone.
Utilities Menu
Device ID
Assign a device ID of up to 9 letters or numbers.
Locks
Locks the transmitter controls and power switch.
None: The controls are unlocked
Power: The power switch is locked
Menu: The menu parameters are locked
All: The power switch and menu parameters are locked
Marker
When enabled, press the enter button to drop a marker in Wireless Workbench.
Battery
Displays battery information:
Battery Life: Runtime reported in bar display and time (hours:minutes)
Charge: Percentage of charge capacity
Health: Percentage of current battery health
Cycle Count: Total of the number of charging cycles for the installed battery
Temperature: Battery temperature reported in Celsius and Fahrenheit
About
Displays the following transmitter information:
Model: Displays the model number
Band: Displays the tuning band of the transmitter
FW Version: Installed firmware
Shure Incorporated
14/24
1.
2.
3.
4.
5.
1.
2.
3.
4.
HW Version: Hardware version
Serial Num: Serial number
Reset All
Restores all transmitter parameters to factory settings.
IR Sync
Use IR Sync to form an audio channel between the transmitter and receiver.
Note: The receiver band must match the band of the transmitter.
Select a receiver channel.
Tune the channel to an available frequency using group scan or manually turn to an open frequency.
Power on the transmitter.
Press the SYNC button on the receiver.
Align the IR windows between the transmitter and the receiver so that the IR LED illuminates red. When complete,
Sync Success! appears. The transmitter and receiver are now tuned to the same frequency.
Note:
Any change to the encryption status on the receiver (enabling/disabling encryption) requires a sync to send the settings to the
transmitter. New encryption keys for the transmitter and receiver channel are generated on every IR sync, so to request a new
key for a transmitter, perform an IR sync with the desired receiver channel.
Setting the Frequency Manually
The transmitter can be manually tuned to a specific group, channel, or frequency.
Navigate to the Radio menu and select Freq.
Scroll to select G: and C: to edit the group and channel, or select the frequency parameter (MHz). When editing the fre
quency, press enter once to edit the first 3 digits, or twice to edit the last 3 digits.
Use the ∧∨ buttons to adjust the group, channel, or frequency.
Press enter to save, and then press exit when finished.
Shure Incorporated
15/24
1.
2.
3.
4.
Updating Firmware
Firmware is embedded software in each component that controls functionality. Periodically, new versions of firmware are devel
oped to incorporate additional features and enhancements. To take advantage of design improvements, you can upload and in
stall new versions of the firmware by using the Shure Update Utility. The Shure Update Utility is available for download from
http://www.shure.com/.
Firmware Versioning
When performing an update, first download firmware to the receiver, and then update transmitters to the same firmware version
to ensure consistent operation.
The firmware numbering for Shure devices uses the following format: MAJOR.MINOR.PATCH (e.g., 1.2.14). At a minimum, all
devices on the network (including transmitters), must have the same MAJOR and MINOR firmware version numbers (e.g.,
1.2.x).
Updating the Transmitter
Download the firmware to the receiver.
Access the following menu from the receiver: Device
Configuration > Tx
Firmware
Update.
Align the IR ports between the transmitter and the receiver. IR ports must be aligned for the entire download, which can
take 50 seconds or longer.
Tip: The red alignment LED will turn on when the alignment is correct.
Press ENTER on the receiver to begin the download to the transmitter. The receiver will display the progress of the up
date as a percentage.
Wearing the Bodypack Transmitter
Clip the transmitter to a belt or slide a guitar strap through the transmitter clip as shown.
For best results, the belt should be pressed against the base of the clip.
Tip: The clip can removed and rotated 180 degrees to increase mounting options.
Shure Incorporated
16/24
1.
2.
3.
RF Mute
RF Mute prevents transmission of the audio by suppressing the RF signal while allowing the transmitter to remain on. The
home screen displays RF MUTED in this mode.
From the Radio menu, navigate to Output.
Choose one of the following options:
On: RF signal is active
Mute: RF signal is disabled
Press enter to save.
Turning the transmitter off and on or replacing the battery will restore Output to On.
Safe Start
Power on in Safe Start mode to prevent interference with other devices. Hold the exit button while powering on your device un
til the Safe Start menu appears.
Shure Incorporated
17/24
1.
2.
3.
Safe Start menu options:
RF: Mute or On
Locks: None, Pwr, Menu, All
Use the navigation buttons to make changes.
Tip: To exit the Safe Start menu, cycle the power or momentarily remove the battery.
Note: Previous settings for locks and RF will be retained when the transmitter is powered on in Safe Start.
Input Overload
The OVERLOAD message appears when the audio input experiences a highlevel signal. The power LED turns red as an addi
tional indicator of an overload. Reduce the input signal or enable the input pad to remove the overload condition.
Tip: To enable the input pad, navigate to Audio > Pad and select -12 dB.
Matching Audio Levels with Offset
When linking two or more transmitters to a receiver, there may be a difference in volume levels between microphones or instru
ments. If this occurs, use the Offset function to match the audio levels and eliminate audible volume differences between trans
mitters. If using a single transmitter, set Offset to 0 dB.
Turn on the first transmitter and perform a sound check to test the audio level. Turn off the transmitter when finished.
Turn on the second transmitter and perform a sound check to test the audio level. Repeat for any additional transmit
ters.
If there is an audible difference in the sound level between the transmitters, navigate to the Offset menu (Audio >
Offset) in the transmitter to increase or decrease the Offset in realtime to match the audio levels.
Shure Incorporated
18/24
1.
2.
3.
Tone Generator
The transmitter contains an internal tone generator that produces a continuous audio signal. The tone is helpful when conduct
ing a sound check or for troubleshooting the audio signal chain. The level of the tone is adjustable from -60 dB to 0 dB and the
frequency can be set to 400 Hz or 1000 Hz.
Tip: Always start with the level set to -60 dB to avoid overloading speakers or headphones.
From the Audio menu select Tone Gen.
Set the frequency to 400 Hz or 1000 Hz.
Select Level and use the arrow buttons adjust the value between -60 dB and 0 dB.
Turn off the tone by selecting Off from the menu or by cycling the transmitter power.
Specifications
Mic Offset Range
-12 to 21 dB (in 1 dB steps)
Battery Type
Shure SB900A Rechargeable Li-Ion or LR6 AA batteries 1.5 V
Battery Runtime
@ 10mW
Shure SB900A up to 9 hours
alkaline up to 8 hours
See Battery Runtime Chart
Dimensions
86 mm x 66 mm x 23 mm (3.4 in. x 2.6 in. x 0.9 in.) H x W x D
Weight
155 g (5.0 oz.), without batteries
Housing
Cast Metal
Operating Temperature Range
-18°C (0°F) to 50°C (122°F)
Shure Incorporated
19/24
Note: Battery characteristics may limit this range.
Storage Temperature Range
-29°C (-20°F) to 74°C (165°F)
Note: Battery characteristics may limit this range.
Audio Input
Connector
4-Pin male mini connector (TA4M) or Lemo Connector
Configuration
Unbalanced
Impedance
4-Pin male mini connector (TA4M) 910
Lemo Connector 8.2
Maximum Input Level
1 kHz at 1% THD
Pad Off 8.5 dBV (7.5 Vpp)
Pad On 20.5 dBV (30 Vpp)
Preamplifier Equivalent Input Noise (EIN)
SystemGainSetting≥+20
-120 dBV, A-weighted, typical
RF Output
Connector
SMA
Antenna Type
1/4 wave
Impedance
50 Ω
Occupied Bandwidth
<200 kHz
Channel-to-Channel Spacing
Standard Mode 350 kHz
High Density Mode 125 kHz
varies by region
Shure Incorporated
20/24
Modulation Type
Shure Axient Digital Proprietary
Power
2 mW, 10 mW, 35 mW
See Frequency Range and Output Power table, varies by region
Input Connector Diagrams
TA4M
LEMO
Frequency Bands and Transmitter RF Power
Band Frequency Range (MHz) RF Power (mW)***
G53 470 to 510 2/10/35
G54 479 to 565 2/10/20
G55† 470 to 636* 2/10/35
G56†† 470 to 636 2/10/35
G57 470 to 616* 2/10/35
G62 510 to 530 2/10/35
H54 520 to 636 2/10/35
K53 606 to 698* 2/10/35
K54 606 to 663** 2/10/35
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Shure AD1 Mode d'emploi

Catégorie
Radios bidirectionnelles
Taper
Mode d'emploi

dans d''autres langues